Search Documents

By David Porter, Nathan Rouse

The implementation of presplit blasting has been widely utilized in open pit and underground tunneling. This case study works through the iterative process of developing a heading drill and blast design to control overbreak and limit backbreak in cut and fill headings. The initial design was based on rule of thumb parameters, and the design was then modified for the field conditions based on results. Throughout the design process the drill profile, explosive charge, and timing were modified to yield the best profile compared to design. Data collection during the design process was extensive to best understand the effect of modifying parameters, and gauge performance of design changes. Input from the miners as well as engineers was considered to allow for the best possible adaptation of the design change from existing practices. During the process resistance to change was realized and accounted for to understand the issues that the miners were facing and how to best address them while ensuring high quality blasting. Workforce buy- in was addressed by illustrating the long term benefits of higher quality blasting and the tradeoff of with a slightly more in depth drill and loading cycle.

Feb 6, 2023

By G. Geremia, M. I. Serrano, L. Costa, Strohaecker

The advances in electronics and the development of more efficient algorithms, allow for the designing of more complex and sophisticated automated systems. The new devices include lighter, faster, reliable, and stronger robot manipulators. One available technology, with relatively low cost, is a simple robot manipulator controlled by remote control. The device has been designed to be used in both mining and law enforcement, where it can be useful for inspection, rescue, gas analysis, and even to manipulate dangerous objects, such as explosives. The applications may even include the rescue of trapped miners in risky environments. The major advantage is the fact that the robot can be controlled with a remote and monitored through a video camera, minimizing human exposure to hazardous areas, where robots can perform tasks in an aggressive atmosphere and confined spaces. This article presents a mining robot manipulator controlled by remote control, using video cameras for positioning and sensors for movements, which are located on the operator's arm. With this system, it is possible to create a sensation of virtual reality, allowing easy operation for anyone trained in dealing with explosives, rescues, or other dangerous tasks. Blasting and mining are becoming perfect applications for robots, and its use should increase very soon. The results are discussed and presented for the brand new Xiru 01 robot manipulator.

Jan 1, 2010

By Lon Santis, David Buckwalter, Ken Steinmetz

This paper describes a magazine security system using two readily available cellular telephone-based technologies. The system is comprised of vibration sensors and remote cameras. The system is used at a Bureau of Alcohol, Tobacco, Firearms, and Explosives (ATF) licensed explosives storage location in Pennsylvania to comply with PA Department of Environmental Protection (PADEP) regulations. The system provides instant notification to the licensee via cellular modems, text messaging, phone call, and e-mail. Likewise, the licensee can control the system remotely over the internet and using text messaging commands. The vibration sensors attach to the door of the metal type I magazines magnetically and detect any movement or vibration. The cameras trigger on movement and thermal radiation changes and can also be triggered manually to check alarms received from the vibration sensors. The previous system was comprised of a base unit and magnetic strips. The magnetic strips were powered by a hard line from the control unit and mounted on the doors and top of magazine creating a bond, that when broken triggered an alarm. Our main issues with the unit were the delay in alert times and tech support. Because of these issues, we decided an upgrade was necessary. Compared to that previous system used at this site, these new systems are highly affordable, carefree and reliable.

Jan 1, 2014

By Thomas E. Lobb, Harry C. Verakis

Blasting is a primary means of extracting minerals and ores at surface mining operations. The domestic consumption of explosives and blasting agents during the year 2001 was about 5.25 billion pounds. Flyrock is always a major concern for the blaster. Flyrock from surface blasting operations has caused serious injury and death to employees and other persons. Injuries due to flyrock and the lack of blast area security accounted for over two-thirds of all blasting-related injuries in surface coal, metal, and nonmetal mines during the period 1978-2002. Selected accidents due to flyrock and lack of blast area security in surface mining are presented in this paper. Incidents related to construction blasting are also described. Techniques to mitigate blasting accidents are discussed. These include proper blast design, driller-blaster communication, inspection prior to loading and firing the blast, removing employees from the blast area, controlling access to the blast area, and using a blasting shelter. An experienced driller could detect potential problem areas such as voids, mud seams, incompetent rocks, and other irregularities by observing the progress of drilling. The drill log should include the details of any unusual or exceptional circumstances noticed during drilling. A blaster may need to alter the loading configuration to alleviate potential problems. Basic blast design is sometimes taken for granted and assumed to be proper for the conditions encountered, but one size does not fit all. It is known from the physics of blasting that the explosive energy takes the path of least resistance. The path of least resistance could generate flyrock, depending on the blast site conditions. A combination of ‘borehole tracking’ and ‘laser profiling’ can assist in improving the design of a blast. The blaster can use these tools to adjust borehole loading to match site conditions.

