Search Documents

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By A-A. Bogno, M. Rappaz, J. Valloton, H. Henein

"Rapid solidification of Al-Cu droplets of eutectic composition was carried out using Impulse Atomization in an argon atmosphere, to study the microstructures forming at different cooling rates and undercoolings. Two distinct morphologies were observed within the investigated Al-33wt%Cu droplets microstructures: (i) A regular lamellar morphology and (ii) an undulated morphology. The volume fraction of each type of morphology was measured as a function of the droplet size and the nucleation undercooling was deduced using the hypercooling limit equation. The scale of the microstructures was determined through measurements of inter-lamellar spacing across and along the growth direction. Growth velocity and undercooling were deduced using Jackson and Hunt (1966) eutectic growth theory. Finally, mechanical properties were estimated through micro-hardness analysis using a Vickers hardness tester, revealing exceptional properties for an aluminum-copper alloy. Indeed, the hardness values, increasing with growth rate and undercooling, were 3 times higher than the values obtained in hypo-eutectic Al-Cu alloys.INTRODUCTION Eutectic alloys are very attractive due to their good fluidity allowing ready shaping of parts in casting processes as well as in thermal spray deposition. In addition, they yield microstructures with high mechanical properties, by the virtue of their scale/size which is defined by the solidification parameters and the thermodynamic and thermophysical properties of the given alloy. Therefore, it is important to understand the relationship between the microstructures and the solidification parameters of eutectic alloys in order to control their solidification path and mechanical properties. The latter could be improved by either adding an appropriate strengthening component to a base eutectic material (Böyük, MaraslI, Kaya, ÇadIrlI, & Keslioglu, 2009) or by refining the microstructures for more effective dislocation pinning (Campbell & Campbell, 2003). Tailoring the microstructure can also be beneficial to chemical (Freitas, Osório, Spinelli, & Garcia, 2014; Osório, Freire, Caram, & Garcia, 2012) or electrical (Kaya, 2012) properties of the material. Eutectic-type microstructures, usually formed from liquid (eutectic transformation) or solid (eutectoid transformation), are made up of two or more different phases, generally of lamellar or fibrous (rod like) morphologies (Kurz & Fisher, 1998). In general, a binary eutectic structure can be regular (when both phases are non-faceted) or irregular (one of the two phases is faceted), the two solid phases having roughly the composition of the liquid from which they are formed."

Jan 1, 2017

By Ian Ewart, Trevor Bergfeldt, Gourab Satapathy, Ajay Patel

"Conventional electrowinning (EW) of nickel from sulfate electrolytes is complicated by several factors including the requirement for a diaphragm cell to separate the anolyte and catholyte and the need to minimize nickel mist emissions. Developed and commercialized by emewCorporation, this novel process electrowins high purity nickel cathode (99.5%) from copper refinery bleed streams using the proprietary emew vortex EW technology. The emew nickel process incorporates high flow rate in an enclosed cylindrical EW cell operating at high current densities that overcomes the challenges of conventional nickel EW and completely eliminates the risk of nickel mist emissions. The tubular cathodes are easily harvested and mitigate the effect of plating stresses inherent in nickel EW. The present paper describes the emew nickel process and its most recent application to copper refinery bleed streams at full-scale.INTRODUCTION To meet the stringent demand of customers, nickel producers are giving prime importance to production of high purity nickel cathodes. The major challenge for refineries is to improve cathode quality and appearance despite fluctuating electrolyte impurity levels. The basis of achieving good quality cathode includes the control of electrolyte impurities and consistency of specific process conditions. The commercial operation of emew nickel technology has been successfully implemented and has demonstrated the ability to produce high quality nickel cathode from refinery bleeds. This paper emphasizes the importance of upstream impurity removal to achieve the required nickel emew feed composition by evaluating the benefits of using selective precipitation as a purification scheme with the aim of improving the overall nickel recovery while ensuring suitable nickel concentration in the advanced electrolyte is achieved. Nickel electrowinning is similar to other electrowinning processes that employ insoluble metal anodes & cathodes. It requires the passage of direct current between two electrodes that are immersed in a conductive, aqueous solution of nickel salts. For the recovery of nickel from solution, the most common methods are electrowinning and hydrogen reduction. Electrowinning usually occurs from sulfate, chloride or mixed sulfate/chloride electrolytes. In sulfate electrolytes, nickel electrowinning cells are normally designed to achieve specific criteria as outlined below (Robinson & Tuppa, 2002):"

