Search Documents

By E. L. Chanturiya

During the mineral processing of pyrites sulphide ores of some deposits of Russia loss of gold with tailings and pyrite concentrates amounts up to 40%~90%. The problem of selective allocation of gold-bearing pyrite is crucial. There are 4 mineralogy-technological groups of pyrite determined in copper-zinc sulphide ores, based on the increase of contents of gold in pyrite. The gold associated with group 4 pyrite contents of 85% the total mass of gold found in the pyrite. The flotation behaviour of the enriched fractions of pyrite (98%), of the allocated from the ore of Gay deposit, were studied essentially in various conditions ?? and the charge of Butyl xanthogenate of potassium (ButX). Some products of selective pyrite flotation were investigated by methods of scanning electronic microscopy, energy-dispersive and X-ray spectral microanalyses, definition of specific resistance and thermoelectric moving force.

Jan 1, 2014

By Zhang Yuejun, Feng Tianran, Shen Zhengchang, Han Dengfeng

"With continuous mining industry development and dressing plant scale expansion, flotation cell is developed towards to large scale and intelligence. Based on flotation cell scale-up theory and industrial practice, KYF-320 air-forced mechanical flotation cell with effective volume of 320m3 was successfully developed by Beijing General Research Institute of Mining and Metallurgy (BGRIMM) and adopted by China Gold Inner Mongolia Mining Co., Ltd, Luming project of China Railway Resource Group Co., Ltd, and Toromocho project of Chinalco in Peru. In this paper, the structure and technical characteristics of KYF-320 flotation cell are introduced, and the application of that equipment in China Gold Inner Mongolia Mining Co., LTD is demonstrated. The tank of KYF-320 flotation cell is cylinder-shaped, 8200mm in diameter and 7500mm high, with double froth lauders and large inclined angle cone bottom. 16 sets of KYF-320 flotation cells of which the processing capacity is 26,000,000 tons/a, are used in the second phase project of China Gold Inner Mongolia Mining Co., LTD. Their stable running shows the long life of impeller and stator and the power intensity (power consumption divided by effective volume of flotation cell) of KYF-320 flotation cell is only 0.73kW/m3 which is significantly less than that of small scale flotation cells. The industrial production obtains good results that the Cu grade of final concentrate of entire flotation circuit is 22.90% at the recovery of 86.73%, when Cu grade of feed is 0.35%, which indicates that KYF-320 flotation cell has good performance and can be widely used in large scale mine."

Jan 1, 2014

By C. Martinez, S. Helle, M. Pincheira

We studied the feasibility of automated mineralogy to discriminate between tennantite and enargite, the main sulfosalts found in the Rio Blanco deposit, Codelco-Chile, in order to predict the content of minor elements (As, Sb, Ag, Pb, Zn) that impact on the process and concentrate prices. The identification of these minerals is feasible using traditional microscopy, however not possible by automated mineralogy. This drawback prevents comparing the databases generated in the past by means of conventional microscopy with the information obtained at present by QEMSCAN. To differentiate enargite from tennantite the mineral composition of both sulfosalts was studied by electron microprobe. The presence of associated minor element contents of about 8% zinc in tennantites and not exceeding 0.07% in enargites were used to modify the SIP database of QEMSCAN to enable the quantification of these phases in samples of head, residue and concentrate coming from As-bearing domains of the deposits. Detection limits allowed to determine the mineral species in the head, concentrate and residues. The integration of methodologies such as automated mineralogy and microprobe can be used successfully to quantify the presence of some ore forming solid solution.

Jan 1, 2014

By Axel Pankewitz, Andrew Smith, Mathias Stender, Christian Behrens

"Particle size measurement is one of the most important factors in obtaining peak performance of the mineral processing plant in order to ensure efficient milling and flotation circuit operation. Off-line particle distribution analysis technologies only allow an infrequent check of the ore slurry size and hence do not allow for timely process monitoring or intervention. Most existing on-line particle size analysers suffer from a variety of disabilities such as poor statistics, non-representative sampling or mechanically complex setup. This paper will describe an Ultrasonic Extinction based method which overcomes many limitations of existing online analysers and has proven its performance for mineral applications over many years. Installation examples will be given. Since new technologies usually raise e questions about comparability and agreement to common particle size analytical methods e.g. sieving or laser diffraction analysis, extensive studies were performed comparing these different technologies to quantify the quality of results as well as its mathematical robustness."

