Search Documents

By Chuansheng Luo, Qiuyang Hong, Lili Zhang, Dongyun Liang

"The metallogenic rock of a sandstone-type Cu ore is arkose-quartzite as well as siltstone and the cement is composed of argillaceous minerals including sericite, chlorite, etc. and carbonate minerals including calcite, dolomite, etc. A detailed process mineralogy study on this complex copper ore was carried out using MLA combined with traditional research methods. According to the results, there are many types of Cu minerals including copper sulfideminerals, secondary copper sulfideminerals, copper oxideminerals, copper carbonate hydroxide minerals and copper silicate minerals in the ore. Based on the occurrence of Cu, the copper existing as copper sulfide minerals (bornite, chalcopyrite and chalcocite) and copper oxide mineral (malachite) which have a good floatability accounts for 49.28% while the copper (chrysocolla) hard to be recovered by flotation and the copper existing in the cement (sericite, chlorite, psilomelane and limonite) accounts for 48.65%, and the copper existing in the carbonate minerals (calcite and dolomite) accounts for 1.72%. The process mineralogy study indicates that the process "beneficiation combined with hydrometallurgy" should be applied due to the various occurrence of Cu. The abundance of calcite and dolomite is about 12%, so removing these acid-consuming minerals by floatation is an effective way to reduce the acid consumption in the hydrometallurgical process and the lowest Cu loss is 1.72%. So the process "floating copper minerals-floating calcium minerals (calcite and dolomite)-leaching copper from the tailings" is used in the pilot tests. The recovery of floating copper and leaching copper from tailings is 46% and 30% respectively, so the total recovery of copper is 76%. Compared with the original process "leaching copper from crude ore-floating copper from the residue", the total recovery reduces by 1% but the acid consumption of producing per ton of copper decreases from 37t to 12t. The new technology process has a great advantage."

Jan 1, 2014

By M. Evertsson, E. Hulthén

"In aggregate production and mining the operators are responsible for controlling and monitoring the process to maintain high plant throughput and safe operation. Operators have to make different decisions to control the process due to changed demand on the operation from both management and conditions of the process. The quality of the response and the time it takes for an operator to respond to altered demand relies on what information is available and the experience of the operator. In this work a dynamic simulation platform has been developed to be used for operator training. Models for representing production units and process control for plant simulations have been developed and implemented in MATLAB/SIMULINK to simulate time-dependent plant behavior. Stochastic and scheduled events are included using the discrete events simulation toolbox SimEvents. The human-machine interface was developed using the human-machine interface software ICONICS. The operators’ cognitive process, in interpreting the plants semantic, has been studied by observations and with informal interviews with operators. This was done to get information about the daily operation and the problems that occur in the process. By interacting with operators that experience different physical interactions with the process; more qualitative e-learning software for supporting operator training in a dynamic operator environment could be developed. The quality of the operator training environment was evaluated with a usability study that was performed with operators and others within the production."

Jan 1, 2014

By Shankar Narasimhan

Data Reconciliation is a technique that has been developed more than fifty years ago and has been refined over the past few decades and is now being deployed routinely in several process industries such as refining, petrochemicals, mineral processing and hydro-metallurgy. The main aim of data reconciliation is to obtain accurate estimates of all process variables and parameters using plant measurements that are invariably corrupted by random errors and may also contain biases and other gross errors. These reconciled estimates are subsequently used either in offline exercises such as simulation, retrofitting, and de-bottlenecking or in online optimization and control applications. In this presentation, a brief history of data reconciliation, its assumptions, and uses are reviewed. New developments in this area are highlighted such as robust data reconciliation to handle model uncertainties, and reconciliation using identified models derived purely from operating data. Several case studies in the mineral processing industries reported in the literature are also highlighted to indicate the potential benefits of this technique.

Sep 1, 2012

By S. Martins

The aim of this work is to compare three different results of charge motion in a modified 5ft diameter lab mill and to identify differences and similarities in these results. The lab mill is modified from tumbling a ball charge to tumbling a charge of disks. This modification replicates 2D motion. This 2D condition is measured using an instrumented disk (iDisk) and analysed using a video imaging system. The iDisk is equipped with a 3D accelerometer array and rotation rate sensors. With the help of a video system, some measured quantities are also determined externally. The results of these three predictions or measurements are presented. A discussion is included.

