Search Documents

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By H. Ardehali, P. Lind

Many gold deposits also contain significant quantities of deleterious elements such as arsenic. Several biological pathways are possible for arsenic exposure; special care and caution must be used while undertaking metallurgical testwork on ores and concentrates that contain high levels of arsenic. Laboratory precautions pertaining to handling of airborne dust concentrations, necessary personal protective equipment, and effluent treatment are discussed.

Jan 1, 2014

By Emmanuel Henry

The Kiruna Mine, operated by Luossavaara-Kiirunavaara AB (LKAB), is a large-scale sublevel caving operation located in Arctic Sweden. Iron ore is extracted at a rate of 60 000 tpd from a four-kilometre long, 80-100 m thick and 60-degree dipping orebody. Actual production depth is 800 m under the top of the footwall and about 550 m under the average regional ground level. Because no support is left between the footwall and the hanging wall and despite the relatively low mining depth, extraction results in the formation of a huge stress shield modifying the original stress field and concentrating it just beneath the mining level. Effects of stress concentration on the rock mass are monitored through field observations and a seismic system. Severe stress-induced deterioration of openings is visible to a certain radial distance from the mining level: pillar crushing and fault slips are more and more common and extended. The seismic system, installed in collaboration with CANMET, confirms the field observations and completes them in the rock mass: fault slips and major seismic events are recorded. The system proves its effectiveness to outline the extension of the dynamic response of the rock mass, which actually seems much larger than field observations let think.

May 1, 2001

Abstract: ?The paper will review the perspective of Scotia Capital on financing mines, mining projects and mining companies in today's world of major increases in commodity prices, increases in capital and operating costs, shifts in foreign exchange rates, and increasing scrutiny of mining's social license ?Focus on debt financing alternatives Key Assumptions: ?Assume financing a mining asset (i.e. not an exploration play) ?Exploration is generally financed with equity ?private placements or public offerings on an idea

May 1, 2006

By G. A. Barclay

"I - INTRODUCTIONSteel castings still comprise the largest volume of wear materials used in crushing and grinding in the Canadian mining industry. The range of impact and wear properties possible with steel castings enables them to be used successfully in both high impact crushing as well as milling where abrasion resistance is the main criterion. Approximately 15,000 tons per year of steel mill liners and crusher castings are used by Canadian mines.The properties of the main steel casting alloys used - manganese, pearlitic chrome-moly and martensitic medium carbon steels will be discussed with reference to their applications. Field data on a new application in primary gyratory crushers for martensitic medium carbon steels is presented. Liner wear life and mill efficiency can be improved through proper liner design.The liner wear pattern can be used as an indication for liner profile changes to improve wear life. Changes in liner configuration can improve through put and use of larger castings can reduce downtime. Casting performance can be improved and foundry production costs reduced by adopting certain design improvements.II - ALLOYS USEDTable I list the most common ferrous liner materials used in relation to their hardness and wear resistance (1). The most wear resistant materials are the irons at the top. In many applications the service impact exceeds the impact strength of the irons and tougher less wear resistant steels must be used. The impact resistance improves from top to bottom with manganese steel the toughest. The hardness of the martensitic steels approaches that of the Ni-Hards however the wear life, because of the absence of carbides, is less."

Jan 1, 1983

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Thorium is frequently the main radioactive element in rare earth ores and is a resource that can potentially substitute for uranium. Thorium must be separated from rare earths in order to obtain products with low radioactivity. There are abundant resources of thorium in the rare earth ores in China, especially in Baiyunebo mixed ores. As an associated element coexisting in rare earth ores, thorium is, or can be, separated from rare earth concentrate, iron concentrate, as well as from waste water and slag to achieve recovery of thorium. The methods of separation include ion exchange resin, liquid-liquid extraction, and liquid-solid extraction. TBP extraction has been the main method applied to separate thorium by domestic and foreign scholars. This paper presents a comparison of different processes for the separation of thorium from rare earth ores, especially Baiyunebo mixed ores, single bastnaesite and monazite ore, and provides suggestions for the future recovery of thorium resources.

