Search Documents

By R. W. Pugh, S. L. Ma

"High carbon rods are typically used as the grinding media in rod mills. Usually an AISI I 090 grade of steel is used which provides the high hardness needed for abrasion resistance and sufficient toughness to prevent rod breakage.Work to improve performance in the past has mainly concentrated on increasing the hardness for improved abrasion resistance. This has been accomplished by adding alloys to the steel which uniformly increase the hardness across the rod section.However uniformly increasing the hardness of the rod produces a more brittle product and at high hardness l1evels can lead to rod breakage problems. Heat treatment processes can be used to selectively increase the surface hardness to high levels while maintaining the core at lower hardness levels to give a product that wears slower without breakage. AltaSteel has developed and mill tested a higher hardness heat treated grinding rodThis paper describes the development of a simple model to predict performance improvement with different hardness profiles and the AltaSteel heat-treated grinding rod process. Mill characteristics of the Endako operation are summarized and predicted performance improvements based on hardmess are compared to the approximate 25% achieved in trials running since July, 1991 at this mill. Early results of other mill trials are also presented.INTRODUCTIONAltaSteel, in Edmonton is a major supplier of grinding media. We have a strong desire to continually increase the quality and performance of our products and thereby improve the efficiency of our customers' processes. In the area of grinding rods, we wanted to produce a product with a significant improvement in wear rate. Second to energy, rod consumption usually represents the next highest cost in processing. This paper presents our development of a heattreated grinding rod that has reduced consumption by about 25% in trials to date."

Jan 1, 1993

By I. H. Redeker

North Carolina is the leading state in the USA in feldspar, mica, and spodumene production. Mixed feldspar, spodumene, mica and quartz are mined from hard rock, open pit deposits and recovered by flotation from the fresh pegmatite type ores. Potash feldspar, mica, clay and quartz are recovered from weathered decomposed pegmatites. The North Carolina State University has a Minerals Research Laboratory in Asheville with trained personnel and flexible pilot plant equipment. The flowsheets for the feldspar, spodumene and mica producing companies and for large phosphate and glass sand flotation plants were developed and tested in Asheville. Examples and problems of pegmatite flotation are demonstrated with flowsheets and slides.

Jan 1, 1981

By M J. Daniel

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

By A. J. Sinclair

"Abstract-Geology contributes essential information toward obtaining high-quality resource/reserve estimates. In this context, geology can be considered under the following overlapping topics: regional geology, detailed (deposit) geology, mineralogy, ore deposit models and continuity, with geological mapping being fundamental to all. Each of these topics is considered here in terms of potential contributions to "improved" mineral inventory estimation. Some of the principal conclusions are:1. Regional geological relations must be consistent with deposit geology. It is common that important geological relations are more clearly evident in various regional locales than in highly altered and/or highly deformed mineralized areas containing mineral deposit.2. Detailed geology provides information for a geometric model of a deposit, a model that serves as a basis for mine planning. It is important to distinguish fact from interpretation in such models. Substantial effort is required to characterize the geometric margins of a deposit and the relation of these margins to the simplistic geometric form that normally emerges as an interpretation.3. Mineralogical studies relate to many aspects of deposit evaluation including abundance of ore and deleterious minerals, spatial distribution of ore and deleterious minerals, grain size characteristics of important minerals, mill design, etc.4. Ore deposit models contribute substantially to confidence in developing a three-dimensional geometric model of a deposit for mine planning. Specifically, they are a basis on which to develop rules for interpolation and extrapolation of ore, and they contribute to recognition of domains, each with its own characteristic continuity and margin character.5. Continuity is dependent on mineralization style and may be controlled structurally and/or chemically. It is important to distinguish geological continuity and value continuity. A wide range of classical geological methods are useful in examining geological continuity; value continuity is best viewed as a statistical characteristic that is quantified by any of several measures of autocorrelation."

