Search Documents

By Joseph A. Mann

"Soil mixing is a proven solution for the construction of ground improvement adjacent to sensitive structures due to the use of computer controlled and monitored equipment. The precision to which geometry is controlled can often be the deciding factor for selection of soil mixing versus other means of ground improvement. Protection of existing structures and utilities requires careful planning, investigation, and may demand supplemental control measures. During planning, it is imperative that the process be fully developed by the project team to ensure proper control measures are budgeted; otherwise, the success and safety of a project can be jeopardized.This paper discusses case histories of soil mixing performed in close proximity to large, sensitive, and critical utilities, including foundation support for an existing earthen dam impounding a water reservoir in upstate NY, a buffer zone for a tunnel drop shaft at an operating wastewater treatment plant in Washington DC, and a containment system to protect a major water line along an interstate widening project in Baltimore, MD. The function of soil mixing as ground improvement varied; however, the selection and application of the technique versus other means of ground improvement was specific due to the controlled manner of construction with soil mixing. Through the three case studies, small diameter (3- ft [0.9 m]), large diameter (8-ft [2.4 m]), and mass mixing applications will be discussed. Furthermore, the case studies offer insight into how the geotechnical community in the Mid-Atlantic utilizes soil mixing technology for widely varying applications. Additional topics of discussion will be the design and construction of the ground improvement systems, procedures and execution of the work to protect existing structures, and the QA/QC methods, procedures, and results from the projects.INTRODUCTIONWet soil mixing, also known as the Deep Mixing Method, is a ground improvement technique that improves the characteristics of weak soils by mechanically mixing them with cementitious binder slurry. To construct columns, a powerful drill advances a mixing tool with radial mixing paddles located near the bottom of the drill string. The binder slurry is pumped through the drill string to the tool as it advances and additional soil mixing is achieved as the tool is withdrawn.Wet soil mixing is applicable in a wide range of soils. Soil mixing has been performed at depths more than 100 lf (30 m). Soils vary widely in their ability to be mixed, depending on the soil type, strength, water content, plasticity, stratigraphy, and texture. Almost any soil type, including organics, can be treated with certain soil mixing technologies, although they may require high binder contents and/or pretreatment to achieve the required results. In cases when the target soil is very soft, including some very weak clays and peats, 100% of the soil may require treatment. This complete coverage of soil mixing is referred to as mass mixing."

Jan 1, 2015

By Shields H. Arup

The paper describes the innovative foundation reuse and strengthening works for two buildings in Central London. A 1950s building on piled foundations (65 Whitfield St) and a 1930s building (67-69 Whitfield St) on 3m deep pad foundations were both extended upwards by two new stories. The Client for the project is Derwent London, with Make as their architect, Main Contractor Multiplex and Engineer Arup. Little was known about the foundations of either building at the start of the scheme. Extensive investigations of the existing foundations and ground conditions were carried out in both buildings. At 65 Whitfield St, investigations identified piled foundations, but found that pile lengths were short and variable. As a result, strengthening works solutions were adopted whereby the increase in column load was shed into new mini piles constructed around the existing pile caps. At 67-69 Whitfield St, deep pits were used to investigate the foundations and reuse was justified based on understanding of the pad dimensions, concrete strength, and strength and stiffness of the underlying geology. For both buildings the residual risk was closed out through monitoring during construction. The combined reuse of the structural frame and foundations of both buildings facilitated a sustainable solution, breathing a new lease of life into outdated buildings.

May 1, 2022

By Henry H. Tayler, Eric Sturel

1 Triton Square was originally a six-storey building with a one-level basement located within a commercial development near Euston, London. It was designed and constructed in the 1990s and the foundation scheme comprised straight shafted London Clay piles arranged singly beneath columns. The scheme added three storeys and a five-storey infill in the central atrium area to increase the building floorplate by 70% and maintained the usability of the basement space. As the loads to support the additional floorplate area were greater than the capacity of the existing foundations, an optimised strengthening scheme of small diameter piles installed within the existing basement and a slender retro-fitted raft was installed to augment the existing piles. The re-use and strengthening of almost all of the existing foundations enabled re-use of a very high proportion of the superstructure and in approximately 35,000 tonnes of concrete and 1,900 tonnes of reinforcement and structural steelwork being re-used. The structural embodied carbon for the refurbished building scheme is estimated at an average of 136 kgCO2e/m2, achieving a Structural Carbon Rating Scheme (SCORS) “A” rating with components detailed in the paper.