Jan 1, 2014

By A. Probst, N. Moores, J. A. Finch

"In 1994 McGill and INCO (Sudbury operation) initiated transfer of technology originally developed to detect level in flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud-line and solids load. The probe consisted in a vertical tube with 32 equally-spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth (so-called conductivity profile) from which the mud line and % solids could be inferred. The probe was installed in October 1994 and has been successfully detecting profiles since then. This communication includes a description of incidents and experiences during this technology transfer process including: probe installation and start-up; software modifications to accommodate operating conditions and operators' needs; calibration procedures to adjust to changes in performance as a consequence of long term use; and preliminary observations on the last stage, still in progress, signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.IntroductionThickening is one of the basic unit operations in mineral processing and hydrometallurgy used to separate suspended solid particles from a solid-liquid dispersion by gravity settling. As the dispersion enters the thickener, the solids settle and clarified water overflows the top. A thickener, which may be continuous or batch, is basically a large vertical cylindrical tank provided with devices to feed the dispersion and to remove the settled solids. The tank provides residence time for the particles to settle. The dispersion enters the thickener through the feedwell whose function is to dissipate the momentum of the feed stream and to create relatively quiescent conditions around the entering point. Rotating rake arms move the settled solids towards the discharge point located at the bottom centre of the tank.There are normally three distinct zones in a thickener: a top layer of clear water, a middle layer called a sedimenting zone in which particles are settling, and a bottom layer called a compression zone in which particles are pressed together as a consequence of the weight of accumulated particles. Proper operation of a thickener requires two simultaneous conditions: no solids in the water overflowing the top and the target solids content in the underflow pulp. To achieve these conditions is difficult because sensors for detecting the sediment line (interface between clear water and sedimenting zone) and the solids content in the compression zone are not commercially available."

Jan 1, 1998

By Melissa Whellams

?? What is a social risk assessment (SRA)? ?? Why do a SRA? ?? When do you do a SRA? ?? How do you do a SRA? What is a social risk assessment? ?? SIA vs. SRA ? SIAs determine how a company?s project will affect social/cultural conditions in a region ? SRAs determine how social/cultural conditions will affect the risk profile of a company?s project Social risk context includes: ? review of human rights record ? analysis of conflict situation ? analysis of political climate ? stakeholder identification ? stakeholder concern/interest identification ? And so on?

May 1, 2008

By H. M. Howard

"The subject of Grinding Media is perhaps still quite controversial. Many people will state today that the spherical ball is the only way, and also will state that this was settled long ago others are not so sure, and I am in this second category. Over the years there have been many changes in grinding and in our evaluation of grinding media we should always be ready to review the overall situation at regular intervals. There is quite a lot of inertia in all branches of Hineral Dressing and this is particularly true of grinding or, more correctly, comminution.In order to understand some of the things which are done today, and to understand some of the thinking on grinding, it is desirable to go back some sixty years and trace the developments in comminution. In doing this we should consider perhaps three general categories with respect to daily tonnage. An arbitrary division would be under 500 T.P.D., 500-5000 T.P.D., and large operations which might have several parallel units, each with a capacity of about 5000 T.P.D. For the future, in the broad picture, this last category will be the important one because we will be more and more dependent on large-tonnage low-grade operations for most of the metals of the future. Some such division is necessary because the daily tonnage will have a very great effect on what we can and cannot do. It is also necessary to consider the entire flowsheet, and to remember in particular that grinding is not merely to make small particles but is also a conditioning process, to prepare the materi.al for the process which follows. The relationship of crushing to grinding must also be considered. It is logical to include the liners as part of the grinding media and we should try to distinguish between the wear of grinding media and the consumption of media by corrosion. Finally, the whole question of grinding media should be examined in relation to the possibilities of using some form of autogenous grinding."

