Search Documents

By Rimas Veitas, James Panton, Erich Steinlechner

"Ductile Iron Piles (DIPs) are a proven, viable alternative to conventional piles, and for the past five years have been successfully used throughout New England. The installation process of DIPs lends itself to both large and small projects. Because of their installation efficiency they provide a substantial cost savings over drilled micro piles. Several New England projects (both end bearing and friction) will be evaluated, focusing on the installation and design procedures.BackgroundThe driven ductile cast iron pile (DIP) is a simple, fast and highly effective pile system. Over the last 30 years over 10 million feet of this pile system has been installed worldwide predominantly in Europe. DIPs are a prefabricated driven pile system utilizing high strength ductile iron pipes which are manufactured using a spun-cast process having outside diameters of 4 5/8” and 6 5/8 inches. The standard pile lengths are 16.4 feet long. The pipes are manufactured with a tapered socket with an internal shoulder for full engagement at the top and a tapered spigot at the bottom. The individual pile sections can be connected with this Plug and Drive® connection to drive a pile of any length.(see figure 1)The DIP system’s inherent advantage is the simplicity of the installation process. The piles are driven to refusal or to a required penetration depth with the use of a high-impact highfrequency hydraulic hammer (ie. Breaker hammer). In most applications the hydraulic hammer is mounted on an appropriately sized excavator (see Photo 2). At the completion of driving the pile, the pile is cut off (see photo 5) and the remaining section of pile is fitted with the appropriate driving shoe and serves as the lead section for the next pile. Being able to reuse the cut off section, yields minimal if any pile shaft waste. The pile is then fitted with an appropriate pile cap plate to receive the load from the superstructure."

Jan 1, 2017

By Alexandra Weidle, Seffen Leppla, Rolf Katzenbach, Matthias Seip

"A lot of different deep mixing systems have been developed in the last decades for a wide spectrum of applications, e.g. retaining and foundations systems, soil improvement, sealing of toxic substances or dyke strengthening. The paper will deal with special aspects of constructions with deep mixing systems for infrastructures like soil improvement for cyclic loadings and underpinnings in difficult soil conditions by presenting cases from engineering practice.1. DEEP DRY SOIL MIXING FOR SOIL IMPROVEMENT OF RAILWAY TRACKS IN VERY SOFT SOILS1.1 IntroductionRailway tracks are set into vibrations by train passing. In very soft soil this leads to long-term deformations which lead to speed limits, temporary closings and big maintenance efforts. The energy of the dynamic loading is transmitted into the soil by compression and shear waves and at the surface by rayleigh waves (Wood 1968). The expansion of the waves are influenced by•,thickness of the soft soil layer•,density of the soft soil layer•,stiffness of the soft soil layer•,saturation of the soft soil layer•,frequency of the dynamic loadingThe frequency of the dynamic loading depends on the train velocity and the distance of the wheels and wheel sets. If the frequency of the dynamic loading is in the range of the natural frequency of the soft soil layer the vibrations increase extremely (Lieberenz et al. 2003). As a result the long-term deformations will increase as well.To avoid these long-term deformations and the resulting operation restrictions and maintenance efforts an adequate soil improvement is necessary. For the optimization of the soil improvement field tests have been carried out.1.2 Experimental field testsThe field tests have been carried out at a 300 m long test track with five different setups, each 30 m long:•,test track TS 0: no soil improvement•,test track TS 1: soil improvement with single lime-cement-columns 5.9 m deep (Figure 1a)•,test track TS 2: soil improvement with single lime-cement-columns 5.9 m and 10.4 m deep (Figure 1b)"

Jan 1, 2015

By A. Le Kouby

We present in this paper the results of a parametric study carried out in a calibration chamber on instrumented model piles. The aim is to point out group effect on piles within a group through their resulting shaft friction and tip resistance. The methodology relies on the study of the influence of adjacent piles on a "reference" pile. The soil used is a silica sand (Fontainebleau sand). The influence of parameters like pile spacing, number of piles and installation order are evaluated. The results show a positive effect on shaft friction of the group effect and a negative effect on tip resistance. Efficiency factors are defined in order to have a better view on the parameters influencing the response of the pile within a group.

