Search Documents

By J. E. Gill

"The Wasa Lake property is a block of about 1,640 acres in Beauchastel township, Quebec. Gold was discovered there first in 1936 in what is now known as the 'Southern area ( Fig. 1). Stripping and trenching were followed by 9,218 feet of diamond drilling in twenty holes. A number of good intersections were obtained, but their interpretation in terms of ore was difficult. A shaft was then sunk to 220 feet vertical depth. Thirteen hundred feet of lateral work and 543 feet of diamond drilling were completed at the 200-foot level before work was discontinued in 1938. Results up to this point had been just fair.Early in 1944, surface diamond drilling was resumed. The first hole cut material of ore grade in a strong shear zone 1,000 feet north of the old workings, and holes to the east and west showed this to be an extensive gold-bearing zone.In August 1945, a main working shaft was started. This has been sunk to 550 feet slope depth. A cross-cut at 390 feet vertical depth was driven to the ore zone and, by drifting and drilling at regular intervals, a length of 725 feet had been tested to December 31st, 1946 ( Figs. 1 and 2). The results check those from surface drilling quite closely.In the main zone, scoping widths from 8 to 40 feet and averaging about 25 feet are indicated. The grade after dilution should be about 0.15 oz. gold a ton and operation will probably start at 1,000 tons a day."

Jan 1, 1954

By E. L. Warburton

Before entering into a discussion of wet washing, it will be advisable to consider the various phases and conditions sur- rounding the problem of cleaning coal from the Corbin mines. Corbin is located in the south-east part of British Columbia in the Crowsnest Pass district, about 35 miles north of the International boundary and about three miles west of the Flat-head Range of the Rocky Mountains. It is reached by a rail-way, about thirteen miles long, from McGillivray, B.C., a point on the Crowsnest branch of the Canadian Pacific rail-way, owned and operated by the Eastern British Columbia Railway Company, a subsidiary company of Corbin Coals, Limited. The coal is assumed to occur here, as principally elsewhere in the Rockies, in the Kootenai series of the Lower Cretaceous, but owing to the disturbed condition of the surrounding country and, therefore, the magnitude of the geological study involved, this has never been definitely worked out. The coal is of the usual Crowsnest high-grade steam-coal, containing from 9 to 12 per cent. of ash, but appears to have 4 to 5 per cent. less volatile combustible matter than other coals being mined in this district, a representative analysis being about as follows:

Jan 1, 1924

By M. J. MONEA

Canada's only economic high-swelling bentonite deposit is mined in Wilcox, Saskatchewan, by A vonlea Mineral Industries Limited. The bentonite resulted from devitrified and altered volcanic ash released during the Laramide Orogeny. Volcanic ash was deposited in a pre-Cretaceous basin that was formed by salt solution collapse structures. Sedimentary rocks in the Wilcox area belong to the Snakebite Member of the Upper Cretaceous Bearpaw Formation. Bentonite beds are 61 cm, 46 cm and 30 cm thick; these are separated by 365 cm and 182 cm of shale respectively. Saskatchewan bentonite is used primarily in the oil well industry.

Jan 1, 1984

By H. Q. Fan

Construction equipment is an important type of resources of heavy construction contractors. Since equipment breakdowns can cause project delays and significant financial losses, the contractors are eager to know those factors causing equipment failures directly or indirectly, related to equipment design, maintenance, and operations. Although Bayesian network can be used for diagnostic analysis of failure events or making predictive analysis, building a Bayesian network for such purpose can be difficult as the cause-effect relations can be subjective and their conditional probabilities change with a wide variety of causal factors. A hybrid approach is proposed in this paper to update the Bayesian diagnostic network structures and parameters using real life data, the conditional probabilities and cause-effect relationships can be dynamically updated with observed failure records to reflect the real life situations of a complex equipment system. A case study is conducted to show the benefits of the hybrid approach in construction equipment diagnostic analysis.