Jan 1, 1970

By E. C. Keeley

Some Safety Measures at Ontario Mines The following safety precautions have of late been taken by several of the Ontario mines: installation of water crossovers; washing clown of faces to show-up missed holes; insistence on gloves being worn as a protection to men's hands; wearing of safety boots and hats by underground men; and wearing of goggles by all men using hammers, starting holes, etc. In the summer of 1924 the Mclntyre mine began experimenting with means of removing powder smoke from headings by installing fans and pipe-lines of various designs, also with different means of introducing water into the air-blast when blowing smoke. By October of that year they had devised a scheme of water connection between the water and the air line, at a distance of about one hundred and fifty feet back from the face, using two valves and a short hose. By this means a limited amount of water could be introduced into the air which blew into the face, resulting in a fine spray of air and water combined. This spray not only helped to eliminate fumes but also introduced fine particles of water into the air, raising it above the dew point, with the result that when these fine particles of water settled they had attached to them fine dust particles, thus eliminating, to a great extent, the injurious dust caused by blasting. The combined air and water is turned on immediately after blasting and allowed to blow continuously for from four to five hours, until the muckers come on shift.

Jan 1, 1931

By Hal. Oliver

MR.]. G. TRAILL: My only excuse for contributing to the discussion on Mr. Hall's interesting paper is that I had the good fortune to be employed at Noranda during those romantic years, 1927 and 1928, when construction was at its height. The mine was in course of being rapidly prepared and brought into production, and the initial difficulties in crushing-plant and smelter were being met and overcome. They were stirring days, and perhaps those members who were with the second Empire Mining and Metallurgical Congress in 1927 sensed the atmosphere of excitement and activity that prevailed. Early History. Noranda must surely possess some of the most remarkable ore-bodies known to mining men, and the story of their development is pure romance. Ed. Horne's faith in the property, and the persistence of Thomson and Chadbourne, were richly rewarded in the end, but only after some very thin times had been experienced. In those early days access to the district was by the Kenojevis river and various portages to Osisko lake, on the shores of which the mine and smelter and the town of Noranda now stand. But all the early work was done on the Chadbourne claims, more than a mile to the west; through the b~sh. I have read a log of the events of that period, and through the whole tale of hard work, discouraging developments, occasional shortages of food, and constant danger from forest fires, can be read the faith and persistence of the men in charge. The Chadbourne ore was of that well-known type which, though just too low-grade to pay (with gold at $20 per ounce), is yet sufficiently encouraging to lead one on in the hope of striking something better. It was only as a last resort that work on the Chadbourne claims was suspended and a diamond drill brought to the gossan-covered hill beside the lake. The diamond-driller told me his version (it may be exaggerated) of how the position and direction of the first hole were decided on. He was told, "You might as well set up your drill here, and drill in, say, that direction". I believe that the first hole went through the richest ore ever found at Noranda. After the drill had gone through about 150 feet of solid sulphide ore running 17 per cent copper and 4 dwt. of gold per ton, it passed into barren rock, but the diamond-driller expressed the opinion (I wonder how he knew)) that the hole would come into ore again before long.

