Search Documents

By R. Brough

"Over 25 years ago, SKEGA pioneered the use of rubber linings in grinding mills and rubber is today widely accepted and almost standard material chosen for Regrind - and Secondary Hills. There are, however, only a few Primary Hills in operation with ""solid"" rubber linings because available materials and designs are often not cost efficient in comparison with steel alloys on a Cost per ton basis and/or downtime for liner replacement would be to a high.In other words, solid rubber has limits as any other material. However, 'SKEGA started to think, why not try to use the best properties of rubber as well as steel and combine the two materials together.Nearly 10 years ago SKECA started to test this concept in Rod Mills. A steel cap was vulcanized on to the leading face of the lifter bars, to be installed close to the feed end head (fig. 1)."

Jan 1, 1988

By M. Bueno

Between 1993 and 2003, a series of AG and SAG mill pilot plant trials were conducted using Hardinge Ical pilot plant scale SAG mills on numerous ore samples and ranging across a wide variety of operating conditions. The data from these tests were used to evaluate the design of SAG and AG mill circuits for over a dozen projects, of which about half were eventually constructed and commissioned. The data were also used in the development of SAG mill modelling, scale-up and simulation procedures by several consultants who had access to part of the data set. Recently, we have had the opportunity to bring this data together and further analyse the consolidated dataset. This paper reports on the outcomes of this analysis that has identified the impacts of different AG/SAG circuit flowsheets and operating conditions on energy efficiency and operating cost.

Jan 1, 2012

By K. G. Eriksson

"The first tentative test made to try rubber lining in grinding mills was made in the early twenties. However, because of poor rubber compounds and design the results did not prove to be promising.In the early sixties successful trials of rubber linings were carried out as a result of a cooperation between boliden AB and Skega AB.One of the reasons rubber was not used earlier for linings was the difference in wear characteristics between rubber and steel. The ability to successfully develop rubber mill liners depends on three factors:l. Design2. Material (rubber compounding)3. Experience (knowledge)DESIGNThe main difference between steel and rubber, in material aspect, is the elasticity and the low tensile and shearing strength of rubber. It is necessary to take maximum advantage of the elasticity and to reduce tensile and shearing forces by minimizing the sliding of the mill charge. This is accomplished by using the Lorrain type of liners, i.e., lifter bars and plates. It is, however, necessary to keep a certain balance between lifter bars to optimize liner life and grinding performance."

Jan 1, 1983

By Michel Gamache

This paper describes a system that manages and assigns vehicles in real-time in an underground mine. Each dispatching decision takes into account the traffic on the road segments of the mine network, whether bi-directional or unidirectional, and ensures that each LHD (Load-Haul-Dump Vehicle) arrives in the right orientation at loading and dumping points. Such systems can be used for two main purposes: 1) as a strategic planning tool and 2) as a real-time managing and optimising system for operations. Using a simulator in conjunction with the fleet management system, it is possible to accurately estimate the impact on productivity of decisions such as the development of waiting areas (bays, sidings), or the addition (elimination) of vehicles to the fleet in operation. Moreover, when used in for real-time dispatching, routing and scheduling of vehicles, the system can optimise production with respect to various assignment criteria such as minimising the cycle time or minimising the deviation from an optimal production plan. Dispatching, routing, and scheduling are handled simultaneously, taking into account the mine status, operational constraints, and all available information.

May 1, 2001

By Mary Jean Buchanan

The last twenty years have seen the advent of environmental concerns and sustainable development, and the industry has witnessed the rise of Environmental Management Systems and their registration through several international standardization systems such as EMAS and ISO 14001. Beyond EMS and ISO 14001, which new goal the mining industry should aim at. Life-cycle assessment (LCA), another tool from the Environmental Management System series, is also on the rise and currently the object of an international standard (ISO 14040:1997). Through LCA, it is possible to assess the environmental aspects and potential impacts associated with products and services, taking into account all the activities required for its fabrication, its use, its transportation and its disposal. How could LCA be applied to the mining industry ? Is the international market pressurizing on mining companies to supply an ?environmental ore?? What about the automobile industry and its use of LCA ? Will it influence the ferrous and non-ferrous metal industry, suppliers of raw materials ? This paper presents a review of possible applications of LCA for the mining industry as well as world trends.