Jan 1, 2014

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Häkkinen Antti, Salmimies Riina, Matveinen Maria

"Tailings generated during the upgrading of ore present a major challenge for the mineral processing industry. On one hand, the processing of tailings requires added capital input. On the other hand, increased difficulties in obtaining permits for dams and landfilling and increased costs associated with storage and tailings management also result in increased costs. To promote sustainability and make tailings management economical, added value must be generated from the waste material. This might be possible through the recovery of the metal values in the waste. This work discusses the possibilities of recovering metals from multimetal tailings through leaching in a stirred tank. The characteristics of the tailings are crucial and the distribution of the metals within the different size fractions is used to identify the most attractive route for the hydrometallurgical step. Leaching of nickel and copper is further investigated using acids at different concentrations. The leaching of base metals is possible at acidic conditions. Increased temperature and concentration of the leaching agent promote the dissolution of the metals, as could be expected. With simultaneous dissolution of several metals the dissolution mechanisms are difficult to identify. Furthermore, as several metals, not all of them being target elements, are leached another challenge arises from the selective recovery of those metals from the liquid phase."

Jan 1, 2014

By Yuki Tsunazawa, Shuji Owada, Kazuki Tahara, Shinobu Ogino, Chiharu Tokoro

"Printed circuit boards (PCBs) are an important constituent of waste electric and electronic equipment (WEEE), and contain many electronic components with valuable, hazardous or both materials. Recycling of PCBs is an important subject not only from the treatment of waste but also from the recovery of valuable materials. Demand for rare earth metals is expected to accelerate because of their growing use in next generation high technologies. Since some of these metals are concentrated in a specific electronic component, for example, Ta in capacitors, a special and selective grinding such as parts detachment from the board is effective for the recycling of a part of rare metals. However, direct computer simulation method to investigate a comminution/detachment process of PCBs has not yet been established. In this study, our objective was revealing the mechanism of breakage phenomena in comminution / detachment process of PCBs using computer simulation. A special and selective grinding using an agitation mill promoted the removal of components from a PCB by detachment and was an effective method for the recovery of rare metals. Simulant PCBs on which some capacitors were solder-mounted were used for the comminution test using drum type mill with agitator. To describe this mechanism of the parts detachment process, a computer simulation using discrete element method (DEM) was conducted. Although only an indirect simulation using the spherical particle model was possible for part detachment and board breakage, the particle-based rigid body model could directly represent the behaviour of PCBs. Simulation results successfully corresponded to comminution experimental results."

Jan 1, 2014

By Bruno Miotto, Rômulo Faria, Juliano Tessinari

Water has become a scarce resource in quality. Companies in the ornamental stones sector use water intensively in their processes. Given the current situation, it is imperative to rationalize this feature that at first is related to the reduction of consumption, through no waste. Considering the importance of environmental preservation of this resource and also to comply with the legislation that governs the procedure for processing of ornamental stones, new alternatives should be available for the maintenance of current activities and promoting the development / growth of the sector on the principles of environmental sustainability and economic in future scenarios. The ornamental stones processing industries, especially for micro and small enterprises, require the implementation of a management program that optimizes the use of this feature, since the techniques individually processed operate with three basic processes dependent on water use: split blocks, polishing and finishing slabs. This technology requires a large volume of water resources and control measures involving operating recirculation water can minimize power consumption, making the company more profitable and sustainable. This is a survey of literature, associated with technical reports provided by partner companies and government agencies. This study aimed to the organization and provision of theoretical knowledge about the subject matter coupled with management practices, which may be reproduced or re-purposed in ornamental stones processing companies. It should be noted that the industry in question is lacking in technical expertise for the implementation of sustainable attitudes relevant to water reuse.