May 1, 2022

By Maurizio Siepi, Paul van Horn, John Coupland, Julian Crawley

"TTMJ is the acronym for the Slurry (Diaphragm) Wall Tension Track Milled Joint currently in development as part of the European Union's innovative and far-reaching Horizon 2020 initiative (FTI Pilot-2015-1 720579). The TTMJ Project has been specifically set up to deliver this versatile new step-forward in Slurry Wall technology. The TTMJ System is protected by patent in Europe and the USA, and is currently under development by a consortium comprising Trevi SpA (Italy), Arup (Netherlands) and CCMJ Systems (UK). The principles of the TTMJ System together with the installation process are herein described in general terms. The system is still under development with field trials scheduled for early 2018, so some of the detail will not be disclosed at this stage. It is the intention of the Authors that the results of these field trials and a more complete description of the System will be presented in a paper we intend to submit for the DFI/EFFC International Conference on Deep Foundations and Ground Improvement to be held in Rome, Italy in June 2018. The final section of this paper explains how the TTMJ system can be applied to a common application of slurry wall construction; deep circular or multi-cell shafts. The system can be used to construct shafts more easily and at less cost than current methods. It also allows shafts with smaller internal dimensions to be constructed than is currently practical.INTRODUCTIONCCMJ Systems (UK) realised that an innovative new approach to forming joints in both Slurry (Diaphragm) Walls and Secant Pile Walls would provide greatly improved joint integrity to greater depths, to the overallbenefit of retaining wall quality, across the world-wide foundations industry.In particular this new system is designed to:??Increase the effective depth range of Slurry Walls (especially walls excavated by grab) and Secant Walls??Remove the requirement for Stop-ends or Joint Formers??Allow for a Shear Key at the joint??Allow for a Water Stop to be installed at the joint??Permit Continuous Reinforcement across the joint??Optimise Reinforcement Density and hence Concrete Flow??Facilitate joints in corner panels eliminating the need for “L” shaped cages and reducing largesingle-pour concrete volumes and slurry storage capacity requirements.??Enable the construction of smaller-dimensioned square and circular deep shafts (especially useful for city-centre sites) than is possible with current methods.CCMJ Systems approached other industry specialists with a view to forming a development team to explore the possibilities for this new technique."

Jan 1, 2017

By Caciola Jr. Joseph J., Nidal M. AbiSaab

"Thanks in great part to the geology of the New York City Metropolitan area, mini-caissons are a popular choice for deep foundations. These drilled elements are readily available, easy to install with minimal impact on adjacent structures, and can be designed with large compressive and tensile capacities. Despite the frequency with which they are employed, the engineering design community is divided over several of the underlying principles governing the design of mini-caissons. This paper seeks to draw attention to several of these issues in an effort to encourage further research and discussion, namely: (1) how the allowable stresses have changed for the NYC Building Code over time, (2) the inconsistent load transfer mechanisms considered for geotechnical capacity, and (3) the role of the permanent steel casing towards structural capacities of mini-caissons.INTRODUCTIONIn the local construction nomenclature, mini-caissons are drilled deep foundation elements which derive their capacity from a socket in rock. A permanent steel casing (commonly between 7- and 24-inches in diameter) aides the drilling through overburden soils to the top of bedrock. Afterwards, an uncased rock socket is drilled into the bedrock and the inside of the casing and rock socket is inspected by means of portable video equipment. After inspection, the interior of the socket and casing is filled with steel reinforcement and concrete or grout. The casing-soil interface is generally ignored for axial design purposes and the full geotechnical compressive or tensile capacity is assumed to be generated in the rock socket. Figure 1 shows a typical mini-caisson cross section.Mini-caissons have been used for decades in the New York City area for a number of reasons. They have historically been proven to develop high axial capacities in the city’s metamorphic rock (Tamaro et. al. 2000), often exceeding 300- to 500-tons. Additionally, their method of installation (drilling) is generally able to bypass layers of dense Glacial Till, boulders, and manmade fill which would interfere with the installation of other pile types (e.g. driven piles, auger cast piles). Further they are able to extend to depths exceeding 50-ft to reach bedrock underlying a site, making them a useful tool in areas where rock is relatively deep or varied in elevation. Drilled casing installation also results in fewer vibrations and disturbances to adjacent structures and can occur in areas of restricted access (a constant concern for any project in a dense urban environment such as NYC)."

