Search Documents

By S. J. Buckler

Many metallurgical processes use submerged gas injection to increase the contact area between gas and liquid phases in order to promote faster overall reaction rates. The work presented in this paper is part of an experimental investigation to measure the gas-liquid interfacial area available in bubble plumes within molten metal baths. Measurements of the nitrogen absorption rate during submerged injection into molten iron baths have been used to estimate the interfacial areas of the bubble plumes. A theoretical model was used to predict the superficial nitrogen transfer rate under mixed liquid phase mass transfer -interfacial reaction control. The interfacial area was calculated by dividing the overall nitrogen absorption rate by the superficial rate. Reasonable agreement was obtained between the interfacial areas measured in our laboratory with data from a comparable system reported in the literature. The experimental results were compared with the predictions of three theoretical models and one empirical correlation. The models of Turkdogan (3) and Zhao and Themelis (5) gave the best agreement with our data.

Jan 1, 2004

By Q. Han, W. Dai

Al-Ti-B type master alloys have been widely used in the grain refinement of aluminum since 1940s. The introduction of Al3Ti and TiB2(AlB2) particles reduces the grain sizes down to about 200 micrometer level and makes cold work possible. However, the mechanism for the grain refinement is still not clear, though it is believed that TiB2 in the presence of Al3Ti nucleate a-Al grains in solidification. This paper presents our finding on the formation of (Ti,Al)B2 solid solution, which leads to a proposed theory on grain refinement by Al-Ti-B type master alloys that upon addition into aluminum melt stable TiB2 particles react with aluminum slowly and release titanium into the melt. The titanium thus released in combination with titanium in the melt through dissolution of Al3Ti maintains a transient titanium-rich layer on the surface of (Ti,Al)B2. This layer offers a low crystal mismatch with a- Al and promotes the nucleation of aluminum grains.

Jan 1, 2014

By Göckmann. Klau

"IntroductionCopper has been recycled ever since its discovery. Even in Graeco-Roman times recycling of this resistant, and thus valuable material was carried out as a matter of course. Just take, as an early example, the Colossus of Rhodes: after the figure collapsed during an earthquake, the bronze parts were melted down into ingots and sold.Copper is a material which can be recycled again and again because copper produced from recycling is not different from copper originating from primary materials. This is mainly due to electrolytical copper refining whereby not only the base metals but also the precious metals can be removed. In contrast, with aluminum and iron only the more electropositive elements can be removed by refining, and the resultant scrap must, therefore, be sorted mechanically into various alloys for subsequent smelting.The recycling rate for different base metals is given in Table 1. Despite this ideal prerequisite, the generally quoted recycling rate of copper of about 40070 appears rather low. However, it must not be forgotten that the recycling rate is defined as the ratio of the annually utilized quantities of copper scrap and the annual production figures (Table 2). Moreover due to the economic growth over the last 30 years the availability of copper from scrap materials is lower than its consumption because copper is principally employed in very long-life consumer durables and only returns to the recycling circuit after many years. The average time for the copper of some goods to be recycled is detailed in Figure 1."

Jan 1, 1992

By L. J. Visentin, J. G. Rickaby

"Audiometric testing is a key element in hearing conservation in the mining environment. This paper gives the history of the audiometric testing program carried out by Inco Metals Company, including the program objectives the personnel and equipment involved, calibration and testing, the test procedure, and the classification and evaluation of the test results.IntroductionThe operations of the Ontario Division of Inco Metals Company are located primarily in the Sudbury District. They also include a refine ry at Port Colborne and a mine and concentrator at Shebandowan near Thunder Bay.The company operates nine underground mines, and one open pit, while maintaining six underground mines on a standby basis. Ore from these operations is processed in four concentrators. The metallurgical facilities include a smelter, a matte processing plant, a copper refinery, a nickel refinery and an iron ore recovery plant at Sudbury, and a nickel refinery at Port Colborne. Inco Metals currently mines roughly 9,000,000 tons annually and produces IS elements.Excessive noise in the work place has been a serious problem in the mining industry since the introduction of compressed-air-powered machinery in the last century. At the same time, growing levels of noise inherent in our social environment can threaten the hearing of employees and their families.Only in the last 20 years, however, has the extent of this problem and its implications for people working in the industry and their families been recognized. Since the industry has become aware of the situation it has taken steps to implement comprehensive noise reduction and hearing conservation programs."