Jan 1, 2014

By Rebecca Hope, Derick Moolman, Frikkie Malan

"Despite the lip service that has been paid to pro-active plant maintenance processes over recent years, a significant portion of maintenance in industry is still reactive. The business driving force to prevent expensive production opportunity costs arising from “break-down maintenance” is obvious. Various benefits can be derived from successfully deploying remote equipment diagnosis technology and associated business processes.From an end-client’s viewpoint these include the ability to predict and take actions to prevent equipment breakdowns, increasing the lifetime of equipment by responding to appropriate operating instructions and therefore improving the return on capital expenditure. Better planning and scheduling of maintenance priorities and resources with performance measures like an Equipment Health Index are also possible. The knowledge that a qualified supplier engineer is constantly in touch with the operating conditions of their equipment, albeit remotely, is more than a comfort, and can be translated into quantifiable cost savings and improved supplier service levels.This paper analyses the reasons for the inadequate level of pro-active plant maintenance practice in industry today, and presents a number of important criteria in selecting appropriate solutions to this problem. A case study of a specific real-time, remote equipment management application is presented."

Jan 1, 2003

By Megan Becker, Cyril O’Connor, Jenny Wiese, Gaynor Yorath

The effect of particle shape on true flotation has been widely reported. The present paper presents results obtained in investigating the effect of particle shape on the entrainment of particles during the flotation process. Different hydrophilic minerals with particles of varying aspect ratios were used and their shape determined using rheological tests and QEMSCAN. Their entrainment properties showed a close relationship to their shape with the recovery due to entrainment increasing as the aspect ratio of the particles increased. The effect of surface charge, by changing pH, and size of particles showed that the effect of shape was sustained at different pHs and particle sizes. Proposals are made to explain these observations in terms of the known relationships between drag coefficients and terminal velocities and shape. Since it has been previously reported that different milling procedures can affect particle shape, these results indicate that it is possible that such different procedures may result in increased entrainment of hydrophilic minerals.

Jan 1, 2014

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture.In particular Davy derived an equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. Furthermore, this covariance can also be used to measure the variance of the composition distribution of each mineral.This paper shall present results verifying this equation. The experimental method was based on obtaining particle information from serially-sectioned particles. Particle samples selected for serial sectioning displayed a range of natural textures including liberated, binary and composite particles. The exposed surface of the polished sections were analysed using QEM*SEM. This procedure was repeated until all of the grains have been polished away. The covariance of mineral distributions were calculated from the serial sections and compared with that calculated using Davy’s equation."

Jan 1, 2003

By R. Imhof, S. E. Sánchez-Pino, H. Sprenger, S. A. Sánchez-Baquedano

"In 1992, Ingeniería de Minerales started with the introduction of pneumatic flotation technology in Chile and South America. This technology consists of vertical cells and gyratory cells, used mainly under actual operational conditions, with pilot units directly installed in the concentrator circuits of the industrial process. Successful industrial applications have been observed at Los Pelambres, in the molybdenum plant; at Codelco Andina in the molybdenum plant as pre-rougher to produce directly a final concentrate; in the copper circuit at Las Luces as pre-rougher producing final concentrate using sea water; at Minera Valle Aconcagua where a full automatic plant produces pre-concentrate from fresh tailings as feed; at the silica and silicate reverse flotation circuit of Compañía Minera del Pacífico; in cleaning the final concentrate of Zn by reverse flotation removing ultrafine carbonate; and in a plant that reprocesses fresh tailings from a copper slag flotation process. Positive operational changes in the design of the flotation circuit have been seen in plants using G-cells and V-cells, improving the performance of flotation circuits and the quality of final products. The high concentration of bubbles and micro turbulence produced by the pneumatic aeration units provide a high probability of collision and attachment, reducing dramatically the residence time. Though it is a pneumatic flotation, no compressed air is needed, and the equipment is characterized by low maintenance costs, full automation, savings in investment and energy."

Jan 1, 2014

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By Kyle P. Flynn, Frank J. Hrach, James D. Bittner

ST Equipment & Technology, LLC (STET) has developed a processing system based on tribo-electrostatic belt separation that provides the mineral processing industry a means to beneficiate fine materials with an entirely dry technology. In contrast to other electrostatic separation processes that are typically limited to particles greater than 75µm in size, the triboelectric belt separator is ideally suited for separation of very fine (<1µm) to moderately coarse (300µm) particles with very high throughput. The high efficiency multi-stage separation through internal charging/recharging and recycle results in far superior separations that can be achieved with a conventional single-stage free-fall tribo-electrostatic separator. The triboelectric belt separator technology has been used to separate a wide range of materials including mixtures of glassy aluminosilicates/carbon, calcite/quartz, talc/magnesite, and barite/quartz. An economic comparison of using the tribo-electrostatic belt separation versus conventional flotation for barite / quartz separation illustrates the advantages of dry processing for minerals.