Aug 1, 2013

By J. M. Beeckmans, S. G. Butcher, M. Goransson

"The counter-current fluidized cascade is a novel and potentially efficient pneumatic gravity separation device. Data are presented on over 150 runs of cleaning Alberta thermal coals, covering several size ranges. The coarser sizes of coal were processed in admixture with a fluidizing medium consisting of 0.5-by 0.1-mm hematite (or magnetite) and limestone particles. The partition curves for coal particles larger than about 3 mm, mixed with fluidizing medium, showed that the sharpness of separation achievable with the cascade approaches that of wet heavy medium processes, whereas with particles in the size range of 3 by 0.6 mm the sharpness of separation was comparable to that of a Baum jig. Useful cleaning was also achieved with particles smaller than 0.6 mm , Throughput rates of up to 11 tonnes per metre width of cascade per hour were achieved, with no indication of a deterioration in performance.IntroductionPneumatic coal beneficiation has steadily lost ground vis-a-vis hydraulic beneficiation during the past quarter century, primarily because of the sharper separations achievable with the latter methods. Nevertheless, there are certain inherent advantages of pneumatic separation methods which would give them an advantage in the market place were it possible to increase their efficiency to be technically competitive with those of hydraulic processes. These advantages are a dry product, resulting in a higher calorific value per ton, and avoidance of the problems associated with treatment and storage of process waste waters. Also, although it may be necessary to dry the raw coal prior to pneumatic processing, the dry rejects produced constitute an ideal fuel for a fluidized-bed combustor, which could provide heat both for drying the coal and for other purposes."

Jan 1, 1982

By D. Lauzon, H. de Ruiter

"In 1988a decision was taken to design and install a computerized mine monitoring and control system. This system had to monitor and control all pumping and ventilation underground. The operation of the mine air heating, using waste heat from the mine water and compressors, was to be part of the system. It ultimately also had to interface with the four existing Canadian General Electric Series 3 PLC's which controlled the No .3 shaft loading pockets. Beside operational control and trouble shooting, the system is a valuable tool in energy management and ultimate savings are estimated at $50,000 per year.The final equipment selection was a General Electric Series Six PLC on surface with a total of 17 Series One Plus and Juniors PLC located underground. Data is transferred through a two-pair shielded cable using modems. Both analog and digital functions are being utilized.The basic monitoring and control system was commissioned during 1989and, due to a higher level of technology today, further improvements have been planned for the future. The system was designed by Walter Dow together with Gordon Champion of D.G. Champion Engineering Ltd. of Toronto. Advice for the ventilation part of the project was obtained from Maurice White, Independent Ventilation Consultant.The Ministry of Energy, Mines and Resources and the Ministry of Energy of Ontario approved this project together with the waste heat recovery project to qualify for a grant of$135,000 under the Enerdemo-Canada program.IntroductionThe Macassa mine is a narrow vein gold mine situated about 2 km west of the town of Kirkland Lake in northeast Ontario. The mine has been in continuous operation since 1933 and a total of about 3.0 million ounces have been recovered out of 6.6 million tons of ore ."

Jan 1, 1991

By Robert P. Dufresne

Electrolytic cells are used in electrowinning (EW) and electrorefining (ER) of non-ferrous metals such as zinc and copper, and are a critical part of the purification process. The cell is a large basin and has an electrolyte or aqueous solution, an anode and a cathode, an insulator, and incoming high amperage. Cells are exposed to unfavourable internal and external factors that have a direct impact on their lifespan. Their deterioration can be caused by incorrect polarity, insufficient magnitude, their construction, tension stress, thermal shock, corrosion and other, and their maintenance and replacement can be time-consuming, costly, difficult and environmentally unsafe. Occupational health hazards and dangers posed by the maintenance and removal of the cell should also be taken into consideration. Modifying the design and fabrication method of the cell, using chemical-resistant reinforcement, and increasing tensile and mechanical strength will defer maintenance for a very long time. This can be achieved by a double hull system that comprises full-length composite reinforcement, polymer concrete reinforced with fiberglass pultruded rods and rebars, fiberglass structural layers, and special resin matrices. This will provide protection against thermal shocks, corrosion, leakage, cracks. The design of this cell incorporates a lifting system that will afford quick and easy install without having to move a great number of cells in close proximity, since it is strong enough to stand on its own and not have to be bonded to adjacent cells. As well, the cell can be anchored with ease as it remains stable. This is especially important because space is limited to lift and manoeuver between the cell and the double-girder overhead travelling cranes. The lifting system can also prevent electrocution and loss in product quality, while increasing efficiency and safety in the workplace. Considerable savings in terms of production downtime are also part of the equation. INTRODUCTION Maintenance and replacement of electrolytic cells in electrowinning and electrorefining are operations that pose many challenges, health and safety concerns, and give rise to substantial operational costs. These problems have existed since time immemorial. Electrolytic cells are made of conventional concrete or polymer concrete, and because of the very nature of their composition and their exposure to severe and environmental conditions, their lifespan is short. Although polymer concrete is composed of high-quality materials, and has good thermal stability and resistance to chemicals, nonetheless, maintenance is frequently required in order to maintain the integrity of the cell and to ensure the quality of refined metals. Repairing concrete is a non-permanent solution as cracks will reappear, and every repair weakens the integrity of the cell a bit more, until it reaches a knock- down point and the structure is compromised. The cell needs to be replaced, otherwise the cell will collapse.

