Search Documents

By Yu. Gurevich, M. Teremova, I. Prokopev, A. Razvjaznaya, N. Algebraistova

"The objective of this work is the scientific justification and development of efficient and environmentally-friendly method of bulk concentrate preparation for selection with application of microbiological practices. This research suggests to apply Pseudomonas Japonica bacterial culture to the bulk concentrate before the selection circuit in order to clear the surface of sulphides from the xanthate skin. It is also suggested to apply bacterial consortium Ochrobactrum ?nthropi and Pseudomonas aeruginosa JCM 5962 for desorption of diesel residual concentrations. High-efficient and environmentally friendly method of copper-molybdene and lead-zinc bulk concentrate selection was developed based on theoretical and experimental research work with application of microbiological practices. In comparison with conventional methods (steaming, sodium sulphide washing) the above suggested bio-technological method of bulk concentrate preparation before selection cycle will allow to reduce material and power expenditures, and it is also environmentally friendly. INTRODUCTION High-efficient selection of sulphide bulk concentrate is gained exclusively after collecting agent is removed from mineral surface. Therefore, the problem of bulk concentrate preparing before the selection cycle is acute, since the further technological parameters of the subsequent separation depends on the effectiveness of pulp preparation. Existing traditional ways of bulk concentrate preparation. such as washing or steaming, are characterized by high energy and material costs in industrial conditions [1,2]. The microbiological treatment before separation of the bulk concentrate into different kind of concentrates appear one of perspective processes for treatment of bulk concentrates [3,4]. At the present time, the world practice of processing mineral raw materials demonstrates the wide application of technologies using microorganisms: bacterial leaching and oxidation, purification of industrial wastewater. This is due to the fact that biotechnological methods are environmentally safe, low-cost, and suitable for refining complex ores and raw materials of industrial origin."

Jan 1, 2018

By W. P. Roux

With depletion of higher grade iron ore reserves, and the need to process finer, lower grade material; there is a need to better understand the recovery efficiency of jigging process. The use of Positron Emission Particle Tracking (PEPT) was examined as a technique, to study the motion of particles inside a laboratory batch jig. PEPT is a noninvasive method that can provide three dimensional kinetic data of a particle during jigging. Particles with different densities and sizes were traced under the same jigging parameters, to obtain a data set that can be used for the development and verification of jigging models. From the results, detailed information on the stratification rate of a particle was obtained, with adequate resolution to see particle movement through an individual pulse. Detailed data of this nature is critical for the validation of CFD and DEM models. Keywords: positron emission particle tracking, jigging, jig models

Sep 1, 2012

By Jens Markowski

The EU Directive 2000/53/EC on end-of life vehicles (ELVs) states that in 2015 at least 85 wt.-% of a vehicle has to be reused or recycled. This result in the obligatory need to separate additionally metallic and other components of the automotive shredder residues (ASR), so that they can be professionally prepared for recycling and reuse further. Currently the iron-containing fines of ASR are deposited as it is not possible to process in blast furnaces due to its particle size (< 4 mm), composition and material properties. Additionally problems are also caused in handling and transportation (dust) of the material. This work focuses mainly on the ASR materials utilization in blast furnaces. Material was further separated into two consecutive fractions by carrying out repeated crushing and magnetic separation twice. The two fractions have significantly higher iron content (up to 75 wt.-%) compared to the initial material mixture. The materials were assessed for their usage in blast furnaces based on the possible pelletisation with and without binders, stability of pellets, shape and size of pellets, etc. Pelletisation of the material was carried out with a single mould pellet press. Further lignite coal was added to the mixture as additive which improved the pelletisation behavior and the mechanical stability of pellets. Lignite coal was chosen as a reducing agent in the blast furnace process contributing towards additional savings in energy supplied. The experiments reveal that the production of pellets from iron-containing fines is possible with a lignite coal admixture of about 15 wt.-%. These pellets displayed good mechanical stability and can be used in blast furnace processes in recovery of the recyclable metals which are currently not recycled. The recycling of not yet recyclable metals would reduce the deposition and can be easily adopted into the economic cycle by their utilization. Keywords: Automotive shredder residue (ASR), FE-fines, pelletisation

