Search Documents

By Tom Paynter

In an underground mining environment, the primary method of firing a blast is using a combination of an electric detonator and a detonating cord to initiate the Nonelectric detonators. This method has been in use since the 1970’s. A firing line is used which can be subjected to damage and the need for constant testing and maintenance.

Jan 1, 2017

By O Omidi

Selection of delay times to optimize fragmentation has been a controversial topic among researchers and blasting practitioners. This paper reviews previous experimental information and presents the results of new tests conducted in small blocks constructed using a commercial grout. The effect of the delay on the average fragment size, coarse fragmentation and uniformity of fragmentation is discussed. Fragmentation was coarser at extremely short or extremely long delays, while a fairly constant average size was obtained at a variety of intermediate delays. Uniformity, defined as the slope of the fragmentation distribution through the average fragment size, was poor at short and very long delays and relatively constant at the intermediate delays. Some tests attempted to minimize the effect of gas penetration by lining the boreholes with copper tubes. When this was the case average fragmentation changed marginally, while uniformity was significantly affected by delay and was typically smaller than in the unlined tests.

Jan 1, 2014

By Gungor Tuncer, Ali Kahriman, A. Kadir Karadogan, Savas Gorgun

The environmental problems arisen from ground vibration and air blast have been faced and discussed frequently in various industries such as mining, construction, quarry, pipe line etc. where blasting is unavoidable operation. Structural damage due to ground vibrations creates great socio-economic problems for mine and quarry management as well as for the people residing in its vicinity, therefore in bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. With the general trend towards larger blasts in mining and infrastructure excavation, ground vibration and air blast problems and complaints have significantly increased. With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision, therefore determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. In another word, prediction of ground vibration components is extremely important for the minimisation of the environmental complaints. Estimating of particle velocity and other components of ground vibration with reliable approaches will give important facilities to the blasters. Although many studies had been carried out to isolate environmental problems induced by blasting in the past, a general reliable formulae has not been established yet. Due to restrictions on the complexity of ground motion, blasting and test site factors, experimental studies are still necessary for each site to minimise environmental issues. This paper presents the results of ground vibration measurements carried out during the excavation activity for contruction of an organised industrial region located nearby Istanbul in Turkey. The major rock type is granite that is encountered at this site. Within the scope of this study, in order to predict peak particle velocity level and produce a site-specific propagation curve for this site, ground vibration components were measured for blast events during bench blast optimization studies over a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and delay detonators (firing) were used as explosives. While the parameters of scaled distance (charge quantity per delay and the distance between the shot and the station) were recorded carefully, the ground vibration components were measured by means of two different vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statical analysis and evaluations an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site.

Jan 1, 2000

By A. S. Tawadrous

This paper is an evaluation of Artificial Neural Networks (ANN) as a tool in the design of the geometry of surface blast patterns. The built model uses eight different parameters, which affect the design of the pattern. Those parameters are rock type, stratification, blasthole diameter, bench height, type of explosive, priming position, powder factor and fragmentation size required. The network was trained to predict burden and spacing of the blast pattern. The model was built and trained (back-propagation technique) using 43 case histories collected from the literature. The model has then been validated using 16 cases from operational quarries.

Jan 1, 2006

By Terri Jordan, Gregory Hempen, Thomas Keevin

Water-borne blast pressures from confined blasts were recorded as part of a submerged blasting program in Florida for channel deepening. The blasting was confined within the rock floor by stemming. Shot patterns of stemmed borings were recorded, as were two open-water shots. One hole of one shot was not confined properly, which allowed comparison of confined and a poorly confined larger charge weights per delay. The pressure data were intended to gain information on typical pressure measures from the rock removal program relative to impacts on marine organisms. Water-borne pressures from actual confined, rock-removal shots validate the hypothesis of lessened impacts to aquatic and marine biota.

