Search Documents

By Derek Morris, Vito Saccheri

In the monitoring of seismic exploration (whether by explosive or vibratory energy sources), the intensity of shaking at neighboring structures can now be measured quite accurately and comprehensively with portable equipment. However, the interpretation of the results is open to considerable debate and mis-interpretation. One conventional approach is simply to compare the maximum measured peak particle velocity (PPV) with a permissible standard – usually 0.5 inches/sec (1.3 cm/sec) because this is the value generally referred to in the U.S. Bureau of Mines standard. This can be very conservative, both for surface structures, and especially for buried structures like pipes, for which absolute reliance on PPV obscures the true complexity of field problems. Quite apart from the fact that the full Bureau of Mines standard is actually a reasonably complex function of frequency (for the simple reason that in differing parts of the frequency spectrum, damage may be displacement or acceleration controlled), the effects of spatial direction and orientation are often ignored.

Jan 1, 2009

By Ginn Huh

The blasting work to construct a subway in Seoul, Korea have often caused increased neighbor’s complaints because of ground vibration. In order to prevent the damage to the structure, it was necessary to predict the level of blasting induced vibration and to determine the maximum charge weight per delay within an allowable vibration level. The effect of blasting pattern, rock strength and different explosives on the blast-induced ground vibration was studied to determine the maximum charge weight per delay within a given vibration level. The blasting vibration was measured from 10 sites along the subway line in Seoul and an empirical particle velocity equation from over 100 test data was obtained, V=K(D/W1’3 )-” , where the values for n and K are estimated to be 1.7 to 1 S and 48 to 138 respectively.

Jan 1, 2000

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By D Vrkljan, Z Ester

Excavating the building pit for the World Trade Center at Rijeka, it was necessary to blast over 160000 m3 of hard mass in fused condition. The building pit is located at a densely populated residential part of the main Croatian port Rijeka, close to the railway-track and traffic routes of the town. The permanent seismic monitoring points are foreseen on endangered housing and infrastructure facilities around the pit during designing and excavation of it. The seismic monitoring has been performed on 15 permanent points by occasion of over a hundred production and continuous blasting operations. The article considers the speeds of ground oscillations depending on applied maximum quantities of explosive charge according to fire degree, total quantities of explosives at the mine-field, structure of explosive charge, applied delay of mine boring and lines initiation mode and rock mass structure

Jan 1, 1999

By Claude R. Ayoub, Charles A. Kliche, David G. McDowall

Homestake Mining Company's Open Cut Mine is located in Lead, South Dakota, in the northern Black Hills. The mine is within 300 feet of occupied residences on the south end, and within 1200 feet on the north end. Mining began at the north end of the open pit in October, 1983, and blasting related complaints began almost immediately. Noise and ground movement comprised the majority of the structural damage claims. As a result of these complaints, Homestake purchased a recording seismograph and began monitoring nearly every blast. In addition, the company hired a consultant to review Homestake's blasting and monitoring practices. He was also asked to do a single, one-time study of the cracks in six homes. This initial work led to Homestake monitoring all blasts with three seismographs and having South Dakota School of Mines and Technology do a year-long study of crack development and propagation in five homes in Lead.

Jan 1, 1989

By Krishna Nand

For assessing the safety of structures during underground explosions, ground particle velocity gives the best damage criteria, and 100 mm/see of ground particle velocity has been internationally accepted as the threshold value of safety (no damage). Results of extensive controlled underground explosion experiments conducted by the author to study the effects of ground vibrations on specially prepared concrete blocks, and also on low rise buildings and dams showed that no damage normally occurred when ground particle velocities were less than 100 mm/sec. Analysis of a large number of accelerograms from a dam site in India also indicated that no damage occurred to normal structures when integrated ground particle velocities were less than 100 mm/sec. Major damage in well built structures like a dam was noticed for ground particle velocity as high as about 350 mm/sec. These results are also generally substantiated from damage data obtained for various structures during other earthquakes, including Elcentro (1940), Taft (1952), Parkfield (1965), and San Fernando (1971). These studies, therefore, suggest that the damage criteria during underground explosions and earthquakes are similar; and 100 mm/see of ground particle velocity seems to be the general threshold value of safety (no damage) against ground vibrations.