Sep 1, 2012

By Michael. H. Moys, Clayton Bhondayi

An electro-resistive measuring technique developed by the authors was used to study the effects of superficial gas velocity and froth height on froth phase bubble sizes as a function of height above the pulp-froth interface. Flotation tests and the bubble size measurement were carried out in a laboratory mechanical flotation cell that was operated in a pseudo-steady state mode using primary rougher tailings slurry from Lonmin Platinum as feed. The values of intra-bubble impact distances (IIDs) which are the estimates for froth phase bubble sizes obtained from the measurements indicated that as superficial gas velocity was increased, the values of IIDs decreased for the two froth depths tested. Increasing froth height at fixed gas rate resulted in an increase in IID values especially close to the froth surface. Changing froth height and gas rate alters froth residence times; longer froth residence times mean more time for bubbles to coalesce hence larger values of IIDs and vice-versa.

Jan 1, 2014

By Ming’an Wei, Chuanyao Sun, Yangge Zhu, Fayu He, Yanbo Shang, Xingrong Zhang

In order to discuss the separation mechanism of copper-molybdenum ore, surface electronic structures of chalcopyrite and molybdenite were studied in the paper, by using First Principles method of quantum chemistry. So, the separation mechanism of thioglycolic acid (TGA) with chalcopyrite and molybdenite was revealed better. The results showed that differences of the electronic structure of chalcopyrite and molybdenite could directly affect their interactions with TGA, such as band structure, density of states, Mulliken populations, and so on. And the frontier orbitals of chalcopyrite and molybdenite were also calculated by Dmol3 after the optimization by CASTEP, from which the interaction energies between minerals and TGA were obtained and compared. So, the essence of flotation separation of copper and molybdenum were well revealed.

Jan 1, 2014

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014

By S. P. Das

Tumbling mill is an important unit operation in a mineral processing industry whose operation needs to be understood to make it an energy efficient unit. One of the important mill parameters is the impact spectra generated by collision of the moving charge mass on the mill shell. This process also generates mechanical vibration on the mill shell and propagates to the plumber block of the mill. In this work, we tried to understand the impact spectra by using different minerals such as Banded Hematite Quartzite (BHQ), Hematite and Quartz as mill feed of a semi-autogenous (SAG) mill. The said mill is of 1000 mm diameter and fitted with a force sensor on the mill shell and a vibration sensor on the plumber block. The analysis of the impact spectra was done by taking into consideration the peak impact force above a certain threshold value. It clearly shows that the impact force decreases as the particle size become finer irrespective of the mill feed material. This can be used as an effective tool by the mill operators to have an understanding of the mill product size reduction. The mechanical vibration tapped by a tri-axial accelerometer was analyzed by power spectral density analysis. The vibration signal analysis shows the variation in the power spectrum magnitude both at lower and higher frequency. It also shows inconsistency in case of BHQ where it shows a significant decrease in vibration at lower frequency and increase in vibration at higher frequency. Therefore, the impact spectra analysis is a better method compared to vibration analysis in understanding the mill product size reduction.

Sep 1, 2012

By Claudio L. Schneider, Reiner Neumann

Any serious study of stereological conversion procedures must be based on an as accurate as possible complete fractionation of a real mineralogical texture. The original work on the Dolomite- Sphalerite Magstream? separation provided excellent data for establishing a working stereological conversion procedure, which has been successfully applied to a number of ores since its implementation. The linear grade distributions measured from these fractionated particles have been published and are accessible. The procedure for stereological conversion from areal measurements is exactly equal to the procedure for linear measurements. Particle composition from the dolomite-sphalerite density-fractionated particle sets, derived from both linear and areal data (Figures 1 and 2, respectively) are redundant, after proper transformation, and match the particle’s compositional range (plotted against S.G.) expected from Magstream?; direct density measurements by Hemicropicnometry plots within the ranges. Linear data cannot be used without conversion, but areal measurements are often directly applied as liberation spectra. Our areal measurements, without stereological conversion (Figure 3), differ completely from the results after transformation, and its density range falls mostly out of the expected/measured values. Therefore non-transformed areal data cannot be directly applied as useful liberation information.