Jan 1, 2019

By Ming’an Wei, Qifu Duan, Jianmin Wu, Lusheng Zhou, HMR Group Limited / HMR Technology Canada Ltd., Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company Skega first introduced rubber magnetic liners, and then followed by the Chinese invention of metal magnetic liners. Traditionally, both liners were used in secondary ball mills and regrind ball mills for industrial applications, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged steel balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design. Due to the development of larger diameter ball mills and thus larger ball charge diameter (up to 80mm) especially in non-ferrous metal mining operations, the application of magnetic liners have been very limited. Based on “Magnetism theory” and the development of new materials, the HMR Group Limited has been conducting researches on examining the structures of magnetic liners, associated materials and magnetic circuits which led to the invention of the Nano Alloy Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5 m diameter × 6.5 m ball mill at the Erdenet Copper Mine in Mongolia. The NSML successfully handled a ball size up of to 80 mm, while achieving a service life of nearly 24 months, which is almost 3 times wear life of the original manganese steel liners.INTRODUCTIONDuring the development and utilization of mineral resources, mineral processing is an indispensably operation. The effective separation of various useful minerals depends on sufficient monomer dissociation of minerals in the ores. The crushing and grinding operation is prior operation of mineral processing. Ball mills are used in different concentrators. As the main consumption parts of mill, liners have been studied constantly. As a new kind of liners, magnetic liners besides can meet the requirement of production, and also have characteristics with maintenance-free, saving energy and increasing efficiency. So the magnetic liners are worth to be spread and applied world widely."

Jan 1, 2016

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By R. R. Irrinki

Abstract -The Key Anacon deposit consists of four sulfide zones called, from south to north : Key Anacon No. 1, Key Anacon No. 2, Key Anacon No. 3, and Key Anacon Copper Zone. Massive sulfides of zones 1, 2, and 3 are underlain by rocks correlated with the Nepisiguit Falls Formation and are overlain by matie volcanic rocks correlative with the Boucher Brook Formation. In contrast to zones 1, 2, and 3, narrow northwesterly-trend.ing, copper-rich fracture zones occur within the Patrick Brook Formation. Sulfides in zone 2 occur as three mineralogical associations, namely: pyrite-chalcopyrite, pyrite-sphalerite-galerta, and pyrrhotite-sphalerite-galerta. The distribution of lithologies and en-echelon patterns of the three sulfide lenses of Key Anacon No. 2 zone are the result of F1 and F2 folding. Zone 2 is the most promising economically, with proven reserves of 1.11 million tonnes grading 0.2207o Cu, 3.47% Pb, 8.41% Zn, and 96 g/t Ag; the zone is open below a depth of 427 m.

Jan 1, 1992

By Shigeomi Nishigaki

This paper presents quantitative indexes to evaluate operator?s bearing, difficulty in a task, and machine operability when an operator remotely controls a backhoe, and reports the use cases. The quantitative indexes would give her/him the opportunity to reflect on her/his works, and enable us to gain in-depth insight into the teleoperation, and furthermore give us with promising hints to improve it.

Aug 1, 2013

By G. M. Hughes

"400 cubic foot Agitair Flotation Cells are in use at Sherritt Gordon's Fox and Ruttan Mine Cu-Zn concentrators. The 4 impeller model No. 120, used at the Fox Mine Operation, appears to offer superior agitation and aeration qualities compared to the single impeller model 120A, in use at Ruttan. The advantages of the model 120 are most significant with ores of high specific gravity and coarse grind.IntroductionSherritt is using 400 cubic foot Agitair flotation machines at both the Fox and Ruttan Mine Concentrators.At the 3000 tpd, Cu-Zn Fox concentrator, 18 model 120 machines have been in operation since May, 1969.The 10000 tpd, Cu-Zn operation at Ruttan utilizes 49 model 120A machines. The plant started operation in May, 1973.The 4-impeller model 120 flotation cell has been marketed by Galigher since the early 1960's but the single impeller model 120A is relatively new.Model 120 Agitair -Cell DataThe Model 120 (Dwg. 1) has floor dimensions of 101 x 10' and a lip height of 2~ to 4 feet to provide up to 400 cubic feet of volume. This machine is shown with a froth crowder and stabilizer plates which are optional.Each motor drives two agitators. 20 HP is recommended by Galigher but 25 HP is more realistic with massive sulphides. The SG of ?ox ore is about 3. 6.The Model 120 can handle up to 600 cubic feet of air per cell at 2 psig which requires 5-6 HP at the blowers. Air volume to each impeller is controlled by a valve from a main header.During the first 3 years of operation at Fox there were few mechanical problems with the 120's."

