Search Documents

By K. [Muthukkumaran

An extensive program of laboratory model tests was undertaken to study the effect of slope on p-y curves under passive loading in dry sand. The paper concerns the method developed in a series of laboratory model tests to experimentally determine p-y curves. Bending moment curves are differentiated by using curve fitting method of cubic polynomial function. The study includes effect of slope angle and relative density on bending moment and non-dimensional p-y curves. The non-dimensional p-y curves for piles on sloping ground under passive load are developed modifying API method by including a Reduction Factor (R) using the experimental results.

Jan 1, 2006

By Reza Y. Khaksar

Presented is a rigorous solution for the three-dimensional stability analysis of vertical shafts (excavations) subjected to the self-weight of the soil based on the upper-bound theorem of limit analysis approach. A rigid-block translational collapse mechanism is assumed, with energy dissipation taking place along planar velocity discontinuities. This mechanism is optimized to obtain the critical failure mechanism giving the lowest factor of safety for stability of shafts. Based on comparisons with other solutions, the method is generally found to be accurate in predicting the stability of vertical cuts.

Jan 1, 2006

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By A. J. Partos

The figures and tables referred to herein are presented in the Proceedings; Volume I, Pages 309 through 316. The 61-story One Liberty Place, at 315 m., is the tallest building 1n Philadelphia and was in 1987 the ninth tallest building in the world. One Liberty Place is supported on drilled piers socketed in heterogeneous metamorphic rock. Design load distribution was 40% on the base and 60% by shaft resistance. Drilled Pier G-10 supporting a T13-A type outrigger column was instrumented. There 1s no uplift load on the exterior outrigger columns. This column supports a 53,850 kN compressive load which includes a 13,440 kN windload. Table 4 presents experimental parameters from straight line interpolation of Mohr failure envelopes for the Wissahickon schist. Lowest values of cohesion (12,200 kN/m2) and angle of internal friction (19°) are at a 50° - 59° angle of foliation. Figure 3 presents a typical pier supported by shaft resistance 1n decomposed (D) and coreable (C) rock and by end bearing (B).

Jan 1, 1991

By Kenneth A. Pidgeon

This paper presents a case history on mitigating vibration problems associated with the installation of steel sheetpiles. The project in-cludes installation of steel sheetpiles for a utility trench within 40 feet (12.2 meters) of a very sensitive manufacturing facility. Numerous production line quality control instruments and manufacturing processes within the manufacturing facility are extremely sensitive to vibrations. To minimize the impact to the owner, we specified that the contractor perform a vibration study using different types of pile hammers. The results and conclusions of the vibration study are presented in this paper.

Jan 1, 1995

By Marius B. Wechsler

A mathematical analysis is developed for the determination of the cases when HP-piles might be replaced by precast concrete piles. The analysis focuses especially on the "integral abutment-bridges" which are used on large scale in the Great Plains of the United States of America, The theoretical considerations are illustrated by a numerical example.

Jan 1, 1992

By Bengt H. Fellenius

.1.1 Prior to commencement of pile installation operation, submit to [Engineer] for [approval] [review], details of equipment for installation of piles. SPEC NOTE: The information requested in 3.1 .1.2 is necessary as input to a detailed wave equation analysis of the pile driving. .1.2 For impact hammers, give manufacturer's name, type, maximum rated energy and rated energy per blow at normal working rate during easy and at termination driving, mass of striking parts of hammer, mass of driving cap, and type and elastic properties of hammer cushion. .1.3 For non-impact methods of installation, such as drilling, jacking, jetting, use of vibratory hammers, or other means, give full details of characteristics necessary to evaluate performance. .2 Impact Hammer SPEC NOTE: Do not exclude a hammer type unless for very specific reason. .2.1 [Drop hammers will not be permitted.] [Diesel hammers will not be permitted.] For final driving of [TYPE] piles, provide a hammer capable of delivering to the pile a non-erratic impact stress not smaller than [VALUE] Pascal and transferring a non-erratic energy not smaller than [VALUE] Joules per blow to the pile head at normal working rate.