Jan 1, 1988

By Florian Bauer

The Fording River mine in British Columbia produces hard coking coal in an open pit operation. Coal seams are exposed by blasting overburden and digging blasted muck with rope shovels. The drilling and blasting process presents a considerable cost factor to the operation. Reducing the amount of explosives needed therefore contributes considerably to costs saving initiatives. However, reducing the powder factor only makes sense if the subsequent loading processes by the shovels are not compromised in terms of productivity.

Jan 1, 2014

By Guo Ziqing, Tang Qiuming, Liu Yuanyuan

The channel-type non-mechanical stirring production process is a new developed technology for emulsion explosives in recent years. It removes traditional equipment such as mechanical-mixing emulsification, mechanical-mixing sensitization, matrix pumping, and explosive pumping, and has been applied in China. This technique achieves a fusion of higher intrinsic safety and lower cost, as well as the excellent quality of products and high efficiency of production. The emulsion particle diameter is about 0.5μm. The storage period of emulsion explosive produced with span-80 emulsifier is more than 7 months.

Jan 21, 2025

By W. Birch

The traditional concept of scaled-distance modelling for predicting blast induced ground vibration holds many drawbacks, not least of which is the major effect data scatter imparts on confidence determination. An investigation by the Department of Mining and Mineral Engineering, The University of Leeds, England has resulted in the development of simple but effective method of improving prediction capacity through the reduction of effective error by incorporating individual location response into a scaled-distance model. The work is the product of an l&month blast-monitoring campaign at a limestone quarry situated in North Yorkshire, England. The data, when presented in the form of a scaled-distance model, indicates a typical scenario where a good overall correlation becomes marred by the extent of data scatter. Examination of the individual monitoring locations however indicates that the response of the individual location is an important factor in the explanation of the large residuals. The novel approach thathas been developed incorporates a series of locational site factors which when incorporated into a scaled distance model reduces the effective error and therefore improves prediction capacity. The approach is based on using a standard computer package “spread sheet” on the understanding that these are commonly available on all quarry or home computers. This approach has been validated by comparison with a more rigorous statistics method.

Jan 1, 2001

By J Edmund Hay, Harry C. Verakisl, Richard J. Mainiero, John J. Mulhern

As the first stage in the rulemaking process, MSHA prepared requirements for the approval and use of permissible explosives and blasting items in underground coal mines. These draft requirements known as "preproposals" were announced in the Federal Register in mid-1984. The draft requirements on the use of explosives were written as a revision to Title 30, Code of Federal Regulations, Part 75, Subpart N. The draft requirements for approval of permissible explosives including sheathed explosives for unconfined applications, approval of water stemming bags, approval of detonators and approval of blasting machines were prepared as Parts 15, 16, 17 and 25 respectively.

Jan 1, 1985

By Dan McCutchen, Oettmeier

Kelly bar drilling and blasting is unique to Florida, the' Bahamas and other marine limestone areas in the world where blast holes are required but will not remain open for the loading of explosives. This type of rock formation usually yields 1.5 tons of recoverable rock compared to 2.2 tons per cubic yard for competent limestone. The loss of .7 tons per cubic yard is due to voids and sand in the formation. These deposits all contain water to the top of the blast holes which are collared only a few ft. above the ground water level. The working pit is a water filled lake which is excavated from the bank by draglines. These drills have been used in Florida for many years to depths of 65 ft or less.