Jan 1, 2003

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By M. Ranjbar, M. Khosravi Rad, A. Tohry

"The filling degree is defined as the volume ratio of the load inside the mill, which determines the power drawn from the motor, as long as the filling degree is not more than the optimum level. As the filling degree increases beyond the optimum level, the impact energy inside the mill will decrease and as a consequent, the mill power output will also decrease. Therefore, the mill filling degree is a key parameter in evaluating the grinding circuit performance, as it determines the mill reaction to the input feed. Since this parameter has an impact on the mill capacity, measuring the mill load is vital for control and optimization of grinding process. As in Choghart Processing Plant no instrument is available to measure the AG mill filling degree, an empirical model based on the bearing-oil pressure is proposed. The AG mill filling degree was related to the differences between the average pressure of input and output bearings, the circulating load and power drawn. It was shown that a quadratic model could relate the mill filling to the above mentioned measurements. This model showed that when the power drawn and circulating load decreases the bearing-oil pressure needs to be checked. If the bearing-oil pressure increases the feed rate needs to be decreased and steel ball be charged to the mill to increase the grinding and prevent mill overloading. INTRODUCTION The feed quality (size and hardness) affects the grinding process in AG mills. Reducing the top feed size and increasing the ore hardness reduce the mill efficiency and increase the particles with critical dimensions inside the mill. These will result in increasing the mill filling degree and reducing the mill throughput and efficiency (Wills and Finch, 2015). The volume ratio of the load inside the mill is called filling degree, which determines the mill power drawn. It is believed that if more energy is mainly spent on grinding (Wills and Finch, 2015). Therefore the mill power draw is used as a mean to control the mill efficiency."

Jan 1, 2018

By G. Merazchiev

In the selection of copper ? molybdenum concentrates with the use of reagents containing sulfide ion ? sodium sulfide, sodium hydrosulfide etc for depression of copper minerals and pyrites, big part of depressor is oxidized by oxygen, which is dissolving in pulp during aeration with air in flotation machines and it is expended unproductively. This is the main reason for the big expenditures of depressor, reaching up 15~20 kg/t collective concentrate and the high exploitation expenditures for the copper ? molybdenum selection. Effective direction for lowering expenditure of depressor and increasing of the technical ? economical effectiveness of moly production is the conducting of the selection in nitrogen medium. In the paper are shown the results, obtained by applying of this direction in selection of collective copper ? molybdenum concentrate from the porphyry copper deposit ?Ellatzite? ? Bulgaria, in which the ratio Mo:Cu is over 1:120. In laboratory conditions, through comparative experiments in medium of air and nitrogen are defined: expenditure and initial concentration of NaHS in pulp for effective depression of copper minerals and pyrites; kinetics of flotation process of molybdenite; influence of pulp density; emf (negative milivolts) of pulp and the expenditure of nitrogen on tech-nological indexes of molybdenum flotation. When working in nitrogen medium decrease of NaHS in rougher molybdenum flotation from 40% to 45% is settled. When nitrogen is also fed in cleaner stages, the total expenditure of depressor is lowered by 64%. The quality of end molybdenum con-centrate is raised with over 5%. On the ground of the results of laboratory studies and of world practice data, an industrial installation for selection of copper ? molybdenum concentrate in nitrogen medium in Wemco inert ? gas machines.

Jan 1, 2014

By P. K. Fedotov

Annually at least 5% percent of world power consumption is involved in the process of ore dressing while ore processing technology. Such rate of energy consumption demonstrates the importance of a given process study in the human life-sustaining activity. Examining of interparticle destruction being under external stress pressure in ore responses this problem solution at the greatest degree. The technology of destruction in the roll press is of great interest. The use of the given equipment allows to save a significant amount of energy by means of the built-in ore destruction mechanism. Examination of stress-strain fields which determine the level of interparticle destruction between the rolls in the ore layer enables to specify both level of ore destruction and power consumption. The mathematical computer modeling for the deformable environment use based on the finite-element method (FEM) allows to carry out the given research. We use FEM solution for elastic contact problem for the most complete study of power consumption employed in ore and interparticle destruction. This problem solution allows also to examine energy consumption expenses spent for ore crushing in the roll press. Also we have identified the mechanism of ore in a layer of the particles under pressure roller press. It is established that high level of performance and reduction of energy consumption in interparticle destruction of ore in the layer due to the appearance of the gradient of normal stresses in contact of particles of mineral raw materials. The algorithm has been developed determining crushing product particle size distribution of fractured particles in the layer, using the Bond’s theory of crushing. The use of our FEM model reduces the time of equipment selection for new plant and at the design stage to reduce the risks of errors in the choice of roller presses.

