Search Documents

By Chunli Wei, Mark Jen, Xiaojun Wang

"After more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges. Each bridge includes 1,650 feet long signature steel composite cable-stayed bridge, a 2,789 feet long New York approach and a 1,889 feet long New Jersey approach. The superstructure of each approach is supported on a series of two-column concrete piers and each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock.A performance-based methodology was followed for the strength and extreme event limit states design of the drilled shaft foundations. The design for seismic loads has been performed using the AASHTO Guide Specifications for LRFD Seismic Bridge Design. For all strength and service loads, the AASHTO LRFD Bridge Design Specifications were used. Since the longitudinal and confinement requirements in the two specifications vary, the minimum longitudinal reinforcement was based on the more stringent requirements of the two codes. A design example is presented to illustrate the methodology in bridge deep foundation design using nonlinear time-history global analysis results with soil-pile interaction represented by sets of horizontal and vertical nonlinear soil springs along the drilled shaft, based on the soil and rock properties from the boreholes test results. In this paper the design methodology implements strain limits related to earthquake intensities and damage levels to calculate the capacity using XTRACT analysis, which aids designers to adopt applicable provisions that meet specific design requirements.INTRODUCTIONAfter more than 85 years of service, a critical link between New York and New Jersey, the Goethals Bridge over the Arthur Kill waterway, is being replaced with two new parallel bridges designed to carry vehicular traffic and a future mass transit corridor. They include two 1,650 feet long signature steel composite cablestayed bridges with 260 feet tall V-shaped concrete gateway towers (Figure 1). The approaches consist of continuous pre-stressed concrete girders. The New York approach is a single structure consisting of 18 continuous spans, sloping at 4% for a total length of 2,789 feet without expansion joints. Similarly, the longest continuous portion on the New Jersey approach, with a similar slope, consists of 11 spans for a total length of 1,889 feet without expansion joints. The superstructure of each approach is supported on a series of two-column concrete piers that vary in height from 121.3 feet near the cable-stayed bridges to 11.8 feet near the abutments. Each column is supported on a single large diameter drilled shaft varying from 4.5 to 9 feet in diameter and anchored 45 feet below ground into the underlying rock."

Jan 1, 2016

By Ingrid Engeset, Solve Hov, Arnfinn Endal, Per-Anders Mortensen, Priscilla Paniagua, Bjørn Kristian Fiskvik Bache

During the last decades, it has become common practice in the Nordic countries to use dry deep mixing in soft clays with lime and cement in for example deep excavation pits in soft clay, or as a reinforcement of the passive zone within sheet pile walls. The shear strength of stabilised soils is affected by the stress conditions during curing and shearing. However, this is normally not taken into consideration. As the strength of the stabilised clay is stress dependent, excavation of the overlying soil will lead to a reduction of the confining stresses in the underlying stabilised soils which means that the shear strength will also be reduced. Under embankments on the other hand, the effect is reversed as the shear strength will be increased. In this study, laboratory tests have been performed on stabilised soils cured and tested under different stress conditions to quantify the stress effects in a Norwegian sensitive clay. In addition, direct simple shear tests on samples from in situ columns have been made with varying normal stresses. Results are presented showing an increase of shear strength of the stabilised soil with increased curing stresses, and an even higher increase with increased confining stress during shearing. The results are compared to field measurements along with a discussion of practical application of the findings.