May 1, 2001

By W. A. Grell

"The oxygen meter has been in use at MacLeod Cockshutt Gold Mines for over a year, At MacLeod about 200 tons per day of reground concentrate containing roughly 10% pyrrhotite and 20% pyrite is cyanided in four 181 x 18' Dorr agitators. A survey by the Department of Mines showed that oxygen content of some of the agitators was rather low. Experience with our oxygen meter indicates that the oxygen content must at times have been too low for good gold dis solution.We have found that in winter, when pulp temperatures drop to about 50° F, oxygen saturation in the agitators is not difficult to maintain. In summer, however, when pulp temperatures rise to 70or 75°F, the oxygen content will drop very readily. It was found that a high oxygen content can be maintained readily if the pulp is sufficiently dilute. Thus at 50° F, a pulp of specific gravity 1. 75 i.e., about 55% solids, will saturate; but at 70 or 75° F, the specific gravity must be decreased to 1 .45, equivalent to about 40% solids, in order to maintain saturation. Very thick pulps, such as thickener underflows, are noticeably difficult to saturate in the laboratory, and lose their oxygen rapidly.Clear solutions, on the other hand, absorb oxygen readily and hold it. The primary thickener overflow, before agitation, is 100% saturated; after storage of 3 to 4 hours it is still 100% saturated at re clarifier tank. Barren solution after spraying in a launder is 100% saturated.We have not yet attempted to determine what percentage saturation is necessary for good extraction, but it is known that there is a point at which extraction decreases rapidly. So far, the measures required to maintain over 80 or 90% saturation have coincided with measures required to hold the reducing power to the point believed necessary."

Jan 1, 1964

By J. D. Galloway

The mining industry of British Columbia continues to grow steadily in importance. The gross value of the production in 1925, sixty-two and a half million dollars, was a record, and ali indications point to the 1926 output registering a still higher figure. In an industry such as mining, where production means the depletion of known ore reserves, the discovery and development of new 'ore-deposits is of the utmost importance. To maintain and increase production, steady development is essential. In this respect, the record of the last three years in British Columbia mining is most satisfactory, as in this period more real development has been carried on than in any similar period in the history of mining in the Province. Prospecting, or the search for new ore-bodies, has also been fairly active, but comparatively few important new discoveries have been reported in the past few years. The mineral output of British Columbia consists of Iode minerals, coat and coke, and building materials. In 1925 the value of the output of these three classes of products was, respectively, about 46, 13, and 3 million dollars. The industry as a whole embraces the mining of these materials, and the treatment and manufacturing processes involved in preparing the various products for the market.

Jan 1, 1926

By Jiachen Wang

Longwall top-coal caving mining is one of the major mining methods for extracting thick coal seams in China. The top-coal caving longwall mining was began to use in the 1980s in China, and got the rapid development. The development of the top-coal caving mining technology in China, the achievements and the theoretical aspects progress of this method are described in detail in this paper. And the main technical model of China's top-coal caving mining is introduced in this paper. This paper also introduces the application of large-cutting-height mining in China and the technical level it has reached.

Aug 1, 2013

By C. F. Gleeson

"I HAVE BEEN ASSIGNED the pleasant task of adding a last word in way of summary to this session. I think that the trend set in having a geochemical session at the CIM Annual General Meeting is a good one and I hope it will continue so that members of the mining fraternity can get together on a regular basis and discuss geochemical problems peculiar to our Canadian scene. A series of interesting papers have been presented on what has been considered by many in the past as not only a problem area for geochemistry but even an impossible one. The papers should help dispel some of these fears. Lack of development of geochemical techniques in the Shield has been due to a variety of factors, many of which have been mentioned. However, I feel that one of the main reasons for this lack of development has been timidness on behalf of many people to get out and do the necessary work which helps produce answers to many of the questions asked. New developments and applications of geochemical methods in the Shield will not be done by the faint of heart but by those who have the curiosity, interest, imagination, drive, resources and, most of all, the intestinal fortitude to stick to it and not give up because results or conditions do not meet with preconceived notions. Another element that will be needed by those who will successfully apply the techniques and who will be responsible for new breakthroughs is the systematic approach to sampling and analysis and the integration of geochemical, geological and geophysical results. Erratic sampling patterns - a sample here and a sample there - generally lead to more problems than solutions."