Jan 1, 2018

By Shen Zhengchang

Based on the flotation features of coarse particle mineral, a new type of impeller & stator unit is developed. Particles suspension state generated by this impeller & stator unit under different speeds are tested in laboratory, and critical impeller speed suit for coarse particles flotation is presented. Comparing particle suspension parameters of the new impeller & stator unit with that of KYF impeller and stator unit, it comes up that the distance between the interface of two slurry circulation channels and the cell bottom is larger in the flotation cell with new impeller & stator unit. The test results indicate that the new type of impeller & stator unit is suitable for processing coarse particles due to its good suspension capacity for coarse particles. Keywords: coarse particles, flotation, suspension, critical speed, impeller and stator unit

Sep 1, 2012

By P. M. Solozhenkin

"Galvanochemical process (GChP)) cleaning of sewages is realized in the field of shortcirquited galvanic elements from the mixture current the materials place in purification’s solution and form multitude galvanopairs without external electric field in presence oxygen of the air. The galvanochemical process is electrochemical process utilizing galvanic pairs: coke - iron, iron - copper and others and process does not require chemical reagents.The effect of basic parameters of the cleaning effectiveness have been studied depending on oxidizing of galvanopairs. Adjusting nature, type of galvanic pairs and forming three component system possible to enlarge emf circuits to 2.378 V.The role of ?2, as basic agent, for generation of hydrogen peroxide and hydroxyl ions.It was stated, that removing of metal ions from solutions occur mainly on account of sorption and hydrolytic sedimentation of iron oxihydrates.Determined separate stages of the process: coagulation, sorptions of admixtures on freshly formed ferric oxides and oxidizing destruction of organic components of effluents in presence of ?2 ? ?2?2. Shown efficiency of the method for removing of Cu, Cr, Ni, Zn, As ions, as well as fluoride, phosphate and cyanide anions and oil products, surface-active and flotation reagents. Cleaned water can be recycled for some processes non-critical toward residual concentration of admixtures, as total salt contents is lowered on 60-75 % and reaching limits of concentration for toxic components.The concept of high power unit creation was developed, and galvanochemical pulsator is presented. The pulsator is not expensive, and exploitation expences are low, as well as servise is simple with high effectiveness, and capacity. The galvanoflotation process is developing, combining galvanochemistry and flotation of hydrofobic admixtures (oil, surface-active agents).The galvanochemical flotators are presented."

Jan 1, 2003

By Stephen J. Harker, John Knights, Randolph A. Pax, Glen A. Stewart

"Mineral samples were obtained from different stages of a mineral processing circuit used to extract the copper and gold rich mineralogical phases. The aim of this work is to characterise the quality of the samples at different stages of processing. The samples were taken of the head grade, tailings, cyclone overflow and the final concentrate.Characterisation of the samples was determined using Cu-Ka X-ray powder diffraction and Fe57 Mossbauer spectroscopy. These measurements will be presented and discussed in terms of the enrichment of the ore, showing the removal of magnetite and quartz through the processing, the final concentrate being rich in chalcopyrite and pyrite. This data also shows the utility of Mossbauer spectroscopy to provide mineralogical phase information directly.Mossbauer spectroscopy is a tool to determine the material phases of a sample. It is a nuclear based technique which measures the amount of attenuation of a narrow Doppler shifted source energy as it passes through a sample. The attenuation depends on the amount of resonantly absorbing material in the nuclear radiation path from the source to the detector. Synchronous detection of the doppler shifting velocity and the nuclear radiation count gives a Mossbauer spectrum. By convention, the energy axis of the Mossbauer spectrum is displayed in units of velocity.Figure 1 shows Mossbauer spectra obtained for a sequence of samples throughout a processing plant. These spectra show the removal of magnetite and the concentration of chalcopyrite and pyrite. Optical microscopy results indicated a significant component of bornite not witnessed with Mossbauer spectroscopy. Closer examination showed that optical microscopy assays over estimate the bornite component."