May 1, 2022

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Jon Huff, Jeffrey Donville, Hannah Iezzoni, Dan Stevenson

Occasionally, in the design of deep foundations for a structure, a single deep foundation element may be used to support a building column. The most common type of element used in such cases is a drilled shaft (also referred to as a drilled pier, caisson, or bored pile). However, as installation capabilities have improved, large diameter augercast piles are increasingly more common. While drilled shafts and augercast piles differ significantly in construction methods, in the eyes of the International Building Code (IBC), both are treated as cast-in-place deep foundations and must comply with many of the same code provisions. Deep foundations are required to be braced such that lateral stability is provided in all directions, however isolated, cast-in-place elements that have a diameter (D) of at least 2-feet and a length (L) not more than 12 times the diameter can be an exception. In response to the concerns raised by some member professionals, the Deep Foundations Institute’s (DFI) Augered Cast-in-Place Pile and Drilled Displacement Pile Committee took a closer look at the code and its applications, the historical development of the code language through the years and performed analytical modeling to evaluate the impact of this ratio on a pile’s stability. The question is whether the limiting ratio included in the IBC 2018 code provisions is justified, or whether different criteria should be used to determine when isolated deep foundation members are allowed.

Sep 8, 2021

By Monica R. Garcia, Antonio Alberto S. Correia, Paulo J. Venda Oliveira

"The aim of this paper is to analyze the creep behavior of a Portuguese soft soil stabilized with binders in one-dimensional conditions, based on oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. The results show that the best binder type for this soil, in terms of creep behavior, is composed of Portland cement and fly ash with a dry weight proportion of 75/25, as this promotes the development of secondary pozzolanic reactions. The results also show the decrease in the secondary compression index with the increment of the binder content, since it promotes an increase in the cementation bonds between soil particles. The general analysis of the results shows a clear dependence on C??and qu, until values of qu of 1500 kPa; after that this relationship is negligible.INTRODUCTIONThe geotechnical structures (such as embankments, dams and buildings) built on organic soils exhibit notable creep deformations, which increase the maintenance and exploitation costs and can even compromise their functioning. To attenuate the creep effects of the soft ground, some improvement techniques are frequently used, such as preloading or reinforcing the soil foundations with vertical rigid inclusions, like concrete piles, stone columns or deep mixing columns (DMCs). However, the installation of DMCs in the soft ground induces (via the arching effect) a transfer of stresses from the soft soil to the DMCs, which causes an increase in the creep settlement on the DMCs (Venda Oliveira et al. 2011).Notwithstanding the fact that the creep behavior of clays has been the object of several studies (Leroueil et al. 1985; Mesri and Castro 1987; among others), the study of the creep behavior of soil-binder admixtures has been practically ignored by the scientific community. The few studies on this theme have revealed that a stabilized soil’s creep behavior is dependent on: the type of binder (Venda Oliveira et al. 2013), the binder content (Correia 2011; Bobet et al. 2011; and Venda Oliveira et al. 2013), the stress level applied during the creep phase (Venda Oliveira et al. 2013), the organic matter content of the natural soil (Venda Oliveira et al. 2012; 2014), and the curing conditions (humidity, vertical stress applied during curing, and curing time) (Correia 2011; Venda Oliveira et al. 2012).The aim of this paper is to contribute to a better understanding of the creep behavior of a soil-binder admixture, by examining the results of oedometer creep tests. The study focuses on the analysis of the effect of the binder content and binder type on the creep behavior of a stabilized soil. Additionally, the creep behavior is correlated with the effective vertical yield stress and the unconfined compressive strength (UCS)."

Jan 1, 2015

By Chandramohan P. V

A unique tension pile where the pull is at a point a certain distance below the top of the pile. The pull is transferred by a cable consisting of high tensile strands. The HDPE duct of the cable prevents bond between the strands and pile concrete in upper portion. While soil friction on the pile will act downwards on the whole length, there is tension in the bottom portion of pile, there will be compression at the top portion.

