Search Documents

By J. E. Misiewicz, A Rozendaal

Paper presented at Geofluids '93, held in Torquay, UK, 4-7 May 1993. The tin field consists of a fragment of Lower Proterozoic volcanosedimentary rocks surrounded by granitoids. Almost all the significant deposits are hosted by arkoses and are classified as replacement and space-filling types, with particular styles of mineralisation dominating at different mines. Petrological and geochemical investigation of borehole cores from four centres indicated the presence of a stratified zone 500-600 m thick and continuous over at least 20 km along strike, consisting of pervasively altered clastic arenitic sediments. The alteration is zoned into a grey-green sodic albitised footwall, an 80 m thick sericitised-tourmalinised sulphidic tin zone and a red haematitic potassic hanging-wall. The zoning and the localisation of three cassiterite phases are consistent with the tectonic history and with multiple pulses of stanniferous hydrothermal fluids derived from late differentiates of the granites over a prolonged period. Areas of high fracture density acted as conduits for the fluids, whose initially rapid ascent was retarded by decreasing pressure contrast, limited development of fracturing and/or impermeable shaly arkose to cause lateral spreading and pervasive alteration over a broad, stratified front. Lateral overlapping of local fronts at the various centres suggests a continuous zone, while the many petrological and geochemical similarities point to a shared fluid composition

Aug 1, 1995

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By R. K. Zipf

The sudden, violent collapse of large areas of room-and-pillar mines poses a special hazard for miners and mine operators. This type of failure, termed a cascading pillar failure, occurs when one pillar in the mine layout fails, transferring its load to neighbouring pillars and causing them to fail in succession. Recent examples of this kind of failure in coal, metal and non-metal mines in the USA are documented. Mining engineers can limit the danger presented by these failures through improved design practice. Whether failure occurs in a slow, non-violent manner or in a rapid, violent manner is governed by the local mine stiffness stability criterion. This is used as a basis for three design approaches to control cascading pillar failure: containment with barrier pillars during pillar splitting; prevention with panel pillars of high width-to-height ratio and small-centre mining; and full extraction by retreat mining

Jun 19, 1905

By D. C. Bailey, D. I. Hodson

Paper presented at the annual joint meeting of the IMM and IMinE held in Harrogate, 31 January 1991. The Neves-Corvo copper-tin mine is the highest-grade large-tonnage copper operation in the world and is now arguably the most significant producing base-metal mine in Europe, rating in the top ten world producers of both copper and tin. A description is given of the initial exploration work and the development of the project from the orebody discovery in the Iberian Pyrite Belt of southern Portugal in 1977 to full operating capacity in 1990. The chronological account includes discussion of the main organisational, financial, technical and environmental decisions and of the various difficulties encountered, and the challenges of the future are identified. The project was brought in on schedule and within budget

Jan 1, 1991

By B. M. England, C. Y. Yang, L. T. Matthews, J. Y. Yin

The domestic concentrate used by the Shanghai Meishan Metallurgical Corporation in Nanjing contains significant siderite, magnetite and haematite, the siderite having a substantial influence on its sintering behaviour. On the basis of experimental findings and published information it is proposed that siderite decomposition starts at c.400 degrees C and results in the formation of CO and/or H2, which then reduces the haematite to magnetite prior to the initiation of high-temperature sintering; inter-mixed particles of Australian haematite and pisolite ores also undergo significant reduction. As the gaseous reduction process is so effective, low-temperature forms of silico-ferrite of Ca and Al (SFCA) cannot form even at high sinter basicity. The bench-scale results were confirmed in a pilot-scale facility whose sinters consisted mainly of magnetite, high-temperature SFCA and glass, which is typical of sinters formed from mixes with high magnetite levels

