Search Documents

By Babak Mamaqani, Pirooz Barar

The Heights project was located at Fashion Valley North, San Diego, CA. The scope of the project was to replace two existing commercial buildings with a large 7-story multi-family residential building. There was an existing 1:1 slope on the north side of the site. A permanent soil nail wall, 1,000 linear ft long, with a maximum height of 100 ft, was needed to replace the 1:1 slope at the north side of the project to accommodate the development. Previously there was a design for the permanent soil nail wall which required up to 115 ft long soil nails with large diameter rebars and 13 in. thick permanent facing. PB&A was engaged by the owner to conduct soil nail design optimization and value engineering to reduce construction costs and improve scheduling. First, the SnailPlus program was used to check the stability under static and seismic conditions and to design soil nail lengths and sizes. Then, soil nail head forces were calculated to design the permanent facing using FHWA recommended procedure. Another challenge of the project was to evaluate the interaction between a future San Diego Gas and Electric (SDG&E) tower and the soil nail wall. Finite element analyses were conducted with the PLAXIS program to ensure the deflection of the future tower would be within the acceptable range. The soil nail design optimization helped the owner to save approximately $800,000 in construction cost and improved construction scheduling.

Sep 8, 2021

By H. (Sam) Salem

A site investigation for a wide and tall hotel building, in the San Juan Bay area, Puerto Rico, indicated a soil profile of silty clay on sand, soft and loose enough to require piled foundations. The apparent uniformity of the soil profile across the site indicated that a single pile driving and termination criterion could be applied to the installation of the piles ? driven precast concrete piles. Because of the size of the site and importance of the project, the project also included a static and dynamic testing programme. The dynamic monitoring using the Pile Driving Analyzer (PDA) verified a consistent hammer operation. However, the results of the static loading tests showed significant and inconsistent variation in pile capacity between locations and little correlation between end-of-driving and restrike penetration resistances (blow-counts) and pile capacity. Therefore, it was not possible to rely on a simple depth and blow-count termination criterion for the site. In contrast, pile driving response in terms of measured reflected force and mobilized resistance coupled with CAPWAP analysis gave a reliable correlation to the results of the static loading tests. As presented in the paper, the dynamic testing programme was enlarged and used to develop and verify a complex set of termination criteria tailored for the multitude of conditions encountered across the site to achieve and ensure economical and safe pile installation.

Jan 1, 2008

By Eric S. Lindquist, Charles A. Luxford

The State of Texas recently adopted a master plan to expand the existing Capitol Complex in Austin. Phase 1 of this expansion will add two new State office buildings and five levels of underground parking to the existing Complex. Additionally, a landscaped pedestrian mall will be built atop a portion of the underground parking to enhance the area as a cultural destination. Capitol Complex website: https://www.tfc-ccp.org/ Brierley Associates was selected to provide detailed design of the entire Phase 1 earth retention system for an approximately 40-65 ft (12-20 m) deep, 500,000+ yd3 (380,000+ m3) excavation through overburden soils and limestone bedrock. To facilitate overall project coordination, all design packages were required to develop Revit models, including the retention system package. With the project located in an urban setting, this 3D model also facilitated coordination of the retention system with adjacent major structures and utilities. The retention system is a combination of soil nails, soldier piling with tiebacks and rock anchors with a shotcrete facing as a substrate for the below-grade blindside waterproofing system. Due to the substantial scope of excavation, a significant number of utilities had to be routed on a temporary span over the excavation. Brierley Associates designed this utility support structure, which required extensive coordination with the excavation support and existing utilities located directly underneath the structure’s foundations. Preconstruction geotechnical work identified a fault zone that might be encountered within the excavation; however, the fault feature was found to have a more adverse location and orientation than originally anticipated. This observation required that a portion of the temporary anchors be converted to higher-capacity, corrosion-protected permanent anchors.