Jan 1, 2007

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By Luan Monteiro, Francisco Biulchi

The AngloGold Ashanti - Cuiaba mine sought innovative approaches to minimize lateral development and stope extraction time while maintaining optimal gold recovery and minimizing dilution. The stope 8GAL EXT 30 was selected as a case study. Traditionally, conventional blasting methods in such a scenario would necessitate either a single mass blast or slot development at each end of the stope. These methods typically compromise recovery and dilution or increase development time and risk. Additionally, conventional wired detonators require workers to re-enter the stope between blasts to load blastholes and connect detonators. The wireless initiation system offers a solution by initiating blastholes using magnetic induction signals that can penetrate rock, air, and water. This technology allows a pre-charged stope to be mined without requiring workers to re-enter the area between blasts to charge and connect blastholes. Engineers from Orica and AngloGold Ashanti designed a new extraction sequence utilizing the wireless initiation system. The process began with the opening of one end of the stope using a conventional slot and wired electronic detonators. Subsequently, pre-loaded rings were fired in three blasts to extract the opposite end and the intersection. The 8GAL EXT 30 stope was successfully mined using this technology enabled method. Each blast was meticulously monitored, and the stope void was scanned to assess blast performance. The results demonstrated a 4.6% improvement in recovery and a 16% reduction in dilution compared to the initial plan, and reduced exposure of people to hazardous locations in the stope. These results represent an additional value of USD 200k, gained from implementing wireless initiation to enable this particular blasting schedule.

Jan 21, 2025

By William Nicoll

Those who use electric detonators in firing blasts will be interested in a new electrical testing instrument known as the ‘Blasters’ Friend’, recently devised by the New York Blasting Supply Co. of New York. Owing to the necessarily delicate construction of the platinum wire bridge in the shell of a detonator, it frequently happens that it becomes broken or disconnected; thus destroying the circuit and rendering the detonator worthless. In many cases, misfires and premature explosions are caused by defective detonators. Heretofore, to detect the deficiencies of a detonator before using has been an impossibility, owing to the absence of a testing instrument adapted to the purpose.

Jan 1, 2010

By B. Papilon

Dynamic pressures during blasting can affect performances of both electronic and non-electronic detonators. Boreholes can develop tremendous amount of pressures during blasting. The effect of such elevated pressure especially during electronic delay countdown is probably more acute in electronic detonators. Measuring the pressures during blasting can aid to understand the relationship between magnitude of the pressure developed and the multitude of blasting conditions.

Jan 1, 2013

By Lifent Li, Jhon Silva-Castro

Since millisecond-delay detonators were first introduced, at least two variables, among others, have been more closely considered when timing a mining blast: the accuracy and the precision of the initiation system. Currently, most mine blast design software has the capability to use the precision/accuracy of the firing system and display the overlap timing window between charges in any given time interval (8 ms, 3 ms, etc.). Despite these technological advances, there are still situations which result in the overlapping of charge timings. The consequences of overlapping charges involve flyrock events, fragmentation and diggability problems, and other inconvenient situations affecting the operation of the mine.

Jan 1, 2015

By Calvin J. Konya

Backbreak behind the last row of boreholes can be a significant problem for blasting operations. Backbreak will interfere with the proper drilling and execution of the subsequent shot and can produce well defined boulders, which will not be broken by the subsequent shot. In order to determine the effect of timing on backbreak, a full scale blast with 6 1/2 inch boreholes was used to test the effects of timing. The test site was a quarry which had suffered from severe backbreak regardless of the blasting pattern or explosive used. One half of the production blast was loaded and initiated using the current technology at the quarry, the other half of the blast was deliberately timed in such a manner as to minimize backbreak. The timing was such to allow for ground movement in one row before the subsequent row fired. The test results proved that the amount of backbreak and flyrock could definitely be controlled with the selection of the proper borehole timing.

Jan 1, 1987

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

By L C. Taylor

Both the U. S. Navy and the U. S. Army are interested in knowing more about the loading applied to vehicles which are unfortunate enough to encounter a detonation of a buried mine in the course of performing their normal duties. The Dynamic Effects Laboratory at the University of Maryland has been involved in small scale testing for ten years to assist the Navy and the Army in understanding the loads that are applied to personnel carriers when a buried explosive detonates beneath them. This paper describes results from small scale tests conducted to determine the loading mechanisms on target plates when subjected to loading due to the detonation of a buried mine in saturated sand, dry sand, and water. Transparent target plates were utilized in order to determine the loading process beneath a floor board on armored vehicles. Various charge sizes were scaled in the laboratory accordingly to a standardized full size threat encountered in the battlefield. Tests were conducted in saturated sand, dry sand, and water keeping the stand-off distance of the target and the depth of burial of the charge constant. In the case of water impacting a transparent PMMA plate the crack propagation was recorded and the crack velocity is determined. Additional tests were performed in saturated sand by varying the stand-off distance of the target but keeping the depth of burial of the charge constant. The small-scale test results could be scaled to full scale by using verified scaling laws.