Jan 1, 1998

By R. B. Harkness

Many of us are familiar with the history of oil in the Province of Ontario, but for the benefit of those who have never heard the story I will repeat it. In 185 7 J. H. Williams, of Hamilton, an old-country Scotchman, who had the advantage of experience gained from the primitive methods used for refining the oil collected at seepages in Roumania, heard of the "gum beds" along Black creek in Enniskillen township, Lambton county. He erected a small plant in the bush and refined illuminating oil, where the village of Old Springs now stands. The labor of collecting this thick ?gummy substance from the sluggish water of the creek, prompted him to dig a well, the next year ( 1858), in the hope of obtaining a greater quantity. When his excavation reached a gravel bed on top of the rock, oil, resembling "lubricating oil of commerce", rose several feet. Several of these wells were dug and his refining business flourished. The following year the Drake well, in Pennsylvania, was drilled into rock, resulting in an oil find which encouraged one James Shaw to make a similar attempt on Black creek. With a spring-pole drill he completed his well in the spring of 1861 to a depth of 160 feet, and at that depth struck a gusher that flowed uncontrolled for several days. Great excitement followed and the village of Oil Springs had a mushroom growth. The Petrolia field was discovered in 1865. Lick followed up the Thames with a spring-pole rig testing the formations along that river and discovered the original Bothwell field in 1865. During the sixties wells were drilled in many counties in southwestern Ontario.

Jan 1, 1924

By M. Falutsu

"The PSI-200 is a rugged, innovative, and easy to install on-stream size analyzer. Its calibration is simple and can be done on-line, during operation. Two measurements are displayed on the panel, which are expressed as percent passing a selected size, or as any statistical diameter. These two measurements are given as two continuous 4-20 mA output signals. Operation alarms are displayed on the screen or are given as digital output signals.The PSI-200 has been used in various applications at Lakefield Research. Particle sizes ranging from 10 µm to 450 µm have been monitored successfully, with an accuracy of 1- 2%. Having the size measured continuously and reliably, optimum conditions have been established for the grinding circuit, resulting in a superior quality in pilot plant testing.INTRODUCTIONThe challenge of any operating plant is to optimize product quality, maximize throughput and minimize operating costs. The importance of particle size measurement at a grinding circuit is well recognized. Monitoring continuously the particle size and keeping the product as uniform as possible is crucial to the whole mill operation regardless of the nature of the operation.Various techniques and instruments have been developed over the years attempting to give reliable on-line size analysis data. The operating difficulties and the reliability of these equipment still present major drawbacks and none of them proved to be widely accepted.PSI-200 is a relatively new on-line analyzer. The operation is simple and of low cost and the maintenance required minimal. It measures particle size and it displays two parameters of the solids size distribution, either weight fraction of passing a certain size or any statistical diameter. Two analog outputs can be sent to a process control system and through a supervisory control loop the correct action can be taken to maintain the desired particle size (perhaps adjust the feed rate to the grinding mill)."

Jan 1, 1993

By R. Tipman

"In 25 years, processing of tar sand progressed from two small pilot plants to two major commercial operations owned by Syncrude and Suncor. These plants mine tar sand and extract the bitumen which is then converted into a synthetic crude oil. Considerable research on extraction of bitumen from tar sand has been undertaken by these two companies as well as other major oil producing companies, private individuals, universities and the federal and provincial governments. These studies have produced a number of alternate processing schemes which have yet to be commercialized. The producing companies are focusing their efforts on achieving increased processing efficiency, which includes improved bitumen recovery, reduced unit cost, energy conservation, and equipment reliability. In this review, the Syncrude process and examples of new process developments will be briefly described. IntroductionTwenty-five years ago, tar sand processing was limited to two pilot plants owned by Cities Service Athabasca Ltd., and Great Canadian Oil Sands. Earnest Manning was Premier of Alberta and was inviting proposals for the construction of a commercial tar sands plant. The invitations called for a much larger operation than those which had been undertaken in the past. All of the previous attempts at commercial operations up to 1960's had failed, largely because of a poor technical understanding of the process requirements, lack of suitable equipment, and lack of adequate capital. The previous record was not good. The pending new large scale plant was based on improved but not proven technology and equipment, which were developed from the pilot plant studies. In addition, the surplus of conventional oil in Alberta and low world oil prices were factors reducing the need for such a plant."