Nov 1, 2022

By Danny Déry-Chamberland, Peter Bowman, Michael Byle

"The Barrage des Quinze dam is a concrete sluice dam consisting of 19 spillway sections, each of which is approximately 7.6 metres wide and 14.5 metres deep. Rehabilitation efforts being performed on the dam including demolition and improvement of the roadway and spillway sections and grouting to mitigate underseepage. Initially, conventional cement grouting was attempted and was successful in 14 of the spillway sections, but unsuccessful in 5 of the sections due to the high water flows which washed the grout away. The removal of the roadway and portions of the piers during construction temporarily reduced the stability of the structure limiting grouting pressures that could be applied. This and the substantial high water flows (leakage) beneath the dam between the concrete/rock contact and within fractures in the upper rock formation created a challenging situation to create a cutoff.A grouting solution was developed that involved implementing several different grouting methods and materials including balanced high mobility grouts (HMG); low mobility grouts (LMG); polyurethane grouts; and sodium silicates. Because of the critical scheduling for the work, multiple approaches were planned and made available on site so that the work could proceed with the best technology with little, if any, time loss. The end goal of the grouting program was to create a seepage cutoff beneath the 5 sections of the dam in a stepwise process. The initial step was to fill the large openings and create a grout barrier to reduce the high water flow. The second step was to seal the contact between the base of the dam and the bedrock; and the third step was to complete closure by grouting a deep grout curtain into the underlying rock. Other features of the work included an extensive grout mix testing program, water pressure testing, borehole camera survey, and monitoring of the grout injections."

Jan 1, 2016

By Travis A. Shoemaker, Mitchell S. Youmans, Nancy T. Chin, Michael S. Senior

A geologic assessment and stability analysis of the right abutment of Boundary Hydroelectric Dam in Pend Oreille County, Washington was completed in May 2017. The stability analyses identified a potential failure plane of a rock block that supports a bridge abutment, and weight restrictions were established to reduce the bridge loads. To restore full use of the bridge, a long-term stabilization solution was designed. A two-phased construction approach was implemented to reduce risk: (1) cable lashing and wire mesh and (2) 24 permanent post-tensioned tiebacks. The tiebacks were located and sequenced based on stabilization effect and site access to incrementally ease the bridge loading restrictions throughout construction. Due to weight restrictions and site tolerances, all work was performed with rope access construction methods. The contractor’s means and methods, tight drilling tolerances, and an exploratory adit within the rock block made the construction uniquely challenging. Due to limited exploratory data and irregular rock face geometries, the design orientation, location, and tolerances of the tiebacks were established in a 3D Building Information Model (BIM). The 3D model was revised frequently during construction to 1) model the as-drilled conditions of the tiebacks; 2) compare with the remaining proposed anchors; 3) anticipate the contractor’s sequence to reduce risk during drilling; 4) accommodate the contractor’s requests for information; 5) make design changes based on field observations; and 6) incrementally assess rock block stability. The 3D model was created using BIM software and automated using custom programming to link per-plan, proposed, and as-installed tiebacks between the 3D model, field logs, and a stability analysis. This system allowed for a near real-time 3D model and stability analysis, which were easily communicated between the design team and field staff. This workflow and automated model nearly eliminated manual editing of the 3D model, accelerated contract document response time, and helped reduce risk for the owner, contractor, and engineer. Here, we present a successful case study utilizing the Observation Method and a real-time 3D model to complete a project with numerous complexities relating to design, communication, and risk.

By Sandeep Pattnaik

Spring stiffness of soil and rock at different depth is often required for a pile structural model. If the pile is rested in multiple layers of soil, then it is rather more complex to simulate the soil in a structural model. The spring stiffness will vary based on density of soil strata over the depth. When a pile is socketed in weathered rock followed by a soil layer, a sudden change in subgrade modulus can influence the pile deflection drastically. Determination of soil spring and simulation of the pile in this condition required correct interpretation of subgrade modulus. The conventional approach of pile spring calculation underestimates the spring stiffness by ignoring underlaying stiffer layers. A finite difference method (FDM) of analysis can reasonably estimate the p-y of soil / rock based on subgrade modulus of each layer. However, the transition between the layers can be better simulated as per the deflection pattern of the pile. The lateral deflection of the pile is mainly dependent on the stiffness of soil layer surrounded by the pile. Generally, the lateral influence of a pile varies from 4D to 6D depending on the soil type. Therefore, soil spring stiffness around the pile would require special attention of a Geotechnical engineer to avoid uncertainty in the prediction of pile behaviour. In this paper, emphasis has been given to develop an approach for pile spring stiffness design. A standard software program LPile has been used to develop p-y curves of soil and rock layers at different depths and then converted to soil/ rock springs over the depth. Modulus of Subgrade Reaction as given in IS 2911 (Part2) was also used to correlate the spring value for different type of soil. Obtained analytical results were compared with full scale field trial for lateral deflection of pile. A good agreement between these two approaches has been established. The effect of soil structure interaction in the structural model shall be simulated by assigning an equivalent vertical and horizontal soil spring, which is developed by Winkler’s soil spring approach. A simplified design principle for calculating the pile spring is discussed in this paper. This approach has been extensively used in Mumbai metro elevated line pile design.