Jan 1, 1991

By Adriaan van Seters

"Abstract The content of Eurocode 7 – Part 1 and Part 2 – with respect to piled foundations is outlined. The important role of pile testing is presented and the derivation of the characteristic value of pile bearing resistance is explained. Recommendations for the use of correlation factors are given. The ongoing work of the Evolution Groups on piling is to prepare a revision of Eurocode 7 after 2019. Future topics and changes are highlighted.General outline of pile design by Eurocode 7In his paper for this conference Frank (2014) outlined the various aspects of standardisation for pile foundations, which involves Eurocode 7 as leading for pile construction in Europe. Standards for pile testing and execution of piling works were established in the last 15 years.This paper focuses on the design of piled foundations according to the design code Eurocode 7, which consists of 2 parts:EN 1997-1 Geotechnical design - Part 1: General Rules (CEN, 2004);EN 1997-2 Geotechnical design – Part 2: Ground investigation and testing (CEN, 2007) In Eurocode 7-1, Section 7 – Pile Foundations - deals with the design of piles. The safety concept for pile design is given in Section 2 – Basis of Geotechnical Design - for the three Design Approaches.In Section 7 presents the design of piles according to four methods:1. Results of static load tests2. Empirical or analytical calculation methods3. Results of dynamic load tests4. Observed performance of a comparable pile foundation.Guidelines for the ground investigation for piles is provided in Eurocode 7-2, Annex B.3. In the Annexes of Eurocode 7-2 examples of analytical methods to determine the bearing resistance of a single pile based on the results of various ground investigation techniques are given. Thus calculation models are presented based on design using the results of Cone Penetration Tests (D.6 and D.7) and Pressuremeter Tests (E.3). The Annexes of Eurocode 7-2 are informative.For the interpretation of Eurocode 7, reference is made to Frank et al (2004) and Bond and Harris(2008)."

Jan 1, 2014

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989

By Adam Pickles, Duncan Nicholson, Richard E. Prust, Hoe C. Yeow

"Moorhouse is founded on what at the time of construction were the deepest base grouted piles ever installed in London, specifically designed to accommodate settlement from the proposed development of Crossrail. This paper describes design and construction issues associated with this project with special emphasis on the construction aspects of installing these piles in a heavily congested site in Central London.INTRODUCTIONConstruction of the deepest base grouted bored piles in a congested site in Central London in 2002 posed a number of design and construction problems. To add to the complication, the new structure's footprint is within the safeguarded zone of the proposed new cross London rail link, Crossrail. Therefore the piles were required to be designed to allow for the effects of construction of the proposed Crossrail's tunnels and a new station at Moorgate. The design and construction issues associated with this project are described in this paper and methods used to address such issues are presented.MOORHOUSE DEVELOPMENTThe new nineteen storey high Moorhouse building was commissioned by Moor House Limited Partnership and will form another new Central London landmark building by the British architect Foster and Partners. Two of the four facades feature complex geometry to fulfill the city's planning requirements. The building is a steel frame structure stabilised by a reinforced concrete core. Floor plates span between the core and the perimeter with two rows of internal columns.The complex geometry of the superstructure requires a diagonal ""bandolier"" to transfer floor loads to certain perimeter columns. Another salient feature of the superstructure is the ribs that are provided to act as sloping columns to carry the loads down to the foundations."

Jan 1, 2005

By Musbah A. Hasan, Ahmed M. Nasr, Fauzi Jarushi

Many transmission towers, high-rise buildings and bridges are supported by piles. These structures may be subjected to large lateral loads. Therefore, experimental investigations on model piles under lateral loads were conducted in uniform dry sand. Small-scale model tests were carried out considering the influence of pile length, pile diameter, sand density, roughness of pile surface and vertical load on the lateral resistance of a pile. Furthermore, the effect of pile load eccentricity (e/L) on the ultimate lateral resistance was studied. Investigations, of the influence of various parameters on the magnitude of the coefficient of subgrade reaction (nh), were also performed. It was found that the lateral load capacity of piles increases with increase in pile length, pile diameter, pile surface roughness and increase in the sand density. The results also showed that the coefficient of horizontal modulus of subgrade reaction, (nh), decreases with deflection increase. From the results, the coefficient of subgrade reaction for a smooth pile embedded in medium dense sand would decrease by (134%) when the lateral pile head deflection (yg) changes from (2% to 5%) of pile diameter.

Jan 1, 2017

By S. Kanai

Nodular piles is to be piles provided with several nodular projections along the pile shaft, as shown in Fig. 1. Nodular piles are usually installed through either driving method with hammer or preboring method. This paper presents that the bearing capacity installed through each method is considerably higher than that of cylindrical pile without nodules. This paper also proposes the statistically analyzed unique formulae of the bearing capacity of nodular piles.

Jan 1, 1989

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By Edward L. Hajduk

During sonic logging quality control testing of the drilled shaft foundations for the replacement bridges crossing the Broad and Chechessee Rivers for SC 170 in Beaufort County, South Carolina, irregular signals were observed on a consistent basis near the shaft top elevations. These irregular sonic signals were attributed to access tube ?debonding?, which is the separation of the access tubing from the surrounding concrete. A total of 160 drilled shafts were installed for this project, of which 41 were evaluated using sonic logging testing. Both PVC and steel access tubes were used during the project to allow for sonic logging testing. This paper details the investigation of access tube debonding with time, discusses the solutions used to minimize access tube ?debonding?, and presents the results of the sonic logging testing for the entire project. The solution selected, installation of PVC along the pile length and steel access tubing within 40 feet from the top of shaft, allowed for reliable sonic logging to effectively evaluate the upper portions of the drilled shafts.