Jan 1, 1937

By C. B. Ndimande, C. Ntsele, M. Lisso, L. Arlow

"In the processing of UG2 platinum ore, stirred milling technologies are dominating regrind applications that require grinding the particles to P80s’ in the region of 45 µm. For this application stirred mills are 30–40% more energy efficient and require a smaller foot print compared to traditional tumbling mills. In this work a study was carried out using a batch pin mill and three scales of Stirred Media Detritors. A laboratory scale pin mill, a pilot scale Stirred Media Detritor with an installed power of 18.5 KW and two industrial scale Stirred Media Detritors in continuous operation, with an installed power of 355 KW and 1,100 KW were used. The industrial scale SMDs were in the secondary grinding section of a mill floatmill float (MF2) UG2 processing plants. The tests were focused on assessing the effect of feed rate and percent solids on power consumption and product fineness at lab scale, floatation response of the SMD product at pilot scale and on an industrial scale, the effect of feed rate on energy consumption and product fineness. The measurements obtained were feed flow rates, mill power and from the samples cut, particle size distribution of both feed and product. Specific energy was observed to increase with increasing percent solids over the 30wt% to 80wt% studied. Floatation response tests of the pilot scale SMD products show improvement in grade. Specific energy and reduction rations are observed to decrease with an increase in feed rate.INTRODUCTIONThe purpose of comminution in most mineral processing applications is to liberate the valuable minerals from gangue so that they can be recovered in subsequent separation stages. Most precious and base metal plants treat low grade fine-grained ores which require a higher degree of size reduction to yield the necessary degree of liberation (Partyka & Yan, 2007). Many authors have shown that the relationship between product size and grinding energy consumption is exponential, the finer the product from the comminution device, the higher the energy consumption (Gao & Weller 1993; Napier-Munn, Morell, Morrison & Kojovic, 1996; Jankovic, Valery & La Rosa, 2003). The suggested reason for this kind of relationship is that smaller particles have fewer flaws and higher strength than larger particles. Particles with fewer flaws and higher strength require higher energy for breakage to occur. One of the challenges most plants face is that of efficient energy utilisation in the liberation of the mineral from these complex ores. Conventional tumbling mills are not energy efficient in fine and ultra-fine grinding applications because some of the energy is spent on moving the charge and does not go directly into breakage. Stirred mills have been found to be about 30% to 40% more efficient and require a smaller foot print compared to traditional tumbling mills for regrind applications that require product size with P80s’ in the sub 45 µm regions (Radziszewski & Allen, 2013). Stirred mills are able to produce fine product because they can achieve a high number of stress events per unit time and volume compared to tumbling mills (Kwade, 1999a). To minimise energy usage without compromising product quality, the mining industry has adopted stirred milling technologies for fine and ultra-fine grinding (Radziszewski & Allen 2014; Kwade, 1999b). The south Africa platinum group metal (PGM) industry alone had over 40 stirred media mills installed by 2011 (Rule, 2011). Of that 40, 13 were in the ultra-fine grinding (UFG) application and the rest in main stream inert grinding (MIG)."

Jan 1, 2016

By P. M. Hedley

GOLD mining in Nova Scotia, as in any other gold district, has its own peculiar problems. Being in close proximity to excellent roads and to railways, and being blessed with good labour, the majority of gold mines in the Province find their paramount trouble is geological, namely, ore finding. After six years of continuous mining at Goldenville, the staff of Guysborough Mines, Limited, has collected many facts, has come to some definite conclusions, and has made a lot of guesses, some good and some bad. It is the purpose of this paper to set down such information as we have been able to gain in the hope that it may prove useful to other operators, present and future, faced with similar problems. What may be true of one Nova Scotian mine will not necessarily be true of another, so that the observations that follow should be considered as primarily applicable to Goldenville. Stated facts, conclusions, and theories are the result of the combined thought and effort of Head Office officials, of members of the Provincial and Federal Departments of Mines, and of members of the mine staff, past and present. Grateful acknowledgment is made to all.

Jan 1, 1941

By J. P. Mogan, E. D. Dainty

Polynuclear aromatic hydrocarbon (PAH) levels were measured in underground mines in the vicinity of diesel vehicles equipped with several types of emission control hardware. In general, the emission control devices appeared to reduce PAH levels, but the companion mutagen study suggested that the reduction might not always be beneficial. All underground PAH concentrations were below the threshold at which a significant impact on health might be expected, but recent animal exposure studies have indicated that PAHs may not be the primary hazard from chronic diesel fume exposure.