Jan 1, 2014

By L. Pan

As an air bubble approaches a mineral surface, a thin liquid film (TLF) is formed in between. The excess pressure (p) in the film determines the kinetics of drainage, which is of critical importance in flotation. We have developed a new method of monitoring the kinetics for both stable and unstable wetting films and analyzed the results using the Reynolds lubrication theory. It has been found that initially a TLF is thinned by the Laplace pressure (pcur) due to changes in bubble curvature and subsequently by the disjoining pressure (?) created by the surface forces present in a wetting film. In the present work, we have derived an analytical expression for determining ? from the temporal and spatial profiles of TLFs on mineral surfaces. The results show that ? > 0 in a film formed on a hydrophilic surface and ? < 0 in a film formed on a surface hydrophobized by collector. Thus, the role of collector in flotation is to create a hydrophobic force and hence a negative disjoining present in wetting films. It is also found that smaller bubbles can create higher Laplace pressure, which helps the TLF drain faster.

Sep 1, 2012

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"In this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 - 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 - 3.0x103 mol/m3 NH4OH, 0.4 - 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration.For gold recovery from the pregnant solution, the trioctylmethyl ammonium chloride (TOMAC) was used in this investigation as an extractant to extract gold from thiosulfate solution without pH and other adjustments. The effects of gold concentration, pH, ammonia, thiosulfate and cupric ionic concentrations, extractant and diluent concentrations and retention time on the gold recovery were investigated. It was found that 180 mol/m3 extractant diluted with n-octant at O/A ratio of 1:1 could extracted the 100% of gold in 0.6 ks from the thiosulfate solution at the optimal leaching conditions. The 100% gold stripping could be achieved with 10% thiourea solution."

Jan 1, 2003

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

By Yang Xiao, Zhang Yimin, Bao Shenxu, Liu Chun

Stone coal is a unique vanadium-bearing resource in China. Many techniques, such as salt roasting-water leaching, blank roasting-acid leaching, direct acid leaching etc. have been developed for vanadium extraction from stone coal. The vanadium leaching rate can reach 74.9% for stone coal from Jiangxi, but only about 27% of vanadium is leached for Hubei ore by applying salt roasting-water leaching technique. This paper investigats the vanadium occurrence in stone coal by microscope observation and electron probe, and compares the minerals components of stone coal from Jiangxi and Hubei. Although most vanadium exist as an isomorphism by replacing Al(III) from dioctahedral structure in mica group minerals in stone coal from two regions, the free vanadium is remarkably abundant in Jiangxi stone coal than in Hubei stone coal, which results the fact that vandium is relatively readily extracted from former. Moreover, the content of calcite in Hubei stone coal is much higher than that in Jiangxi stone coal. Calcium can react with V2O5 to form water insoluble calcium vanadates during roasting and this may be the reasone why the water leaching rate of vanadium is low for Hubei ore. Acid leaching is more beneficial to the vanadium leaching but other extra methods, such as adding aid-leaching agent and/or increasing acid concentration is need for the ore where vanadium is embeded firmly. This study can effectively guide the selection of vanadium extraction techniques for stone coal from different regions.

Jan 1, 2014

The simulation study on the process of iron ore beneficiation plant of Essar Steel, Kirandul was carried out. The iron ore fines and slimes generated nearby Bailadila mines of NMDC are used as raw materials for this beneficiation plant. The capacity of the plant is 1400 TPH operating in parallel in two streams. The capacity of the plant was utilized about 60% of throughput capacity. To improve the plant capacity as well as quality performance, the simulation study was conducted to detect the bottleneck of the process. The process samples were collected from input and output of each processing unit operation to generate the data base for simulation study at the feed rate of 400 and 500 TPH of iron ore fines in a single stream. The characteristics data i.e., breakage and selection functions were generated using MILLSOFT package for simulation of ball mills. Then MODSIM package was used to evaluate the performance of each unit operation to identify the bottleneck. It was established by a simulation study that the intermediate thickener draws high current when the feed rate is more than 400 TPH due to high torque drawn by rotating rake because of presence of coarse particles in the input stream to thickener. The problem was sorted out by classification of input stream of thickener to remove the coarse particles. Then the process was simulated at its rated capacity, and experimental validation studies at the plant were also conducted at the feed capacity of 600 and 700 TPH by modification of process flowsheet. The experimental data was almost matching with simulated data. Finally, the processing plant is running with full rated capacity without any bottleneck. Keywords: simulation of ball mill, breakage function, selection function, iron ore

