Search Documents

By Fritz F. Prugger

In August, 1970, during routine shaft grouting, a major water source was intersected. Water and quicksand under very high pressure entered the shaft at a rate of 65 m3 per minute. The mine and both shafts were flooded. The breach was sealed simultaneously from within the shaft and through a relief hole drilled from surface. The mine was dewatered, rehabilitated and the equipment was restored. Production resumed two years after the accident.

Jan 1, 1979

By T. H. Patching, M. W. Mikhail

"The gas sorption and emission characteristic of coals are important to the planning and conduct of mining operations. Methane drainage from coal strata can also provide a supply of fuel in certain circumstances. Gas emissions have also created hazards during the handling and transport of coals and the release of gas also appears to be related to the yield of fine sizes during mining and processing operations.This paper summarizes studies at the University of Alberta on the permeability and gas emission of certain bituminous coals. Permeability of 'solid' samples was found to be drastically reduced by confining pressure. An emission index, .P, which has been related to outbursting behaviour of coals, has also been related to the proportion of fine s in cleaning plants. Gas sorption isotherms are dependent on temperature, moisture content, the gas involved and the type of coal and can be approximately expressed by the Langmuir or the Freundlich equations. Sorption values in sections taken across a given seam were similar but considerable differences were found in . P indices in the different coal layers of a seam.IntroductionThe emission of gases, especially of methane, from coal has been a subject of great interest (and sometimes a matter of life and death), to those who dig and handle coal since it was first mined from underground pit s. Many studies and investigations have been carried out on gas occurrences and emissions but our knowledge of the precise mechanisms of gas sorption, desorption and flow from coal is still incomplete. It is the purpose of this paper to review the principal factors involved in these processes and to briefly rep ort some of the results that have been obtained by studies in the laboratories of the Department of Mineral Engineering, University of Alberta, and Coal Research Laboratory, Edmonton, CANMET"

Jan 1, 1986

By K. Fumimura, T. Nishimura, M. Kohno

When applying numerical techniques to problems of deformation of rocks, the body to be analyzed is divided into small portions and is represented by a system of points linked together with the neighboring points. In the so-called distinct element modeling, the particles in the system are directly connected by springs and a contact law is used to specify forces on the particles to simulate the mechanical behavior of the body. The relation between the spring stiffness and commonly measured material properties, such as the Young’s modulus and the Poisson’s ratio, should be known a priori. For the general case of a random packing of particles, the relation is found by means of a process in which a system of particles and set of parameters are prepared to simulate a set of specimen-size test and then the input parameters are chosen to match the measured material properties. The validity of the numerical result is only demonstrated by comparison model behaviors with the measured responses. The process includes trial-and-error manner, therefore, no model is complete to reproduce the mechanical properties. In this paper, a relation between the spring stiffness and the elastic constants; the Young’s modulus and the Poisson’s ratio, is introduced to a three-dimensional distinct lattice spring method. Two simple numerical examples will be presented to demonstrate the performance of the method with the procedure for the determination of the spring stiffness.

Jan 1, 2015

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada's current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today's commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By John A. Allan

The subject chosen for this paper is not a new one, but the subject matter is so extensive that something new can always be said .about it. We are just beginning to realize how little is actually known about the character of Alberta coal, except for a few general facts. The object of this paper is not to explain that our previous information, in whole or in part, on the coal resources of Alberta, has been incorrect, but rather to present some new facts obtained as a result of recent study in the field and in the laboratory. As field investigation continues the problem of determining the character of a coal seam for any great distance laterally becomes more and more complex. Our present knowledge of Alberta coal deposits should not be discussed before due reference is made to those great pioneers who blazed the trails for later geologists, by recording their observations on the general geology of Alberta. Geologists, to-day, particularly those of us who are striving, year after year, to unravel the mysteries of stratigraphy, palaeontology, and structure, in so far as these are related to the coal resources of Alberta, fully realize our indebtedness to those three trail-makers, Dawson, McConnell, and Tyrrell. Had these geologists not recorded their observations correctly, nor interpreted the broad geological facts contained in Nature's book, with still uncut pages, how much slower would have been the progress of our coal knowledge in the succeeding years. It is true that many of the interpretations given to observations by these pioneers have had to be changed as a result of closer studies, but we must also expect that the geological interpretation from present day observations will be changed by future workers, as Nature's book is read and re-read.