Jan 1, 1994

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By W. Kempson

"As has been noted on numerous occasions, the vertical shafts being sunk around the world are all tending to get deeper as we seek to take advantage of higher grades of minerals which can sometimes be found at greater depths. One of the challenges with these deeper shafts is the requirement to supply services to the mine’s operations at depth as well as the requirement to dewater the mine. Both the supply of water and the dewatering of mines is generally done using piping. With the greater shaft depths, this piping is now required to contain higher pressures as well as to accommodate changes in temperature resulting from normal mine operations. This paper will discuss the requirements for the design of high pressure piping in deep vertical shafts. The discussion will start with the general definition of the systems and the detailed design requirement. Once this is clearly outlined, we will discuss the options available for fulfilling these requirement as well as the advantages and disadvantages of each of the systems. We will finish with the installation recommendations and provide a basis for the maintenance of these systems. INTRODUCTION Piping in vertical shafts is used to provide a number of services in underground workings. These services vary depending on geographical location and the type of the ore body which is being mined. For example, in the Zambian Copper mines, one of the largest requirements for in shaft piping is for dewatering. Similarly in the Gold deposits in the West Wits basin as well as the deep level Copper deposits in Arizona, one of the largest uses for the piping is the supply of a cooling medium to underground workings to create a safe working environment (this can in the form of water or of glycol depending on the application). In South Africa, systems were installed which used the hydrostatic head which is generated from supplying chilled water to mines whose depths exceeded 2,000 m below surface. This chilled water was supplied as a closed system, allowing for high pressures to be generated which was then used to supply useful work (for example, Rock Drills, Face Cleaning and other ancillary services) whose power was traditionally supplied by compressed air or electricity. This system was initially researched by Chamber of Mine in South Africa. The design pressure range of these systems is 14 MPa to 18 MPa."

Jan 1, 2019

By Charles G. Kemsley

IN view of the truly remarkable development of special steels for special purposes, the mining industry has for years looked forward to a time when steel makers would come forward with a product which would be an improvement over the straight carbon steel which has always held the field for drilling rock. In order to avoid making changes in conventional shop practice, the industry has perhaps been too insistent upon obtaining a water hardening steel which could be handled in the blacksmith shop by long established methods. As early as 1932 or 1933, an oil-hardening tool-steel of the one per cent carbon, plus chrome, plus molybdenum type was applied to hollow drill steel. It was known as a hard as well as a tough steel, and one that, theoretically, should give a good account of itself as a rock drill, if properly heat-treated; and so it has proved in actual trials. There were numerous deterrents which retarded adoption of this steel. For several years there has been a constant improvement in the drilling qualities of the straight carbon steel, and, considering the higher unit price ? of the alloy, there has been considerable doubt in the minds of some mining? men as to what advantage there might be in the use of alloy over straight carbon for hollow drill steel. The alloy being an oil-hardening steel, its adoption meant having two kinds of steel in the mine, for a time, and that spelled trouble, unless some positive means of identification was adopted. The hardening and forging ranges of alloy steel being narrow also made necessary much closer control over these operations if poor results were to be avoided. These thoughts undoubtedly prevented its use becoming wide-spread, for, as a matter of actual record, less than fifteen per cent of all the hollow drill steel used in Canada today is alloy.

Jan 1, 1942

By Tatyana Alexandrova

The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Technological aspects of processing precious metal ores are examined in two respects: enhancing gold recovery from double refractory ores; and using carbonaceous ores on a production scale. The dispersed carbonaceous matter (DCM) present in concentrates causes the adsorption of [Au(CN)2]- complex on their surface during cyanidation process. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The problem of processing refractory (rebellious) gold ores is important for all the countries involved in recovering precious metals from ores. Depending on the degree of graphitization and the organic carbon content in DCM (including kerogens and bitumen), the technology used to recover precious metals varies considerably. The possibility of rare metals recovery, including rhenium, from black-shale rocks, has been examined. Comparative assessment of analytical methods of rare metals detecting has been carried out. It has been proved that neutron activation analysis is a promising technique. It has been shown that colloid-salt fraction (nanofraction) with particle size less than 1000 nm makes up to 3 wt% of black shale samples and is extracted by water under special conditions. The use of water instead of chemically active reagents provides insolubility of the mineral matrix and fully reflects the colloid-salt element of the samples. To sum up, the justification of the choice of technology for processing of carbon-bearing ores is based on examining the type of carbonaceous matter and its adsorption behavior. When the content of carbon of high degree of metamorphism is considerable, it is possible to recover platinum group elements and rare elements from this type of ores. The obtained results predetermine the general guidelines for creating new methods and techniques of processing carbonaceous material for integral development of solid minerals in the mining and oilfield areas of Russia.