Jan 1, 2003

By Julian Dimitrov, Kremena Dedelyanova

"The paper presents research on hydrodynamic processes occurring at the elementary act of flotation. Discussed existing models to determine the effectiveness of conflict of bubbles with particles in vibration column flotation machine. The paper presents a disperser for a column flotation machine, in which the dispersion of the gas phase is carried out using vertical vibration with defined frequency and amplitude. The paper presents research of mechanism for the creation of air bubbles in vibratory column flotation machine. The factors influencing the increase in the duration of the bubble in the area of contact with the mineral particles are discussed. Research was carried out on the effect of frequency and amplitude of vibrations on speed of precipitation of mineral grains of different density. Formulas are derived for the parameter effect of vibrations, applicable to the design of flotation machine. The collision efficiency of the bubbles in vibratory column flotation machine is determined. The vibrations of the hydrated layer allow for cost-effective implementation of the elementary act of flotation by providing larger relative velocities at the contact point between the bubble and the solid phase. It is proposed to complement the model more accurate representation the mechanism of attachment of the particles to the bubble."

Jan 1, 2014

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By Alan Bye, Nick Beaton, Wayne Stange, Emmy Manlapig, James Groutsch

"For over 50 years the JKMRC has applied a unique education-based research strategy to develop modelling and simulation tools that are "fit for purpose" for industrial application. These tools are widely used for the analysis and optimisation of mining and mineral processing systems. As the mining industry context evolves to deal with declining head grades, falling commodity prices, professional skill shortages, and an exponential growth in the volume of data, a re-evaluation of what "fit for purpose" means in the future is required. It is contended that future industry needs for simulation-based decision support requires tools and systems that incorporate: • Multi-component modelling, • Models of complex sensor behaviour, • Integration across the physical value-chain e.g. resource to market, • Financial analysis including risk and uncertainty assessment, • Enabling multi-criterion decision making (technical, financial and environmental), • Ore-body knowledge at multiple scales, • The use of fundamental numerical models to provide insight for the development of practically useful models, and • Decision support delivered through remote operations centres. JKMRC and CRC-ORE are collaborating to develop a next-generation simulation-based decision support system that assists in addressing these challenges. The Integrated Extraction Simulator (IES) combines many years of pragmatic and successful work integrated with modern technology trends - in particular the rapid move to cloud-based computing."

Jan 1, 2014

By Lei Zhang, Xianjun Lu1, Minjie Lian, Liyang Zheng

In order to investigate rheological behaviour of fine tailings backfill pastes, the fine iron ore tailings (size fraction of -0.074mm accounts for 70%) from Fuquan Mining Co., Ltd. of Sinosteel Corporation (Shandong, China) was investigated. The rheological parameters such as slump, viscosity and yield stress of the tailings pastes under different densities were measured in detail, and the effect of paste density on the rheological property and the relationships of different rheological parameters of the pastes were also discussed. According to the results, the rheological behaviour is in accordance with the pseudoplastic fluid in a wide range of paste densities (solid content, w/w) of 65% to 80% and the pastes turn to be Bingham fluids at higher shearing rates. Along with the increase of paste density, the slump drops gradually and the viscosity and shear stress increase gradually. However, the variation extent of the rheological parameters varies at different density ranges. According to the variation pattern of the rheological parameters at different paste densities, the flow ability of the pastes can be classified into three zones. The high fluidity zone was observed at the density range of 65%-69% where the rheological parameters vary slightly along with the paste density, the moderate fluidity zone was observed at the density range of 70%-76% where the rheological parameters vary significantly along with the paste density, and the low fluidity zone was observed at the density range of more than 76% where the rheological parameters vary sharply along with the paste density and the critical density for this sudden variation is about 76%. Furthermore, linear correlations of slump/viscosity and slump/yield stress were observed. It is possible to predict the viscosity and yield stress of the pastes based on the slump measurements.

Jan 1, 2014

By R. Els Ellis

Enhanced granulation of UASB granules was tested on pilot scale with two different test reactors (about 5 litres capacity each). Sludge from a local sewage works was used, with peach cannery effluent as carbon source. Cyclic motion of the reactor contents, and a daily replenishment of feed material create the necessary stress conditions for enhanced growth. Sizable granules, bigger than 0.5 mm, were produced within 20 days. Of the two reactors tested, the reactor equipped with a horizontal agitation shaft proved more effective.

Jan 1, 2003