By Zhang Wengang, L. John Endicott

The properties of many geological materials are variable. This is especially true for variations in elevation of the top of rock profile, strength of weathered rock, and conductivity of rock masses. Often the site investigation stage is completed by site specific ground investigation utilizing boring, sampling, and testing. Statistically this is a sampling procedure, but the borings are often widely spaced, and ground conditions between borings are deduced by interpolation. Often budgets are a limiting restraint and the information that is obtained may be less than desired. Sampling and testing is often biased. If claims for unforeseen ground conditions are to be avoided, the properties of the ground should be adequately identified. This paper describes how data can be used to evaluate the subsurface top of rock profiles, and can give insight into representative, maximum, and minimum strengths, and variation in conductivity relating to inflow of water into excavations, that can assist in planning the works and also in resolution, or avoidance, of disputes about unforeseen ground conditions. INTRODUCTION The mechanical properties of the ground are naturally variable. The work of Geologists, Engineering Geologists and Geotechnical Engineers is fundamentally investigative. Frequently, budgets for ground investigation are squeezed, resulting in widely spaced boreholes, with conditions between them determined by interpolation. Profiling can be adopted but the measurement, such as seismic velocity, is used as an indirect means of computing in-situ profiles and mass properties. Often a lot of test data are generated on large projects or by many projects in the same vicinity. Published data enlarge the database for a given project, and databases can be interrogated to gain insight into different categories of ground. Integration with geological studies can then lead to more reliable characterization of the ground in terms of identifying the materials present, their extent and their range of properties. This paper focuses on properties of rocks that are generally required for ground engineering, namely the top of rock profile, the unconfined strength of rock materials, and the mass conductivity. Data are obtained from Granodiorite and Granite in Hong Kong, and from Granite and the Jurong Series of weakly metamorphosed sedimentary rocks in Singapore. All four rock types have been tropically weathered, resulting in widely varying top of rock profiles, material strengths and mass conductivity. With a wide range in values for these parameters, project specific ground investigation conducted within a limited budget may run the risk of falling short of obtaining sufficiently reliable data sets, resulting in risk that unforeseen ground conditions may be encountered.

Jan 1, 2019

By Jeremiah M. Jezerski, Russell H. Lutch

The Mount Olivet Road Drop Shaft (MOR-DS) support of excavation (SOE) is a circular unreinforced concrete shaft with an inside diameter of a 30.5 ft (9.3 m) and depth of 120.5 ft (36.7 m), constructed using slurry wall methods. The SOE for the adjacent Mount Olivet Road Approach Channel (MOR-AC) and Mount Olivet Road Ventilation Vault (MOR-VV) near surface structures (NSS) consists of lean mix concrete walls and cement-bentonite walls, respectively, both constructed using slurry wall techniques and reinforced with embedded soldier piles. NSS SOE required multiple levels of preloaded internal bracing, with excavation depths of up to 75 ft (22.9 m). The original design construction sequence for the shaft and NSS SOE required that the MOR-DS be constructed in its entirety and backfilled to ground surface prior to excavation of the adjacent NSS SOE. After installation of the drop shaft and NSS SOE an accelerated construction sequence was implemented requiring the analysis of the excavation support systems to determine if the excavations could be open concurrently without adversely impacting the partially constructed permanent MOR-DS structure. The MOR-DS was analyzed using the finite element analysis (FEA) software, MIDAS GTS, to demonstrate that the unbalanced loads applied to the MOR-DS composite structure due to the revised sequence would not exceed the strength and serviceability requirements per ACI-350 or superseded by the more stringent project requirements. The results of the FEA were used to set limits for geotechnical instrumentation consisting of strain gauges located on the brace levels of the NSS SOE. A comparison of the SOE design hand calculations, FEA model results and instrumentation data is presented.