Aug 1, 1995

By D. C. Goldring

Many high-grade iron ores are considered to result from the supergene enrichment of banded iron formations. The secondary processes may be related to either present-day or ancient erosion cycles and may reach a considerable depth. Other high-grade ores hosted by banded iron formations are regarded as either sedimentary or metamorphic in origin although often also subjected to the secondary processes. The evidence for this multiplicity of origins is reviewed with descriptions of selected deposits: Kedia d'Idjil and M'Haoudat in Mauritania, Bomi Hills and the Nimba Range in Liberia, the Itabira district in Minas Gerais, Brazil, and El Pao in eastern Venezuela. Emphasis is placed on the recognition of textures that show that some ores are tectonites, the precursor materials having undergone pervasive deformation accompanied by metamorphism. The question whether such ores are pre- or syntectonic is difficult to resolve, the evidence being inconclusive, but a diagenetic/early deformation origin is preferred. The possible range of origins has to be taken into account in exploration, particularly as regards the depth of drilling, and in the characterisation of ores for metallurgical use

Jul 1, 1991

By R. Poulin, C. F. Gleeson

The Birimian rocks of the region are gold-bearing and show many similarities to those of Burkina Faso. All three greenstone belts (Goroual, Tera and Sirba) host gold-bearing quartz veins. It appears that, contrary to previous misconceptions, lateritic terrain is not an unfavourable environment for exploration geochemistry. This is demonstrated by the results for the Koma Bangou area, where soil and termite-mound geochemistry have been successfully used in the search for gold. Soil provides an effective sampling medium where it is shallower than about 2 m; there is evidence that some soil anomalies are enhanced by the presence of secondary (botryoidal) gold. In areas of thicker, allochthonous soil cover, termite-mound sampling is more effective. At Koma Bangou an identified resource of some 11 100 000 tonnes with an average gold grade of 2.44 g/t has been reported. The gold mineralisation occurs in quartz veins and stockworks aand in the wallrocks of shear and fault zones that trend N, NW and NE. The host rocks are a granodiorite-syenite porphyry and intermediate metavolcanic rocks and tuffs

Apr 1, 1996

By D Macdougall, J Otto

The financing of large mining projects in developing countries is often achieved, at least in part, by limited-recourse financing methods. Financing agreements are affected by the basic accord that is struck between the host government and the sponsors of the project. It is concluded that governments and project sponsors should take into account the requirements of lenders when structuring such mineral development agreements to maximise the potential for attracting project financing. Lenders are likely to be most interested in aspects such as fiscal arrangements, calculation of taxable income and general accounting rules, royalties, transferability of payments/dividends overseas, corporate structure and control, staged development, financing, loan support and state guarantees/approvals, political risk, provisions for default, product marketing, settlement of disputes and environmental issues

Aug 1, 1994

By J. A. Hudson, X. D. Pan

A rock mass responds to excavation according to the properties of the intact rock, the network of contained discontinuities and the susceptibility of the rock mass to weathering. Large deformation often occurs when one of these components causes the rock mass to have a low strength relative to the stress conditions. Analysis of such large deformations forms a significant feature of current numerical modelling in rock mechanics. A practical large deformation problem of roadways in a coal mine is described, demonstrating the requirements for improving numerical techniques. The development of a numerical model is then summarised with particular attention to several concepts pertinent to large deformation analysis in geomechanics. A numerical case study is presented in which the developed finite-element model is used and the results are compared with the in-situ measurements. Conclusions are drawn for rock engineering that are also relevant to both civil engineering and mining engineering projects

Sep 1, 1991

By M. Lombardero, J. Garcia-Guinea, J. Taboada, B. W. Roberts

The structural, textural and mineralogical properties of the slate formations of NW Spain make it the most important district in the world for quarrying roofing slates. Over the past 10 years the introduction of new methods has increased yields from 2 to 13%. The main factors affecting quality are quartz grain size less than 75 micrometres, homogeneity of slaty cleavage and S0-S1 intersection angle, very low metamorphic grade, absence of secondary foliation, beds 10-12 m thick and low content of oxidisable Fe sulphides. The two main controls on fissility are lithology and deformation accompanied by metamorphism. The minimum natural block size should be 0.6 m3 but this volume can be reduced for modern cutting tools such as diamond wire, chain and circular saws. Structural analysis is crucial in exploration and quarrying, as shown by the prospecting methodology applied at Dominio de Truchas in central Spain and the computer analysis of rock mass discontinuities at Casaio quarry