Jan 1, 2006

By I. D. Dayal, Anil Kumar Jain

"Cutoff walls are frequently used to slow down or prevent seepage of water through and/or around dams. Cutoff wall is a type of seepage barrier structure designed to reduce the flow of water underneath temporary or main dam. There are number of techniques for the construction of cutoff walls including concrete, Jet grouting and permeation grouting. NHPC LTD, a premier Govt. of India undertaking has been instrumental in the hydropower development within the country & in nearby countries like Nepal & Bhutan since last four decades. NHPC LTD has completed more than 20 hydro-electric projects with total installed capacity of 6587MW (including capacity addition by JV- NHDC). In all these projects, different types of dams and spillways were constructed in not so benign to extreme challenging geological set up. There has always been challenge associated with the temporary diversion works. The project sites sometimes incur huge river bed excavations in case of concrete gravity dam founded on rock foundation at large depth. The challenges for minimizing the seepage have been well taken care by constructing the dedicated seepage barriers. The construction of cut-off walls have progressed from “conventional continuous trench backfilled with conventional concrete or plastic concrete” to “grout curtain”, to “jet grouting” to the “concrete cut-off wall” , the last being the most sophisticated & credible seepage barrier.The efficiency of the cut-off walls are monitored by the seepage quantity observed (reduction of the seepage flow), uplift pressures or exit gradients after construction of cut-off walls. For construction of the main concrete dam, required space is created by the river bed excavation for placing the dam foundation on sound rock. Sometimes there is deep river bed excavation from 30 to 40 m depth or even more as per the available rock profile. Temporary coffer dams are constructed for diverting the river flow through diversion tunnels / channels etc. In deep river bed excavation; there are high chances of the significant seepage through the coffer dam foundation / river bed material due to high hydraulic gradients. Seepage and piping are the main causes of the failure / damage of the temporary coffer dams. If the seepage quantity is too high, then it becomes difficult to handle it by dewatering in the dam pit. Dam concrete is required to be placed unhindered to have a monolithic construction of dam blocks & to have faster construction in the working season. Cut-off walls increase the seepage path considerably thus reducing the exit gradient and further reduction of the seepage thus helping in maintaining the seepage free area for working."

Jan 1, 2016

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By Stephen Darmawan, Mahdi M. Disfani, Arul Arulrajah, Alireza Mohammadinia

Deep mixing using cementitious compounds is an in-situ method of ground improvement for improving the strength, compressibility of loose sand. Artificial light cementation can increase the stiffness of loose sands significantly and reduce the settlement of loose deposits. The increase in contact area between the particles with a thin layer of cementitious agent depends on the confinement and void ratio of the soil mass. Hence, the stiffening effect of cementation not only depends on the type and amount of cementing agent and inter-particular force chain of loose deposit but also depends on the stress level at the time of cementation. In addition, the cementation effect in loose deposits can be deteriorated at relatively low strain levels. Decementation softening can cause detrimental and irreversible impacts on the soil deposit. This study investigates the effect of initial confinement and subsequently the initial void ratio at the time of cementation on small strain behaviour and decementation softening of cemented loose sand under ko loading. The effect of inter-particular contact of sand particles based on the specific surface area and also soil density was also investigated by means of shear wave propagation. This study present insightful information on effect of primary consolidation stress levels, density of soil and cementation level on softening and collapse of loose deposits improved using deep soil mixing technique. Better understanding of soil-cement interaction by optimization of binder content for deep mixing activation can lead to increasing the level of confidence in using this technique in ground improvement applications.

Jan 1, 1900

By Frank Rausche

Why testing What tests can be done Dynamic load testing Loading device Measurements Analysis Examples

Jan 1, 2001

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By John L. Walkinshaw

It is obviously not possible in the time given me today to review in great detail all the research of the past 20 years that the (FHWA) has sponsored or participated in. In this presentation I will highlight some of the principal programs that I am familiar with. This handout lists practically all the reports prepared for the FHWA involving deep foundations and some related work involving the same structural elements (piles, shafts, ground anchors).