Sep 1, 2012

By André Mans, Frans B. Waanders

Current losses of Ferrosilicon (Fe-Si), which is used in the dense medium separation (DMS) of iron ore at Kumba Resources, Sishen, South Africa occur due to adhesion to the separation products and also by being present in the effluent stream, due to abrasion. The losses contribute greatly to the running cost of the plant and the purpose of this project was to determine the characteristics of the unused Fe-Si and then to characterise the changes that occur during storage and the use thereof. A Scanning Electron Microscope (SEM) and Mössbauer Spectroscopy (MS) were used to investigate the characteristics of the fresh and used Fe-Si. It was found that the biggest loss of Fe-Si was due to the abrasion of the particles during the DMS process, which resulted in the liberation of Fe and subsequent formation of an oxihydroxide froth. A possible change in magnetic properties was also observed, leading to further losses that could occur during prolonged use of the medium. No clear changes to the Fe-Si occurred during correct storage methods, as was initially thought.

Jan 1, 2003

By John Starkey

"The development of the Minnovex SAG Power Index (SPI) Test in Canada has created a new and accurate way to measure ore hardness in a SAG environment. Coupled with the standard Bond Ball Mill Work Index Test it is now possible to determine from these two relatively inexpensive laboratory tests, the amount of energy required to grind an ore from the primary crushed size to the desired liberation size. By testing multiple samples to discover where the hard and soft ore zones are located, the representative hardness distribution for the ore body can be determined and grinding equipment selected that is capable to meet production targets for all mining areas of the deposit.In the last century, it was deemed prudent to select up to 50-tonne samples of ore for Semi Autogenous Grinding (SAG) pilot plant tests and a second 5-tonne sample for metallurgical pilot plant work. The methods outlined in this paper show how the 50-tonne sample is no longer required for SAG design because it is better to measure the representative hardness distribution of the ore body than the hardness of a “chosen” representative sample. This is demonstrated to be true by the fact that the lower horizons of an ore zone cannot initially be accessed to recover 150mm pieces, and the bulk samples taken, rarely represent the desired design hardness of the ore. Median hardness will not yield a good result in most cases and a clear understanding of the location and extent of the hardest zones is imperative to achieve a truly successful grinding circuit design.This paper discusses two plants (Kubaka and Agnico Eagle) that have been designed using SPI and Bond with no pilot plant test backup. Both have been very successful in that they can grind design tonnage on the hardest ores in the mine. This guarantees that the mine’s profitability is protected in any mining sequence. It also allows the extra power to be converted to higher throughput on softer ores if additional cash flow is needed. The advantages from the owner’s point of view are dramatic. This procedure will be attractive as well when considering the costs for test work, and the samples for testing. Existing diamond drill core is normally used and this allows the inclusion of data from the deepest regions of the mine. In addition, it is also clear that the decision to use a crusher can now be made at the design stage of a project based on measured parameters and the estimated capital costs of alternative designs."

Jan 1, 2003

By Ghislain Bournival, Seher Ata, Graeme J. Jameson

A common method to prevent bubbles from coalescing in a flotation cell is by the addition of surfactants, called frothers. The gas dispersion properties in a column were tested for solutions of 1-pentanol, tri(propylene glycol) methyl ether, and poly(propylene glycol) in the presence of sodium chloride. The dependency of surfactant on the gas holdup can be divided into regions. It seemed that for a sufficiently low concentration of surfactant, even a stronger surfactant could show a transition in gas holdup from constant/decreasing to increasing with concentration. This region, however, was not marked by a decrease in the average bubble size. In addition, PPG gave higher gas holdup values while averaging larger bubbles. On the other hand, sodium chloride mostly affected the gas holdup when the concentration was high enough to prevent bubble coalescence. Another parameter affecting the gas holdup was the superficial gas velocity. A linear dependency was found between the two under a bubbly flow regime. The current study showed that both surfactants and salt could slightly affect the influence of the superficial gas velocity on the gas holdup.