Oct 1, 2022

By Jørn Thomsen, Christoffer Brodbaek

"As governments increasingly accord high priority to sustainable energy, policymakers are finding that wind energy has a long track record as a proven alternative to conventional energy supply.Over the past two decades, wind turbine projects have been constructed offshore because of more stable offshore wind conditions and because there is more available space for large wind farms out in the open sea. Vindeby Wind Farm in southern Denmark was constructed in 1991. As the world’s first offshore wind farm, it provided valuable information and experience for researchers and designers that have led to new technologies and design improvements, a trend that will continue as more offshore wind farms are constructed. Today, the world’s capacity of the installed offshore wind turbines exceeds 1,000 MW. Most of these are installed in Northern Europe where there was early political support and favorable conditions, such as strong winds and relatively shallow waters. Offshore wind projects are now under development around the globe, including continental Europe, the U.K. and North America. ‘The largest offshore wind farm today is Denmark’s Nysted Offshore Wind Farm, which has a total capacity of approximately 480,000 MWh, equivalent to the yearly consumption of 120,000 households. It is five to six miles offshore in the Baltic Sea in the southern part of Denmark.The owner is a joint venture between DONG Energy of Denmark and E.ON Sweden. Bonus Energy (now Siemens) supplied the wind turbines, and P. Aarsleff A/S and subcontractors supplied the foundations. The contractor’s consultant, COWI A/S of Denmark, developed and designed the turbine foundations. With a total capacity of 165.6 MW, the project consists of 72 Bonus 2.3 MW turbines in water depths up to 33 ft. The turbines have a hub height of 226 ft, and the turbine blade diameter is 270 ft. The rotor and nacelle (the structure that houses the generator, gearbox and other equipment) weigh approximately 150 tons, and the weight of the steel tower is approximately 130 tons. The wind farm site is located in a relatively protected area of the Baltic Sea, but during the winter months, the water often freezes and the foundations needed to be constructed to resist ice forces. The founding soils at the site are overconsolidated clay tills with boulders and with a thin layer of softer surface sediments. Pockets of up to 30 ft of soft sediments were encountered, which required special foundation preparations."

Jan 1, 2009

By Thomas W. Scott, Manh N. Tran

Marine environments present a range of challenges for pile construction. This paper contains a discussion on the design and construction of marine piles for a recent Toll Shipping wharf upgrade in Burnie, Tasmania. The project involved several new structures including mooring, berthing and ramp dolphins supported by driven tubular piles with rock sockets, and an onshore mooring dolphin and ramp abutment supported by bored piles. Through the project, a range of construction challenges were experienced, including availability of tubular piles, the different penetration depths of driven piles into rock, the ability to drill out sockets when the piles were raked, the difficulty in verifying the design intent, latent conditions and ship impacts. The paper will present a summary of the different factors that influenced design concepts for the structures involved in the upgrade, and the challenges involved in the design of the structures. Following this, the paper will describe the methodology used to verify the design (including a pullout test), observations made during pile construction and lessons learned on how to limit risk throughout construction.

Nov 1, 2022

By Andrew R. Klaetsch, Peter W. Deming

"The Washington Avenue tunnel in Kingston, NY was completed in 1912 to convey combined storm water and sanitary sewage. Over a mile in length, the tunnel was driven almost entirely in bedrock, with the exception of an approximately 170 foot long brick arch segment constructed in soil. About 90 years after the tunnel was put into service, persistent subsidence problems and sinkholes were observed in Washington Avenue above the shield-driven soil tunnel segment, eventually causing the important traffic thoroughfare to be closed. Subsequent tunnel inspections revealed a breach in the brick arch and a significant volume of fine soil within the tunnel. A two-phase remediation program was implemented to control seepage, reduce soil migration, and remedy sinkhole problems. The first phase included in-situ soil densification by vibratory pile probe driving to improve density in shallow sandy soil loosened by ground loss. The second phase included installation of a continuous soilcrete arch structure over and alongside the tunnel, extending to rock or compact glacial till and spanning the length of the soil tunnel segment. Overlapping vertical soilcrete columns were installed through interlayered sandy and clayey silt by jet grouting to form a continuous arch structure, using grout parameters verified by full scale field testing.PROJECT BACKGROUNDThe Washington Avenue tunnel in Kingston, NY (Figure 1) was completed in 1912 to convey combined storm water and sanitary sewage to Rondout Creek by the Board of Water Supply of the City of New York. The tunnel is over a mile in length and constructed primarily in rock. Contract documents indicate the tunnel was designed with a horseshoe shape at least 3 ft wide and 5.5 ft high."

