Search Documents

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

"The Kidd Creek concentrator is situated adjacent to Highway 101, twenty-four kilometres east of the center of the city of Timmins, Ontario. Sulphide ore, received by train from the minesite twenty-nine kilometres away, is processed at a rate of twelve thousand metric tonnes per day. Saleable concentrates of copper, zinc, lead and tin are produced.The concentrator contains secondary crushing, grinding, flotation, gravity separation and concentrate handling facilities. The total concentrator manpower complement is one hundred and sixty-four which includes supervision and operating personnel. Twenty-one shift personnel are required to operate the processes involved and they occupy fifteen different operating positions in addition to that of the supervisor. These positions include:1 Central Control Operatorl Metallurgical Leader1 Dryer Control Operatorl Crusher Leader3 Copper-Lead-Zinc Flotation Circuit Operators1 Pyrite Flotation Circuit Operator1 Tin Plant Operator2 Grinding Operators1 Concentrate Operator2 Crusher Operators1 Spare Operator1 Tailings Area Operator1 Automatic Sample System Operator1 Dryer Area Helper1 Crusher Helper1 Tin Plant Helper"

Jan 1, 1981

By E. S. Moore

GOLD was discovered previous to the year 1900 on the east shore of Emerald lake, Afton township, Timagami Forest Reserve. It was found in a small cavern in banded iron formation, close to the water's edge. This occurrence of gold was mentioned in several reports that referred briefly to this area, and prospectors evinced considerable interest in the region. It was not, however, until the Golden Rose Mining Company, which was incorporated in 1909, started operations that much work was done on the property. In 1915-16, this Company, under the direction of E. J. Townsend, the President, did a considerable amount of work. A small mill was built and ore was extracted from pits, trenches, and a one~ hundred-foot shaft. In 1927, Afton Mines, Limited, was incorporated to take over the property, and about thirty men were employed for a time. During 1934, the New Golden Rose Mining Company was organized to handle the property, and the Consolidated Mining and Smelting Company of Canada, Limited, undertook to develop the mine. In March of the following year, this Company began deepening the shaft from 100 feet to 500 feet. A considerable amount of drilling had previously been done on the hill of iron formation in which the mine is located. Further drilling was done from the surface, and altogether about twelve holes have been put down to test the formations. Over 2,000 feet of drilling has also been done from the underground workings. The mine is now known officially as the New Golden Rose mine, although to many it is better known as the Afton. To reach the property during the summer months, there is a boat trip of about thirty miles from Timagami, a wagon-road portage of one mile to Obabika lake, a boat trip of ten miles on this lake, and finally a wagon-road portage of one and one-quarter miles to Emerald lake. The mine lies about three-quarters of a mile down the east shore of the lake. A 75 h.p. Diesel engine and compressor were taken in over this' route last summer, and it is evident that the transportation problem is quite a serious one. Airplanes have been much in use, and a winter road runs from the mine to Chudleigh, on the .Canadian National railway near Sudbury.

Jan 1, 1936

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007

By M MacMillan

THE following is a brief description of the method of hoisting ore automatically at the No. 14 shaft of Mcintyre Porcupine Mines, Limited, Schumacher, Ontario. All ore and waste below the 3875-ft. level is hoisted up No. 14 shaft from the 7000-ft. level to the 3000-ft. level. Seventy to seventy-five per cent of the mining is done in this area. The shaft consists of four compartments: a man way, a ventilation compartment and two skip compartments. The hoist, located on the 3500-ft. level (see Figure l), is an 80-in.-diameter, 4-rope friction winder, utilizing two 6-ton front-dump skips in balance. The hoist is powered by a 1,100-h.p. A.C. motor, the maxi-mum speed being 2,400 ft. per minute. The operation can be either manual, push-button automatic from the pocket, or fully automatic. Men can be raised or lowered in the skips, using a collapsible aluminum platform placed inside the skip box.

Jan 1, 1963

By J. P. Bennett, W. E. Lee, S. Zhnag, K. S. Kwong

An EAF slag properly saturated in MgO results in increased refractory service life and steelmaking efficiency. A computer model was developed using phase equilibrium data from the MgO-CaO-SiO2-FeO, MgO-CaO-Al2O3-SiO2 and SiO2-CaO-Al2O3-FeO systems to predict MgO saturated slag chemistry. This model has been successfully applied to a commercial EAF, although disciplined plant practices are required to achieve benefits from slag chemistry control.