Jan 1, 2017

By W. Keith Buck

Introduction During World War II years, the magnetometer was used by various field parties of the Geological Survey of Canada, specifically in the search for chromite, a strategic war mineral. Throughout the summer of 1944, Professor J. W. Ambrose used the instrument experimentally on eight separate projects (1). Since then, several members of the Survey have come to consider its use to be of valuable assistance in the season's mapping. Dr. C. H. Stockwell, in particular, regards use of the magnetometer as a necessary part of detailed geological survey work. Throughout the field season of 1949, the magnetometer was used by Dr. Stockwell?s party as an aid to mapping in detail, to the scale one thousand feet to the inch, the south-west quarter of Dasserat township, Temiskaming county, Quebec. The principal geophysical project that was undertaken was the location of the Horne Creek fault and the Diabase fault in the area approximately midway between Arntfield and Kearns, on the Quebec side of the Interprovincial border. The location of these faults on either side of this central area was known. The Horne Creek fault is a subsidiary fault to the Cadillac 'break' which extends ?westward from Val d'Or through Cadillac to beyond Larder Lake. It lies to the north of that major fault zone and has a general southwesterly trend.

Jan 1, 1951

By Malcolm Scobie

"This paper reviews the evolution of Canadian surface and underground mining automation, principally relating to: advances in communications, initial development of machine teleoperation from line-of-sight remote control, and islands of automation. The eventual role of teleroboties and minewide robotic mining remains to be resolved. The progress and approaches adopted have tended to vary within each sector of the mining industry. Recent information technology advances have made possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using new communications technology. The Digital Mine will provide the information infrastructure to serve as the foundation for minewide automation. This paper concludes by reviewing the issues likely to govern implementation success, relating to: mining process design, machine design, machine intelligence, and mine planning and control.IntroductionSignificant advances have recently been made in underground hardrock mine communications and teleoperation. Subsequent R&D efforts are mainly focussing on control systems for various types of machines. In underground potash mining, the realization of automated continuous mining systems appears to be imminent. Recent advances in surface mine dispatching, machine monitoring and global positioning systems (GPS) have tended to reactivate some of the initial R&D enthusiasm developed in the '70s for surface mine automation. Mines at large are approaching a major milestone: the implementation of comprehensive communications infrastructure which proves to be sufficiently reliable and economical to support the automation of routine mine production, either using teleoperated or autonomous machines. This then should motivate a deeper commitment to real time monitoring and management. The communications advances make possible the Digital Mine; in which information associated with all mining processes, however dispersed, would be integrated with support systems using information engineering. The Digital Mine will provide the information infrastructure to serve as the likely foundation for a wide range of automation scenarios. This paper surveys the status and directions of automation development in both surface and underground Canadian mines, pointing to what are seen to represent key technology development issues."

Jan 1, 1995

By E. Ghali, W. Zhang, C. Su, N. Sorour, G. Houlachi

"Zinc electrowinning process is sensitive to the presence of metallic impurities such as lead ions that could substantially and negatively affect the power consumption and surface morphology. Effect of various concentrations of manganese ions and traces of lead ions up to 2.5 mg L-1 added to the electrolyte during electrowinning have been investigated by electrochemical polarization techniques such as galvanostatic, cyclic voltammetry and potentiodynamic. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were applied to examine the surface morphology and crystallographic orientation, respectively. Microwave plasma-atomic emission spectrometry has been used to determine the lead content in the deposit and in the electrolyte after electrodeposition. It was found that lead ions added to the zinc electrolyte led to the increase of cathodic overpotential and current efficiencies of zinc deposit. However, addition of Mn2+ into the zinc electrolyte resulted in the decrease of cathodic potential and current efficiency of zinc deposit. It can be stated as example that galvanostatic polarisation at 40?C and 52.5 mA cm-2 in presence of lead up to 0.1-0.2 mg L-1 in the electrolyte and 8-12 g L-1 Mn could be better considered as practical working parameters for electrowinning process.INTRODUCTIONApproximately 85% of the global production of zinc metal is produced by electrolytic process (Sinclair, 2005). The main goal of the zinc plant is to obtain pure zinc deposits with high current efficiencies. Smooth and pure deposits with high current efficiency (CE) are always obtained from pure electrolytes (Alfantazi & Dreisinger, 2001). The presence of metallic impurities in the zinc sulphate electrolyte is a major problem for the zinc electrowinning industry, since decreases in current efficiency, changes in deposit morphology and cathodic polarization are observed for electrolytes containing small concentrations of impurities (Ault & Frazer, 1988; Muresan, Maurin, Oniciu & Gaga, 1996). Low level concentrations as parts per million of these impurities are reported to influence negatively the zinc electrodeposition (Beshore, Flori, Schade & O'Keefe, 1987)."