Jan 1, 1971

By Hans Lundberg

Magnetic methods have been used for more than three hundred years in prospecting for magnetic ores. More recently magnetic methods have been used for finding salt domes and studying certain geological formations. A number of instruments have been developed and substantial improvements made as to their sensitiveness and accuracy. Papers and articles written on magnetic methods are generally elaborate and technical, and the average prospector finds it difficult to obtain the necessary information as to how to operate the simple magnetic instruments to the best advantage. The miner's compass, dip needle, and inclinator are, indeed, very useful instruments and are easy to handle, and a great deal of valuable information can be gained if the instrument is properly operated and the results correctly interpreted. The lack of knowledge of the fundamental principles, however, has caused a great deal of disappointment. Other and more elaborate geophysical methods have recently come into the limelight, and the prospectors seem to have lost a great deal of interest in the dip needle. This is much to be regretted, because magnetic methods have a particular field of use. The present article is an attempt to help the prospector regain interest in the magnetic instruments and to show the use and application of a simple magnetic survey. If the prospector expects some useful help in his work, he must, of course, know the instrument, know how to take the readings, and know how to plot and interpret the observations.

Jan 1, 1929

By Kimberly M. Curran

The path by which hydrogen supply is provided to any end use application will have a strong effect on the specific economics and price stability for the product supply and the flexibility with which it can be used. The objective of this paper is to present those variables which play a significant role in the selection of the hydrogen production technology, with a particular focus on several typical mining applications. The variables examined include gas requirements in terms of flow-rate and demand profile, overall volumetric consumption, level of interruption tolerable, gas pressure and quality needs. Also examined are the effects of geography in terms of primary energy supply available as well as existing hydrogen sources, developed or not. The role of these factors in the selection of an appropriate supply chain capable of supporting mining applications that use hydrogen as an energy carrier will be illustrated with a typical mining application scenario drawn upon in the form of a case study.

May 1, 2007

By Wataru Inagaki, Kozo Kawano, Tetsuya Ando

Cu–Ni–P alloys are the typical precipitation-hardening material. Thus, Cu–Ni–P alloys is expected to apply alternative materials for heat-exchanger tubes. Therefore, it was investigated that the effect of the heat-treatment simulated brazing on mechanical properties of Cu–Ni–P alloy in this study. The hardness of specimen as heat-treatment simulated brazing after solution heat treated (sht) was shown approximately 105 HV. The peak hardness and tensile strength of the specimen as performed aged at 498 K for 43.2 ks following the heat-treatment simulated brazing achieved at approximately 140 HV and 260 MPa, respectively. From these results, it is expected the application to higher-strength tube for heat-exchanger after brazing in a furnace. INTRODUCTION Copper prices have increased dramatically with high in recent years. At the same time, manufacturing industries are required to reduce the environment load by reducing the wall thickness of the copper tubes used in heat exchangers. High-strength copper alloys are developed for reducing the wall thickness, while achieving high strength, of the copper tubes. Moreover, excellent workability and corrosive durability are also required by these copper tubes. Furthermore, the brazing, which are carried out at about 1050 K during the assembly process of heat exchangers, leads to grain growth and re-solving of additive elements. Nomura et al. achieved a tensile strength and Vickers hardness of approximately 260 MPa and 110 HV, respectively, after aging at 723 K for approximately 36 ks. Tamagawa et al. studied that the strength of Cu–Ni–P alloy rapidly increased at about 125 HV during the cooling process after the heat brazing due to the Ni2P precipitates sized 5–10 nm. Furthermore, Inagaki et al. achieved a Vickers hardness of approximately 130 HV by aging at 498 K for 10.8 ks. In the present study, we focused on the lowest aging temperature of 498 K in the previous study, and investigating the effect of heat-treatment simulated brazing on the mechanical properties of the Cu–0.93 mass%Ni–0.24 mass%P alloy.