Jan 1, 1987

By R. J. McLeod

"Grinding at Giant Yellowknife is done in two stages. The first stage consists of two ball mills in closed circuit will: mechanical classifiers, the classifier overflow goes to flotation. The tailings from this flotation circuit are separated into slime and sand portions, the slimes go to an additional flotation circuit while the sand portion goes to the secondary grinding mills.Milltronic automatic sound control units were installed on each of the two primary ball mills and put into operation September 3, 1966. After about two months adjustments to the control units the operators were taken off the grinding circuit on November 1, 1966. The operators duties were taken over by the automatic control units while miscellaneous work was taken over by the helpers in the mill. The labour saving by the installation is approximately $2250.00 per month.After a short period of operation it was apparent there was a slight change in grind. The screen analysis of the primary classifier overflows for the period May to August 1966 averaged 62.23% minus 200 mesh while for the period September to December 1966 averaged 62.0% minus 200 mesh. This is a slight coarsening of the grind. The change in the primary grind has manifested itself also in the screen analysis of the final grind. Before automation the final grind was 80% minus 200 mesh, while after automation it was 7 5% minus 200 mesh. A change of grind was also noted in the flotation concentrates. Before automation the screen analysis of the concentrates was 35% plus 200 mesh and 50% minus 3 25 mesh. A ft er automation it was 35% plus 200 mesh and 47 .5% minus 325 mesh. In other words the grind got coarser or perhaps we should say there was less overgrinding. Another significant change took place in the assays of the slime and sand portion of the primary flotation tailings. It was usual under manual control for the slime portion to assay higher in gold than the sand portion. The reverse is now true."

Jan 1, 1967

By R. T. Seaman

There are several hydrometallurgical alternative processing options under development for high enargite and arsenic containing copper concentrates ranging from biological, atmospheric, medium temperature oxidation to total oxidative leaching. The most developed of these options is the CESL process boasting pilot campaigns totaling more than 8760 hours of fully integrated continuous operation, as well as, over two thousand batch scale oxidation tests performed on dozens of concentrates for flowsheet development. This paper reports the observed deportment of arsenic under varying arsenic, iron and acid oxidation conditions; it also describes the impact of iron to arsenic ratios and residue recycle on overall arsenic behavior and its stability in residue. INTRODUCTION The CESL Hydrometallurgical Process (CESL) was originally developed to compete with smelting of clean chalcopyrite concentrates. High Treatment Charges and Refining Charges (TC/RCs) combined with premiums on London Metal Exchange (LME) grade copper from onsite refining made treatment of copper concentrates using CESL a viable option at the time. As world demand for copper increased and a subsidized Chinese refining market developed, smelting contracts became more favourable for the miner and focus was placed on modifying the CESL Hydrometallurgical Process to handle concentrates with elevated deleterious elements. Dozens of pilot campaigns processing concentrates containing elevated concentrations of uranium, fluoride, mercury and nickel all led to further developments of the CESL Hydrometallurgical Process. In 2016 a United States patent was granted for a novel modification of the CESL Hydrometallurgical Process for recovery of copper from arsenic-bearing and/or antimony-bearing copper sulphide concentrates, Henry Salomon de Friedberg (2016). To date, over 2000 bench scale tests along with five fully integrated closed loop pilot campaigns, totaling over a year of online operation time, have been conducted processing arsenic bearing copper concentrates. This paper summarizes the observed behavior of arsenic under varying autoclave and process conditions.

Jan 1, 2019

By Bennett McLaughlin

The Penna Shaft is the deepest single?lift shaft in North America. AGNICO-EAGLE started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1 800 tonnes per day from a 2 240-metre deep shaft. Exploration success at depth lead to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7 000 tonnes per day. The use of another double drum hoist, instead of a Blair Multi-Rope winder, to hoist 24,5-tonne skips was only made possible by lowering the safety factor. This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of three kilometres.

May 1, 2003

By John G. Henning

Low quality rock is encountered in many manifestations in underground hard rock mines, ranging from weak and poorly consolidated rock to highly altered or foliated rock. Lateral mine developments driven in low quality rock pose on-going challenges to a mine operator, as ground stability issues, such as caving of under-supported ground, drift closure due to surface deformation or buckling processes, and degradation of exposed rock surfaces are a persistent concern. For many operators, ground support design is an iterative process, as support practices are refined with time. Using case studies from a variety of underground hard rock mines, this paper reviews techniques for the classification of low range rockmasses and examines the rationale and effectiveness of adopted ground support systems.

Oct 1, 2010

By Jianping Zhang

QUESTIONS: ?? Is it more expensive to find an ounce of gold in Canada today than 50 yrs ago? ?? Did the Canadian gold industry find more gold than they mined? ?? What is the future sustainability of the Canadian gold industry? ANSWERS: ?? The gold discovery costs in real terms only increased slightly from 1946 to 2000. ?? Though the Canadian gold industry mined more gold than they discovered in the period, when undeveloped deposits are taken into account, the deficit was merely 12 million ounces. ?? The Canadian gold mining industry would be sustainable in the foreseeable future, particularly, given the overwhelming predicted promising gold market in the mid/long run.