Jan 1, 2004

By R. B. Allen, E. E. N. Smith, B. C. MacDonald

"LocationTHE MAIN PROPERTY and townsite of Eldorado Mining & Refining, Limited, Beaverlodge Operation, is on the north shore. of Beaverlodge lake, •about seven miles north of the deserted town of Goldfields on lake Athabasca, and four hundred and ninety air-miles equidistant from Prince Albert, Saskatchewan, and Edmonton, Alberta. Both Eldorado Airlines •and Canadian Pacific Airlines maintain scheduled flights from Edmonton to the 4,000-foot airstrip on the north boundary of the Company property. Bi-weekly flights are made by Saskatchewan Government Airways from Prince Albert. Men and priority freight are flown by Company aircraft direct from Edmonton. From June to-September, when the waterways .are ice-free, freight is carried by barge from the •railhead at McMurray, Alberta, down the Athabasca river to Chipewyan, and across lake Athabasca to• Bushell, the terminal on Black bay, lake Athabasca, a total distance of 265 miles.The Eldorado Operation has been connected by a 12-mile, all-weather highway to Bushell. Where the highway crosses the park-land along the Fredette river, the townsite, Uranium, is under construction to provide services to the uranium-producing district. Spur roads have been built to the Ace, Fay, Eagle, •and Martin mines of the Eldorado operation, and to the properties of Pitch-Ore Uranium Mines, Ltd., and Rix Athabasca Uranium Mines, Ltd."

Jan 1, 1954

By I. Yarita

Magnesium alloys have the lowest density among the metals in practical use, and have properties such high specific strength, electromagnetic interference shielding and good vibration damping. Thus, there are many applications of these materials in automotive and electric parts. However, there is a little use of the products of metal forming of these materials because of poor plastic deformability in the normal temperature range and their high cost of production. To expand the range of application of products manufactured by metal forming, rolling technology for producing thin sheets having good mechanical and surface qualities is required. In this study, hot-rolled Mg-alloy sheets are experimentally rolled with or without lubrication in the temperature range from 293 K to 523 K. Rolling force, plastic deformability and surface quality are investigated, and the grain structures and their uniformity are observed. The effect of friction between the roll and the deforming material on the uniformity of the grain structure is discussed. Moreover, rolled materials are annealed and their mechanical properties are investigated by the tensile test and compared with those of as-rolled materials. The effects of the rolling conditions on the mechanical properties are discussed.

Jan 1, 2006

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By John Hartlen

"The 19th century was an ""age of gold"" and Nova Scotia experienced its share of early gold rushes. Gold mining activity in the province was focussed into three ""rushes"" which occurred, approximately, in the 1860s, 1890s and 1930s; a total recovery of 1.1 million oz. Au has been recorded. The purpose of this note is simply to chronicle the technical development of gold mining and processing in the province and to comment briefly on the recently renewed interest in this precious metal. The first public discovery of gold in Nova Scotia was made by a farmer in 1860 at Old Tangier or Mooseland, and this find sparked the province's first gold rush. The mining and milling methods of the 1860s were ingenious. Initially, arrastras, crude stone-hewn grinding mills, drawn by men, mules or horses, were widely used. Nova Scotia's first conventional stamp mill was installed at Mooseland by 1862; it was comprised of four wooden stamps and is believed to have been imported from Scotland. One of the largest waterwheels of the 1860s, reportedly 16 feet in diameter and 8 feet wide with a SO-horsepower rating, was used in the Renfrew Gold District to drive gold stamps. Steam power was also employed, and many of the engines were of native construction, as was the unit at Waverley's Lake Major Company, which had a piston 1 foot in diameter by 12 feet long and was connected to a 16-ftdiameter flywheel."

Jan 1, 1999

By David L. Sprott

This paper presents an evaluation of underground-to-surface haulage options for a relatively large deposit. Specifically, it presents a recommended haulage option to provide the greatest value to the Project. Options considered included conventional truck, trolley-truck, conveying and shaft hoisting. The work was done at the level of a preliminary assessment as input to an internal pre-feasibility study. The Base Case for the analysis in this study was a Long Hole Open Stoping option (LHOS) using conventional truck haulage. Two scenarios were considered for the evaluation and included: 1. The current resource to ~700 m depth. 2. An expanded resource to ~825 m depth. The haulage options evaluated included three trucking options, three conveyor options and two shaft options. The paper presents the results from evaluating these options within the two mining scenarios using a Discounted Project Cost (DPC) comparison. Recommendations are made for the options that will provide the greatest overall value to the project.