Jan 1, 2016

By Ryan T. Smith, Anthony Sahj, Alexander T. Darnell

Every second can count when trying to board a departing flight or catch a ride-share to your final destination. Hartsfield-Jackson Atlanta International Airport is in the midst of a project that aims to cut about 13 seconds between automated people mover trains (Plane Train) that move passengers between the terminals and concourses. The project involves extending the Plane Train tunnel west from its existing terminus under the domestic terminal. Working from inside non-public areas of the terminal, Keller North America, Inc. (Keller) incorporated systems of micropile-supported steel beams and grillage to both underpin existing columns prior to tunneling and support open-cut excavation at the tie-in of the new to the existing tunnel. Dewatering aided in mining a challenging section at the start of the drive of the mixedface, sequentially excavated tunnel and an automated instrumentation system monitored the performance of the construction and its impact to the terminal. Cut and cover egress and ventilation tunnels required braced support of excavation.

Oct 1, 2022

By Lance Rasband, Richard Hanke

"Seattle Tunnel Partners (STP) started mining on Seattle’s SR99 tunnel on July 30, 2013, working slowly through a 15 ft (4.6 m) thick fiber-reinforced concrete headwall. Once through the headwall, the machine would move through roughly 400 lineal ft (122 m) of jet grout-improved soil at a rate slightly over 6 ft (1.8 m) per day. It was anticipated that once through the improved area, Bertha—the world’s largest tunnel boring machine—would move at a rate of 35 ft (10.7 m) per day. By the end of October 2013, Bertha had mined roughly 430 ft (131 m), averaging 4.73 ft (1.4 m) per day, and had begun mining within native soils. By the start of December 2013, tunneling reached the 800 ft (244 m) mark and Bertha averaged 12 ft (3.7 m) per day, achieving as much as 42 ft (12.8 m) of progress on some days. However, on December 6, 2013, Bertha began to stumble and all progress quickly came to a halt. Preliminary InvestigationInitial reports stated that an obstruction had stopped the machine in its tracks. Malcolm Drilling received an early morning call on Sunday, December 8, 2013, from STP to rapidly mobilize a Bauer BG-50 drill rig with crews to investigate what was hindering Bertha’s progress. Malcolm’s equipment and crews flew into action and were completely mobilized and operational by mid-week. The preliminary investigation involved installation of 10 deep dewatering wells to reduce the hydrostatic head within the ground around the machine and allow STP personnel to inspect the cutter head from within the shaft for presence of obstructions. By the close of December 2013, the wells were installed and the dewatering system was fully commissioned. STP crews were then able to inspect the cutter head and found small fragments of a steel pipe wrapped around the outside of the shield. The steel was apparently from an abandoned 10 in (0.25 m) diameter monitoring well casing previously installed by WSDOT (Washington State Department of Transportation) to monitor groundwater conditions for the design and planning of this very project. After the steel was cut out of the head and cleared from Bertha’s path, she attempted to move forward but was only able to manage a slow crawl"

Jan 1, 2015

By Alex Grenoble, Alex Reeb, George Filz, Farzad Abedzadeh

"This paper summarizes available information on the characteristics and properties of deep-mixed soilcement produced by the wet method. The topics covered in this paper include: unit weight, unconfined compressive strength, strength variability for field mixed materials, influence of curing time, influence of consolidation pressure, Young’s modulus, differences in strength and stiffness between small and large samples, creep deformations, Poisson’s ratio, and tensile strength. In addition, this paper discusses the development of design considerations and recommended property values for a project that uses soilcement to protect an existing dam penstock from loads applied by an overlying stability berm. Some of the key recommendations for the deep-mixed soil-cement to be used in this project are that (1) a curved strength envelope that includes tensile strength can be used in the analysis, (2) the stress-strain and strength properties can be characterized using Duncan and Chang's (1970) hyperbolic model, and (3) a specification based on the median unconfined compressive strength value is appropriate.INTRODUCTIONFor many projects, including foundation and embankment support, deep mixing can be designed based on simplified procedures and following standardized guidelines (e.g., FHWA 2013). However for unusually complex or critical projects, it is often necessary to perform numerical analyses, and in order to perform these numerical analyses well, a thorough understanding of the material properties is needed.This paper summarizes information on the characteristics and properties of deep-mixed soil-cement produced by the wet method, and it discusses the development of design considerations and recommended property values for a specific project, herein referred to as the penstock project, that requires numerical analyses. For the penstock project, a horseshoe-shaped enclosure of soil-cement is being considered beside and above an existing dam penstock to protect it from loads applied by an overlying stability berm that will be constructed for seismic remediation. The concept is to use soilcement created by the deep mixing method along the sides of the penstock and to use compacted soilcement above the deep mixing to create the crown of the protective soil-cement zone around the penstock. For this application, the soil-cement stiffness, rather than its strength, is the controlling design parameter. To achieve the necessary soil-cement stiffness, the strength will be high enough that the factor-of-safety values against instability along potential failure surfaces passing through the soil-cement are high. Following conventional practice, the soil-cement acceptance criteria will be based on the unconfined compressive strength, and the specified strength will be selected to produce the desired modulus value."