Jan 1, 2016

By J. R. Foster

Investigations into the effect of a variety of acid digestions on common rock-forming minerals demonstrated a considerable variation in the proportion of the total metal extracted. A similar situation applies to the analysis of a number of common rock types. In addition, grain-size variation has an effect on the amount extracted by certain digestions. This work indicates that considerable care needs to be given to selecting an appropriate acid digestion capable of determining metal held in particular components of a sample. By using partial extraction techniques, the identification of certain patterns of metal distribution, undetectable by normal methods involving total metal analysis, may be achieved.

Jan 1, 1973

By E. G. Joe

"The continuing increase in costs for power and fuel are affecting significantly the cost for milling of Canadian ores. In order to ascertain the scope and source of energy consumption in Canadian mills for further energy conservation opportunities, CANMET, in cooperation with the Canadian Mineral Processors carried out a detailed survey on the metallic mineral processing plants. Sixty-seven mills representing almost 300 million tons of annual capacity participated in the survey. The results indicated that in general, copper and iron ore mills, representing the bulk of the tonnage, consumed relatively low levels of energy per ton. Nickel-copper, zinc-copper and lead-zinc ore mills were moderate in energy consumption, while uranium and some copper-lead-zinc mills reported much higher energy consumptions due primarily to the increased heat requirements of the ore pulp. While the plant heating costs varied somewhat with the location in Canada, it was apparent that the lowest heating costs were achieved by those built with proper insulation and energy conservation design. If the cost per million British Thermal Units is taken as $2.00, the mill energy costs generally ranged from 40¢/ton up to $1.20/ton.IntroductionEnergy consumption in milling has always been of significant interest to Canadian mineral processors who traditionally calculate their milling costs down to pennies per ton. Even the measure of an ore's grindability is expressed empirically by Bond in kilowatts hours per ton milled. Some of the mills located in isolated areas were obliged to generate their own electrical energy from fossil or petroleum-based fuel at a cost substantially higher than that obtainable from captive or public hydro-electric installations. These mills practiced energy conservation long before the advent of O.P.E.C. energy cost inflation. One example of this was the use of electric boilers to produce process and heating steam during off-peak electrical load periods."

Jan 1, 1978

By Hans Chr Andersen

Almost every form of iron ore and carbon material has been used as a raw material in the production of pig iron in electric reduction furnaces. Experience derived from the operation of the large 33,000-kva. Tysland-Hole furnaces, however, indicates that production results are very much influenced by the raw material conditions. The author presents the principle pattern of the metallurgical structure of the interior of an electric pig iron furnace. On the basis of this, he discusses the variations of electrical and metallurgical conditions for the process which will take place with changing raw materials. The formation of a coke bed underneath the electrodes, and its influence on the furnace operation, is illustrated. Quality and grain size of the coke added to the charge will influence the build-up of the coke bed and will thereby also affect the electrical re-''Elektrokemisk A/S, Oslo, Norway. resistance and reduction potential in the furnace.

