Search Documents

By G. Lafont

Aug 1, 2013

By Yan Qun, Chen Xiao-ming, Ma Pei-long, Luo Xian-ping, Luo Cai-gui, Feng Bo

The effect of leach promoting reagent LPF on the leaching process of a weathered crust elution-deposited rare earth ore has been investigated and the mechanism is discussed. The result shows that the leach promoting reagent LPF can enhance the leaching extraction of rare earth ore effectively. With the addition of LPF to the lixiviant at a concentration of 0.1%, the leaching extraction increased by more than 8%, the ammonium sulfate concentration could be decreased by 25%, and the leaching liquid/solid ratio reduced by 34%. The mechanism analysis shows that LPF can react with rare earth ions and form soluble coordination compounds, thus reducing the activity of the leached rare earth ions, increasing the concentration difference for ion diffusion, and promoting the rare earth leaching process. These results will hopefully help point to a new approach to making the leaching process of low-grade weathered crust elution-deposited rare earth ore more efficient and with lower lixiviant consumption.

Jan 1, 2014

By Tyson C. Birkett

Initial indicator mineral sampling covering 425,000 square km of northern Quebec and subsequent follow-up of positive results convinced the Ashton ? SOQUEM joint venture to acquire mineral rights to 380,000 hectares prospective for diamond in late summer, 2000. Drilling in 2001 and 2002 identified eight kimberlitic bodies, all significantly diamondiferous. Commercial size stones (retained on a square mesh sieve with openings 0.85 mm) and encouraging grades have been returned by several bodies tested to date: The Renard bodies are formed by steep-sided breccia pipes with kimberlitic matrix surrounded by irregular outboard breccia zones within country rock. These bodies were emplaced in high-grade metamorphic rocks of the Superior Province of Archean age. Orthogneiss with lesser tonalite hosts the breccias, although regionally paragneiss is also present. Diatreme facies portions and nearby country rock are intruded by minor to major (Renard 1) amounts of hypabyssal-facies kimberlitic rock. Renard bodies are macrocrystic, with large olivine crystals set in a groundmass of olivine, phlogopite, monticellite, spinel, carbonate, apatite and serpentine. Proximity of various Renard bodies, with most in a core area of 0.5 square km will allow planning of an efficient mining operation. Geophysics, especially magnetic surveying, has contributed to identifying bodies of kimberlitic rock.

May 1, 2003

By L. Kilpinen, K. R. Kay, H. B. Fowler

"FOREWORDThe International Nickel Company of Canada has built four ore concentrating plants since 1950. The fifth and largest is now under construction. In each successive plant, the level and type of instrument control and sophistication of control techniques have increased as experience was gained. The type of control progress is illustrated in Fig. 1.At Frood-Stobie the high degree of instrumentation and the level of control were made possible by the constant evolution of techniques and improved instrument hardware technology. We have established in practice concepts that are sound, although many modifications to instrument sensor types and locations 1-rere often necessary. It is generally true that at other existing Inco mills, it is possible to run ""all manual"" for protracted lengths of time because of operator availability and dependence. The Frood-Stobie Mill is the exception, and it is the degree of reliability of the instrumentation hardware and level of maintenance that has made this possible."

Jan 1, 1971

By G. W. Diehl, G. A. Griffiths

"Gentlemen, one week ago, I attended the University of Minnesota's Annual Symposium on Mining, in Duluth. A good part of this symposium was dedicated to mill linings of rubber.At this symposium, three mining companies published results from long time full scale tests with rubber linings in mills at four different mines. These were the Republic and Empire Mines of Cleveland Cliffs Iron Company, the Groveland Mine of Hanna Mining Company and the Eagle Mountain Mine of Kaiser Steel Corporation. These papers will be printed in due time and I will not endeavour to relate their full contents, let me only say that in three of the plants, the linings were found to be very economical compared wi.th steel, and that these three are converting over completely to rubber linings, while the fourth, Empire Mine, reported no economical results as far as the shell lining goes, whereas the grates showed promise of becoming economical. The authors of the Cleveland Cliff's paper, however, stated that design improvements in the rubber lining possibly could result in an economical lining also for Empire Mine.That rubber linings in mills, in most cases, show better wear life than steel linings, is known by most of the audience. But, one thing that has not before been disclosed by the endusers is the effect of rubber linings on the grinding economy. All three papers mentioned above reported no change in capacity or grind and two of them reported a decrease in power consumption per ton ground. Hanna Mining reported an average decrease over a three year period for one mill of over 10%. This, of course, puts the economy of a rubber lining in a completely new light. Finally, a point of interest at this meeting was that all three papers emphasized the design aspect, Thus the industry has acknowledged what I believe to be a very important fact - the design of a lining is often more important than the material it is made of."