Jan 1, 2014

By Darryel Boucher, Raymond Langlois, Neil Rowson, Kristian Waters

The Knelson Concentrator is a centrifugal gravity concentrator composed of a high speed rotating bowl into which a mineral slurry is fed. The rotational motion creates a centrifugal acceleration up to an equivalent of 200 G. Under this acceleration, particles enter fluidised riffles along the side of the bowl, with the fluidisation allowing for the substitution of dense material for less dense. The separation mechanism is not fully understood and questions remain on the optimal residence time, slurry feed parameters and bowl surface profile to achieve a better separation. The positron emission particle tracking (PEPT) technique has been applied to record the motion of a -1700+1180 µm particle of a quartz-gold matrix, labelled with 18F radioisotope while it undergoes concentration inside a 3" laboratory scale Knelson Concentrator (KC-MD3) operated at 60 G. The slurry used was composed of quartz and magnetite. Particle trajectories during the first stage of the concentration process where the heavier particles centrifuge through the increasingly dense slurry towards the riffles of the bowl are shown with respect to time. This work reveals new information on particle motion inside the Knelson Concentrator and the results will be used for validation of developed separation model as well as optimisation of a centrifugal concentrator’s performance.

Jan 1, 2014

By Osvaldo A. Bascur, J. Pat Kennedy

"The profitability of mining and metallurgical operations continues to lag behind that of other industries despite the technical advances that have occurred in recent years. A primary reason for poor performing in this economic sector is the lack of integration of mining and metallurgical information. The mine cut-off grade can be optimized if mining and metallurgical engineers have the data to optimize milling for the type of ore in hand.Integration of mine transactions, stockpile inventories, process flows and assays is the key to determining the economics for each blast strategy in a mining site. Real-time information from manufacturing assets greatly affects the profitability and flexibility of a company, but gross errors from faulty sensors, inaccurate instrument calibration, or incorrect process models may corrupt actionable information. New software tools can model the process, sift through available data to identify and eliminate gross errors, and use statistical data reconciliation to create materially balanced and consistent readings. The reconciled data is unified for use by both monitoring and decision making processes.Creating a real-time information environment where upgrade and change are allowed is becoming an accepted methodology to accelerate and simplify the integration of applications such as production monitoring, equipment performance management and yield and inventory management.This paper describes the data integration requirements in a mine, concentrator and port for unification of the redundant data. The capture of the mining events, stock pile management and the metallurgical information is the base requirements for a dynamic environment to reduce the overwhelming amount of information to unified set of information. Part of any decision support program should entail these results to continuously improve the measurement system to address the costs in mine and milling the ore."

Jan 1, 2003

By Y. P. Huang

Experiment results and operation practice on reutilizing old tailings dumped at SCIM (Shang-chang Iron Mine) of KISCO (Kunming Iron and Steel Corp.) are presented. In a production period over 30 years SCIM dumped about 8 million tons of iron ore tailings. For improving resources utilization instead of wasting, experiments on processing for reutilization of the old tailings are con-ducted. These tailings are fine size fractions of weathered iluvial ores rejected out by classification- des-liming in ore washing and dressing processes, containing TFe 21%~22% in hematite mainly and limonite occasionally. Their particle size distribution, in average, is of 72.26% minus 0.037mm and 30.88% minus 0.005mm. Existence of plenty of micro-fine particles makes the tailings refractory to process, resulting in poor metallurgy. The whole sample of the old tailings without size-classification is fed into experimental process. Slon-100 type high grads WHIMS (wet high intensity magnetic separator) with cyc-pulsing is adopted, which magnetism-focusing rod?s diameter is changed from 3mm into 2mm. Operational conditions of optimizing rougher separation tests are strengthened. An iron concentrate assaying 52.21% Fe at quantity rate of 18.39% and iron recovery of 44.40% is obtained. Operational practice shows that metallurgy and economy of the old tailings treatment are close to what achieved at experiments. It is estimated, therefore, that some 1.4 million tons of this iron concentrate may be recovered from the old tailings. This means that KISCO has moved its key one-step in re-mining and reutilizing the secondary resources, which would be a good demonstration in this industry. This is also of social and economic significance in response to China government?s request on reducing consumption of resources and establishing society with economy for achieving sustainable development.