Jan 1, 1982

By L. C. Bird, A. I. A. Salama, M. W. Mikhail

"A program of sampling in Canadian washeries was carried out by the Coal Research Laboratory (CRL) over a period of two years to evaluate the performance of various density separators in these operations(1). Operating data on quality and recovery of products, separation efficiencies and cutpoints for each separator type are compared with data predicted using computer models developed from previously existing data.The Heavy Medium Cyclone (HMC), Heavy Medium Bath (HMB) and jig models give predictions of recoveries and qualities of products for sizes coarser than 10mm with absolute value of error mean less than 7 per cent, whereas predictions of the Water Only Cyclone (WOC) model for -10mmfine coal are with absolute value of error mean less than 8 per cent. Although less accurate for -10 mm fine coal, the HMC and jig models produce predictions of recoveries with absolute value of error mean less than 2 per cent and quality of products predictions with absolute value of error mean less than 28per cent which are generally acceptable because more liberation in the fine fractions appears to compensate for any difference in the accuracy of separation, resulting in good prediction of the clean product. However, ash content of the actual fine refuse was lower than predicted. The difference is attributed to the highly friable nature of Canadian coals which tends to cause an excessive loss of coal fines to the fine refuse.A comparison study based on quality and recovery of products is made between the Dutch State Mines (DSM) models and the recently modified models, both produced comparable predictions."

Jan 1, 1985

By M. J. Steffens

ESPLIM is a novel separation technique that combines the advantages of solvent extraction and electrostatic dispersion but its application in the extraction of nickel by the direct solvent extraction route and the effect of high electrostatic field on the stability of organics have not been explored. These were investigated in this study and it was found that the technique allows 97% extraction of the nickel in a single stage compared with 3 stages by the conventional solvent extraction. Also, three months of exposure to 5.0 kV under simulated operational conditions had no adverse effect on the stability of organics.

Jan 1, 2005

By Deni Lessard, Roger Demers, Noël R. Billette

"The Quebec Mining Association has for many years been supportive of the activities of the Centre de recherches minérales which were initiated to ensure regular production hoist and cable inspections to maintain safety and productivity standards in underground mines in Quebec. CRM and CANMET have agreed to fund a Quebec Mineral Development Agreement contract to capture this accumulated knowledge. Using VP-EXPERT to process the information and subdirectories to store regulations, the prototype access D-BASE III records on hoist information and LOTUS 123for simulating working conditions that meet local regulations and expert rules of thumb criteria. Objectives are to improve safety in emergency operating procedures, maximize hoist productivity and safety, and promote knowledge transfer to operators."

Jan 1, 1992

By T. D. Traubert, J. T. Dietz, D. Catena

"Canadian process industry experts have often observed the strong trend for U.S. industrial safety and environmental laws to creep across the border. These experts will be interested in new United States (OSHA) regulations (29 CFR 1910.119), and anticipated new U.S. Environmental Protection Agency (EPA) regulations that will require over 28 000 U.S. refineries and chemical plants employing more than three million workers, to begin a comprehensive Process Hazard Analysis (PHA) of these complex plants immediately. Impending EPA regulations are expected to expand these efforts and add process Hazard Frequency and process Hazard Consequence reviews for many additional industrial locations.These regulations were created to reduce catastrophic industrial accidents, and emergency releases of hazardous chemicals which endanger employees, the public, and the environment.Accurate, and field verified Piping and Instrument Diagrams (P&IDs) are essential to permit a meaningful Process Hazard Analysis or emission release to be done. Today accurate P&IDs often do not exist. Many companies that have started to update their old P&IDs have found the process to be far more difficult, time-consuming,and expensive than they ever thought.This paper describes a new technique of computer drawn ""Intelligent"" P&IDs that can make a Process Hazard Analysis less expensive, more accurate, easier to perform, and provides lasting benefits to the plant owner long after the PHA has been completed."