Jan 1, 1925

By M. P. Kat, R. J. Barclay

"In 1984, a provincial inquiry into ground control and emergency preparedness in Ontario mines was commissioned by the Minister of Labour for Ontario. One of the recommendations put forth by the committee conducting this inquiry was that the Ontario mining regulations be modified to address more effectively the assessment of mine design. Mining regulations now require that every mine in the province annually assess its design with respect to ground stability. Subsequently, the Ministry of Labour has embarked on a ground control audit program to gather as much information as possible about the ground control programs in place at Ontario mines. In 1988, 47 underground mines were audited. The audits are intended to provide an overview of the level of engineering effort that is devoted to ground control on a provincial basis, by identifying the type of geotechnical information that is collected by each mine and how this information is used for stability analysis purposes in rationalizing excavation and support system designs. Also, the audits serve as an indicator of the severity of ground stability problems at individual mines, and how these problems are dealt with.This paper consists of information that has been extracted from the first series of ground control audits that were conducted in 1988. Specifically, the paper describes the types of support systems that are used in Ontario mines. It also discusses the rationale for local ground support selection, and the quality control programs that are in place for assessing the performance of installed ground support. As well, the type of geotechnical information that is collected, and to what extent it is used for the purpose of designing ground support systems, is reviewed"

Jan 1, 1991

By W. Evans, C. E. Ells

Nuclear power reactors using zirconium alloy pressure tubes generate electricity in several countries. Such reactors are particularly important in Ontario, where CANDUs* generate about 30% of the total electricity produced in the Province. Starting with the commitment of NPD-2 in 1956, the pressure tubes of the first five CANDU reactors were made of coldworked Zircaloy-Z, an alloy of Zr and Sn. This alloy was developed by the US Navy, but the decision to use it in a cold-worked condition was based on AECL work. In 1958, the USSR published information on a new alloy, Zr-2.5 wt% Nb. The Nb promotes stabilization of the (3-phase in the material, thus presenting opportunities of exploiting metallurgically strong pressure tubes analogous to the heat-treatable cx-{3 titanium alloys. After construction of two reactors using Zr-2.5 wt% Nb in a quenched and aged condition, an extensive development program on cold-worked Zr-2.5 wt% Nb pressure tubes resulted in them becoming the reference tubes for all CANDU reactors committed since 1966. Anticipating the future needs of the domestic and export markets, AECL have pressure tubes of Zr-3.3 wt% Sn-0.8 wt% Nb-0.8 wt% Mo (Excel) in an advanced state of development. These tubes will be used in an annealed condition; our projections show that they will have improved dimensional stability over the lifetime of the reactors. These improvements result from experimental programs leading to an understanding of the relationship between microstructures and fabrication variables and effects of the environment during service in nuclear reactors.

Jan 1, 1981

By Richard Cyr, Peter Larsen, William Quesnel

"The need to continually improve efficiency and lower costs in mining operations is of paramount importance to all concerned in the industry. Mining operations are constantly testing new methods and equipment in order to lower costs and improve productivity. Equipment suppliers strive to fulfill the demands of the mines through improved design and innovative ideas for productivity increases. In some cases, however, an increase in productivity does not require new equipment design, but rather the application of an existing mining method into different operating parameters. Such is the case in applying longhole methods to narrow vein ore deposits.Bulk mining methods have long been recognized as efficient, low-cost alternatives in narrow vein operations. Typically, shrinkage and some cut-and-fill methods are employed. The shortfall of these methods is the tendency to be labour intensive. The demand for miners skilled in these methods far outweighs their availability. Consequently, labour-efficient methods have to be employed to fill the void. The application of longhole drilling techniques to narrow vein deposits is one such method.IntroductionPercussion longhole drilling evolved in Canada in the early 1940s. Prior to percussion drilling, blast holes were drilled using diamond drill equipment. Jack Gardner, of Gardner Steel, began testing with carbide percussion bits and extension drill steel in applications where diamond drills had been previously employed. Percussion drilling equipment proved to be considerably more productive and cost-efficient. The experiment eventually led to the replacement of diamond drills in this application.Over the years, the percussion methods were improved, with particular emphasis on the equipment used. Rifle bar rotation machines evolved to independent rotation. Bar and arm set ups evolved into self-contained mobile drill carriers that increased productivity while reducing the physical labour. The introduction of hydraulics further improved efficiency and production figures. Today, it is not uncommon to see fully computerized jumbos in production longhole drilling applications. These machines represent the ""state-of-the-art"" in longhole drilling equipment.Production longhole drilling is considered to be one of the most efficient bulk mining methods in use today. Production statistics normally exhibit low-cost, efficient ore extraction. As a rule, longhole (blasthole) methods are associated with substantial ore deposits. These methods have exhibited high production figures and low mining costs.Over the past decade, long hole methods have been applied to several narrow vein deposits. These applications have proven that, given the right parameters, longhole methods will produce the same advantages in narrow vein deposits as are seen in more conventional applications."