Jan 1, 2014

By M. Kanuchová, J. Briancin, M. Achimovicová

"Faculty of Mining, Ecology, Process Control and Geotechnology, Technical University, Košice, Slovakia An industrial eccentric vibratory mill was used for direct and short-time mechanochemical reduction of ilmenite concentrate (FeTiO3) and anatase (TiO2) with magnesium metal powder in order to reduce Fe and Ti resp. and hereby to convert them to the more soluble phases suitable for further hydrometallurgical processing. X-ray diffraction analysis of FeTiO3 after 60 min of milling with Mg confirmed the presence of Fe0 and Mg2TiO4 phases and for TiO2 after 180 min of milling the new TiO and MgO phases have appeared. X-ray photoelectron spectroscopy has detected Fe0 (metal) and Mg2+ species which are corresponding to the product of FeTiO3 mechanochemical reduction. The product of TiO2 mechanochemical reduction has revealed XPS spectral lines corresponding to Ti2+, Ti4+ and Mg2+ species on its surface. Morphology of mechanochemically reduced samples was studied by scanning electron microscopy analysis. Subsequent leaching of mechanochemically reduced FeTiO3 and TiO2 was performed in dilute HCl and H2SO4 at 80oC and compared with mechanically activated samples. The recovery of Ti has reached 100% for FeTiO3 and 79% for TiO2 after 60 min of leaching. Based on this study the flowsheet for possible processing of natural refractory titanium ores patented by author was adapted and documented. INTRODUCTION Ilmenite (FeTiO3), along with rutile (TiO2) represents the most important titanium resource necessary for titanium industry, for production of titanium metal, alloys and pigment grade TiO2 which are becoming more important and versatile for various industries such as an aircraft and aerospace, navy, chemical, automotive, medical and offshore wind industries, for machine and plant engineering and architecture as well, mainly due to high corrosion resistance. Pigment grade TiO2 is utilizing in pigment, plastic, glass, paper and rubber industries (Zhang, 2011). There are obvious research efforts for development of the potential alternatives to the expensive thermo-chemical commercial processes of titanium raw materials processing. Zhang (2011) has summarized conventional thermo- a electrochemical processes which involved a combination of pyrometallurgical, hydrometallurgical and electrometallurgical technologies and highlighted the improved hydrometallurgical routes promising for commercial application in the future. Such improvement could also be mechanical activation of FeTiO3, TiO2 by high-energy milling which causes their structural disordering, the changes of physical and chemical properties, consequently and has a positive effect on the dissolution kinetics (Achimovicová et al., 2014a, 2017, Baláž, 2008). The various types of mills such as a planetary ball mill, a vertical ball mill, a drum mill, an attritor were used for mechanical activation of FeTiO3 as a pretreatment process for subsequent leaching (Achimovicová et al., 2014)."

Jan 1, 2018

By O. V. Suvorova, V. G. Minenko, D. V. Makarov, A. L. Samusev, E. A. Selivanova

"Saponite is a valuable marketable product widely used foundry, metallurgy and construction, in the chemical, food and consumer goods industries, in medicine, and in agriculture.The feasibility of producing of high-quality construction materials with enhanced physical-chemical and decorative characteristics from saponite-containing products has been given a scientific basis and experimentally validated. The compressive strength of the samples in the sintering temperature range of 800-1000 ?? varied between 35 and 80.9 MPa; the bending strength 8 and 26.7 MPa, which is superior to the high-grade ceramic bricks of the M-300 brand. It has been established that the saponite-containing product obtained using the electrochemical separation of process water has a high sorption capacitance relatively the heavy-metal ions such as nickel and copper (40.7 and 99.8 mg/g, respectively). As a result of sintering at 750 ?? the sorption capacity of the sorbent for the nickel and copper ions increased to 194.2 and 212.8. Using the XRD and SEM with energy-dispersive spectroscopy studies, we diagnosed the metal-containing phases and validated the metal sorption mechanism.This study opens up the possibility of practical realization of the saponite-containing product as high-quality building materials and heavy-metal sorbents while addressing the issue of process water treatment. INTRODUCTION The Lomonosov deposit of the Archangelsk diamondiferous province accommodates 10 kimberlite pipes. The anticipated volume of diamond-bearing ore and dump rock to be removed before reaching the open-pit mining limit is 300 mln t (Karpenko, 2009; Bezborodov, etal. 2003). Rock in the deposit is almost completely displaced by clay minerals, predominantly saponite, amounting to 90% in the vent facies (Karpenko, 2009)."