Nov 1, 2022

By Karen Dawson

This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Daniel Magill, Jim Gentry

"Acrylamide chemical grout (C3H2NO) has been successfully used for over 50 years to control groundwater and stop infiltration. This paper will address three unique projects involving the control of groundwater with each study providing special circumstances and geological conditions: encapsulation of radioactive hazardous waste in the United States, a tailings dam for a large copper/gold mine in Argentina and 27 miles of leaking subway in Canada. The primary reasons for selecting acrylamide grout were based on the following characteristics: thinnest chemical grout on the market, a true solution grout which contains no suspended solids in the blended product, flexible gel set times, and a 362 year half-life in soil as determined by the U.S. Department of Energy.INTRODUCTIONChemical grouting has been successfully used for over fifty years to control the movement of groundwater in a wide variety of applications including:•, Hazardous Waste Containment•, Subways & Tunnels•, Mines & Tailings Dams•, Concrete & Earthen Dams•, Underwater Structures•, Beneath/Around Underground Structures•, Mainline Sewers, Laterals, Manholes•, Large Soil Stabilization ProjectsThis presentation will review three projects where chemical grout was utilized to address some very difficult water control challenges, each providing special circumstances and geological conditions:1. Pre-construction seepage control at a mine tailings dam2. 27 miles of leaking subway3. Encapsulation of radio-active hazardous wasteThe reasons for selecting acrylamide grout as the solution for controlling groundwater in these selected projects were based on the following characteristics:1. Acrylamide grout is the thinnest chemical grout on the market2. No suspended solids which allows acrylamide grout to travel anywhere water can travel3. Flexible gel set times from 5 seconds to 10+ hours4. U.S. Department of Energy studies conclude that acrylamide chemical grout has a 362 year half-life in soil and can reduce the permeability of rock/soil to less than 10-8 meters per second (m/s)"

Jan 1, 2017

By Thai Nguyen Ph. D

Dynamic Load Test (DLT) on driven piles has been performed routinely all over the world. In several recent projects, even 100% testing has become a norm where every single pile is dynamically load tested. In these cases, most piles are of uniform sections, making the field analysis (CASE method) straight forward. The CASE method, which has been used for the last 50 years, however, is only applicable to uniform piles to monitor pile driving stresses as well as pile capacities. Signal matching analysis can handle different configurations. However, the analysis used to require user inputs (i.e., non-automatic). Manual signal matching analysis, which can solve non-uniform solutions, traditionally takes hour(s) to complete for one blow. As such, the real-time pile driving stresses and resistances had traditionally been relying upon the CASE method, using typical range of CASE damping (JC). Until 2021, due to the lack of a rigorous instant signal matching analysis for non-uniform piles, no tool was available to help engineers evaluate non-uniform piles in real-time. An inexperienced field engineer may overlook this shortcoming when evaluating peak driving stresses. Furthermore, ultimate bearing resistances for non-uniform piles may require further evaluation to account for the non-uniformity of piles if relying on the CASE method. This paper highlights recent advances in instant Signal Matching Analysis on non-uniform piles, allowing field engineers to monitor stresses and resistances of non-uniform piles during driving.