Jan 1, 1970

By P. J. Oakley, W. M. Thomas, S. W. Kallee, D. G. Staines

A Friction stir welding (FSW) is now extensively used in aluminium industries for joining and material processing applications. The (FSW) technology has gained increasing interest and importance since its invention at TWI almost 15 years ago. The basic principle, recent applications and the continuing development of the FSW technology are described. The paper will introduce some of the variants of FSW, such as Dual-rotation, Twin-stir(TM), and the Stir-lock(TM) technique.

Jan 1, 2006

By S. A. Kenzap

This paper provides an overview and discussion of key aspects of operating risk valuation in underground metal mining systems, with impact on project economics, using stochastic computer modelling in Discounted Cash Flow (DCF) analysis. Mine operating risk classification and assessment for ground, equipment and scheduling aspects are presented with an overview of available risk valuation tools that have been developed in engineering disciplines. The classification is organized by keeping in perspective the mine design needs and constraints, as well as the potential economic impact that operating problems can have on an underground development and production system. These sources of cost, revenue and time delays are tabulated to enable the hierarchization of potentially hazardous unplanned events occurring during the mining project life cycle. In complex technological systems, like the underground mining systems, the decision-making process involve a wide range of uncertainties, and often this is based on subjective and qualitative expert evaluations. Whether a qualitative or quantitative analysis is conducted, it is often the case that the probability of a certain project parameter value needs to be estimated. This requires use of methods and techniques to handle subjective, qualitative measures and to combine them with quantitative stochastic modelling in order to evaluate mine operations-related issues on DCF economic performance measure parameters. Links are established between decision making and the risk-based mine planning process for evaluation of design alternatives, with emphasis on the need of introducing flexibility in mine design. Finally, challenges of risk-based mine planning and design implementations are discussed and the call for an integrated risk-based real options systems valuation (ROV) ?in? projects analysis is made.

Aug 1, 2013

By P. Reyes

The Codelco Chile El Teniente Division Caletones Smelter has an objective to smelt 1,250,000 tonnes per year of copper concentrate. This is a great challenge for the smelter facilities and particularly for the acid plants. The analysis ensuring that there are no obstacles to achieve the production capacity was of great importance. Therefore a series of activities were undertaken as well as studies dedicated to reach the target. This paper presents work focused on a fluid dynamic study, translated in an operation methodology of integrated handling of the smelting and converting gases with the objective to optimize the gas flow and S02 concentration. The optimization should be done employing the current installations, equipment and instrumentation and/or minor modifications. In the first part of the work the condition of the instrumentation involved in the gas handling was checked, improvements determined and the corresponding corrective actions were carried out. The proposed operation method consists of operation of the Cleaning Gas Plant 2 (TC' s gases) and operation of Gas Cleaning Plant 1 (the remaining gas plus the gases from CPS). The implementation of the operation method involves the modification of the valve of the gas into the duct to plant 1 from On to Off to modulate flow. After modification a three days test was carried out. To evaluate the tests, a "Sulphur Capture" indicator was used. During the test the behaviour of the effluent treatment plants was closely examined. No problems or unusual operating conditions were observed. The reduced flow of gas to Gas Cleaning Plant No. 1 permitted the start up of the 2nd test day treating most of the gas received by Gas Cleaning Plant No. 2. The operation was carried out with the limitation not to increase the effluent pond level, which was maintained constant.