Jan 1, 1963

By Y. Rama Murthy, Amit Ranjan, Pankaj Satija, Sunil K. Tripathy

"Chromite ore is one of the essential raw materials for ferroalloy and steel industry. Boula-Nuasahi belt of Sukinda region, Odisha, is the only resource of chrome ore in India. The Indian deposits are typically characterized as ferruginous and siliceous type ores. Chrome ore is generally mined by open cast mechanized mining method in these areas. The run-off-mine (ROM) ore from the various mines is sent to beneficiation plant via stack yard for further up gradation. The chrome ore beneficiation plant (COB) has two major circuits: comminution (feed preparation) circuit and beneficiation circuit. In the comminution circuit, the ore is reduced to <1 mm size ( for complete liberation of chromite) from -220 mm size in stage wise crushing (primary and secondary crusher) followed by screening and single stage grinding in a ball mill. Fraction having size <1 mm is further upgraded in the beneficiation circuit to produce three different concentrates having specific chemical composition and Cr: Fe ratio. The beneficiation plant is a complex circuit comprising of combination of unit operations (spiral concentrator, Floatex density separator, hydrocyclone, wet shaking tables). In the recent years the overall performance efficiency (grade and recovery) of the beneficiation circuit got affected with numerous changes in the run-off-mine ore quality (physical and chemical), mineralogical composition, etc.In this article, attempts made for improving the performance of chrome ore beneficiation circuit is discussed. The approach adopted and practical problems encountered while the process were also highlighted. The results of the trials has shown an improvement in the performance of the cyclone (d50 : 56 µm – 40 µm) and chromite losses into tailing to <12%.INTRODUCTIONChromite has a wide range of application, from refractories to metallurgical industries, and from chemical to non-ferrous alloy industries. Chromium ore (Fe2+, Mg) [Cr, Al, Fe3+]2O4) occurs exclusively in rocks formed by the intrusion and solidification of molten lava or magma which is very rich in the heavy, iron containing minerals such as pyroxene and olivine. With the richness of silica and iron, the chrome ores are broadly classified as siliceous type and ferruginous type. Pure chromite with composition FeCr2O4 is rare because magnesium usually substitutes for ferrous ion and aluminum and ferrous ion substitutes for chromium. Generally the associated gangue minerals are talc, quartz, hematite, goethite, limonite, gabro, serpentine, anorthosite, dunite, pyroxinite, etc. Around 96% of the chromite ore production is consumed for metallurgical applications of which 94% is converted into different grades of ferrochrome i.e., high carbon ferrochrome and charge chrome as shown in Figure 1. Stainless steel being the leading consumer of ferrochrome, any change in the dynamics of the stainless steel industry impacts overall chrome ore demands significantly."

Jan 1, 2016

By Olaf Kessler, Jan Kalich, Michael Reich, Julia Osten, Uwe Füssel

Modern automobile bodies consist of different materials, e.g. aluminium alloys and high strength steels. Mechanical joining, e.g. clinching, is very suitable for joining aluminium and steel sheet. But clinching needs a sufficient ductility, which is no longer supplied by high strength steels. Laser-assisted clinching has been shown, to be able to join aluminium and high strength steel sheet successfully. Thereby the steel sheets were heated locally for short times to increase their ductility. Due to the thermal contact between steel and aluminium sheet the aluminium alloys also achieve a local short-time heat treatment. This fact may cause a significant impact, as aluminium sheet in automobile bodies is often used in T4 (or similar) condition and later artificially aged during the paint bake cycle. Aluminium alloys 6016 and 6181 have been short-time heat treated with heating rates up to some 100 K/s. Precipitation and dissolution processes have been monitored in-situ by calorimetry. Mechanical properties have been investigated on as well as after short-time heat treatment by deformation dilatometry. The results show, that suitable short-time annealing parameters during laser-assisted clinching can increase ductility and at the same time act as retrogression for aluminium sheets, resulting in increased strength after aging.

Jan 1, 2015

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By E. S. Allen, P. R. Kruesi, J. L. Lake

An electrochemical process is described for converting concentrates of base-metal sulphides to the corresponding pure metals and elemental sulphur. The application of the process to chalcopyrite is discussed. The process is also of potential interest in processing copper-nickel sulphides, and laboratory data concerning this potential are presented. The process creates neither air nor water pollution.