Jan 1, 1993

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By D. Cantali

This paper will be presented in two parts. The first part will present the latest advancements in pile installation techniques using state-of-the-art press-in piling technology by Giken. By pressing in sheet piles and large modulus contiguous steel tube pile walls – as opposed to the more traditional installation methods using percussive hammers or vibrators – retaining structures can be constructed effectively noise and vibration free. For over water and coastal projects with limited access, this provides significant environmental benefits in the form of minimising the construction foot print and the impact to surrounding communities and the marine natural habitat. Typical noise and vibration data will also be presented. The second part of this paper will review the current manufacturing techniques for sheet piles and introduce innovative new materials used in the current piling market for embedded sheet pile walls. Materials include long service life non – ferrous materials such as new age plastics and fibre reinforced polymer piles. Their excellent long term performance and durability make them an effective solution in the marine environment. For steel piles, a number of steel grades with reduced corrosion characteristics will also be discussed including a newly developed steel to combat corrossion in the low water zone, an area often exhibiting the highest moments in a retaining wall. A number of project case studies will also be presented to reinforce their relevance in today’s changing construction landscape.

Nov 1, 2022

By Ali Nasirian Ph. D., Gabriel Carvajal

To facilitate the safer and more secure transportation of inmates from San Diego Central Jail to the new San Diego Courthouse, the County of San Diego committed to building a new transfer facility as part of the downtown developments. The transfer facility includes a three-story underground structure adjacent and connected to the Central Jail and a 60-ft deep, 23-ft diameter, 320-ft long tunnel. The tunnel starts at County Jail, passes underneath Western Regional Detention Facility (Old Jail) and, ultimately, connects to the State Courthouse. Condon-Johnson & Associates, Inc. (CJA) was selected to install the temporary shoring shaft for the underground structure as well as three arrays of canopy pipes to support the tunnel’s Sequential Excavation Method (SEM) construction. CJA installed the rectangular 56-ft deep access shaft shoring with three levels of bracing, and a combination of secant piles, soldier piles, and timber lagging. The shoring also included a sliding bridge at top to provide access for trucks to enter and exit from county jail during the duration of construction. Following shoring and shaft excavation, CJA installed and grouted 7-5/8” dia. canopy pipes in 3 reaches, parallel to the longitudinal design line of tunnel with a slight lookout angle. CJA installed 24 each canopy pipes, 99-ft from face of shaft at reach 1, 21 each, 80-ft length canopy pipes at reach 2, and 21 each, 75-ft length pipes at reach 3. CJA confirmed canopy pipe alignment via Inertial Sensing Gyro. To mitigate the possibility of settlements caused by the tunneling operation underneath Old Jail strip footing and grade beams, CJA also performed void fill grouting. Sleeve port grout pipes (SPGP’s) were installed inside the Old Jail basement and grouted with the use of packers as the tunneling operation passed underneath the Old Jail. In detailing various aspects of the construction, this paper aims to magnify the innovative solutions for shoring, canopy pipe installation and void fill grouting challenges as well as the state of the art quality control measures undertaken by CJA.

Oct 1, 2022

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY consists of a dual-span 1,982.5-ft long cable-stayed bridge with approach spans of 2,545 ft on the NJ side and 2,788 ft on the NY side. The bridge is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Drilled shaft resistances for design were based on load tests as described in a companion paper (Dapp et al. 2016). This paper presents the main foundation design considerations and challenges. The approach to construction of the rock sockets, with a focus on quality in order to support the use of high nominal values of side and base resistance, is described. Lessons learned from this project and their application to future similar projects are presented.INTRODUCTION AND BACKGROUNDThe Goethals Bridge Replacement (GBR) project is a Public-Private Partnership (P3) that represents a major milestone for the Port Authority of New York and New Jersey (PANYNJ) in its distinguished history of bridge building in the greater New York City metropolitan area. The new bridge will replace the existing Goethals Bridge, named after Major General George W. Goethals, Chief Engineer of the Panama Canal and the first consulting engineer for the Port Authority. The existing Goethals Bridge along with the Outerbridge Crossing and the Bayonne Bridge comprise the three Port Authority bridges connecting Staten Island with New Jersey. The existing Goethals Bridge and the Outerbridge Crossing are cantilever truss structures and both opened on the same day in 1928. They were designed by J.A.L. Waddell under the supervision of the eminent engineer Othmar H. Ammann (1879-1965), who was the designer of many other iconic bridges in the NY City area including the Bayonne Bridge (1931), the George Washington Bridge (1931), and the Verrazano Narrows Bridge (1964). The designer of record for the replacement Goethals Bridge is Parsons Corporation, which is the successor firm of Robinson & Steinman, whose principal David B. Steinman was also a notable NY area bridge designer and a contemporary and rival of O.H. Ammann.The replacement Goethals Bridge is supported on over 200 rock-socketed drilled shaft foundations. Each main pylon tower is supported on a group of six 9-ft diameter drilled shafts and each anchor pier is supported by two 10-ft diameter shafts. Each approach pier consists of a two-column bent with each column supported on a rock-socketed drilled shaft. A rendering of the Main Bridge crossing the Arthur Kill is shown in Fig. 1."