Jun 19, 1905

By L. J. Barnes

The process for bio-remediation of sulphidic slag (BROSS) operates at 45 degrees C in a neutral (pH 7), aerobic aqueous environment in which sulphide in the slag is converted to sulphate. A two-stage version has been developed that involves quantitative chemical pre-oxidation of total sulphide to thiosulphate, followed by complete biooxidation of thiosulphate to sulphate. Ferric hydroxide, also produced, acts as a flocculant in the bioreactor effluent, concentrating heavy metal precipitates in the thickener as a sludge which can be returned to the smelter. The process has a high sulphate production rate and low acid and nutrient consumptions. Microorganism growth is the rate-limiting stage, requiring a minimum liquid residence time in the bioreactor of about 7 h. Although large quantities of oxygen are needed, sufficient gas mass transfer can be attained in an air-lift reactor. Products are an aqueous stream containing sodium sulphate with only trace levels of toxic heavy metals and a benign, toxic metal-containing sludge

Jun 18, 1905

By S. Babendererde

The twenty-ninth Sir Julius Wernher memorial lecture of the IMM, presented at Tunnelling '97, London, 2-4 September 1997. The tunnelling industry is well prepared to face the challenge from the population explosion in urban areas in the near future. Many well-established yet redundant concepts are still impeding progress, however, including the prediction of excessive surface ground settlements. The correct selection of TBM can minimise these, and ground deformations can be avoided completely if the appropriate techniques are applied. Advanced techniques have been used in the Tokyo Bay Crossing, where the tunnel lining was installed by robots. Other advanced techniques include the use of a sliding slip form to give temporary support to an extruded tunnel lining, the chemical processing of ground by polymers during earth-pressure balanced tunnelling and the use of electronic monitoring and steering devices in TBMs. There will be challenges to tunnelling in urban environments, as open cut techniques will no longer be tolerated. Two examples of mined stations are briefly discussed

Jun 19, 1905

By C. L. Schneider, C. O. Gomes, R. P. King, J. A. Finch, D. Lin

Discussion is presented by Prof. King and Dr. Schneider of the paper by Lin, Gomez and Finch published in Trans.IMM C, vol.104, 1995, p.C155-C161. They conclude that the correction procedures used for simulated observations of simulated capped spheres are not reliable when applied to mineralogical data and that their relative ranking should not be extrapolated to other situations. Properly regularised solutions obtained with the use of appropriate kernels can be safely used for routine mineral liberation work and can be calibrated accurately against real mineralogical samples in the laboratory

Jun 19, 1905

To maximise recovery by highwall mining, pillars must be designed which are long, slender and of relatively low width-to-height ratios. The strength of pillars with width/height less than 2 depends primarily on the mechanical response of the coal, due to the reduced influence of frictional restraint between roof and floor. A suitable pillar design approach therefore requires a method of estimating coal-seam properties. Experimental studies were carried out to determine ways of reliably predicting the large-scale mechanical properties of coal seams from small-scale test data. The studies led to a method of practical, systematic assessment of coal-seam properties based on measurement of coal rank and seam brightness profiles. The criterion employs the parameters sigma(c), m and s of the generalised Hoek-Brown empirical strength criterion for rock masses. A novel design approach combines the flexibility of modern numerical modelling programs with simple hand calculation for rapid assessment

Jun 21, 1905

By E Oktay, I Yusufoglu, C Kahruman

Powder and spherical pellets of MoO2 were oxidised under controlled conditions in the temperature range 674-791 K at oxygen partial pressures of 8.1-30.4 kPa. Weight increase during the reaction was determined by thermogravimetric analysis. It was concluded that the reaction is 0.6th order with respect to oxygen concentation and that the activation energy is 148 kJ/mole. In experiments conducted with powder, fast transfer of reaction heat to the gas phase created isothermal conditions, but the temperature of pellets rose by a maximum of 54 K at 674 K and 105 K at 791 K. The rise in temperature caused structural changes such as sintering and crack formation, which had a considerable effect on the reaction rate. The findings should be taken into account in the design of equipment and choice of operating conditions for roasting MoS2