Jan 1, 2018

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003

By V. M. Mankov, O. V. Zamyatin

"Fine free gold at a size of minus 250-100 µm can be effectively recovered from mineral materials (buried clay placers, saprolites, gold-bearing aggregates, technogenic sands etc.), or MM, using some developed and implemented in practice cost-effective basic technological schemes of MM processing at every stage: exploration, main concentration processes, upgrading of gravity concentrates etc. Such technologies are based on mineral materials composition, different content of fine gold mass fractions, and include improved two-stage sluicing technology, jigging technology, advanced technology and integrated technology. The main operation principle of the given technologies is gravity concentration. They provide recovery of fine gold of any size from MM, including gold finer than 100 µm, using concentration systems and plants with a capacity of 1-2 and up to 100-200 m3 per hour. Selection of a cost-effective technology depends on its technical and economic viability regarding to mineral material composition, optimum performance and concentration rate. The developed technologies of mineral materials concentration establish a balance between technological, technical and economic factors, and ensure profitable development of deposits containing free gold and characterized by a complex composition of concentrating material. Free gold recovery with these systems increases by 2.0-2.5 times for gold particles at a size of minus 250+100 µm and 10-30 times for gold particles of minus 100 µm, compared to conventional sluicing systems. The Irgiredmet Institute has developed and supplies primary concentrate washing machines for upgrading gravity concentrates of up to 100 mm in size, with a capacity of 1.0-5.0 m3/h, fitted with various production equipment including pyro- and hydrometallurgical systems. Additionally, the Irgiredmet Institute develops and manufactures systems of mechanized processing of geological and technological samples (UOMP; registered design certificate No.27505, Russia) designed for complete recovery of free gold in the process of geological samples handling and decreasing of a human factor influence. A system includes a package of technologically associated disintegration, classification and concentration equipment with some “know-how” elements that provide effective recovery of fine gold at the exploration stage. A number of Irgiredmet’s patented technologies and systems (patents of the Russian Federation) have no equivalents in the field of mineral processing and provide designing of technologically practical and cost-effective flowsheets that offer higher recovery of gold of different sizes (fine gold), at every stage of processing of mineral materials including basic concentration processes, upgrading and exploration etc."

Jan 1, 2018

By Fang Liu, Xin Tan, Zhong-ming Wang, Yan-bo Shang, Jie Zhao

"The flotation separation of sulphides bulk concentrate containing Cu, Zn, Mo and Bi, which was obtained by both table-flotation of gross sand of gravity separation of wolframite and bulk flotation of wolframite slimes using butyl xanthate and oil No. 2, etc., has been conducted by using the cyanide process in the tungsten concentrator. The process has problems of high reagents consumption (25 tonne of cyanide dosage per year) and mineral processing cost (800~1000 RMB reagents cost per tonne of by-product concentrates), high mutual containing loss in the by-product concentrates and serious environmental pollution caused by lots of cyanide-containing wastewater. In order to solve this problem, a new cyanide-free separation technology is studied, which is used to process this sulphides bulk concentrate with 8.68% Cu, 8.98% Zn, 0.26% Mo, 1.58% Bi and 40.12% S. The results of the closed circuit test show that Cu, Zn, Mo and Bi can effectively be separated from this sulphide minerals concentrate by using the reasonable flotation-gravity flowsheet, high-efficiency collectors and regulators simultaneously. The metallurgical recovery and concentrate grade are as follows: molybdenum recovery is 94.63% with 50.62% Mo content; copper recovery is 85.18% with 29.29% Cu content; zinc recovery is 75.92% with 46.49% Zn content; total Bi recovery is 65.08% with 16.86% Bi content. The new technology is an alternative to the cyanide process due to its low cost for reagents, satisfying separation results and economic profits, and solves the problem of environmental pollution caused by the use of large quantities of cyanide. Some important parameters in separating the Cu-Zn-Mo-Bi sulphides concentrate are also introduced in this paper. This study provides pretty good technical support for separating the polymetallic sulphide ores containing Cu, Zn, Mo and Bi by cyanide-free technique."

Jan 1, 2014