May 1, 2006

By Larry Urbanoski

"This paper describes the application of a radioisotopic energy dispersive X-ray aY1alyser to complete on-stream analysis in a base metal concentrator.The major components of the system are outlined and some description of the application, operating experiences and benefits are provided.IntroductionThe ma1n intent of this paper is to describe the on-stream analysis system in operation at the Geco concentrator. X-ray analysis systems installed in Canadian concentrators to-date may be broadly classified as wavelength dispersive analysers whereas the installation described herein is an energy dispersive x-ray analysis system. Energy dispersive x-ray analysis techniques may utilize radioactive sources to provide primary x-rays for excitation of elements and separate the secondary x-rays on the basis of energy levels. In contrast wavelength dispersive analysers apply high voltage x-ray tubes to provide primary x-rays and utilize crystals to disperse and thereby separate x-rays generated by bombardment of the sample."

Jan 1, 1978

By Mark Sherman

"One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client’s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques.Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt’s Grindpower and OMC’s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC’s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics.The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing.The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor’s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved."

Jan 1, 2012

By D. McFadgen

"THE Dominion Steel & Coal Corporation, through its subsidiaries, the Old Sydney Collieries and the Dominion Coal Company Limited, produces 4% million tons of coal annually from eight submarine collieries situated on the eastern coast of Cape Breton Island. The present workings have a frontage of 20 miles and extend 31/2 miles under the Atlantic ocean on gradients varying from 4 deg. to 24 deg. To date, some of the workings have reached .a depth of cover up to 2,800 feet.The pitching seams, the annual seaward advance, the resulting depth of cover and the rdatively soft roof and floor have necessitated the adoption of extensive longwall mining, with room-and-pillar mining con-fined to areas above the 1,000 foot cover line, where 60 per cent of the -coal is left standing in pillars to support the ocean floor. Longwall mining accounts for 87 per cent of the total production with the remaining outputs obtained from room-and-pillar work and the narrow work development. Seventy-four per cent of the longwall production and 41 per -cent of the room and development production is completely mechanized.Although 2 tons of water is pumped from the collieries for each ton of coal mined, the working sections are relatively dry as the heavy make of water is essentially surface drain-age from the land crop areas. The dry workings and the long haulage distances, which in many cases exceed 4 miles, have resulted in a continuing programme to combat the dust hazard, both at the working face and along the mine roadways."

Jan 1, 1960

By Ron Tessier, Claude Bazin, Robert Grant, Mike Cooper

"Grinding simulators are now widely available to assist in the optimization of industrial circuits. They provide circuit operating conditions or flowsheet designs that yield a given product size distribution. However, they do not provide information of the impact of a change of product size distribution on the subsequent flotation or leaching stages. This paper presents a method to predict grade and recovery indices for a flotation plant as a function of the flotation feed size distribution. The application of the method to various size distributions allows the determination of the optimal fineness of grind. A case study for a CuPb rougher circuit of a New Brunswick complex sulphide processing plant is presented to illustrate the method.IntroductionIs the grinding circuit product fineness optimum for the subsequent separation steps? This is a question that is certainly very difficult, but critical, to answer. Laboratory and pilot plant testworks can provide clues as to whether grind should be finer or coarser. For a full scale operation there is no other way than trying to change the setup of the grinding circuit and verify the effect on flotation. True effects can, however, be masked by the numerous and unexpected disturbances inherent to grinding and flotation circuit operations. A good preliminary investigation requires a noise free environment to elaborate possible solutions for the question.Plant simulators provide this noise free environment. However, despite grinding and flotation simulators having evolved significantly for the last 20 years, very little is available on the integration of both simulators to analyze the effect of fineness of grind on metallurgical performances. For instance, a grinding circuit simulator may help to find the tuning of a grinding circuit that will yield the desired fineness of grind, but does not inform on the effect the new product size distribution will have on the separation stages. Linking grinding and flotation would require a flotation plant simulator with the rate and infinite recovery parameters for each mineral in each size interval considered. This approach is seldom used because of the tedious work required to estimate the model parameters. Recently Leroux(1992) proposed a method to predict mineral liberation from grinding ore of known mineralogical texture. Although the method is still at its infancy it may provide, when combined with a reagent conditioning model (e.g Niemi et al., 1982; Bazin et al., 1988), a way to simulate flotation without the need of entering the numerous parameters of a flotation model."