Jan 1, 2015

By Michael Kynett, Francke Walberg, Richard Millet, Khaled Chowdhury, Mary Perlea

"Cutoff walls are the most common seepage improvement measure for levee flood control projects throughout California’s Central Valley. Cutoff walls are widely used because they can be implemented within an existing right of way in either heavily urbanized areas with limited access, or in high-value crop agricultural areas. The most commonly used seepage cutoff wall types are soil-bentonite (SB), soilcement- bentonite (SCB), and cement-bentonite (CB). Contract values for cutoff wall rehabilitation projects in the Central Valley range from several millions of dollars to hundreds of millions of dollars, and play a significant role in the reduction of flood risk in urban and rural areas. However, recentlycompleted construction of several levee improvement projects has shown limitations and inconsistencies among the commonly used technical specifications for construction of seepage cutoff walls. These limitations were evaluated by practicing engineers involved in different stages of cutoff wall design and construction. This paper describes the specification areas that typically generate design and construction issues. Recommended improvements to specifications are suggested to address these issues. The paper’s topics include: the applicability of the different types of cutoff wall materials and construction methods, quality control testing requirements, backfill gradation requirements, mixing procedures, and settlement criteria for backfill.INTRODUCTIONFlood control projects on the Sacramento and San Joaquin rivers in the Central Valley region of Northern California consist of a large system of reservoirs, bypasses, and levees. The thousands of miles of levees within the system were largely constructed and raised by local entities as need arose; this construction occurred prior to the development of modern design and construction techniques. The majority of these levees were initially constructed to protect land for agricultural development; however, a significant portion of these areas have become or will soon be urbanized. This urbanization has historically occurred in locations right up to the levee footprint. This expedient form of historical levee construction, when combined with adverse riverine geomorphology, urban development, and productive agricultural regions, has led to a levee systems with severe seepage performance issues in a real-estate-constrained setting."

Jan 1, 2015

By Shyam Chengalath, Johan Jeansson, Magnus Hörman

Down-The-Hole (DTH) drilling usually uses compressed air to power the hammer. However, there are now DTH hammers on the market which instead of compressed air use high pressure water to power the hammer. There are several benefits with using water DTH compared to air DTH, which are discussed in more detail in this paper. From a physics point of view many of the benefits arise from the fact that water is an incompressible media and air is not. Energy consumption is roughly a quarter compared to air, resulting in lower carbon emission and a lower energy bill. In the case of water DTH the water leaving the drill bit in the hole is at a low velocity and ambient pressure. However, with air DTH the air leaving the drill bit in the hole is at a high velocity and high pressure. This means that the risk of damaging surrounding structures in sensitive areas such as urban environments and dams, is greatly reduced with water DTH. In this paper two cases where water DTH is used in jet-grouting applications are discussed in detail. As these cases show there is a clear improvement in productivity when using water DTH hammers.