Jan 1, 2007

By Sean Junor

Cameco Corporation ?One of the world?s largest producers of uranium ?Operations in Saskatchewan, Ontario, the United States and Kazakhstan ?Development projects in Australia ?One of the best employers for Aboriginal Canadians Geographic location ?Remote or northern operations ?Northern Saskatchewan ?Residents of Saskatchewan?s north (RSN) ?Wyoming ?Nebraska

May 1, 2010

By T. Moyo

Ammoniacal solutions are attractive and effective lixiviants for the dissolution of chalcopyrite, allowing for the formation of stable ammine complexes with copper while rejecting iron. Chalcopyrite dissolution in ammoniacal solutions is reviewed from literature, and results from a recently completed study evaluating it through electrochemical and controlled leach studies are discussed. Ammoniacal leaching of copper ores dates back to 1916 in the leaching of low grade copper ores in the Kennecott leaching plant and in the Calumet and Hecla mines, followed by the commercialisation of the Sherrit Gordon process for the ammoniacal leaching of sulphide copper ores in 1948. Since then ammoniacal leaching has received intermittent focus from researchers with the development of the Anaconda’s Arbiter process and the unsuccessful Escondida process. In these leaching processes, the formation of surface deposits has historically been reported to result in the passivation of the chalcopyrite surfaces, whereas oxygen mass transfer in solutions has been the focus of process design improvements. Results of studies on high grade chalcopyrite material is presented in this paper which show that although a surface deposit was formed, it did not result in the passivation of chalcopyrite in ammoniacal solutions, and that while oxygen transfer is critical, it is not the direct oxidant in the reaction. INTRODUCTION Ammonia and its salts have been used in the hydrometallurgical treatment of non-ferrous metals such as copper, cobalt and nickel from oxide ores. Its chemistry allows for the selective dissolution of desired metals, leaving behind gangue including iron. Chalcopyrite is a copper sulphide ore known to be very stable and hence recalcitrant to many hydrometallurgical processing methods. Thus, the dissolution of chalcopyrite continues to be an attractive area of research. The dissolution of chalcopyrite in ammoniacal solutions is possible due to the stabilisation of copper(I) and copper (II) ions by ammonia in alkaline media. Ammonia has become more attractive as a lixiviant during the present socio-economic climate due to its low toxicity, relatively low cost and ease of regeneration by evaporation (Meng & Han, 1996). Ammonia processes are ideal when the gangue minerals are acid consuming e.g. with calcareous or dolomitic gangue (Paynter, 1973).

Jan 1, 2019

By M. Mahdi, L. So, A. MacMillan, D. Metcalfe, J. Woloshyn, D. Sauter, N. Uys, JP. Janse van Rensburg

For city smelters, with limited real estate, efficient slag cleaning furnaces followed by water granulation to produce an iron silicate product is the preferred process approach. Water granulation, however, consumes large volumes of water and requires high maintenance due to abrasive slag/water slurries. Air granulation offers an alternative to water granulation, which eliminates water use and has low maintenance requirements. Although full-scale operation has not been implemented for copper slags, full-scale operation for platinum group metal (PGM) converter slag has been implemented. A review of full-scale air granulation performance for PGM converter slag is provided. Based on PGM converter slag granulation performance, parallels to copper slag granulation are drawn and full-scale operation for copper slag is modelled using computational fluid dynamics (CFD). INTRODUCTION Typical slag management practices in the copper industry include dumping, slow air cooling, and water granulation, as shown in Figure 1. Dumping is the most commonly used slag handling method for most metal production plants, but presents challenges including the requirement for a large slag pit, requirement for expensive/high-maintenance “hot” mobile equipment, risks associated with transportation of molten slag, and no value recovery from slag as a sellable by-product or from slag as a source of heat.

Jan 1, 2019

By Joseph Bradley

THROUGHOUT this article, minerals used in the paint industry are designated 'pigments'. They may be classified in two groups: (1) Pigments which are used in the state in which they occur in nature, requiring only mechanical preparation. (2) Pigments which require heating or chemical treatment before use, in order to obtain from them a product of the desired quality or shade of colour. They may be further classified according to colour, as follows: White Pigments .-These include calcium carbonate (chalk, marble), gypsum and alabaster, kaolin-or china-clay, and magnesia. However, the white pigments most extensively used are compounds prepared chemically from minerals containing lead, zinc, titanium, and antimony. The white pigments are of particular importance because, not only are they used by themselves, but they also serve as adjuncts to other colours for the production of special shades. Yellow Pigments.-These are mainly naturally occurring ferric hydroxides, as limonite and bog iron ore, or similar. compounds prepared artificially. Brown Pigments .-Pigments of this group are distinguished for their beauty and depth of colour, and many of them are used in the finest of paintings. Familiar names are sienna, umber, and Vandyke brown. They are for the most part ferric hydroxides, containing varying amounts of water; but the group also includes a manganese brown, which consists chiefly of a mixture of oxide and hydroxide of manganese. Red Pigments.-Chief among this group is ferric oxide, known under various trade-names, such as Canadian red, Persian red, etc., and also the much prized and somewhat rare vermilion. The pigment used is either naturally occurring hematite, de-hydrated limonite, or artificially produced red ferric oxide.