Jan 1, 2016

By Maral Papazian Bedian

"Case 2. 100th Street Bus Depot: Elimination of Deep Caissons in Favor of Spread FootingsThe PROJECTThe 100th Street Bus Depot is a new five-story bus terminal for the New York City Metropolitan Transit Authority occupying one city block in Manhattan between 99th and 100th Streets, and between Lexington and Park Avenues. It replaces a former two-story garage, built in the 1890’s and initially used as a trolley-car barn. The new structure is a steelframed building with concrete floors and includes a partial basement near its middle. The easternmost column line with design loads of 10 MN (1,125 tons) is within 1.5 m of the underlying multi-tube Lexington Avenue subway system. To support the new columns along the subway line, the project bid plans had called for 1 m diameter and 17 m deep drilled shafts. The upper 14 m of each unit would have required 50 mm separation from the surrounding rock to prevent stress from being imposed on the roof and walls of the adjacent tunnel. The column loads were thus transferred to below the base of the tunnel and supported by 3 m long sockets in bedrock. The bid documents contained extensive test boring information, which revealed that the project site was underlain by massive Manhattan Mica Schist bedrock within just 3 m below street level. In fact, the Lexington Avenue two-level and multi-tube subway had been tunneled through this rock circa 1910, leaving an about 6 m thick solid roof over the upper-level subway. The NX rock core recovery values were near 100 %, with average RQD of 75 %.The CHANGEThe Bus Depot project was let as a design/build contract with a very aggressive fast-track schedule. Both the pre-bid preliminary design and the subsequent final design by the Contractor’s own hired design engineers relied heavily on very restrictive codes, including unnecessarily conservative approaches to seismic design. Any suggestion for value engineering change was undesirable and was strongly resisted. Yet, objecting against the blind reliance on codes in foundation design, the author questioned the real need for the deep drilled shafts to support the columns along the subway. The unsupported statement that no stresses from the new structure can be imposed on the roof and walls of the adjacent tunnel was not sufficient reason for the drilled-shaft design. Unconvinced that deep shafts were necessary, the author rushed to MTA’s warehouse where many rows of rock core boxes were neatly stacked. Careful inspection and some simple testing of the rock cores with the blows of a geologic hammer gave support to the reservations about the design. Later, as expected, the schist bedrock at this site was found to be hard to very hard with unconfined compressive strength values estimated to range from at least 70 MPa to over 100 MPa (10,000 psi to 15,000 psi). The tensile strength of the rock was assessed to be minimum 5 MPa (750 psi)."

Jan 1, 2003

By Joshua R. Omer

A numerical model is developed for predicting the load transfer and settlement behaviour of vertically loaded, bored cast in-situ piles. Based on analysis of full-scale pile tests, closed-form equations are formulated to uncouple the shaft and base transfer resistance components of the pile/soil system. Appropriate parameters are introduced to take into account: (i) the shaft resistance distribution in unlined and partially lined piles, (ii) the effects of ?soft toe? (voided toe pile) behaviour on base resistance development. For convenience, an interactive computer program has been developed in Matlab? with a user friendly interface system. The program can be applied to predict the complete load-settlement curve and axial force distribution in bored cast in-situ piles if reliable soil test data are available. To demonstrate its validity, the proposed method is applied to 4 test piles, which are also analysed using two previously published methods: (a) elastic solution method and (b) layer discretisation method. Methods (a) and (b) above are based on load transfer (t-z) and finite element models respectively. It is shown that the proposed method yields axial force distributions and load-settlement curves that are in good agreement with the observed pile test data.

Jan 1, 2010

By Edmund Cardoza

In the spring of 1993, construction began on an ambitious building project in Boston, Massachusetts. The Shriners organization committed to offer state-of-the-art adolescent burn treatment and rehabilitation in its Boston facility by expanding in a most unusual way. In short, the concept included installation of caisson foundations and perimeter slurry wall panels to enable construction of a completely independent structure around and above the existing, continually functioning, hospital. Two distinct phases of work were detailed in the Contract Documents. At the completion of the first phase, patients will be moved into the new building, above, and demolition of the old structure, beneath, will be performed. In Phase I, sections of the slurry wall and caissons, located outside the footprint of the existing building, were planned. The next phase of the work includes the installation of the remaining caissons and slurry wall. Once excavation is completed, the balance of the new hospital structure will be constructed from the bottom upward, connecting to the under side of the new structure.