Sep 1, 2022

By Ali S. Fayad

"In June 2014, Orange County Flood Control District (OCFCD) completed construction improvements of the East Garden Grove-Wintersburg Channel for a price of $42 million. Instead of the pre-existing traditional trapezoidal levee, the channel was improved with a vertical compact levee. Dubbed Soil-Mix-Sandwich (SMS), this geo-structural and environmental solution for coastal channel improvements, underlain by liquefiable soil strata, was both a design and construction innovation. It employed Deep Soil Cement Mixing (DSCM) within the confines of a hydraulically-pressed (Giken Method) sheet pile duo. SMS was unique because it incorporated both subterranean and supra-dredge-line soil mixing within a very narrow workspace. Its DSCM pattern aimed at optimum densification of the workspace and was confirmed during the construction process. It availed the DSCM sub-contractor (Hayward Baker Inc.) the opportunity to demonstrate the fitness of their huge wet-mixing machinery within a very confined access-area and introduced approximately 70,000 cubic yards of DSCM within a limited 15 foot workspace width that stretched for a mile. The sheet pile duo created a construction-enclosure that became a stay-in-place load resisting system. PROJECT CHRONOLOGY AND LOCATIONAn Orange County Flood Control District (OCFCD) project-report was commissioned to study the East Garden Grove Wintersburg channel (OCFCD facility # C05). The report examined the hydraulic conveyance of the C05 channel and was concluded in 1994 by Williamson & Schmidt. The project-report did not encompass extensive geologic studies; but it provided several alternatives for channel improvement. It recommended a single row of sheet piles as the preferred alternative for the downstream reach.The most downstream reach of the C05 channel is located in an environmentally sensitive area, in City of Huntington Beach, California, USA. Its site includes seismic chasms that surface within the C05-footprint (the Newport- Inglewood tectonic fault). Extensive deposits of liquefiable soil exist beneath the channel. Furthermore, tidal-influence prevails against the channel levee. Implementation of a successful design for channel improvement emerged after several traditional concepts were deemed unacceptable by geotechnical consultants. OC Public Works (on behalf of OCFCD) was in need of a design and construction technique that mitigated many associated risks. From these circumstances, Soil-Mix-Sandwich was born and was referred to in the rest of this discussion as SMS. OC Public Works required the SMS design concept to undergo verification by independent geotechnical consultants. SMS chronology from conception to construction can be summarized as follows:"

Jan 1, 2015

By Filippo Maria Leoni, Alessandro Bertero, Gianluca Pianezze

"As part of the Southeast Louisiana (SELA) drainage program, designed by the U.S. Army Corps of Engineers (USACE) to reduce flood damages in the City of New Orleans and surrounding parishes through the construction of new pumping stations and better drainage canals, the SELA-22 project entailed the installation of a concrete covered canal along Jefferson Ave. and Prytania Street, in a highly urbanized portion of Uptown New Orleans, LA. The scope of the required soil improvement was to replace the soil between two parallel lines of sheet piles with a soil-cement mass to eliminate underseepage and provide structural support for the concrete culvert. The USACE selected the jet grouting (Jet Grout) technology for the construction of the bottom plug. The bottom plug is between 18 and 21.5 ft thick with a maximum depth of approximately 40 ft, for a total length of approximately one mile. The treated soil comprised soft clays and silts with occasional presence of sands. Project specifications required 100% area coverage, a 28-days unconfined compressive strength of 100 psi and hydraulic conductivity of 1x10-6 cm/s, to be verified by testing specimens from cored samples. The specialty geotechnical contractor proposed to accomplish the task utilizing their proprietary and innovative elliptical bi-fluid Jet Grout technology, and elected to perform a pre-construction bench scale laboratory mixing program to determine the most suitable grout mix features (i.e. binder type and proportions, binder content, etc.) to be applied in the subsequent field test and production stages. This paper will summarize and compare the results obtained from the different pre-construction and construction stages; interpretations of the data will be provided, along with general considerations regarding the effectiveness and significance of bench scale testing for jet grouting applications.INTRODUCTIONIn general, the effectiveness of the construction parameters in any ground improvement work depends largely on the physical and mechanical properties of the soil to be treated. Therefore, well designed laboratory and field test programs, aimed to disclose the interaction between the site-specific soils and the mixing parameters, are essential to achieve the desired end product."