Jan 1, 1991

By Rakesh Raghavaraju, Bibhu Mohanty

Prediction of fracture and fragmentation characteristics of a rock mass subjected to dynamic loads, such as in blasting remains a major technical challenge. The present study is aimed at characterizing the shock transmission properties in controlled experiments in small scale in a well-characterized granitic rock, under varying borehole coupling conditions. Single blast-hole tests were conducted in a granitic rock sample of 145 mm (5.7 inches) diameter and height. The boreholes (in two diameters: 6.4 mm (1/4 inch) or 9.5 mm (3/8 inch)) were loaded with detonating cord of varying charge weight (5.3 g/m or 25 grains/ft to 31.8 g/m or 150 grains/ft of PETN). The effect of explosion gas penetration into the target rock was eliminated by inserting a thin-walled copper liner along the borehole wall. Embedded carbon composite resisters were employed at varying distances from the borehole to measure transmitted shock pressure for two coupling conditions (i.e. air and water) at distances of 1x to 9x the borehole diameter. The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

By Muhammad Yamani, Marsell Riviera, Herry Saputra, Rizky Amin

Drill and Blast processes in hot and reactive ground conditions are a severe challenge in mining, especially in the blasting process. Our main objective is safety issues without compromising the blasting outcome. Safety concerns include unexpected detonation, product damage, and misfire. However, apart from the issue of blasting safety, it is also crucial to maintain good results such as fragmentation, loader productivity, and ore dilution control. Therefore, we use a different product selection method to produce a safe and efficient blast. Pit Araren is one of the pits of the Tokatindung Gold Mine Project in North Sulawesi Province, Indonesia, classified as hot and reactive ground conditions that range from elevation of 25mRL temperature could reach to 98⁰C (208,4⁰F) based on actual measurement. The previous practice for blast holes with temperatures above 70⁰C (158⁰F) loaded with the primer that was specifically designed for hot and reactive ground conditions consisting of detonating cord and packages emulsion that specifically formulated to inhibit exothermic reaction then tied in with a combination of non-electric surface delay detonator and detonating cord initiator (short length non-electric surface delay detonator housed in plastic connector).

Feb 6, 2023

By Rakesh Raghavaraju, Bibhu Mohanty

The paper analyzes the decay of shock pressure as a function of distance from the borehole, and its implication on shock-induced fracture properties of the target rock as the first step in predicting fracture and fragmentation behaviour in a well-characterized rock.

Feb 1, 2020

By Tie-jun Tao, Ming-sheng Zhao, En-an Chi

"Karst landform is a special kind of geomorphic unit which is often accompanied by a large number of geological defects: caves. In blasting engineering, if there are karst caves around the blast-holes, it may result in higher boulder yield and the generation of flying rocks due to the change of burden which is very hazardous for the safety of surroundings. The models of rocks with karst caves from blasting holewere built by the software of ANSYS/LS-DYNA. The results of computation simulation show that thecave can increase more free surface for blasting and leads to a broken zone around itself. Thus rockmass around the cave will fly toward inside and it will result in undesirable result of whole rock mass to be blasted. In addition, the models of rocks with karst caves in different shapes were simulated and thecomputation results show that the caves in round shape have higher load resistance capability than that the caves in rectangle shape. All the simulation results can offer effective guidance for blasting design. The models of rocks with karst caves were built in different distances and shapes from blasting hole by the software of ANSYS/LS-DYNA. The effect of different karst caves on blasting stress and blastingresult were studied."

Jan 1, 2017

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By Catharine L. VanOmmeren

Emulsion quality characteristics such as shelf life, handling, and sensitivity are critical to the end-user. It is therefore important that the consumer be prepared to ask his supplier specific questions. To do so, he needs to have a basic understanding of what an emulsion is and how emulsion properties can affect safety, performance, and environmental impact. The criteria to be covered include: energy, velocity, sensitivity, minimum priming, shelf life, pumpability, effect of AN quality, over-the-road handling, and formulation The consumer will learn how each of these properties can directly affect him. The information will enable him to set minimum standards in product selection, blending, and application.

Jan 1, 1989

By Ravi Sahu, Brad Gyngell, Oktai Radzhabov

Design machine learning approach to simulate the process of muckpile throw distribution before blasting.

Feb 1, 2020

By Chris Breeds, Larry Leone, Jerry Wallace

One of the Authors was recently retained to provide a professional engineering analysis of the potential impacts from underwater blasts used to enlarge intake tunnels at the Cheesman Dam near Denver in Colorado and to design Blast Protection Bags that could be installed in each tunnel to protect the 100- year old downstream valve structures.

Jan 1, 2012

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024