Jan 1, 1993

By John F. Gartner

"New terrain maps provide information on the ground conditions in northern Ontario. This information has a relevance to mineral exploration because it assists the user in determining ground conditions prior to entering the area. The prospector, geologist, geophysicist and geochemist can then plan for the optimum use of exploration techniques best suited for theseground conditions.These terrain maps are the result of the Northern Ontario Engineering Geology Terrain Study-a program carried out by five consultants under contract to the Ontario Geological Survey of the Ministry of Natural Resources. The area mapped is 370,000 km2 and more than 100 basic data maps at a1:100,000 scale will be published.An unique terrain legend was derived to facilitate the mapping and it allows the derivation of specific user information. Examples of some of these uses are described. Introduction""Where did all the boulders come from Charlie?"", asked the student, as the prospector and his young assistant clambered through the bush. "" Why son, they were brought down here by the glacier"", the prospector replied. ""But where is the glacier now Charlie? "", persisted the young man. ""Gone back up north for more boulders son!""An old story, but one that illustrates the importance of overburden to the prospector. The use of overburden as a prospecting technique is not new. In fact, the principles have been known in the western world for at least 235 years (Shilts 1976). More recently, Dreimanis's classic work on boulder tracing (1957) and Lee's work (1971) emphasize the role of glacial geology in prospecting. In addition, papers by Smee and Sinha (1979), Averill (1978), Bereton (1978), and Gleeson and Hornbrook (1974) all describe the importance of drift in mineral exploration programs. The discovery of the copper deposit in the northern Ontario township of Currie (Thompson, 1979) is attributed in part to till prospecting methods. So the significance of the overburden is firmly established, both in the literature and in the minds of today's prospectors, geologists, geophysicists and geochemists."

Jan 1, 1981

By P. R. A. Andrews

"A sample of flotation feed from Bakertalc Inc., High water, Quebec was subjected to flotation evaluation to improve the recovery of talc. A number of alternative frother/collectors and depressants as well as flotation parameters including pH, conditioning time, frother/collector concentration and pulp density were assessed. In addition, the possibility of using a size coarser than that currently employed for flotation (95% minus 50 um) was investigated.As far as possible, a laboratory duplication of the present circuit arrangement was folio wed so as to minimize the cost of any changes. The best results obtained were a concentrate analyzing 95.96% acid insol for a recovery of 65.98% after four stages of cleaning. With recirculation of cleaner tailings, the recovery would be higher.The possibility of using an alternative method, based on the natural ability of talc to float unaided by a frother/collector, was briefly explored with encouraging results.IntroductionBakertalc lnc ., located in the eastern townships at Highwater, Quebec, Is approximately 140 km east of Montreal near the Vermont, U.S. border. Originally called Baker Mining and Milling Co. Ltd., it has produced pulverized talc products since 1938(1 ), although records show that talc was mined in the area as early as 1871(2). Feed to the mill originally was obtained from local deposits, but since 1952 the van Reet mine near south Bolton, approximately 25 km from Highwater, has been the source of ore .In 1957 a Raymond high -side roller mill was installed which enabled production of a greater range of talc products and, in 1960, new crushing equipment and a dryer were added. Other additions to the mill were the introduction of wet magnetic separation, although this was later discontinued, and flotation to produce high-grade talc concentrates."

Jan 1, 1985

By Gerhard Melcher, Hermann Hilbrans, Michael Gamroth

"IntroductionSeveral new smelting processes have been proposed and developed during the last 20 years. This has been true, in particular, for copper smelting technology. The important impulses for the advances in this field have been the recent demands regarding the environmental protection, energy saving and improved utilization of the metals contents of deposits, in particular that of complex raw materials.The methods developed more recently for pursuing these objectives have been outlined in several papers. In some of them the advantages and drawbacks of certain developments have been stressed. These documents are of great importance for assessing the different processes. The following paper tries to explain some details of the cyclone smelting process taking into consideration a few of these well-known presentations. The effectiveness of operation of the cyclone smelting process indicates that this process presents a significant achievement when compared with other conventional methods.The application of the CONTOP smelting cyclone range s beyond the field of copper metallurgy or the smelting of sulphide concentrates with the aid of oxygen. The research work carried out in the pilot plant of KHD Humboldt Wedag AG in Cologne-Porz also includes the recovery of the metal contents of intermediate products and processing of smelter residues which have to be converted in a disposable stat e, free of environmental pollution. This paper explains a few examples in this regard."