Jan 1, 1990

By G. W. Poling, J. R. Hoffert

"A common practice in preventing gravity-fed tailing pipeline from plugging due to sanding is to add lime at relatively high dosage rates. The lime affects the rheology of the slurry ""vehicle"" which transports the coarser particles in a heterogeneous flow-regime. This paper describes a study of the effect of lime on the critical deposition velocities and friction head losses of Highmont Mining Company's mill tailing. Testwork using an extrusion viscometer was related to the surface chemistry changes brought about by the high lime additions. Lime additions which typically increased the tailing pH from 8.4 to 11.5 reduced the critical deposition velocities from approximately 3.2 to 1.7 m/sec.IntroductionCommon practice, at least in base metal concentrators in British Columbia, is to use high lime additions in tailing slurries when the pipeline becomes partially plugged with sands. Some concentrators, such as the Highmont Mining Co. Ltd. plant, add lime on a continuous basis during low tonnage periods and during startup/shutdown transition s. Although such high lime additions often solve temporary plugging problems, the effect of lime on slurry rheology has not been well understood.Slurry pipelines are designed to transport solids in suspension with a minimum of wear and without particle deposition. These two objectives are in opposition because the velocities required to maintain solid suspension can sometimes cause high head losses in the pipeline, as well as wear problems. Thus, the optimum velocity for a long distance slurry pipeline is in the range that provides just enough turbulence to keep coarse particles in suspension."

Jan 1, 1985

By M. I. Kalashnikova, Y. M. Shneerson, E. E. Zhmarin, Y. V. Degtiarev, E. M. Vigdorchik

Separation of a magnetic fraction from nickel concentrate following matte flotation, and its treatment in a separate circuit enable reduces precious metals losses. The magnetic fraction is treated in two stages of oxidative leaching: atmospheric and pressure leaching. A study of the atmospheric stage, using mathematical modelling, is described in this paper. The mathematical model and experimental data were used to carry out industrial process calculations. The model enabled extrapolation of the results of batch laboratory test to industrial-scale continuous processing and the selection of optimal process conditions and large-scale equipment. In December 2004, commercial oxidative leaching tests were performed on the magnetic fraction at the Severonickel Plant (Monchegorsk, Russia). A comparative analysis of the mathematical modelling results and the actual process parameters is presented.

Jan 1, 2005

By Masatsugu Morimitsu

This paper introduces new technology of oxygen evolution anodes which can be applied to produce copper, zinc, cobalt, and other metals by electrowinning. The anode consists of nano iridium oxide particles dispersed in amorphous tantalum oxide matrix as a catalytic layer formed on a titanium substrate. The anode can reduce oxygen evolution potential by 0.25 to 0.55 V compared to commercially available lead alloy anodes and can suppress unwanted side reactions such as manganese oxyhydroxide, lead oxide, cobalt oxyhydroxide which occur during oxygen evolution in the electrowinning solutions. This technology is effective for environmentally friendly electrowinning processes with low energy consumption and less anodic deposition.