Jan 1, 2004

By Jeffrey Meissner, Mike Waldron, Charles Dowding

Most studies of crack response have focused on opening and closing of a crack in the plane of the wall in which the crack occurs. Crack movement also occurs perpendicular or normal to the plane of the wall. This paper will examine and compare the in-plane and out-of-plane (normal) response of cracks in two different residences near limestone quarries. In two locations, sensors that measure in-plane and normal displacement were installed side-by-side on the same crack, allowing direct comparison of the two modes of response. In a third location, a perpendicular pair of displacement sensors was installed in a corner of a room to observe the bidirectional response of the structure at a corner. Both long-term and dynamic data were recorded with the same sensors; temperature, humidity, and air over pressures were also recorded to compare blast and weather effects. Measurements show that ratios of out of plane to in plane response to dynamic events can vary. However, the ratios of out of plane (normal) response to vibratory events to that of climatological change is still as small as the ratio for in plane crack responses.

Jan 1, 2010

By Rob Farnfield, Ben Williams, Bob Woolley

This paper outlines how drilling safety standards are being driven forward in the United Kingdom’s surface mining and quarrying industry with developments in equipment, procedures and competence.

Jan 1, 2010

By Thomas Rupp, Michael Siegwart

The paper presents the vibration and sound emission measurement campaigns carried out in 2007 in preparation for the Ceneri-Basistunnel construction. We also present the vibration measurement campaign conducted during the construction of the Zimmerberg-Basistunnel. Both tunnels form an integral part of the Swiss Federal Railway Company Neue Eisenbahn Alpentransversale project (NEAT). This strategic project comprised the construction of several new tunnels. Its aim is the improvement of the existing infrastructure. The improved infrastructure will be able to accommodate a larger volume of railway traffic that is also crossing the Alps at higher speeds. The construction of the Ceneri-Basistunnel commenced in 2006. Both the Zimmerberg-Basistunnel and the Ceneri- Basistunnel are located underneath densely populated areas. Therefore, noise and vibration emissions have to be kept to a minimum and must not exceed applicable codes of practice. In order to identify the most appropriate blasting strategy for the yet to be constructed Ceneri-Basistunnel, blasting trials were conducted. The paper presents the findings of these trials and identifies ways to reduce both noise and vibration emissions from blasting. The construction of the first phase of the Zimmerberg-Basistunnel took place between 1999 and 2003. While the first phase is already in operation, the construction of the second phase has been postponed (commencement originally due in 2007). The Zimmerberg-Basistunnel connects the outskirts of Zürich with the city centre. As the tunnel site was not located close to the surface near populated grounds, no special measures were needed to reduce the noise emissions from blasting. However during the construction of the tunnel, the vibration emissions from blasting were monitored on more than 50 locations on the surface. The paper presents the analysis of some of the data. An emphasis is placed on the appropriate synopsis and presentation of data for documentation purposes.

Jan 1, 2009

By G E. Frantii

In the exploitation of low grade mineral deposits, blasting engineers are vitally concerned with maximizing the efficiency of explosive fracturing of rock while simultaneously limiting deleterious environmental affects to acceptable levels. Efficiency can be inferred from radiating seismic waves. Likewise, seismic waves carry direct information on damage potential. The usual approach to this problem is to measure the maximum signal level close to a blast, where it is difficult to instrument and where the signal complexity is intensified by mixtures of wave types and by local heterogeneities. Near-field sites are usually more easily monitored and more readily interpreted. Therefore, a study is being conducted to determine if variations in multi-hole, delayed blasts produce measurable changes in the spectra of seismic waves recorded in the near-field and if these spectra can be correlated with close-in strong motions and affects. To date, power spectra for the well-developed phase Lg and its early coda have been computed and are found to vary measurably when nominal changes occur in blast conditions. Up to a distance of about 50 km the spectra of Lg and its coda appear to be dominated by body wave characteristics (thus source-controlled), whereas beyond 50 km path affects seem to dominate. Additional data must be collected to fully explore the consistency of near-field Lg observations and to verify their usefulness as diagnostics of the engineering affects of blasting.