Jan 1, 1973

By H. Tokuichi, H. Ohta, K. Sato

A physical separation technique of tantalum capacitors from waste print circuit boards is in a development phase in Japan. A tantalum capacitor consists of an exterior coating of resin (epoxy resin) mixed with silica fillers and a sintered tantalum compact, the latter of which is impregnated with manganese dioxide (MnO2). In this study, we developed a process to recover tantalum oxide from tantalum capacitors by roasting, fluidized-bed separation, and hydrometallurgical treatments. Our aim was to recover tantalum oxide with high purity from waste tantalum capacitors. In this process, the exterior resin was selectively decomposed by roasting without oxidation and pulverization of the sintered tantalum compact at a proper temperature. Furthermore, the decomposed resin with silica filler on the surface of the sintered tantalum compact was mostly removed by fluidized-bed separation. The surface of the sintered tantalum compact was cleaned by ultrasonic irradiation in an acid solution to remove the MnO2 paste as well as residual Ag paste and silica filler. The impregnated MnO2 in the sintered tantalum compact was leached as Mn(II) ions using acid solutions via the reducing effect of tantalum metal to recover purified tantalum oxide.

Jan 1, 2014

By Patrick E. Cavanagh

"A pilot shaft furnace was operated for one year at Steep Rock to produce special high-grade products from coarse ore, using lignite as fuel. The furnace is 10 ft in diameter and 60 ft high. When operated to heat coarse Steep Rock ore to drive off combined water and give a 64-per-cent-Fe product, the fuel consomption was 900,000 Btu's per long ton of product. The furnace was run in this way from September 1966 to January 1967 to establish the technique of feeding and discharging the furnace and controlling the gas composition and temperature. The furnace is similar in operation to a lignite water gas producer containing a large proportion of catalytic iron oxide. Steam injection is used to control the temperature. The product was tumbled in a rotary trommel to stabilize it. The resulting fines could be fed to the conventional pellet plant at Steep Rock. The furnace was next operated to make 77-per-cent-Fe metallized coarse ore. Several major modifications in de-sign were made and the furnace was successfully operated for short periods to maintain the required conditions to remove 75 per cent of the oxygen from the ore to give a 75-per-cent-reduced product at a grade of 77 per cent iron. The furnace cooling zone was operated under positive pressure, with internai alkaline water sprays to cool the charge. The product was discharged from the open bottom of the furnace without serions reoxidation. The metallized ore was magnetically separated from the discharge. Most of the charred lignite discharged along with the ore is re-cycled. Fuel requirement was 11,000,000 Btu's per long ton of product. This metallized coarse ore is intended for blast furnace feed. A short test run was carried out to establish the conditions for making a highly reduced melting stock for steel furnaces. To achieve 90 per cent reduction and over 90 per cent Fe, the furnace must be slowed down so that the production rate is about one-half the rate when making a 75-per-cent-reduced metallized product. Fuel requirement is 15,000,000 Btu's per long ton of product. The simple shaft furnace developed is similar to the top half of a blast furnace, with some major modifications to allow discharging into the open air. This Low Temperature Blast Furnace program has been technically successful and has resulted in making data available for the design of a commercial plant. Study of the commercial feasibility of large-scale production of metallized coarse ore at Steep Rock is still continuing."

Jan 1, 1968

By J B. Magee

Sheep Creek Mines Limited has developed several operating techniques that have greatly assisted in keeping unit costs at reasonable levels. Some of the techniques, as described in this paper, include organization, accounting, warehousing, bonus and contracts. INTRODUCTION THIS paper is a non-technical report on operating techniques developed by Sheep Creek Mines Limited at their Mineral King mine, located near lnvermere, B.C. Depressed metal prices and continually rising labour and materials costs have necessitated a continuous search for method to keep operating costs down. The newly developed techniques and practices have greatly assisted in maintaining unit costs. Sheep Creek Mines Limited is a mining company incorporated under the laws of the Province of British Columbia. The Company&apos;s share capital is 3,500,000 common shares, witl1 a par value of 50 cents each, of which there are 1,875 000 shares is-sued. The Company has eight di-rectors. The administration, exploration and accounting offices are located in Nelson, B.C. The Company&apos;s working capital is approximately $1,500,000.