Jan 1, 1937

In the last 30 years numerous mining plants have been developed in North America but only a handful of these have required freezing the area where the shaft was sunk. The most recent mine shaft to be sunk using this technique is located on an island off the coast of Louisiana. The project required the input and skills of numerous people in several companies, including the owner, engineers and contractors. The Cote Blanche installation is one of several mines in the area which extract salt from a dome which extends under the Gulf of Mexico. The geology of this area is, however, markedly different from others in the region because there is approximately 460 ft of water logged soil above the salt dome. Because it is not possible to sink a shaft in ground that is this soft, the overburden where the shaft is located must be frozen before excavation can take place. The Cote Blanche mine is a producing facility which was built in 1958 by the Carey Salt Company. The original facility included a 14 ft diameter production shaft and a 7 ft-8 in diameter service/ventilation/escape shaft. This system was installed by The Cementation Company. In 1996 the owner decided to improve both the mine ventilation and production hoisting system by installing a third shaft. This shaft would be designed to extract 650 tons per hour from a depth of 1600 ft and provide 500,000 cfm of ventilation to the mine at a maxium design pressure of 4 in WG. These parameters resulted in a requirement for a 16 ft finished inside diameter concrete lined shaft and a headframe designed as a pressure bulkhead. Because the mine would operate from one level only, the most efficient hoisting system for the application was determined to be a ground mounted koepe running on rope guides. With these criteria fixed Cote Blanche embarked on a program which would see construction start in June 1998 with the first salt produced in February 2001 at a cost of $US18M. The major players in the design and construction were G.L. Tiley & Associates Ltd., BLM Bharti Engineering, Freezewall Inc., Phillips Mining, Geotechnical and Grouting Inc., Don Hart Consulting and Dynatec International.

May 1, 2002

By Matthew Violot

Vale Canada?s Birchtree Mine, located in Thompson Manitoba, has been experiencing problems with hanging wall / footwall dilution, as well as sloughing off of adjacent stopes and temporary stope block backs. Birchtree Mine is interested in determining how time affects the stability of their open stope blocks. Many factors simultaneously influence open stope stability (rock mass quality, joint condition, stress condition). This makes it challenging to determine the influence of a single parameter such as exposure time or stand-up time. This study focuses on determining the effect of exposure time on open stope dilution and combines stress analysis and empirical based approaches.

Jun 1, 2012

By I. S. Zajac, Y. O. Oyediran, M. C. Robart

This paper presents an overview of the metallurgical work on the Strange Lake Alkalic Complex (SLAC), from historical development of the "Main Zone" to present day develoment of the "B Zone". The SLAC, originally discovered by the Iron Ore Company of Canada (IOC) in the northeastern Canadian Shield of Québec and Labrador, is one of the world’s largest deposits of rare earth elements (REE) including yttrium and high field strength elements (HFSE) including zirconium, niobium, and titanium. It is part of a Precambrian, post-tectonic complex of peralkaline granites which intruded along the contact between gneisses and monzonites of the Churchill Province of the Canadian Shield. Mineralization of interest at Strange Lake principally occurs within peralkaline granite-hosted pegmatite and aplite sheets and, to a lesser degree, within the host granites, particularly in intra-pegmatitic granites. The highest grade and metallurgically most favorable mineralization is in the upper, open pit mineable parts of the SLAC. Metallurgical development has been conducted under a number of mining companies, and various value metals have been targeted throughout the history of the deposit, including yttrium, zirconium, niobium, and rare earths. Historic processing routes tested have included ore beneficiation, atmospheric leaching, solvent extraction (SX), and metal precipitation. This paper also presents the metallurgical development supporting Quest Rare Minerals Ltd.’s (Quest) 2013 Pre-Feasibility Study (PFS) and 2014 Preliminary Economic Assessment (PEA).

Jan 1, 2014

By T. Krumins, L. Zunti, R. Frischmuth

Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals, in high-temperature operations. In a vent application, titanium ignition risk is reduced by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature conditions and therefore titanium ignition risk is dependent on standard operating procedures, and process control interlocks and permissive conditions. It is not uncommon for standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions.