Jan 1, 2019

By R. T. Erskine

"IntroductionIn this paper it will not be possible to cover all details of the reagent systems at Brunswick Mining and Smelting but it is hoped that a description of the evolution of these systems will be of some benefit. The concentrator of Brunswick Mining and Smelting located near Bathurst, New Brunswick was originally designed as a 3,000 ton per day operation but before construction commenced was uprated, with 4,500 tons per day being treated by the summer of 1964. Development of the open pit at another ore body five miles away was initiated in 1965 and additional concentrator and crusher facilities went into operation in September, 1966. Present total daily throughput is over 8,000 tons per day. The ore at Brunswick is very high grade but mineralization is very fine grained and requires grinds generally over 75% minus 400 mesh for liberation. The amount of surface exposed using grinds of this order understandably requires great quantities of reagents, Reagent mixing systems for the original concentrator allowed only for batch mixing and were very expensive in labour cost especially.During the first three years of operation total number of men employed in reagent handling reached a peak of four men per shift and six men on dayshift unloading cars for a total of 22 men. At present only one man is employed on shift, and four men on dayshift take care of unloading and mixing reagents, a total of 8 men. The man on shift is almost entirely occupied with checking feeder operation, flow rates, and head tank levels. Most commonly used reagents are tabulated in Fig. 1 showing average monthly and daily requirements in the Brunswick operation as well as pounds per ton of mill feed as found in 1969. It is very obvious that with over seventeen tons each of lime and soda ash and six tons of copper sulphate used each day, opening of bags and mixing batches of solution is an inefficient undertaking."

Jan 1, 1970

By S. M. Moon

Today, underground exploration is spotlighted as an infinitely developable area. For this purpose, many tunneling technologies were created. And until this very day, many techniques are being developed for more efficient underground movement. Although previous technologies have been developed and now being used in various forms like TMB, struck propulsion method and hydraulic propulsion method, it is hard to find a robot type exploring in small scale. But development of small scale underground exploration robot is a promising research subject for its usage in examination of soil, mineral, and subterranean resources, investigation of hazardous regions, and the military. So we developed a robot that can dig and move underground, inspired from the motion of earthworm and mole cricket. Earthworm and mole cricket dig the soil in the front and draw it off backward, so that they can move forward. We developed a mechanism that uses 2 rotating solid of revolution (bits) for pulverizing the firmly united soil in the front and put it inside the body. The bits rotate in the opposite direction of each other. While moving forward, the soil in the front moves along the spiral on the bit and is saved inside the body. The soil saved inside is taken out through an outlet in the back by a ventilation system. The ventilation system on the ground blows through a hosepipe connected to inner part of the robot and the air blows off the soil. The moving mechanism of exploring underground can be classified into 2 parts. One is to fix the blade link on the soil in a form of 4-bar link. The other one is to move forward rotating the whole link. When the blade link system for movement rotates a certain degree, one blade link is fixed, while the other one is folded in. When 2 blade links of different length rotate as it is, different torque is applied on each link. By the law of action and reaction, the link that has larger torque leads the rotation and movement.

Aug 1, 2013

By Lindsay A. Robertson

The long term management of acid generating tailings at mine closure is a common issue, however, management of ARD is significantly impacted by local conditions, including climate. Acid generating tailings, over time, will produce acid rock drainage (ARD) if left exposed to water and air, which both contribute to the sulphide oxidation process. The long term closure of tailings storage areas is a concern from both environmental and engineering perspectives, with long term acid generation and dam stability the main risks. Several approaches can be taken to minimize ARD from tailings facilities using cover systems. Three tailings facility cover case histories, in areas of net positive water balances, were investigated using unsaturated flow modelling software to determine the long term potential for limiting ARD by increasing saturation of the tailings and decreasing oxygen ingress. Each case study demonstrates the importance of integrating the tailings dam engineering into tailings cover closure design. Model predictions are compared to measured saturation levels to assess the accuracy of the calculations.

May 1, 2011

By Chris M. Healey

"The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from underground workings returned extremely high values, up to 12851 g/t (375 oz/T) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.In the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/T) gave extremely good results. In the third case, however, indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results.The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this data base, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By William H. Emling

With profitability pressures in heavy industry increasing, many producers are turning to predictive maintenance as a means of harvesting untapped value from their production assets. Corporations are losing their maintenance and processing core competencies through attrition. As capital budgets are being trimmed, manufacturers are consolidating operating units into fewer, more profitable routes. Maintenance functions, however, typically receive low priority when investment is made, since many companies consider maintenance costs as ?overhead?. Condition-based monitoring, integrated to Level I and Level II process inputs, is seen as the most cost-effective solution to the implementation of predictive maintenance strategies. This paper will review the evolution of preventive and predictive maintenance programs, highlighting examples of successful application of integrated condition monitoring.