Jan 1, 2016

By Stuart Hardy, Xiangbo Qiu

The South Bank Place project comprised the redevelopment of the iconic Shell Corporation headquarters in Waterloo, located on the Southbank of the River Thames in central London. The site was originally developed in the 1950’s and due to the monitoring of the underlying Bakerloo Line tunnels by the Building Research Station it has become a seminal case history for the long term swelling behaviour of London Clay. The redevelopment, undertaken by a joint venture of Canary Wharf Group and Qatari Diar, included demolition of the existing building (with the exception of the main towers) retention of the existing basement structure and the construction of eight new mixed use buildings, up to 31 storeys in height. The foundations for the new buildings varied according to the building height and the below ground constraints. Two of the buildings are partially founded in reused under reamed piles that were installed as part of the original 1950’s development. The paper describes the novel methodology developed to assess the re-use of the under reamed piles which builds on the guidance published by CIRIA and the BRE for straight shafted piles. The paper also describes the physical investigations and numerical analyses undertaken as part of the assurance process and the procurement of latent defect insurance by the client.

May 1, 2022

By Paul C. Schmall, Kevin Clarke, Paul J. Lewis, John M. Stanbury

"The $200M rehabilitation of the more than 100-year-old Gowanus Flushing Tunnel and pumping station located on the Gowanus Canal in Brooklyn, NY required deep excavations in an extremely congested urban environment. The environment posed significant challenges, including: support of excavation for protection of existing structures, excavation through man-made fill while eliminating groundwater inflow due to potentially contaminated groundwater chemistry; discharge and disposal impacts; and potential settlement of surrounding structures. This paper will present the design and construction challenges associated with the construction of a new combined sewer overflow (CSO) chamberwhich included a jet grout bottom seal, to mitigate groundwater inflow during excavation. The foundation for the finished structure also included a unique system incorporating the jet grout bottom seal elements with deep jet grout columns (piles) acting as the foundation system for the final structure. Design and construction challenges included highly variable soil conditions such as man-made fill, obstructions from previous construction, presence of an organic stratum, and conflicts with existing timber foundation piles. The jet grout bottom seal was constructed in loose sands with the deeper jet grout foundation elements extending to bear on a dense sand stratum. Challenges associated with the bottom seal included grid spacing and construction sequencing. Wet in wet sequencing was used to mitigate potential windows in the bottom seal further complicated by shadowing from existing timber foundation piles.Introduction And BackgroundModernization of the Gowanus Tunnel Pumping System required deep excavations in the extremely congested urban environment of Brooklyn, NY. The project location is shown on Fig. 1 and 2. The focus of this paper is to present the design and construction challenges associated with the support of excavation, control of groundwater, and ultimate foundation support for the combined sewer overflow (CSO) bypass chamber extension. The project site was tightly constrained by adjacent, active roadways and underground utilities, as well as residential and industrial structures. Therefore, excavation support was required to limit ground movement and maintain the integrity of the surrounding facilities. Excavation depths to as much as 16 ft below ground level, 8 ft below groundwater, required that seepage and groundwater be controlled so as to minimize pumping and disposal of groundwater and maintain the surrounding groundwater levels to avoid potential settlement of adjacent roadways, utilities, and structures. In addition, the subsurface conditions required that the proposed CSO bypass chamber extension be supported on a deep foundation to avoid differential and total settlements that may be detrimental to the existing and expanded structure. A plan view of the existing CSO bypass chamber and the proposed extension is shown on Fig. 3."