Jan 1, 2011

By F. Habashi

"Extractive metallurgy was divided into the three sectors pyro-, hydro-, and electrometallurgy in 1959 when Professor Joseph Newton at the Idaho School of Mines in Moscow mentioned this in his book Extractive Metallurgy. Pioneer hydrometallurgists who built this discipline can be traced to the alchemists in the ninth century. It is now a mature subject of great importance in which pressure plays a vital role. Short biographies of some hydrometallurgists and the processes they invented are briefly outlined.INTRODUCTIONHydrometallurgy is the use of aqueous solutions to recover metals from ores. It is a relatively new discipline when compared with pyrometallurgy the use of fire to melt ores and recover metals which was practiced in ancient times. Hydrometallurgy can be traced to the time of alchemists whose concern was the transmutation of base metals into gold. Although alchemists did not succeed in their venture yet they described many reagents that are useful today. For example, they prepared sulfuric acid by distillation of iron vitriol, muriatic acid by distillation of sulfuric acid with salt, and nitric acid by reaction of sulfuric acid by reaction of sulfuric acid with salpeter. Jabir Ibn Hayyan the Muslim alchemist who lived in the ninth century (Figure 1) described aqua regia a mixture of nitric and hydrochloric acid that can dissolve gold although either acid has no action on gold. THE MIDDLE AGESIn the Middle Ages, it was reported that copper was recovered at Rio Tinto in Spain by allowing copper-containing pyrite to be exposed in piles to the action of air and rain. Copper sulfate solution obtained was treated with pieces of iron to precipitate metallic copper—a process that was called cementation. Georgius Agricola (1494–1555) (Figure 2) a medical doctor in Saxony who used to visit mines and smelters to examine miners and metal workers, described in his book De Re Metallica the parting of gold, i.e., separating of silver from gold by acids."

Jan 1, 2016

"Abstract - An estimation of resources of structurally complex gold lodes and stockworks represents a challenging task for geoscientists due to the complex geometry of the lodes and discontinuous grade. In the present case study, the resource of a gold stockwork has been estimated by uniform conditioning after the lode has been subdivided into geostatistically defined domains using the indicator probability model. The indicator probability model represents a powerful tool for structural interpretation of the mineralization and can be applied when traditional 3D volume constraining methods (wireframing) have failed to produce a unique, non-subjective model. For comparison, the resources of the same zone have been estimated without domaining. Results of the study clearly show that estimates obtained without domaining of the mineralization can yield a substantial error due to excessive smoothing of the grade.Application of uniform conditioning for modelling the grade distribution has a significant advantage over linear methods (e.g., ordinary kriging). Uniform conditioning enables estimation of local recoverable resources at different selective mining unit sizes that can be substantially smaller than the drilling density without creation of biases or over smoothed local values."

Jan 1, 2002

By Y. Prevost, D. Verhelst

"A computer-assisted process control system for the Noranda Process Reactor Wa5 installed at the Home smelter in 1991. Operating as an advisory tool for the furnace operators, and using a flexible oxygen balance as the basic building block of the computer program, the new control system has helped to reduce the variability in the grade of the matte produced by 50% . The smelter is currently operating at a 72% copper matte, with a standard deviation of between 1.0 and 1.3, while treating a wide range of concentrates, secondary materials and scrap. Enhanced process control has allowed for longer reactor campaigns, and improved stability of the converting operation.This paper reviews the feed classification and blending practice used at the smelter, outlines the strategy of the new computer control system, and summarizes the benefits realized since the implementation of the system in early 1990.IntroductionUntil 1989 the Noranda Home smelter operated as a multi furnace smelter, at one time having three hot-charge reverberatory furnaces, and finally operating with one wet-charge reverberatory furnace and one Noranda Process Reactor. In 1989 the final reverberatory furnace was closed and the Reactor became the sole smelting vessel, treating around 750 000 tonnes of concentrate, secondary materials, and scrap per year. At the time of the start-up of theNoranda Reactor in 1973, the vessel was capable of treating 750tonnes per day of a heterogeneous mixture of copper concentrates, fluxes and secondary materials to produce copper in one operation. Through process improvements, and the introduction of additional oxygen in 1982(pannell and Mackey, 1988), the daily tonnage increased to 1800 tonnes by 1988. The operation had also been changed to produce a high-grade matte instead of copper. Figure1 illustrates the main features of the reactor, a cylindrical vessel which is charged at one end and tapped at the other. The matteis subsequently processed through Peirce-Smith converters and anode furnaces before being cast into copper anodes. Figure 2 outlines the progressive increase in the furnace smelting capacity. Over this period the percentage of secondary materials, and scrap feeds also increased to approximately 110 000 tonnes per year, or 15% of the total new feed input (Bedard et al., 1991). Now operating wholly as a custom feed operation, the Home smelter can treat over 2200tonnes per day of new metal-bearing material."