Jan 1, 1994

By P. Czaja

The paper presents a patented and copyright protected concept of constructing a shaft lining that goes through rock masses having strong rheological properties and being susceptible to leaching. In the case of salt layers, especially at significant depths (over 900 m) the relative convergence of the heading contour may amount to 40 ?/year. That results in the fact that any other method of securing the shaft lining, e.g. by making it flexible, will not be sufficient to ensure the stability of the shaft reinforcement geometry. In the new shaft lining concept the excessive rock creep into the outbreak inside the shaft diameter will be removed by local and controlled leaching of the shaft cheeks by means of fresh water directed through a porous medium at the contact layer behind the watertight tubing lining. The paper presents the structure of such a lining and an outline of the construction technology. In order to implement such a lining, a typical tubing will be applied. Separate design and manufacturing will be required for the technological rings used to control the leaching process behind the lining.

Aug 1, 2013

By Ted Nuorivaara

The use of polymer-surfactant mixtures as foam stabilization agents is a topic that has drawn the attention of several fields but has so far not be thoroughly studied in the context of mineral froth flotation. The present work showcases a study on the impact on flotation performance of cellulose surfactant derivatives and their mixtures with commercial frothers. Bubble size and foam property measurements were run in a two-phase system along with laboratory-scale flotation experiments conducted using a porphyry copper ore from a mine in Finland. A comparative analysis on recovery, grade and flotation kinetics is presented on the products obtained using: i) a partially hydroxylated cellulose derivative (i.e. hydroxypropyl methyl cellulose; HPMC), ii) a commercial polyglycol-ester frother (Nasfroth240; NF240), and iii) mixtures of these two. The results show that using frothers with a total concentration of 30 ppm, the HPMC-NF240 mixtures provide advantages in terms of Cu recovery, (i.e., up to 95%), compared to the use of either NF240 (ca. 76%) or HPMC alone (ca. 1%). Interestingly, only a small proportion of HPMC mixed with NF240 was sufficient to produce a measurable increase in recovery. This improved performance was attributed to a synergistic effect of the polymer-surfactant mixture which further reduced the bubble sizes in a two-phase system compared to that of NF240. The present work offers a further step into understanding the phenomena taking place when a short chained surfactant is either substituted or mixed with a cellulose derivative, offering potential ways of exploiting this behavior for the enrichment of minerals. INTRODUCTION Froth flotation has been the predominant technology used to beneficiate sulfidic copper minerals such as chalcopyrite ever since it was invented in the late 19th century. The reason for the domination of flotation technology lies behind its versatility in selective separation as well as relatively cheap operational costs (Wills & Finch 2015). Even though flotation of sulfidic copper minerals is moderately well understood based on the broad research work done around the subject (e.g., Albijanic et al., 2015, Bournival et al., 2017, Wang et al., 2015, Mikhlin et al., 2015, to cite only a few), the modern era presents new challenges to the primary raw material industry, including questions regarding sustainability of mining operations accompanied by a need to improve the process efficiencies due to declining ore grades (Edraki et al., 2014).

Jan 1, 2019

By Balmer Neilly

Early in my term of office it was announced that my Presidential Address would make particular reference to the subject of Mine Taxation in Canada. With this purpose in view there was drafted a Balance Sheet and Earnings' Statement of a Gold Mining Company. This in turn was submitted to the Dominion Income Tax Authorities in Ottawa and to the Minister of. Mines of each of the several Provinces of Canada. The response to the invitation was not as complete as we had hoped it would be, but the figures that were obtained will be presented during the present meeting, and they constitute, I hope, a sufficient basis for extended study and additional enquiry during the year to come ( 1) . In the form letter that accompanied our request to have the submitted earnings assessed, I made the following assertion: "In this work we have three objects in mind. 1.--We will get direct comparison between the different Provinces in Canada. 2.-We will in this way educate our members concerning taxation as it affects the mining industry. 3.-We will publish the details as to how the assessment is calculated by each body, so that a Mine Manager in the most remote district will have a ready reference to guide him in his annual return to the taxing bodies. As things stand, there is no intention of making this a basis for a critical attack on the present rates assessed. It is intended as an authoritative summary of actual conditions as they presently exist".

Jan 1, 1934

By D. Milne

Laser profilometers exist for obtaining very accurate two and three dimensional profiles of joint surfaces. The application of this technology is not commonly applied to the collection of field data on discontinuity surface roughness. Rugged and portable field devices are not commonly used and the value of the possible field data that can be collected has not been well recognised. This paper reviews commonly used field techniques for assessing discontinuity roughness, discusses the value of this data and presents a new laser profilometer design for field application.

May 1, 2009