Jan 1, 1987

By Andrew J. Neale, Brian C. Flintoff

"In most mineral processing operations the term ""audit"" is usually reserved for the exercise of checking financial records and/or safety practices. While these activities are time-consuming, no one disputes their necessity or value. If these areas are subjected to such careful scrutiny, why is it that the same principles are not normally applied to critically examine process operation. After all, the operating efficiency of the plant impacts directly on the measures of profitability.A mineral processing plant is a complex system that has a number of distinct, but mutually dependent elements: process equipment, instrumentation, operating policies, maintenance policies, control strategies and people. To ensure maximum economic performance in the dynamic environment that characterizes a concentrator, requires a periodic review of each of these areas. However, to be useful, the study must be based on sound metallurgical principles and be conducted in a highly focussed manner. Experience has shown that the exercise is very revealing and rewarding.This paper will discuss the plant audit process and illustrate its potential value through examples taken from plant studies."

Jan 1, 1992

By W. Mirihange

Considerable mechanical property decline is always observed at the Heat Affected Zone (HAZ) of AA 5083, This occurred as a result of the thermal effect on the hardened material, It is highly beneficial to have a prospective metallurgical procedure to overcome this decline of properties. Therefore, experiments were set to evaluate the effectiveness of a quick post weld heat treatment process with the AA 5083, Optimum results were obtained at 473K and with approximately 600 seconds time, The interplay between the time, temperature and mechanical properties are possible to explain by the Lifshitz-Slyozov-Wagner (LSW) theory and by considering the composition of the material.

Jan 1, 2005

By P. L. Lehoux, R. F. Lopes

"Unanticipated low recovery or extraction of gold from heap leachable are can often be attributed 10 phenomena such as non-uniform percolation (channelling) of solution through heaps, excessively slow percolation rates due to densification of ore during stacking on the pads and parasitic or competing reactions of the cyanide solution with undesirable elements or geochemical ""impurities"" in the ore. The nature and causes of these phenomena are discussed in this paper, and it is suggested that geotechnical and geochemical expertise can contribute significantly to a better understanding of the relationship between laboratory results and actual field performance of the leaching process. Recommendations are made for bench-scale metallurgical testing to be complemented by geochemical and geotechnical laboratory evaluations, to ensure more successful heap leach projects. IntroductionHeap leaching is a simple, low-cost method of recovering metals from low grade ores which has now come into widespread application particularly for gold and silver metals in the United States.The heap leach process involves percolating a lixiviant (leaching agent) solution through broken or crushed ore (Chamberlain and Pojar, 1984). In the case of gold a dilute sodium cyanide solution is used and crushed ore is ""heaped"" on specially prepared impervious pads.The potential for use of heaping leaching methods for northwestern Ontario gold deposits was discussed by Beard (1983), who suggested that the use of this extraction technique in Canada should grow significantly for low grade ores as well as for small high grade deposits which cannot justify the installation of a new mill or the use of remote custom milling facilities. Two other potential situations for lise of a heap leaching extraction method are : as a low capital cost cash generator in the opening phase of a larger new project, and as a low cost output augmenter to complement a milling operation."

Jan 1, 1989

By F. Kitzinger

Electromagnetic testing of wire rope has become more and more reliable over the past two decades. This improvement is partly a result of an unprecedented progress of electronic technology, which permitted the development of a new breed of testing instruments. There are two basic methods for the electromagnetic testing of wire ropes, the AC method and the DC method. Both methods rely on magnetic field disturbance caused by mechanical anomalies in the rope structure. The wire rope under test is passed through a magnetic excitation field, which can be a weak alternating field or a strong static field. Because the alternating field is produced by an alternating current, these instruments are of the AC type(l). In the early days of ND-testing, strong permanent magnets were not yet available; therefore, the static magnetic field was produced electromagnetically with direct current. Instruments based on static excitation are still called DC instruments(2), even though the field is now produced by a permanent magnet. Both these methods have certain characteristic features. The AC method can detect loss of metallic area caused by corrosion or other effects, whereas localized faults such as broken wires are better detected by the DC instruments . The basic principles of the wire rope testers have remained unchanged over the years and the improvements present in the new instruments usually reside in the signal processing and recording sections. The Instrumentation Department of the Noranda Research Centre* has been involved in a four-year development program which resulted in a new type of wire rope tester, the Magnographv** . This new instrument in many ways represents a considerable departure from the traditional wire rope testers. The Magnograph has already been patented in Canada and the U.S.A.(3), and patent applications are pending in other countries.