Jan 1, 1993

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)':• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker 's exposure to the numerous types of particulate matter that may be present in the workplace. The paper ' reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

By R. J. Mitchell

"Centrifuge modelling of earth structures is a well-proven technique for evaluating the performance of prototype structures using physical models. The applications of this technique have increased dramatically during the last decade such that even the modelling of dynamic responses in structures has been accomplished.This paper presents the first model test results used to design a mine backfill. The models were tested using a 3 m radius 30 g-tonne geotechnical centrifuge which was constructed at Queen's University specifically for model studies on mine backfill stability and subsidence. The models represent the first production blast-hole stope to be mined at Westmin Resources Ltd. 's H. ~ Mine on Vancouver Island. This paper includes photographs of:model failures in the centrifuge and correlations of model test results with analyses based on unconfined and triaxial test data.IntroductionDuring the feasibility study and development stages for the H.W. Mine, Westmin Resources Ltd. conducted a comprehensive rock mechanics and backfill engineering program. The results of these studies indicated the need for assurance of backfill stability during pillar recovery on the initial blast-hole mining block. The cemented tailings backfill had to be free standing for heights up to 25 m and the potential for surcharge loading from a weak hanging wall zone, the potential for fill block sliding down-dip and the potential for seismic loading had to be considered in the design of the fill strength. The basic questions to be answered were: what cement content is required and will the resulting backfill costs be economic relative to the proposed mining method and sequence? Figure I shows a typical cross-section through the first mining block . The up-dip stope is to be mined first and backfilled with cemented tailings . The down-dip stope would then be mined and filled. Depending on ground conditions encountered, the complete intervening pillar could be recovered and the void backfilled with uncemented tailings or it could be recovered in small sections by exposing limited back and wall areas, backfilling with waste rock and I or cemented tailings . This latter method is commonly referred to as the Avoca method"

Jan 1, 1987

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By J. Lebl, S. Bharti, D. J. Cornett

"This paper presents the design and application of blasthole mining to an area at Strathcona Mine previously employing post pillar cut-and-fill. Extensive mining in the area had led to gradually deteriorating ground conditions and post pillar stoping was no longer considered acceptable. Alternative methods had to be investigated.Conventional methods for mining in poor ground were rejected because of the high cost. Blasthole mining was selected because iI offered good productivity and safety with acceptable costs. The design of this approach involved field investigations and the use of numerical modelling to simulate the different blasthole options and their impact on ground stability. The blasthole design incorporated reinforcement with cablebolts, use of a radio-controlled remote LHD unit, large-diameter holes, blast design and wall control. Potentially unstable areas were outlined during mining with ground monitoring instruments and the results used to modify mining plans during the production phase.IntroductionIn underground metal mines there is a need to improve safety and productivity and lower mining costs in order to maintain reasonable rates of return on investment. This requires the application of good engineering design to both mine planning and ground control in order to optimize production and costs and to forecast potential problems during mining. The task becomes more important when extensive mining leads to gradually deteriorating ground conditions, making existing mining methods and techniques no longer acceptable from a safety point of view. Alternative mining methods must, however, be sufficiently productive to ensure profitability. This paper presents an example of the engineering design and operating approach used by Falconbridge in dealing with such a situation at Strathcona Mine."

Jan 1, 1983

By Ö Yilmaz

In this study, the behaviour of rock mass subjected to blasting load is investigated using three dimensional finite difference numerical modelling. In the analyses, Mohr-Coulomb failure criterion has been used for the characterisation of the rock mass strength. Stresses acting on the borehole boundary have been simulated by an exponential function which reaches its maximum within a short time and then falls to zero value in a considerable time period. The strain rate effect on the mechanical properties of rock material has also been taken into account in the analyses. Four different explosive-rock mass combinations have been studied to investigate blast induced damage zone. It has been observed that proposed equation for the dynamic compressive strength of rock material fits very well to general suggestions. Results have shown that blast damage analysis model recommended with this study is successful.

Aug 1, 2013