Jun 21, 1905

By Qing Wang, H. Sevim

Belt network simulators are the most widely used models in the design of belt networks. The simulators developed in the past two decades are reviewed and their limitations are discussed. To overcome these limitations and to provide a design model that can be used efficiently in real-life applications, a comprehensive non-simulation model has been developed. The features of this model are briefly discussed. A real example is used to demonstrate the model's superiority over belt simulators

Sep 1, 1991

By D. M. Evans, D. L. Buchanan

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. The Zinca area was chosen as a suitable location for an investigation of the weathering and secondary dispersion of platinum group metals from the Zone. It was concluded that platinum is immobile while within weathered rock, its mineral phases tending to alter from primary sulphides and tellurides to secondary Pt-Fe alloys. Palladium is variably mobile in weathered rock. In stream sediments Pt occurs mainly as small, dense, discrete particles, giving rise to a nugget effect, whereas Pd probably occurs as much finer particles or chemically adsorbed on to a suitable substrate. Pt shows a rapid decrease in sediments downstream from mineralisation, whereas Pd has a much slower downstream decay

Apr 1, 1994

By H. Forster, F. H. Koenemann, U. Knittel

The greenstone belt developed along the Sandawana line, an anastomosing, transcrustal shear zone. The lode gold is concentrated in veins and along brittle-ductile shear zones and other faults. Gold contents of 200 rock samples were found to be well below economically significant levels, excluding purely syngenetic deposit formation. Average gold content of unmineralised banded iron formation decreases from 7.3 ppb in the east (Manica) to 1.6 ppb in the west (Odzi), where depletion reflects hydrothermal leaching. The mineralising fluids may have been generated during deep crustal deformation, metamorphism and magmatism. Gold was hydrothermally deposited during carbonatisation and sericitisation of ultramafic and mafic rocks and during hydrothermal overprinting of banded iron formation and felsic rocks. It is present in native form and as microscopic to submicroscopic inclusions in pyrite, arsenopyrite and pyrrhotite. Argentiferous galena and other sulphides are commonly observed. Rezende, which produced over 38 t Au, is hosted by a granodiorite stock. By-product gold was produced from Cu-Ni sulphides at Mundonguara. The deposits are related to the older, but not the younger, of the granitoids intruding the belt's supracrustal sequences; the estimated age of mineralisation is 2700-2600 Ma. Odzi district, with 61 mines, has produced only 3.5 t Au as its higher-level host rocks have apparently been eroded. Mutare (formerly Umtali) district, with 133 mines and 9 placers, has produced 68 t Au (65 t from Rezende and adjacent deposits), and Manica district, with 23 mines and 8 placers, 12 t Au. Estimated reserves for the Rezende area are 20 t Au and for Manica district 4 t lode Au and 19 t placer Au

Apr 1, 1996

By J. M. Jimenez, G. D. Schena, A. J. Cazorla

A full-scale Deister column was operated in parallel with the conventional cleaning bank of cells and a pilot Jameson cell in parallel with the conventional rougher cells. Flotation column performance was appreciably enhanced by use of an improved washing system and an internal launder. The performance of the rougher bank of cells, Jameson cells, cleaner cell bank and column were described by simple linear functions. These allowed calculation of overall circuit recoveries and evaluation of alternative circuits. An evaluation procedure based on a financial criterion is demonstrated with a simplified example, illustrating how revenues and operating margins are often of more concern than concentrate grade and recovery

Jun 18, 1905

By D. R. Wardrop, G. Walton

Paper presented at the UK minerals industry conference held in Leeds, UK, 3-5 April 1995. A description is given of the approach that has been taken to the design of the 550 000 000 t superquarry with a planned life of 60 years that is proposed for development. The quarry has been designed to replicate a corrie and a sea loch and will include excavated slopes more than 570 m high. The main geological and physical controls on the layout and the choice of development method are outlined. The operation phasing is presented and the geotechnical constraints on slope design and the feasibility of alternative quarry limits are discussed. Environmental considerations have been dominant in planning and the quarry has been specifically designed for closure

Jul 1, 1996