Jan 1, 1994

By Paul Suver

"The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.CLSCW Description:Closed end steel pipe of varying outer diameter (O.D.) is installed by various technologies at varying depths depending on subsurface geology. The wells are arranged as stand alone wells or in groups joined in parallel or in series or in a combination of both. These pipes may also serve a dual function as foundation supports, deep foundation pile, anchors or earth retention components. These wells are then internally coated to minimize corrosion. The wells are then plumbed and capped to create a vessel equipped with a supply and return water line.The stand alone well or group of wells is then used as a ground heat exchanger for a ground source heat pumps located in or around the building.The ground source heat pumps provide heating and cooling to the building either with a traditional ducted distribution system or with radiant heating and cooling. These systems can reach efficiencies three times greater than traditional gas fired heat sources and five times greater than traditional air conditioning sources."

Jan 1, 2017

By Ahmed Elmekati, Frederick C. Rhyner, Steven R. Lowe

"The current phase of the Pacific Park development (formerly, Atlantic Yards) in Brooklyn involves constructing buildings on a platform over an existing LIRR rail yard. To preserve the maximum amount of space in the already congested yard and protect the yard which remains in service during construction, high capacity foundations are being designed well above previous capacities in the area. In addition to spread footings and small mats, various diameters of drilled piles are being used at design capacities ranging up to 600 tons. The piles are generally grouted at low pressure, up to about 50 psi. Load tests for various drilled elements, including piles, tiedowns and soil anchors, have confirmed allowable side resistance (bond) stresses in dense sand ranging from 20 to 30 psi. Testing with different rigs and operators has shown that down-the-hole hammers are feasible, but the installation techniques, types of equipment and size of the pile make a significant difference. The results show that more cost-effective foundations are possible when ample testing confirms expectations.I INTRODUCTIONThe Long Island Rail Road has operated a mainline on Atlantic Avenue since the 1800s, with a terminal at the intersection of Atlantic and Flatbush Avenues. In the early 1900s, the mainline was reconstructed in a cut and cover tunnel section. The LIRR’s Atlantic Yard was constructed circa 1908 to service the terminal. It was depressed about 25 feet below street grade to coincide with the LIRR’s mainline tunnel under Atlantic Avenue. Record drawings indicate that the gravity retaining walls lining the perimeter of the yard and other ancillary structures had been designed for an allowable bearing pressure of five tons per square foot (tsf). Perhaps by coincidence, the mat foundation for the tower of the Williamsburg Savings Bank was also designed for five tsf in 1929.Figure 1 shows a typical geologic section through the site. The geology and subsurface conditions in this part of Brooklyn consist of fill generally five to 20 feet deep underlain by dense to very dense sand and gravel; in places, with numerous cobbles and boulders which make pile installation challenging. The sand strata that are on the order of 150 to 200 feet thick were laid down by glaciers during the last ice age and have been heavily precompressed. The sand strata are underlain in places by remnants of the Cretaceous-era Raritan Clay formation and Fordham Gneiss bedrock. Because of this, the sand strata generally provide excellent support for shallow foundations and the allowable bearing of five tons per square foot is usually easily justified."

Jan 1, 2016

By Brian W. Wilson

A case study is presented that describes the design and implementation of a combined blast densification and deep dynamic compaction program which was undertaken to improve the foundation soils for a proposed tailings dam raise in Ontario, Canada. Based on the results of the geotechnical investigation it was determined that the foundation of the dam would be situated on tailings of both variable thickness and density, much of which would be susceptible to liquefaction under the design earthquake for the region and type of facility. Blast densification trials were completed by the owner and the results of these made available to prospective tenderers in response to a call for a fixed price contract for the design and implementation of a densification program for approximately 800,000 m3 of foundation tailings. The variation in tailings gradation and the impacts of such on the ground improvement program are discussed, as are details of both the additional blast densification field trials completed by the contractor, and the selected blast pattern and explosive charging used for production blasting. The applicability of the various ground improvement techniques to the actual conditions encountered, and the results obtained are also discussed.

Jan 1, 2010