Jan 1, 2014

By A. V. Bauman

"Important for thickening processes is the ability of slurries to form under certain conditions aggregation and sedimentation stable systems. Substantial part of difficult to sediment solid particles in such systems may be in colloidal state. The technique to study the sedimentation and aggregative stability of the slurry developed by the author with co-authors makes possible to define kinetics of changes in the aggregative stability of the system with solid phase varying concentration in it and produce data on sedimentation stability of the system in preliminary investigation of the thickening process. Research of aggregative and sedimentation stability of the slurry complement standard methods of laboratory studies to prevent errors in development of water-slime thickening balance and water circulation to design new and upgrade existing processing plants. Statistical analysis of process audits of more than one hundred upgraded and newly commissioned processing plants carried out in recent fifteen years showed that more than two-thirds of problems arising in commissioning the processing plants are associated with misdesign and errors in thickening and water circulation system. Among the main reasons of process design failures are: non-conformity of actual characteristics of the raw material to design characteristics, low quality of preliminary studies at the stage of sedimentation process simulation, design failures, wrongly selected equipment for the thickening and water circulations systems. As of today a number of problems associated with laboratory studies of sedimentation process, first of all, with interpretation of precipitation curves produced at the stage of laboratory refinement of the thickening process have been pinpointed. (Bauman A.V. Outstanding issues in design of thickening and water circulation diagrams in processing plants // Ore processing. 2016. ?3 P. 58-62) ?????? ?.?. ?????????? ??????? ?????????????? ???? ???????? ? ??????????? ?????????????? ??????. // ?????????? ???. 2016. ?3. ?. 58-62))"

Jan 1, 2018

By M. Ito

The authors have developed the RETAC jig (a modified TACUB jig) and have reported that the RETAC jig can separate relatively low density particles such as plastics. To further improve the separation ability, a hybrid jig (a RETAC jig with an air bubbler under the particle bed), which can separate plastics having similar specific gravities by the differences in the wettabilities of the particles was developed. Surface modification of plastics with similar wettability enabling separation in the hybrid jig and the effects of wettability control of the plastics using reagents are reported.

Sep 1, 2012

By Muammer Kaya, Sait Kursunoglu

"Energy is the major concern for society. It is expected that developing country economies and populations will grow and consume more energy. Interest in nuclear power is rising, while the world looks for non-depletable energy source that will not contribute to global warming. However, it still has concerns of nuclear proliferation, radioactive waste and safety. It is necessary to overcome these concerns if nuclear energy is expanded to developing countries. Thorium (Th) utilization as nuclear fuel will be an opening key of these difficulties because Th produces less Plutonium (Pu) and less radioactive waste with enhanced safety. Research into the use of Th as a nuclear fuel has been taking place over forty years, through with much less intensity than that for uranium (U) or U-Pu fuels. Nuclear industry is currently using only 0.7% of the available energy from mined U. With huge resources of Th and relatively little U, Turkey has made utilization of Th for large-scale energy production a major goal in its nuclear power programme. Thorium fuel is plentiful and inexpensive. Energy is major concern for developing Turkish society. Turkey, today exports more than 70% of its energy as fossil fuels. In the last 50 years, Turks are skeptical, anxious and indecisive about having nuclear energy for electricity production. In the last 10 years, Thorium is brought into Turkish government’s attention and national discussion as a new, safe, clean, affordable, CO2-free, alternative, strategic and domestic nuclear energy fuel. Turkey recently contacted four VVER-1200 type Russian Nuclear Power Reactors using U as a fuel in Akkuyu (Rosatom) and another four units will be established in Sinop in the next decade by Japan (Mitsubishi-Westinghouse). Turkish nuclear programme must envisage use of domestic Th as a fertile material. This paper briefly reviews the developments of Th-fuel cycle for nuclear energy from global and Turkish perspectives. Previous Th reserve development and recovery studies from Turkish bastnasite ore are summarized in this paper."

Jan 1, 2014