Oct 1, 2022

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 fUsec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases. and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

May 11, 2007

By Faisal Shalzad, Adnan Anwar Malik, Tadashi Maejima, Jiro Kuwano

Single helix screw piles carry most of the structural load through end-bearing if the helix is embedded in the dense bearing layer. The tip condition of the central shaft of the screw pile can be closed, closed with cutting blades, opened with flat cut, and opened with wedge shape cut and its selection is based on the insitu ground conditions. These different end conditions of the central shaft disturb the ground differently, leading to the change in bearing capacity. In this study, an attempt is made to investigate the effect of open and close-end screw piles on installation effort (installation load and torque) and bearing performance in the dense bearing layer. The model steel screw pile with a pile shaft diameter of 21.7 mm and helix diameter of 43 mm is used in this study. Test results show that the open-end screw pile required less installation effort than the close-end pile that penetrated the bearing layer by 1Dhwith an unplugged condition. Further, the open-end screw pile shows a higher bearing response than the close-end screw pile if it enters the bearing layer with an unplugged condition.

Oct 1, 2022

By Rick Deschamps, Amanda Blank, Matthew W. Drewek, Michael P. Walker

The Prairie du Sac Dam, located on the Wisconsin River, northwest of Madison, Wisconsin, was constructed 1912-1914. The spillway is an Ambursen-type, consisting of a series timber pile supported pier and buttress walls and rollway slab. The timber piles supporting the spillway, numbering approximately 5,000, have deteriorated, and the spillway structure was underpinned with over 700 micropiles as part of a design-build construction project. The underpinning micropiles needed to be arranged to avoid interferences with the existing timber piles, requiring the micropiles to be installed in the open spaces between the piers and buttresses. Inevitably, the installation of the new micropiles encountered obstructions, including existing timber piles out of alignment, as well as timber piles used to support the original construction activities and sheet pile used to control water during the original construction. This paper discusses using finite element analysis to model the spillway structure to estimate the vertical and horizontal stiffness with an extensive sensitivity analysis was performed during the design phase to account for anticipated construction challenges and potential variations in the underpinning performance. The inherent rigidity of the spillway structure allowed for load distribution to the underpinning system even when new micropiles needed to be re-located and aligned to avoid interferences with existing timber piles and other abandoned foundation elements dating back to original construction.

Sep 8, 2021

By Alexander Scheuermann, Martin D. Larisch, David J. Williams

"Drilled displacement piles (DDP) have been used around the world for decades as foundation elements for structures and embankments. Typically the pile toes are designed to penetrate into stiff or dense soil formations to achieve sufficient base resistance. Recent research at The University of Queensland in Brisbane, Australia has discovered that the in situ stress conditions in stiff to hard clays is directly related to pile installation rates, which in turn are a function of the piling rig capacity and ground conditions. With adequate and constant pile penetration rates in situ stress conditions in the stiff to hard clay are increased by about 40%, resulting in significantly higher pile capacities. If pile penetration rates are too slow the in situ stress conditions are reduced considerably by remoulding and shearing of the clay, potentially causing reduced pile capacities. The paper presents the results of full-scale test piles at a stiff to hard clay site installed using different full-scale piling equipment.INTRODUCTIONDrilled displacement piling (DDP) is a piling technique in which a hollow stem, fitted with a purpose built displacement tool at the bottom, is drilled into the ground. Dissimilar to non-displacement piles, like Continuous Flight Auger (CFA) piles or conventional rotary bored piles drilled with kelly bars, the soil is not excavated during the DDP penetration process, but is displaced laterally and to a lesser extent vertically. The cavity created by the drilling tool is filled with highly workable concrete during the extraction process. The DDP technique is very economical providing high production rates and creating only marginal drill spoil, which has led to its increased global usage during the last decade. The typical DDP installation process is described in Figure 1."

Jan 1, 1900

By Olgun

Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.