Jan 1, 1974

By L. Voisin, G. Damm

"In order to develop a new pyrometallurgical process for eliminating detrimental arsenic and antimony from the impurity-rich matte produced from copper concentrate, and for treating the occasionally generated speiss in nonferrous smelting processes, the phase relations in the Fe-Cu-S-As-Sb system saturated with carbon at 1473 K were investigated. The distribution of elements between the condensed phases at the miscibility gap, where three equilibrated phases of iron-rich alloy, copper-rich alloy, and matte coexist, were also studied. The investigation was carried out by performing a series of laboratory scale experiments in an electrical furnace at 1473 K, followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Inductively Couple Plasma (ICP), Atomic Absorption Spectroscopy (AAS) and Carbon Infrared Spectrometry (CIS) techniques.The results were compared with previous investigations for the Fe-Cu-S-As-C and Fe-Cu-S-Sb-C systems and discussed on the basis of the molar fraction distribution for both arsenic and antimony in the matte phase at five different matte grades. It is expected that by using this phase separation technique it might be feasible both, the cleaning of a complex copper matte and the elimination of arsenic and iron together with an acceptable amount of antimony into the iron-rich alloy phase, which can be discarded as a harmless and smaller deposit."

Jan 1, 2014

By J. W. Smith, J. G. Eacott, D. H. Napier

"Three hydrometallurgicat processes (Noranda chloride leach, B. C. Research biological leach and Sherritt-Cominco activated oxygen leach) and the Noranda pyrometallurgical process have served as the basis for design projects in the final year of the chemical engineering program at the University of Toronto. Each member of a team of five or six students devotes about 200 hours to the project and the final report is expected to include an economic analysis.None of the processes has been developed to full- scale plant, nor, in the case of the B.C. Research and Noranda processes, were pilot plant data available. Nevertheless, the designs developed provide a useful basis for a preliminary estimate of capital and operating costs and for a preliminary assessment of project feasibility.This paper discusses the approach used in the design projects with respect to engineering and economic aspects, and outlines the educational features and benefits of such a program as well as some of the problem areas that arise.IntroductionAs part of the undergraduate degree course in chemical engineering at the University of Toronto, students devote some 200 hours to a design project in their final year. Hydrometallurgical processes, not yet proven at the commercial scale, have been selected for study. The students are required to develop laboratory and / or pilot scale results into a conceptual plant design, using sound engineering principles. Capital and operating costs are then determined and a preliminary feasibility study and economic analysis are carried out."

Jan 1, 1986

By A. B. Rossetti

"THE MISSION TO Offshore Scotland was in my opinion a very worthwhile venture, as it indicated the scope of the offshore oil and gas business and how we might exploit it to the fullest here in Nova Scotia - if our offshore fields eventually become producing fields. The writer was able to attend a considerable number of lectures and as a result gained some valuable know-how on the engineering design, financing and operation of the North Sea oil industry. There are many new fields of technology that had to be developed to overcome the North Sea's hostile environment and a great deal of the same technology will have to be developed to win oil and gas from our continental shelf. The visit left me with several impressions, which in the main are:(1) The high order of investment required to develop offshore oil. The investment ranges from 10 to 20 times that required for a similar output on land. Each barrel of oil costs on the average of about $2,- 500 per barrel per day.(2) Because of the high investments required, before the first oil is produced the field must be brought into production at the earliest possible date and initial lead time from decision to production is less than four years. In the British Petroleum field, working at a depth of 450 feet will require an investment of $900,000,000 to develop a production of 400,000 bbl per day. (3) The size and complexity of equipment required is beyond anything ever imagined. Problems which must be overcome are such factors as water depth, wind velocities, wave height, wave period, long periods of darkness, low temperatures, distance from land, and fog."