Jan 1, 2016

By Timothy Nelson, Simon Burnworth

"The University of California’s new Berkeley Art Museum and Pacific Film Archive will showcase a collection of art and film in a facility that pairs an existing 1930s-era printing press facility with a new, architecturally unique auditorium wing. The centerpiece of this adaptive-reuse project is the existing 3- story art-deco Administrative Building, which will be integrated into the new museum and provide approximately 18,000 square feet of usable space. Degenkolb Engineers, as the shoring engineer of record, along with Condon Johnson & Associates Inc., the shoring contractor, worked together with general contractor Plant Construction Company to design and build a temporary structure to facilitate the complex retrofit, renovation, and expansion of the Admin Building. This paper will discuss the challenges faced by the design and construction team, the sustainable solutions implemented on the project, and the collaboration between teams to meet the unique constraints of the project and the site.INTRODUCTION AND PROJECT BACKGROUNDThe Berkeley Art Museum and Pacific Film Archive (BAMPFA), which currently resides in a 1970s-era post-modern concrete structure just south of the University of California Berkeley (UCB) campus, was in need of a new home after an engineering evaluation revealed that the building possessed seismic deficiencies. Pressed for space, the University looked within its portfolio of properties and identified the site of the former University Printing Press facility as the place to build BAMPFA’s new home."

Jan 1, 2017

By Steffen Schweizer, Tadeusz Brzozowski, Alfred Koller, Michał Topolnicki, Jürgen Wäger, Grzegorz Sołtys

A full scale test has been conducted to determine ground bearing pressure under rig tracks. The track loads were recorded in real time using Liebherr's Ground Pressure Visualisation system, and the vertical stress induced in the ground was measured with pressure cells embedded in the ground. It has been found that the recommendation of EN 16228 regarding determination of the track length is oversimplified. The contact length should dependent on the susceptibility of the working platform. It has been also demonstrated that the corrected pressure distributions under the tracks influence the dimensioning of the working platforms. As a result, the designed working platform may actually be less secure than is shown by conventional calculations.

May 1, 2022

By Abid Adekunte

"In recent years, developers have had to deal with complexities associated with numerous cases of deep basement construction in built-up areas. Design and construction of deep excavation support systems in urbanised zones come with many technical challenges. Restricted working spaces often render the use of temporary struts as wall restraint systems unpopular, as working space needs to be maximised. Also, tie-back anchors are often inapplicable due to the existence of adjacent structures. Therefore, developing alternative restraint systems for deep basement structures in builtup areas is becoming increasingly important to the present day basement engineer.This paper is centred on the design, construction and monitoring of enabling works for deep basement structures on three sites in the United Kingdom and Republic of Ireland. Traditional tieback anchorage and propping systems were inapplicable on the sites. As alternatives, separate novel wall restraint systems were developed and adopted, to enable excavation on each of the three sites.Performances of the novel wall restraint systems, as well as the responses of adjacent structures were monitored. Numerical modelling and field monitoring results show the three alternative wall restraint systems to be safe and effective. The paper also highlights the advantages of the novel solutions over conventional methods.INTRODUCTIONRecently, deep basement structures have become popular components of urban building developments. As pointed out by Pearlman et al., 2004, this could be attributed to the inadequacy of surface parking spaces in urbanised zones, while underground parking facilities are also believed to improve both aesthetic and commercial qualities of urban structures.However, while the incorporation of basement structure into new urban development appeals to developers and architects, the engineering design and construction aspects of basement works typically come against a whole lot of complexities and challenges. As highlighted by Wong, 2002, engineering problems associated with basement construction in built-up areas are numerous, some of these include; complicated sub-soil conditions, dealing with excessive active pressures, complex temporary works, proximity of sensitive adjacent structures, high level hazards to construction workmen and surrounding community, inadequate working space, etc."

Jan 1, 2015

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By Chetan D. Savani, Mike K. Muchard

The necessity to evaluate undocumented foundation lengths is essential in assessing the useable life, need for scour protection, retrofitting, or full reuse of existing bridge foundations. For this purpose, Parallel Seismic Testing (PST) has the best accuracy and is applicable to the widest range of foundation configurations used in bridge construction of any test method. Although not limited to bridges, PST case studies are presented involving two bridges. To preface the case study discussions, an overview of the PST method is given along with its results and analysis thereof. In one of the cases, we were afforded the rare opportunity to see the existing piles being extracted long after the PST testing program was completed. The resulting Class A prediction reaffirms the accuracy of the method. Versatility of the PST method is also exemplified in the two cases presented, where unique situations from complex foundation systems were overcome by analysis to provide successful results.