Jan 1, 2004

By Eric C. Halpin

"1. Introduction and Backgrounda. In its fundamental form, risk is simply the likelihood of an adverse impact. Expanding on this theme, the Corps of Engineers has broadly defined risk associated with infrastructure as a factor of three distinct elements: a probabilistic assessment of a hazard such as a flood or earthquake; a probabilistic assessment of how the infrastructure performs in the face of this hazard; and a measure of the likely consequences – loss of life, economic damage, environmental impacts – associated with the resulting inundation scenarios.b. The lessons and observations described herein relate to the Corps of Engineers experiences in implementing risk concepts for infrastructure management during the period 2005 through 2013. The Corps of Engineers is a large, decentrally operated and centrally led federal agency that plans, designs, constructs, operates, maintains, and/or manages a portfolio of over 3,000 built dam and levee systems within the United States. The infrastructure in this portfolio is 55 years old on average, and although much of the structures provide for flood risk management benefits, many of the dams deliver multi-purpose benefits. Scale matters – where scale and uncertainty are large, risk concepts provide great opportunity and arrangement for application.c. The amount of organizational change that is demanded for the implementation of risk concepts is considerable and should not be under estimated, but need not be feared if the path others have taken is considered. This paper is, in many ways, an opportunity to step back from the last seven years of implementing risk informed management, check our own azimuth and maturation, and share the purpose and energy behind our own continuing actions. Hopefully, this azimuth check is also beneficial to those that are either considering the use of risk or are in the process of implementing risk concepts.d. Success at managing the massive change related to incorporation of risk concepts will directly affect success of the infrastructure program. The three key organizational elements to consider –human systems such as governance and competencies; policies that outline the who, when, and why of decisions and management; and the processes and technology that outline how work is to be performed - are changed fundamentally. From senior leaders to project team members and all of the people in between, there is a need to discuss, confront, and vet the change and the role people and organizations have in the process. For the Corps of Engineers, with a history of over two centuries, deeply embedded beliefs about infrastructure aren’t transformed over night - the change process is decadal in scope. Given our self imposed “project execution” mantra and corporate objective, risk seemed threatening at first to the cost and schedule of delivering infrastructure projects. In reality, risk concepts have been responsible for savings and cost avoidance of nearly $6 billion over the last three years alone while at the same time justifying increased investment by several fold for the highest risk needs."

Jan 1, 2014

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By Janaka J. Kumara, Takashi Kurashina, Yoshiaki Kikuchi, Takahiro Yajima

"The inner frictional resistance of open-ended piles depend heavily on the degree of soil plugging. Many factors including pile diameter, relative density and end conditions of the piles influence the degree of soil plugging. In this paper, the effects of inner sleeves attached at the pile base on the inner frictional resistance are discussed. The experiments were conducted on a medium-dense sandy ground using smallscale model piles. The results suggest that the inner frictional resistance is influenced by sleeve height for 50 mm diameter piles although it is independent for 30 mm diameter piles. The results also indicate that soil plug height is influenced by the sleeve height. The results of the incremental filling ratio (IFR) showed that penetration of non-sleeved piles is closer to unplugged state than the sleeved piles. The results of the IFR also reveal that the degree of soil plugging is affected by the sleeve height for 50 mm diameter piles although the variation is very limited in 30 mm diameter piles. The results on the coefficient of lateral earth pressure suggested that it increases from 1.08 – 1.75 when the sleeve height is increased from 10 – 100 mm for 50 mm diameter piles.INTRODUCTIONPrevious studies have shown that the behaviour of open-ended piles is different from closed-ended piles (Szechy, 1961; Randolph et al., 1979; Paikowsky and Whitman, 1990). Open-ended driven piles are widely used for deep foundations, in particular in offshore deep foundations. Generally, it is accepted that a short open-ended pile produces a smaller bearing capacity than a similar closed-ended pile (Nauroy and Tirant, 1983). However, a long open-ended pile can produce a similar bearing capacity as a closed-ended pile due to a large inner frictional resistance mobilised between the inner pile shaft and inner soil (Lehane and Randolph, 2002). The ultimate bearing capacity of an open-ended pile, Qu consists of three components as given in Eq. 1."

Jan 1, 2017

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

By Kent C. Werle

This brief discusses the installation and application of sleeved piles of two different types for two different projects, the W, Seattle to Harbor Island Swing Bridge Project and the Seattle Access Project. A description of these relatively novel piling systems is given, as well as some notes on their installation and application. As implied by the term "sleeved" these are piles which consist of two piles, an inner pile combined with an outer concentric sleeve pile. Background, Swing Bridge The Swing Bridge project is virtually unique in the world in that it is a "lift and turn" swing bridge. It is also a concrete, cast -in-place segmental bridge which is designed to be moveable.

Jan 1, 1990

By K. Madhusudan Reddy

Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load?deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.