Jan 1, 2016

By Jacob Wood, Robert Matusewicz

The Outotec® Ausmelt Top Submerged Lance (TSL) Process has achieved widespread commercial acceptance over the past 40 years for the processing of copper, nickel, lead, tin, zinc and precious metal bearing feeds. The continual development and evolution of the technology during this period has resulted in a more intense smelting process with higher energy efficiency and lower operating costs. More recently, considerable effort has been invested in decarbonisation of the process through improvements such as increased oxygen usage, dry feed injection and use of low-carbon auxiliary fuels. This paper covers a number of these recent advances to the technology and highlights their impacts on energy consumption and CO2 emissions for a range of non-ferrous smelting flowsheets. INTRODUCTION Relentless demand for improvements in the profitability, safety and environmental performance of non-ferrous smelting plants has driven a continual development and evolution of processing technologies in this industry. In response to these demands, a number of bath smelting technologies have emerged over the past 40 years and have been implemented for the treatment of primary and secondary feedstocks. The Outotec® Ausmelt Top Submerged Lance (TSL) Process (henceforth Ausmelt Process) is one such bath smelting technology which has been widely adopted in a large number of greenfield projects and brownfield plant modernisations (Wood & Hughes, 2016). Emissions of CO2 from the production of non-ferrous metals represent approximately 4-5% of global totals (Rankin, 2012), comparable with the almost 10% attributed to iron and steel production. Despite significant improvements in the energy efficiency of modern smelting technologies (Coursol, Mackey, Kapusta & Cardona Valencia, 2015), primarily through increased oxygen usage, further innovation and development is still required to address their reliance on fossil fuels such as coke and coal. Transformation of the non-ferrous smelting industry to low-carbon technologies and process flowsheets is lagging behind the power and transport sectors, which have witnessed significant growth in clean/renewable energy technologies to reduce CO2 emissions and address the issue of anthropogenic climate change (IRENA, 2018; IEA, 2018).

Jan 1, 2019

By R. Bridge

Mining companies are progressively finding themselves having to develop operations for more complex, deeper ore bodies, which require the use of more complicated mining and mineral processing methods. This coupled with the generally increasing trend of higher capital and operational costs have led to a need in the industry for improving ore body knowledge, mining and mineral processing. Geometallurgy is a relatively new concept that can link the three aspects, and when used effectively it is a method that can produce the necessary information for designing and building operations for reliable and optimum performance. Geometallurgy not only involves the integration of geological, mining, and metallurgical fields, but it can also be expanded to include environmental and economic information to produce a block model that can be used to obtain the best outcome in terms of plant response and plant sustainability. The geometallurgical program should not end once the block model has been populated. A detailed geometallurgical approach should be applied to all stages of the operation encompassing sample selection, through to equipment sizing and production forecasting. It can also become a useful optimisation tool thereby allowing the operation to be proactive rather than reactive against changes in the ore characteristics. With the development of metallurgical performance predictors it is possible to quantify how the ore will behave in the process plant in terms of throughput, recoveries, reagent consumption, etc. Therefore, in terms of responsible mining and sustainable resource development, a geometallurgical approach to operations is the logical step for plant development. In this paper we describe the state of the technology with respect to the application of geometallurgical modeling and its utilisation in the fields of design, forecasting and optimisation of mining operations.

Aug 1, 2013