By Tai Luu, Michael McNicholas, James C. McIntyre

The Jersey City Municipal Utilities Authority (JCMUA), discovered that an existing sewer pipe had collapsed under the New Jersey Transit Conrail Railroad between Pine Street and Ash Street in Jersey City New Jersey. Immediate action was taken to abandon the pipe in place and install a new sanitary sewer. The borings showed 10-20 ft (3.04 m.- 6.09 m) of competent fill overlaying approximately 8 ft. (2.44 m.) of compressible peat and organics. Groundwater was at 8 ft (2.44 m) below ground level. The poor condition of the soils at subgrade could not withstand the extreme weight of the jacking machine or the thrust force required to push the casing from the launching pit to receiving pit. The support of excavation (SOE) would therefore not only need to retain the soil to allow the jacking equipment to reach subgrade at 14 ft (4.27m) below working grade, but also the back wall of the SOE would need to be sufficiently robust to function as the reaction block for jacking operations. The alignment and allowable tolerance for the jacked casing was minimal, therefore the performance of the SOE was extremely critical to the success of jacking operations. This paper will discuss in detail the design concepts that were developed and implemented by the team to overcome these obstacles. HISTORY The discovery of a collapsed section of an existing sanitary sewer led the Jersey City Municipal Utilities Authority to act on an emergency contract. The project design team was tasked with developing an abandonment plan for the broken pipe and installation of the new pipe through challenging geology. The new 180 ft.(54.96 m) long, 54-in. (1.37 m) . diameter sewer pipe was designed to be contained within a 72-in. (1.83 m) protective steel casing. The installation of the new sewer pipe would require a detailed understanding of the geology. The geotechnical subcontractor assembled a subsurface investigation report on November 2nd, 2017. It was quickly realized that the only way to replace the pipe was with a jacked pipe system since the large grade change and the Conrail Right of Way created no other alternative. Delaying or closing the railway was absolutely not an option as that particular railway served as the main heavy-haul route to and from Jersey City. It became apparent that a major obstacle to pipe jacking was the challenging geology present across and beneath the proposed sanitary sewer. The following challenges faced the design team prior to the installation of the replacement pipe:

Jan 1, 2019

By James W. Niehoff

"Prior to 2003, most high rise structures in Honolulu, Hawaii were supported on driven pile foundations, extending through shallow coral strata and bearing in competent formations at depths of 100 ft (30 m) or greater. In 2003, the 40-story Hokua Tower became the first building in Hawaii to use continuous flight auger (CFA) piles for support. These piles derived most of their capacity from side shear in the shallow coral formations, which reduced their required lengths to less than 100 ft (30 m) sand significantly increased their capacity. Not only did CFA piles prove to be more efficient and cost-effective than driven piles, but the reduced noise and vibration associated with their installation made them and drilled piers the foundations of choice for most mid- to high-rise projects going forward. Because drilled foundations were new to Hawaii, it was necessary to develop effective design parameters for the unique soil and rock conditions found within this urban area. While drilled foundations were found to have many advantages over driven piles, construction techniques had to be modified to compensate for extensive voids in the coral formations. This paper presents a compendium of the data derived from numerous full scale, instrumented load tests conducted during the past decade and provides guidance for the design and installation of CFA and drilled pier foundation systems in areas having geologic settings and history similar to that of Honolulu.INTRODUCTIONThe State of Hawaii is one of the most remote areas in the world, lying nearly 2400 miles (3800 km) from the nearest continental land mass. In spite of this vast distance, the population of the islands has grown to over 1 million people, the majority of whom live within and in close proximity to the City of Honolulu on the Island of Oahu. The city is densely populated with over 400 high rise apartments, condominiums, hotels and office buildings located within 5 miles (8 km) of the city center (Fig.1). Nearly all of these buildings have been constructed within the past 50 years."