Jan 1, 2016

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By John Hutchings

Drilling and blasting is a clearly delineated work process, which has well defined inputs and outputs. Drilling and blasting is also a process with a number of steps each of which has measurable outcomes. Drilling and blasting is ideally suited to the application of Total Quality Management principles. Most drilling and blasting information is generally poorly managed with disjointed and unrelated Information Technology systems managing parts drilling and blasting data. Data is often moved from on system to another, sometimes manually. In the field, drilling and blasting is still very much a paper based system and which has not generally benefited from some of the recent hardware and software technology advancements now “on the shelf”. Data collected on paper rarely is transcribed back into an electronic system for further analysis. It is often difficult to collate or review historic drilling and blasting data. This paper will present a definition of Total Quality Management and demonstrate how it can be applied to the drilling and blasting work process. Total Quality Management defines the mechanisms for the application of continuous improvement to drilling and blasting. Continuous improvement will provide opportunities to modify drilling and blasting work process outcomes and generate real cost benefits within the overall mining process. A complete drilling and blasting management system frame work, called DBS, is presented in this paper. DBS provides all the components necessary to implement a full drilling and blasting Total Quality Management solution. Also highlighted will be appropriate “off the shelf” technology that can be applied to replace current paper based systems and provide the means to connect with other mine data systems. Various examples will be discussed which will demonstrate potential benefits of applying a structured Total Quality Management approach to a drilling and blasting work process.

Jan 1, 2004

By Jeffrey Meissner, Charles Dowding

Cracking is one of the concerns cited by owners of structures adjacent to construction or mine blasting. During the past decade a large number of measurements have documented the low level of crack response produced by typical, ground motions compared to those produced by climatological effects. These data support the observation that there is a level below which ground motions do not cause even cosmetic cracking. As with all new findings, these crack response measurements need to be thoroughly investigated for all possible alternative interpretations. Among these alternatives is that uncracked locations are more affected than cracked locations. This paper presents measurements to shed light on the influence of existing cracks and the response of uncracked, but weak locations. Blast and weather induced responses of cracked and uncracked areas of gypsum wall board are compared in two structures: one near a surface coal mine in Indiana, the other near a limestone quarry in Florida. The ground motions that excited one of the structures were unusual in that the dominant excitation frequencies of 5 Hz were near the structure’s natural frequency and amplitudes exceeded 0.7 ips (18mm/s).

Jan 1, 2011

By Robert Hopler

Testing Stations Abroad At the Seventh International Congress of Applied Chemistry, Drs. Mente and Will communicated a paper on the above subject. All large coal-getting countries employ testing stations of some kind, in order to safeguard, to the highest possible extent, the lives of the men employed in this industry. Most countries employ galleries of considerable diameter, and fairly short length; but within recent times, long galleries, with drives and other accessories approaching as closely as possible the actual conditions of mining have been installed. The following are the details of the testing stations employed in the countries mentioned.

Jan 1, 2010

By A. Cobbii, M. Kasliki, W. Birchi

The Department of Mining and Mineral Engineering at the University of Leeds has a long history of research into the environmental impacts of blasting from quarries and opencast mines. This paper gives an outline of a detailed case study into the structural damaged induced in a rock walled tunnel with a brick lined crown due to close proximity quarry blasting. The test site Taffs Well Quarry is located in South Wales in The United Kingdom and has a disused railway tunnel situated within the south eastern comer of the quarry site. Quarry development plans included the working of this area and therefore the deliberate destruction of the central section of the tunnel.

Jan 1, 2001

By Greg Wyartt

"At an Australian iron ore open-cut mine, 129 separate blast patterns (consisting of 38.5 million tonnes /42.4 million US tons, equaling 28% of annual blasted tonnes) were initiated using electronic detonators. 87 patterns were designed as per site methodology using ‘vectorial’ initiation timing sequences (blast direction and relief specified only), while the remaining 42 patterns were designed with interactive initiation timing sequences - hole by hole sequencing based on the measured site specific primary shock wave (P-wave) velocity and distance between blast-holes. The intention of this project was primarily to reduce material size presented to the crushing circuit, and also to determine if productivity benefits could be obtained by the use of interactive timing."

Jan 1, 2017