Jan 1, 1979

By S. C. Tadolini

"Roof bolts are the primary means of roof support in underground mines in the United States. Presently, post installation loads are measured on about 10% of the expansion anchor and combination bolts by using standard torque wrenches that Unit the accuracy of the measurements to about ±30%. No system has been available for measuring the loads generated on full-column resin grouted bolts. Mine roof bolts are long, slender, non-uniformly sized, roughly forged, and placed in a corrosive environment, creating obstacles for researchers trying to utilize ultrasonic reflection techniques to measure strain. A complete measurement system has now been developed by the U.S. Bureau of Mines, Denver Research Center. This system is being used successfully in determining loads measured on expansion anchor and combination bolting systems, examining the transfer mechanics of full-column, resin-grouted bolts, and measuring loads generated on bolts in an underground roadway support system.IntroductionMillions of roof bolts are used each year to provide structural support in underground U.S. metal, non-metal, and coal mines. Approximately 45% of the bolts used are expansion anchor, 45% are resin-assisted combination or full-column resin-grouted, and 10% are friction anchored. The effectiveness of these bolting types is dependent on a number of factors including rock density, bolt length, in situ stresses, rock properties, bolt pattern, installation tension, etc. When implementing expansion anchor and resin assisted combination bolts , installation and post-installation tension, or load, is a major determinant of support quality and subsequent behaviour of the reinforced roof. The method by which these systems carry roof loads is well understood and documented(1,2).The importance of these installation and long-term bolt tension measurements is well recognized and are required in the federal government regulations(3). A statistical sample of the bolts, lout of 4 during installation and lout of 10 inby the last open crosscut, is required to be measured using current torque wrench technology. The disadvantages of this system are the disturbance and weakening of the anchorage and limitations of accuracy to approximately ± 30%. The method by which resin-grouted bolting systems carry roof loads is much less understood, mainly because testing procedures used to evaluate point-anchor systems are not effective on resin-grouted bolts.Due to these problems, the U.S. Bureau of Mines designed a measurement technique that provided a highly accurate, low cost-per- bolt system that led to the development of ultrasonic pulse echo instrumentation. The original system was designed to measure the tension only on expansion anchor bolts. Recent developments and system modifications have permitted measurements on resin-assisted and full-column resin-grouted bolts. The use of these types of support systems has been increasing steadily in underground coal mines.The development of this instrumentation has provided laboratory and field results that help to explain the mechanics and relationships between the applied loads and the interaction between the grouted bolt system consisting of the bolt tendon, grout, and rock."

Jan 1, 1990

By D. Lessard, S. Nantel

"Surface crown pillars are important Canadian,mining structures. Mines operating in the Canadian Shield usually have several, forming a first line of protection from surface elements.Detailed technical information from twenty-four Canadian hard rock mines show that the deposits dip steeply and are generally either single or multiple veins. Considerable overburden usually cap the deposits. The rock mass is often altered and intersected by important discontinuities.The designs for these types of pillars lack basic data and are based on experience rather than a scientific approach. Regardless of the competence of the rock mass, the surface crown-pillar thickness to width ratios (an unscientific design tool used by the industry) are usually less than five. Rock bolting is, in almost every case, used as a support measure. However, there are many openings neither backfilled nor monitored.The characteristics of openings with surface crown pillars are also examined."

Jan 1, 1988

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers' special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers' position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

By D. Mraz

"In certain instances, rocks around underground excavations behave as a plastic mass. This paper offers several solutions to predicting the mode of plastic flow around cavities and designing mining pillars where plastic conditions exist.IntroductionWhen stresses around underground cavities exceed yield limits of the host rock, the material often behaves as a plastic mass. The best example of this phenomenon is the behaviour of salt rocks in deep salt and potash deposits (more than 500 m deep).However, many other soft rocks exhibit similar properties. For example, Jeremic(1) described certain types of coal yielding plastically under high pressure. Alder suggested that granulated rock behaves plastically.The object of this paper is to propose a de sign procedure for mining pillars exhibiting plastic flow due to the combination of rock properties and in-situ stresses.Prandtl(3) mathematically defined a concept of a generalized, perfectly plastic substance, not possessing the property of strain hardening (Fig. I). He had in mind, a solid with a quasi quasi-isotropic , polycrystalline structure having a well defined yield point, and he postulated that its material elements start and continue to deform plastically when the maximum shearing stress ""'MAX"" reaches a sharp limit, dependent on the mean value of the sum of the major and minor principal stresses:"

Jan 1, 1984

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988