Jan 1, 1977

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Robert B. Hopler

Explosives have been important to the oil and gas industries since the very earliest days. The first wells of Pennsylvania and New York in the 1860’s were able to be brought back to productivity by the use of nitroglycerin after their porosity was lowered by the high para& content of their oil. Success in the use of seismic waves to locate enemy artillery in the First World War led to the use of explosives in the 1920’s for generating ground vibrations to locate geological structures favorable for the entrapment of oil. Explosives also find widespread use in the more conventional applications of well site preparation and pipeline construction. Explosives applications unique to the oil and gas industries include the jet perforating of casings and formations, fighting well fires, and cutting casing during well shut-in.

Jan 1, 1998

By Cathy Aimone-Martin, Kristin Dunlap Kolden

Blasting was conducted for the Army Corps of Engineers (Corps) in the Columbia River near Saint Helens, Oregon during 2009 and 2010 to deepen the navigation channel as a final phase of a dredging project to accommodate larger container ships. The Columbia River Channel Improvement Project (CRCI) required 4 months to blast and dredge 300,000 yd3 (229,366 m3) of basalt from the bottom of the channel to allow Post-Panamax vessels with drafts up to 50 ft (15.2 m) access to the Ports along the River. Explosives charges were limited to 90 lbs (40.8 kg) per delay for the protection of fish and marine life in the area. A fish mortality study and marine mammal monitoring program was also required by the Corps. Underwater overpressure monitoring was required for each blast and peak overpressures measured 10 ft (3.1 m) above the river bottom 140 ft (42.7 m) from the closest blast hole were not to exceed 70 psi (483 kPa) with a cautionary level of 40 psi (276 kPa). Specifications required sampling rates of 500k S/s and PCB Peizotronics tourmaline pressure sensors. The Corps granted permission to co-locate additional ceramic-type sensors at different sampling rates to design redundant monitoring systems 140 and 300 ft (42.7 and 91.4 m) from blasting and develop a site-specific overpressure attenuation model for the project. This paper presents the correlations of overpressure with cube-root scaled distance factors, a comparison of measurements using three different pressure sensor systems, and a discussion of blast design influence on overpressure measurements.

Jan 1, 2014

By Philip H. Porter

Ammonium nitrate blasting agents continue to be the work-horse of the explosives industry. The versatile, low-cost, anfo products, whether packaged, poured, or bulk, continue to produce superior results for the explosive consumer who understands their limitations and capabilities.

Jan 1, 1984

By D. C. Valdemeri, Oppermann J. P. Z., R. G. Schaarschmidt, C. S. Mendonca

This case study was conducted in an aggregate company, located at Estância Velha town, RS, Brazil. The study was based on the results of vibration monitoring mainly in terms of PPV (peak particle velocity) and frequency. Changes in the blasting design were performed to adjust the limits determined by the Brazilian standard NBR 9653:2005. Understanding the seismic wave attenuation for the site, changes in the blasting design were tested to fit the limits, such as reduction of maximum charge per delay, initiation orientation and sequencing and finally the replacement of accessories like "shock tube" by electronic initiation system. The results are shown below.

Jan 1, 2015

By Jung-Hoon Ryu, Chang-Ha Ryu, Byung Hee Choi, Yang-Kyun Kim

Control of overbreak in tunnel blasting is one of the key factors affecting the construction expenses as well as safety. Overbreak causes an increase in the cost of construction by requiring an additional amount of shotcrete. In addition, blast damage to the final rock face may cause instability and rock fall hazards. For these reasons, controlled blasting is an indispensable routine in tunnel excavation in order to get a smooth face and to reduce damage to the final wall. We have experienced a very poor quality of excavation depending on the tunneling sites although a similar design of controlled blasting technique was applied. Field experiments over 40 rounds were carried out to investigate the cause of the poor results in tunnel blasting. In this paper, discussed are the parameters affecting the overbreak and some findings from the field experiments. Overbreak could be controlled considerably by adjusting some parameters before the efforts of developing a new blasting method.