May 1, 2001

By Charles W. Villiers

AS is well known, there are large and valuable deposits of coal in British Columbia, both on the mainland and on Vancouver island. These deposits are widely distributed over the Province. The chief sources of supply on the mainland are found in the Fernie and Princeton-Nicola districts and on Vancouver island in the Comox and Nanaimo districts. The coals range from a very high quality bituminous coal to lignite. On the Upper Skeena river there is said to be a very large deposit of anthracite or semi-anthracite, but this field has not been developed. Coal was first discovered in British Columbia on the north end of Vancouver island in the year 1835, but it was not until 1852 that coal mining was seriously undertaken by the Hudson's Bay Company at Nanaimo, where mining has been carried on continuously ever since that date. The production of coal in the Province continued to increase until the year 1910, when the annual output reached its peak at 3,100,000 tons and a total of 7,800 men were employed in the industry. Since 1910, the production has dropped steadily until, in 1934, only 1,347,000 tons of coal were produced and less than 3,000 men were employed. This continued decrease in production has in no way been caused by lack of coal reserves. It has been due entirely to curtailment of markets. I do not propose to discuss coal mining practice in British Columbia, where we have all sorts of mining conditions, including submarine mining. There is no lack of coal supplies for either industrial or domestic purposes, nor is there likely to be any shortage of coal in the Province for many generations. We have our mining troubles, which increase the cost of production, but there are no insuperable difficulties to prevent the extraction of a large and increasing supply of coal. Our main difficulty-in fact our only serious difficulty-is to find a market for our output, and we must consider means which can be evolved not only to conserve our existing markets but also to expand them, at any rate within the boundaries of Canada. I will therefore confine my remarks chiefly to the all-important factor of Markets for our coal.

Jan 1, 1936

By W. P. Corking

"The purpose of this paper is to describe the relationship of the goldbearing ore to structure at the Pickle Crow mfoe. Information beyond this scope may be found in the reports and papers of Hurst( l), Bothwell(2), Thomson(3) , and Monette( 4).The property lies on Crow river, in Patricia district, 80 miles northeast of Allanwater, and about 125 miles northeast of Sioux Lookout on the Canadian National railway. From April of 1935, when the mill began operation, to the end of 1944, a total of 564,890 oz. gold and 49,275 oz. silver were recovered from 958,416 tons of ore.Mining on the property is at present carried on in two separate orebodies, the Howell and the No. 2 vein. Stoping has been carried on from every level on the Howell vein to a depth ot 2,450 feet below the surface and from several levels on the No. 2 vein through a mile long cross-cut on the 750-foot level to the Howell vein workings. A steadily increasing volume of ore is being obtained from the No. 2 vein.Each of the two orebodies consists of vein quartz with small amounts of other gangue minerals either in a single vein or a stockwork of veins. Both lie within sheared walls and carry gold in the free state. Fig. 1 shows the position of the veins with respect to the surrounding rocks. It will be noted that the delineation of the beds of iron formation shows that the lava flows and minor, interbedded sediments that make up most of the country rocks are areally folded and contorted.STRUCTURENearly all gold found to date in sufficient quantity and concentration to make ore in the Pickle Crow area is confined to these major quartz veins . Both strike a little north of east and dip north, and in both cases the attitude of the enclosing rocks is somewhat more north of east in strike and more steeply north in dip than that of the veins. As a result of this disposition both veins migrate across their enclosing rocks at a moderate angle in both dip and strike. (In this connection it should be noted that No. 2 vein dips at a considerably flatter angle than its host rock, but has a very pronounced rake to the northeast, effecting the same result as in the Howell vein.)"

Jan 1, 1954

By M. S. Ünal

Creation of 3D model of coal seams is a tedious and time consuming operation. Computer aided 3D solid modelling of coal seams can be performed in a fast and detailed manner. However, in case of having tectonically disturbed coal seams where faults may be observed, expert opinion is necessary to decide the geometry of the coal seam. The aim of this study is detection of fault zones with computers by using drill hole data. Firstly, a digital database is generated by using the drill hole data. Surface models of the layers are produced by applying triangulation method on coal seam roof elevations. The generated surface is divided into small squares and consequently dip and dip direction values are calculated for each square. Variograms for dip and dip direction are determined and maps showing the variation of dip and dip direction are generated by using geostatistical methods such as kriging and co-kriging. Examination of disconformities observed on estimation maps created by kriging and co-kriging clearly reveals the extension of faults. The method used in this study is applied to detect fault lines of a known mine field. 3D solid modelling of the coal seam has also been performed by using conventional cross-section method. The results of both methods were in good agreement. Identification of major faults by using the method introduced in this study could certainly simplify 3D solid modelling of coal seams.

Aug 1, 2013