By Ambarish Ghosh, Subhaprasad Chakraborty

"Construction of basement floors has become necessary to meet the requirement of parking in office and residential complexes and in hospitals for radiotherapy treatment. Important projects coming up in Kolkata are mostly in closer proximity of residential buildings, office buildings and historical monuments. Sheet piling is mostly used as temporary shoring system during construction. Deep excavation in urban environment creates great problem related to construction induced vibration due to driving of sheet piles for basement, pile driving etc. which raises the chances of damage of adjacent buildings and nearby structures. Vibratory sheet-pile driving is the most common method of sheet pile installation. The knowledge of induced vibration due to this phenomenon is still very deficient. This paper presents the analysis of measured vibration data collected from different sites of Kolkata with varying soil profile. Typical two case studies of sheet pile and pile driving has been presented and the vibration values are analysed. The responses of the vibration are reported in terms of peak particle velocities (PPV). To evaluate the effects of vibration due to pile driving two aspects have been considered: the effect of the energy entering the ground from the pile and the effect of the soil condition.INTRODUCTIONIn urban areas infrastructure development projects are mainly located adjacent to existing structures like residential buildings, offices and historical structures. The construction work of such project influences the surrounding environment as well as human perception (Wiss 1981). During the construction of basement for residential complexes and hospitals sheet piling is mostly used as temporary shoring system or as to support the earth mass. The vibration induced due to driving of piles and sheet piles have been presented herein. Deep excavation projects close to existing structures increase the concern of environmental impact. For this reason the vibration assessment and prediction has become a subject of great interest. It is important to develop a site specific model for predicting the ground vibration resulting from pile and sheet pile driving at the construction sites. The developed model gives the efficacy to guide the engineer to select the construction methodology ensuring the safety of the surrounding structure. The model developed here is site specific and the parameters that has been used are dependent on the soil condition and the energy source."

Jan 1, 2015

By Massimo Poggio, Gabriele Balconi, Andrea M. R. Pettinaroli, Mario Ruggiero, Riccardo Castellanza

Grouting technologies are ground treatment techniques used for modifying the behaviour of a mass of soil or rock by injecting a mixture. The sleeved port pipes (also called Tube A Manchette) are highly diffused for grouting treatment of coarse soils and fissured rocks. This paper describes a combination of jet grouting and rock grouting with MPSP (multiple packer sleeve pipe) technique that has been used to realize waterproof curtains under fluvial structures for a cascade hydro-power plant. This is composed by five mini hydro-power plants, placed along the Iskar River, in Bulgaria, and composed by a penstock followed by the power house, a spillway, and an earth dam containing the reservoir. The geology of the site is characterized by an upper alluvial deposit lying over the bedrock. In each site, similar treatments were carried out: an impervious curtain along the plant section, obtained by executing jet-grouting columns in the surficial alluvial layers and grouting the underlying fractured rock by means of port pipes. The temporary embankment, built during the works for protecting each site from the possible river floods, has been waterproofed and stabilized by reinforced jet-grouting columns. The grouting processes have been controlled and monitored by a computerized system. INTRODUCTION The Iskar river cascade hydropower plant is situated northern of Sofia, Bulgaria, and it is composed by nine plants. Actually five of them have been built and produce energy. Each plant is composed by a penstock followed by the turbine building, a spillway, and an earth dam that contains the reservoir. The Iskar rivers runs in a narrow valley characterized by diorite or diabase rocks, with an upper deposit of alluvial soil, composed mainly by gravel and sand. Each plant requires an impervious curtain under the structures and in correspondence of the earth dam: this has been obtained by means of a jet grouting treatment of the alluvial coarse soil, and a grouting treatment with cement mixtures of the underlying rock using the MPSP technology. During the construction of the structures, the site has been shielded from the river water by a temporary earth embankment that has been statically improved and waterproofed by jet grouting columns reinforced with steel tubes; this allowed to work without interruption even in case of flood of the Iskar river.

Jan 1, 2019