Jan 1, 2004

By E. Contestabile, B. von Rosen

On August 5th, 1998, a tractor-trailer carrying approximately 18,000 kg of blasting explosives, struck a rock face on the side of the road near the town of Walden, Ontario. Eye-witness accounts of the incident state that there was an intense fire for approximately 30 minutes before the detonation. The detonation caused severe damage to the tractor-trailer, shifted the pavement and caused blast damage to the rock face. A rock fragment was recovered almost 2.5 km from ground zero and a 70 kg piece of an axle assembly was recovered over 1 km from the site. Windows were cracked at distances of almost 3 km.

Jan 1, 2001

By Lewis L. Oriard

Some two million cubic yards of sandstone and orthoquartzite were blasted and excavated at Upper Stillwater Dam, located high in the Uinta Mountains in northern Utah. The material was processed to produce concrete aggregate for the construction of the largest roller compacted concrete (RCC) dam ever constructed, and one of just a few in existence. The dam cross-section is shown in Figure 1. The aggregate was sound rock produced from required dam foundation excavation and from a quarry located about 1/2 mile from the dam site. Representative compressive strengths of the sandstones and quartzites were in the range of 20,000 to 30,000 psi.

Jan 1, 1993

By Lon Santis

This paper describes several applications of quantitative risk assessment in the management of commercial explosives operations. The Institute of Makers of Explosives’ (IME) quantitative risk assessment software modeling program IMESAFR was used for this analysis. Modeled activities include the unloading of a ship at port, locating a safe haven, and dealing with encroachment on a manufacturing facility. The layout of actual explosives sites were used for the analysis. The risk of fatality is analyzed and shown it can be used to make informed operational decisions for each activity. A study of the risks to individuals from activities involving commercial explosives compared to individual risks from other daily activities or exposures is also presented.

Jan 1, 2008

By R. Narendrula, S. P. Singh

The productivity of a loading machine is affected by several factors. One of the most significant is the characteristic of the muck being loaded. A study was conducted to examine the effects of the looseness, angle of repose, size distribution and moisture content of the blasted material on the efficiency of the loading machine. The study was conducted in the following stages: (a) controlled experiments in the lab, (b) tests with loader simulator and (c) field work in an operating mine. It was found that looseness (%void) in the muck increases with the increase in the value of the mean particle size and index of uniformity of the fragmented rock. Looseness and angle of repose affect the fill factor and the digging cycle time of a loader and in turn the productivity of the equipment. Moisture content affects the angle of repose as well as the stickiness of the material to the loader’s bucket. It was observed that the angle of repose increased with the increase in the mean particle size and the moisture content of the muck. It was also found that the bucket full factor and rate of scooping decrease with the increase in the values of mean particle size and index of uniformity. This was also conformed during fieldwork that bucket fill factor decreases with the increase in the mean particle size as well as the index of uniformity.

Jan 1, 2005

By Lawrence W. Hallanger

Anaheim Bay, located at Seal Beach, California, is the site of the Huntington Harbor development of waterfront homes and marine facilities. The main entrance to Anaheim Bay is a relatively narrow channel connecting the bay with the Pacific Ocean which runs under California State Highway One. During the development of Huntington Harbor the old highway bridge was replaced with a new, higher bridge to allow for boat passage through the channel. At that time only the main span decking of the old bridge was removed, leaving the support pillars and the approach ramps in place (see Figure 1). The narrowness of this channel, plus the increasing boat traffic created a situation in which public demand for the removal of the old bridge became significant. Because the bridge was located within the boundaries of the Seal Beach Naval Weapons Station (see Figure 2) the Navy became involved in the bridge removal. Eventually the task was assigned to the Naval Amphibious Construction Battalion One and work began in early 1974.

Jan 1, 1975

By Ricardo González Dumuihual, Carlos Scherpenisse

A monitoring campaign to record dynamic pressures generated by detonation of a single blasthole was implemented at Barrick Gold´s Pueblo Viejo Open Pit mine (PVDC), located in the Dominican Republic . Pressure amplitudes beyond the dynamic compressive strength of the electronic detonator´s capsules have the potential to damage these electronic devices, generating misfires along with all the associated risks and entailed safety implications. In most instances, misfires generated from high dynamic pressures are a direct consequence of drilling deviations resulting in blasthole distances smaller than originally designed.

Feb 1, 2020