Jan 1, 2014

By Huan-Qiang Zhang, Gang-Hai Huang, Yu-Yong Jiao, Fei Zheng, Zhang. Xiu-Li

An efficient and accurate three-dimensional (3-D) contact detection algorithm is of vital importance in large-scale computing of discontinuous deformation analysis. The contact detection algorithm takes up a large proportion of the whole calculation time because of the increasing calculation number in three-dimensional case. For block systems which consist of convex polyhedrons, the efficiency and accuracy of the contact detection algorithm is a great challenge. The presented contact detection algorithm in discontinuous deformation analysis (DDA) method is carried out in three phases: the global neighbour searching, the local contact type searching and the contact transferring. A contact detection algorithm for 3-D DDA is presented with some improvements on the three phases. A grid-based global neighbour searching algorithm is used to eliminate unnecessary neighbour blocks to the exact number. The local contact type searching includes two steps. In the first step, the common plane method is used to determine the contact type between convex polyhedrons. In the second step, the contact pairs detected by the common plane method are divided into four basic types. In the third phase, the four contact types are transferred into two basic contact types, vertex-to-face contact type and edge-to-edge contact type, which are managed in a uniform procedure. Three verification examples are calculated, the results show that the proposed algorithm based on the three contact detection phases is robust and efficient.

Jan 1, 2015

By Robert K. Jonas

Mining companies can improve production and reduce costs by using the best available technology to control their operations. Many mines are challenged to use multivariable predictive control due to limited experience or staffing, as well as being concerned over the robustness and sustainability of predictive controls. As a result many mines are not realizing optimal performance from their assets, and thusly are not realizing the production increases or cost reductions that this technology can deliver. Over the past few years, the application of multivariable model-based predictive control has gained acceptance in many mining processes and has proven to be robust and sustainable for some of the most challenging mining processes. New automated modeling and performance monitoring software have greatly simplified the effort to implement and maintain these solutions. In addition, many progressive companies have chosen to co-source the implementation and service of these solutions to assure project success and continued benefits stream. This technology has been successfully applied to a wide variety of processes; grinding mills, alumina digestion, CCD washer and thickeners, kilns, calciners, roasters, flash smelters, heat exchangers, evaporators, and most recently in the demanding process of flotation. This paper discusses the state-of-the art in advance control technologies in the mining industry, including the impact of these technologies on maximizing benefits, and implementing best practices for long term sustainability. Benefits from recent multivariable predictive control applications in copper mining will be reviewed, and the use of the latest predictive control technologies and practices in mining will be discussed.

Oct 1, 2009

By B. Jakovljevic, M. D. Soderstrom, T. McCallum, A. J. Quilodrán

Cytec has developed a new organophosphorus based solvent extraction (SX) reagent for rare earth separations. The new product, CYANEX® 572, has been formulated to allow efficient extraction while minimizing the strip acid requirements. The optimization of formulation strength is expected to significantly reduce the operating costs of these circuits. Modeling capabilities for CYANEX® 572 (similar to those used successfully in Cu and Co/Ni SX) have also been developed to aid in the design and optimization of the SX circuits. Simulations will be shown comparing CYANEX® 572 to a traditional rare earth extractant.

Jan 1, 2014

By C. Cortés

Flotation is a highly interactive process where a change or disturbance in any part of the circuit results in different final grades and recoveries. This high variability of the circuit metallurgical performance complicates the diagnosis of the scavenger stage at the end of the line, as copper losses in the final tailings are erratic and not totally a consequence of problems in the scavenger section. The assessment of the scavenger performance requires a more elaborated procedure than that used for others stages of the circuit. This communication describes the application of an approach that combines results of laboratory flotation tests with those of surveys performed at the plant. The approach is based on running surveys in one of the circuit lines to collect samples for determining grade vs. recovery curves for total mass and size-by-size fractions. Full mineralogical and liberation analyses are also considered on some samples of the feed and tailings streams selected to have a range of feed grades. A separate sample of the feed is used to run laboratory flotation tests to determine optimum flotation time. Two additional pieces of information are the effect of operating variables on recovery, determined through a test program based on design of experiment techniques, and operational data on every cell in the line gathered by visual observation. The application of this approach to one of the scavenger lines at Los Colorados concentrator (Minera Escondida, BHP Billiton) is demonstrated.

Jan 1, 2007