Jan 1, 2016

By Brandon T. Buschmeier, Sonia S. Swift, Michael P. Walker, Frederic Masse

"Ground improvement has undoubtedly become a cost-efficient and effective solution to support the development of poor soil sites. Ground improvement elements, such as Controlled Modulus Columns (CMCs), replace piles by improving the subsurface soils and reducing settlement. As ground improvement becomes more popular, the applications become more creative and ground improvement is being used to control settlements under large structures with tight settlement tolerances.In this paper, we will discuss the use of CMCs to support two (2) large industrial warehouses where soil conditions would normally lead to the use of deep foundations and a structural slab, grade beams, and hung utilities to prevent excess settlement. Each of the sites we will discuss had poor soil conditions in the form of very soft or compressible soil, heterogeneous fill of varying thickness, and environmental contamination. At each site, we developed a design that would allow for the use of Controlled Modulus Columns (CMCs) with a Load Transfer Platform (LTP) in place of the previously-proposed deep foundations. The use of the CMCs also allowed for the use of spread footings and slab on grade construction. The benefits of this value-engineering approach include economy in the foundation system, risk mitigation by not disturbing contaminated soils requiring expensive removal, and ease of access for future sub-slab upgrades with new tenants. Additionally, the use of recycled concrete aggregate as an LTP is more environmentally friendly than placing structural slabs with heavy steel reinforcement.Designing for the settlement of large warehouses is challenging because it requires changing how we typically perform our designs. For most structures, the slab loads are relatively light when compared to the footing loads, whereas for warehouses, the slab is heavily loaded compared to the relatively light footing loads. Thus, it becomes essential to perform three-dimensional analyses to confirm that the proposed CMC layout will provide uniform support of the slab and footing across a variety of loading scenarios (loaded bays vs unloaded or travel bays). The complexity of the designs for these warehouses generated interest in conducting large area load tests over a grid of multiple columns. The performance of the area load tests provided invaluable information on the effectiveness of the LTP and CMC spacing. In this paper, we present a general description of CMC ground improvement, the differences between ground improvement and traditional pile foundations, our typical design methodology for CMC design, and the modifications to that methodology for warehouses."

Jan 1, 2017

By Eric S. Lindquist

Two microtunnel access shafts were constructed using the Cutter Soil Mixing (CSM) method in the San Joaquin Delta region of California, east of San Francisco. Unlike conventional slurry walls and diaphragm walls that utilize concrete, soil mixing relies on blending the soils in situ with a cement slurry to create a soil-cement wall. Cutter Soil Mixing technology utilizes two sets of vertically mounted cutting wheels rotating about a horizontal axis to produce rectangular panels of treated soil. Overlapping of the soil mixed panels enabled the construction of two circular shafts. CSM panels were constructed to a depth of 29 m (95 ft) for the microtunnel jacking shaft and to a depth of 19 m (63 ft) for the microtunnel receiving shaft. The site presented several challenges, including the high depth of treatment, the variable nature of the alluvial soils, and the high water table. This paper describes the CSM technique and presents the design, construction, quality control measures and advantages of using this method for this project.

Jan 1, 2010

By Tian Miaomiao, Cheng Yin, Shen Jun, Yu Hao, Li Yafei

Vast amounts of waste drilling mud containing heavy metals is produced during oil drilling process, which causes great pollution to the environment. Therefore, it needs to be treated until it is harmless. This study uses industrial waste and Portland Cement stabilized waste drilling mud; the unconfined compression strength, leaching amount of Pb2+ and Cr6+ ions, and pore size of the stabilized soil were tested at different times during freezing-thawing cycles. The antifreeze performance of the stabilized drilling mud with industrial waste is discussed. The results show that the strength of the stabilized soil decreases with an increase in the number of freeze–thaw cycles. The strength loss of the stabilized soil after freeze–thaw cycles can be effectively reduced by increasing the industrial waste content, especially the content of phosphogypsum in the stabilizer component. Pb2+ ions and Cr6+ ions can be effectively stabilized by industrial waste. The results of the pores test prove that the compactness of stabilized soil solidified by industrial waste residue is greater than that of cement alone.

Nov 1, 2022

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021