Jan 1, 2016

By John A. Egan, Nathaniel Wagner, Micaela Largent, Jonathan P. Stewart, Debra Murphy, Jeremy Butkovich

The Millennium Tower is a 58-story reinforced concrete building that was constructed in San Francisco, California between 2005 and 2009. The Tower is founded on an embedded pile supported mat with pile tips bearing in dense marine deposits that overlie an over-consolidated marine clay layer known locally as Old Bay Clay. This clay layer experienced stress increases from Tower self-weight and from multiple episodes of de-watering between 2006 and 2018 at the Tower site and neighboring sites. Settlements of the Tower foundation have been measured since 2006 and lateral deflections of the Tower have been inferred and measured since 2009. Available information on this case history include geotechnical site conditions and data from a monitoring program that tracked foundation settlements, Tower tilt, groundwater levels at the Tower site, and ground inclinations over time. This presentation will discuss the ground deformation mechanisms that caused the observed movements, the degree to which the movements can be predicted, and lessons from this case history for the design of deep foundations for tall buildings in San Francisco and geologically similar regions.

Sep 8, 2021

By Gustav Jahner, Michael Baltrusch, Norbert Hoffmann

Near the port city of Whitby in the north-east of England, Anglo American (AA) is setting up the deepest mine in the UK, which will have a depth of 1,500m. The purpose of the project is to extract and transport polyhalite, both underground, and to market it globally. As part of the construction works, BAUER Technologies Ltd, the UK subsidiary of BAUER Spezialtiefbau GmbH, constructed three different shafts using the diaphragm wall technique, with depths of up to 120m. In order to ensure the specified vertical tolerance of maximum 200mm, several measurement methods were applied, and the results were documented in a 3D model. Complex de-sanding plant technology and specially developed polymer products were adopted to regenerate the trench supporting bentonite-slurry.

Sep 1, 2022

By Luca Pingue, Regine Jagow-Klaff, Franco Muratore, Carlandrea Albonico, Damiano Frontini, Rudolf Wernecké

This paper describes an artificial ground freezing (AGF) application carried out to ensure both watertightness and structural support for the safe excavation of four cross passages of the Forrestfield Airport Link (FAL) project in Perth. The line will deliver 8.5 km extension of the existing urban rail network connecting the growing eastern suburbs of Perth with the existing suburban rail network. The proposed soil improvement technique is adopted as a smart alternative to jet grouting from the surface since the use of heavy equipment with long vertical mast was not allowed due to the line underpassing an airport in operation. In this paper, details of the challenges and lessons learned during both design and construction phases are given. Furthermore, it is described the geometry and the installation of freeze pipes in presence of a massive steel frame, ventilation system and slurry pipes of the tunnel boring machine (TBM) in operation. It is also illustrated the web monitoring system to allow key personnel to follow in real time the development of soil temperatures, tunnel convergences and ground surface deformations as well as changes in the interaction between international parties involved due to the COVID-19 pandemic.

May 1, 2022

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By James P. Chivilo, Gregory R. Meeder, Scott J. DiFiore, Matthew H. Johnson

New construction in metropolitan areas has direct impacts on immediate neighbors and abutters. While noise and dust are generally nuisance concerns, demolition, vibrations, excavation, and dewatering can cause structural damage to adjacent structures. Different cities, states, or jurisdictions have different regulations that dictate requirements, roles, or responsibilities for varying parties during construction. The authors will introduce and discuss risks of new construction adjacent to existing structures, and the legal framework in Illinois which requires the owner of the new construction project to provide adequate protections for adjacent existing structures. The authors, who are engineers and attorneys, will discuss technical and legal concerns, and will highlight the importance of early and frequent communication among project participants to manage risks, despite whether or not any local regulations exist to drive the process. RISKS IN ADJACENT CONSTRUCTION New construction in metropolitan areas inherently involves some combination of noise, dust, ground-borne vibrations, earth excavation, and subgrade dewatering. These issues have potential to directly and adversely affect abutters and their property. Noise and dust can be nuisance concerns, while vibrations, excavation, and dewatering can result in damage to abutters’ structures. Noise and dust are unlikely to lead to physical damage to abutters’ property, and can be controlled with limited work hours and good housekeeping practices. Vibrations and excavations, however, if not well understood, planned for, and mitigated, can result in serious damage to abutters’ structures. In turn, this damage introduces additional and often significant costs and schedule delays.

Jan 1, 2019