Jan 1, 1973

By S. Hill

For a mining operation, the determination of the best place to build haul roads is typically done by hand, or with the assistance of rudimentary shortest path optimisation algorithms. Straight line, point to point, modelling of costs is often used with distances multiplied by constants that are based on rise of the road between the points. Failings of this approach are that straight line approximations are notoriously poor as they do not take into account areas where a truck cannot travel. In addition, the rise and fall of the road may vary considerably over the truck journey meaning acceleration/deceleration and varying truck speeds are not taken into account. Lastly, the use of rudimentary optimisation algorithms means properties a truck must obey such as minimum turning circles, line of sight restrictions or even that the truck must travel forward at all times are not taken into account. Thus solutions generated may not be feasible, let alone optimal. In this paper we discuss a state of the art parallel Artificial Intelligence tree search technique for solving haul road location problems. As well as the above properties, factors such as road utilisation, cut and fill, and construction costs are taken into account. The combination of advanced modelling and fast computing and optimisation techniques produces significant benefits both in terms of time to generate roads and cost savings. Preliminary results where this method has been used are discussed.

Aug 1, 2013

By Yin Guangzhi, Song Zhenlong, Li Minghui, Li Wenpu, Deng Bozhi

"Darcy's law is widely used to describe the oil and gas flow characteristics in the multi-pore media reservoir. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the high-velocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore. The gas flow velocities in coal in different deformation stage under different gas pressure gradient were tested and the relationships between gas flow velocity and gas pressure gradient were discussed, which can help us to investigate the transformation conditions of gas linear flow and gas nonlinear flow in coal. The results showed that the gas flow in the coal under low effective stress environment can be described by Darcy's law. The low-velocity non-Darcy flow of gas gradually occurred and the start-up pressure gradient increased in the coal as the effective stress increased. The low-velocity non-Darcy flow of gas also occurred in the coal at the yield deformation stage, however, the start-up pressure gradient decreased as the effective stress increased in this stage. In post-peak stage, the highvelocity non-Darcy flow of gas occurred in the coal under low effective stress environment. The gas flow in the coal gradually returned to be Darcy flow as the effective stress increased. The mechanism of the phenomenon is discussed based on the experimental results. The research results can be used to guide well test analysis and prediction of oil-gas production. INTRODUCTIONThe oil and gas flow in original multi-pore media reservoir are usually regarded as steady and linear processes and can be described by Darcy’s law. However, the low-velocity non-Darcy flow of oil and gas occurs in the multi-pore media reservoir under low permeability conditions. Meanwhile, the highvelocity non-Darcy flow of oil and gas occurs in the multi-pore media near the wellbore or workface. The gas flow in the multi-pore media even may be unsteady under some conditions such as gas emission and outburst.The phenomenon of underground water low-velocity flow in clays was deviated from Darcy’s law was found in the end of the nineteenth century (King, 1898). The deviation from Darcy’s law was later reported and investigated more (Swartzendruber, 1962; Miller and Low, 1963). These researches revealed that the start-up pressure gradient exists under low permeability conditions. Klinkenberg (1941) proposed that the permeability constant as determined with gases is dependent upon the property of the gas, and is a linear function of the reciprocal mean pressure. This effect can be explained by taking into account the phenomena of slip, which are related closely to the mean free paths of the gas molecules."

Jan 1, 2015

By C. G. McLachlan

Professor H.E.T. Haultain: To me from time to time the urge comes to say the agreeable thing as well as the disagreeable in commenting on the work of others. It is a prerogative of age. I don't apologize. To myself I justify my action as based on a long experience of the matters with which I deal, and I like to tell myself that I have a certain responsibility in such matters on account of my detached position. This Noranda article is a very fine contribution concerning Canadian milling, and I am surprised that no word of commendation or thanks has appeared concerning it in the BULLETIN. There is altogether too much written in these days by men rushing into print, concerning laboratory work, that has not been tied into, nor has resulted in application in the field. The authors of this paper have not rushed into print. The preparation of this paper was evidently an uncongenial task. If the authors had been that way inclined, it could have spread over several lengthy papers. It is an important article because it represents an enormous amount of work in the laboratory and the mill, extending over a period of sixteen years, and resulting in fine metallurgical and economic results with a very difficult and involved problem. It is a fine article because it is so well prepared and presented. It deals with an unusual ore condition, but there is much in it of use to every cyanide millman. It leaves very little room for criticism, though there may be differences of opinion in regard to some of the chemistry phases with which I am not conversant. I am struck by the enormous amount of persistent, painstaking, conscientious research work involved, and in the careful, sincere way in which the methods and difficulties have been described. Persistence and sincerity are the key note of the effort. It should have a good educational effect on the rising generation of millmen, and it should continue for long as a work of reference, and a spur to others. There has been an important by-product, the training and development of the young men engaged in the work. Three of them became superintendents of important mills. One was sought for important work in Africa, another has joined a large research organization in the United States.

Jan 1, 1946