Jan 1, 1963

By A. E. Wraith, J. Protheroe Jones, P. J. Mackey

INTRODUCTION When Victoria became queen in 1837, that technical wonder of the 19th century—electricity— had progressed from being an exciting physical curiosity and was now a field of intense scientific investigation, invention and application. Its role in electrochemistry had been brilliantly quantified by Faraday in 1833–1834, and his earlier discoveries in electro-magnetism were to lay the foundations of electricity generation and the electric motor. In this age of electrical experiment, silver electro-plating emerged as a popular decorative art, at first using batteries to provide the deposition current, superseded by dynamos in the early 1840s. The decorative chemical and electroplating of precious metals was largely pioneered in England by the firm of G.R. Elkington and Co., founded in Birmingham by George Richards Elkington (1801–1865) in 1832, and protected by a series of patents which helped the company establish a leading position in the new field of ‘electrometallurgy’. In the same decade, the technique of electrotyping emerged, the first application of electro- forming by electrolytic deposition. Simultaneously invented by Spenser in England and Jakobi in Russia, but generally claimed for Jakobi, electrotyping involved plating a thick copper layer on to an electrically conducting mould wall embossed or incised with a pattern or profile which would consequently be replicated on the copper deposit—essentially a method of casting by electro-deposition with the mould wall as cathode. Woolrich’s invention of the low voltage magneto-dynamo in 1842 eliminated the need for batteries as a continuous source of deposition power, opening up the possibility of making more massive electroplated deposits, and by the mid-point of Victoria’s reign in 1869, the work of Wilde, Wheatstone and Siemens had produced the self-excited electro-dynamo, capable of higher voltages and yet greater deposition power. In this early Victorian period copper was extracted and refined by methods which had developed step-by-step over many decades. Only relatively rich copper ores containing more than, say, 6% Cu were economically useful, and the final copper product was far from pure. Copper production in Britain was located principally in the Swansea area of South Wales, based upon the ‘Welsh process’ of reverberatory batch smelting and refining, using locally mined coal and ore imported from Cornwall and elsewhere. Silver was an important by-product. Much of the output was exported and South Wales remained a principal supplier to the world copper market until the 1890s. It was here at Pembrey, a few miles west of Llanelli, that a new primary copper smelter was stablished in 1849 under the name Mason and Elkington, arguably to supply the Elkington company’s market for electrotype products.

Jan 1, 2019

By Funsho K. Ojebuoboh

With several “green” applications on the horizon, bismuth has become an even more important minor metal in the smelting and refining of lead. Smelters with a complex sulphide feed invariably deal with bismuth. Its behavior during the smelting of lead in conventional sinter-blast furnace operation is discussed. Because it readily deports to the lead phase during the refining of lead, its separation from refined lead remained unsatisfactory in early lead production. When commercial requirements of bismuth in lead became more stringent early this century, the procedure where by calcium and magnesium is used todebismuthise lead was developed. The present conduct of this 1936 process, the Kroll-Betterton process, is discussed with emphasis on operational improvements.

Jan 1, 1996

By A. M. Hadian

The use of dolomite refractories in steel making and cement industries has advantages over other basic products particularly in countries where this type of refractories is produced. Due to existence of high-quality dolomite deposits in many regions of Iran, there is a good potential for producing dolomite refractories in the country. This study focuses on the effect of such additives as iron oxide and alumina on hydration resistance and density of Iranian dolomite. It was found that addition of Fe2O3 is more effective than Al2O3 on increasing density as well as resistance to hydration of dolomite.

Jan 1, 2004

By O. A. Ojo, E. Anisimov, A. K. Khan

Electro-spark deposition (ESD) has recently generated a great deal of interest in processing aerospace materials. This is due to its potential for joining and repairing difficult-to-weld precipitation strengthened nickel-based superalloys without having problems of welding cracking that often plaque these materials. The short duration of current pulses involved in the process combined with the intermittent contact results in extremely rapid thermal cycle that produces nearly no heat affected zone in the substrate material. The microstructure of electro-spark deposited superalloy was meticulously studied in this work by scanning electron microscopy (SEM) and analytical transmission electron microscopy (TEM). The results show that in contrast to general assumption, the extreme rapid cooling rates involved in the ESD process did not produce partition-less solidification that is devoid of second phase microconstituents in the material. The secondary microconstituents were found formed along the intercellular regions of the solidification microstructure. The nature of these particles and the possible implication of their formation on mechanical properties of ESD processed material are reported and discussed.

Jan 1, 2015