May 1, 2008

By J. R. Bradfield

THOSE familiar with the development of the Horne mine can readily appreciate that more and more accommodation bas been required for underground labour as the mine has grown. A permanent fire-proof change house, 30ft. by 75 ft., was built in 1927 to accommodate 194 men. This was extended ro 30 ft. by 92 ft. in 1928 to accommodate 296 men, and to 30ft. by 110 ft. in 1930 to accommodate 398 men. By 1933 this building was again overcrowded and tentative plans for a new change house were drawn up. However, it was realized that future operations would be centred around No. 4 shaft and a proposed new shaft, and the decision as to the location of the new change house had to be deferred until the area which seemed most suitable for the new shaft had been thoroughly explored underground. In the spring of 1934, the basic idea was accepted of drying the wet clothes in open mesh compartments or baskets located between rows of standard steel street-clothes lockers and built so that the covers or lids would serve as seats or benches.

Jan 1, 1935

By R. Therrien, L. Gosselin, J. Raymond

ABSTRACT: The ground-source heat pump is a low-carbon technology that uses the earth’s renewable geothermal energy to heat and cool buildings, with an ef?ciency 3 to 4.5 times that of conventional systems. These high performances are achieved by exchanging heat with the earth using a ?uid that is groundwater, surface water or closed loop water. Expensive installations, such as water wells or buriedcoils, are however necessary to transport the ?uid in and out of the earth, making ground-source heat pumps more costly than conventional systems. Installation costs can be reduced in mining environments due to the abundance and the accessibility of resources to be used with heat pumps. Examples of system design calculations using data from the Mouska and Doyon mines in Abitibi show signi?cant installation cost savings using dewatering mine water or ground heat exchangers installed below oxidizing waste rocks. Ground-source heat pump technology is reviewed and scoping calculations are presented to illustrate how such systems can be installed in mining environments.

Jan 1, 2010

By R. A. L. Drew, J. P. Immarigeon, F. Jalilian, M. Jahazi

In the present work TLP bonding of Inconel 617 is investigated. The influence of the main processing parameters i.e. time and thickness of the interlayer were studied with optical and scanning electron microscopy. Boron containing interlayers with two different thicknesses were used and the influence of various holding times from 5 min to 24 hours on the microstructure of the bond region was investigated. The results indicated that, for the testing temperature of 1065°C and holding times above 2 hours with an interlayer of 25.4 microns thick no liquid phase was observed. The same phenomenon occurred only after 6 hours for a 76.2 microns thick interlayer. Precipitate growth started at grain boundaries and continued inside the grains. The composition, size and morphology of the precipitates were studied using electron microprobe analysis. No noticeable changes were observed in the grain size of the base metal with increasing holding times.

Jan 1, 2004

By D. Paul Bishop, Kevin P. Plucknett, Hung-wei Liu

"Spark plasma sintering (SPS) process has been evaluated for producing the commercially pure (CP) Ti, TiAl and a TiAl-B4C composite. Comparisons were made between the materials in terms of the sintered density, resultant hardness and microstructures. In the present work, the titanium aluminide powders (Ti-48Al, producing a mixture of y-TiAl/a2-Ti3Al) were synthesised „in-house? using a simple reaction-sintering and mechanical attrition approach. This allowed various size distributions to be generated. The powders were then blended with a fine boron carbide (B4C) powder (up to 6 wt.%), and the resulting mixtures were consolidated using spark plasma sintering (SPS) under vacuum in graphite dies. An applied stress of 50 MPa was used for all SPS runs. The SPS parameters were varied in terms of the ultimate sintering temperature (up to 1300°C) and hold time (up to 10 minutes) for each material. It is demonstrated that high densities can be achieved this approach (exceeding 95% of theoretical, with optimised samples close to full density). Microstructural characterisation was conducted using optical microscopy, scanning electron microscopy, and X-ray diffraction. The B4C additions were seen to partially react with the TiAl to form reinforcements, such as TiCx and TiBx. Preliminary mechanical property assessment will also be briefly discussed.INTRODUCTION Titanium- and titanium aluminide-based alloys possess many unique properties, such as excellent corrosion resistance and high temperature strength, respectively (Cardarelli, 2001; Leyens & Peters, 2003). Compared to many other competing materials (e.g. stainless steel or Ni-based alloys), Ti- and TiAl-based alloys also have relatively low densities (~4.5 and ~3.9-4.1 g/cm3, respectively), which is critical for performance in aviation and automobile applications. However, the manufacturing cost is high, due to the expensive raw Ti material and difficulties in machining. TiAl-based alloys are particularly difficult to produce because of their limited ductility (Lütjering & Williams, 2007). To overcome those problems, powder metallurgy (PM) technologies have shown great potential as near-net shape processes for Ti- and TiAl-based alloys. The general PM process largely avoids laborious post-machining and minimises material use. In industrial production, the PM approach has been successfully utilised to manufacture aluminium- and iron-based alloys (Huo & Heath, 2008)."

Jan 1, 2017

By Sammy Bansah, Komla Dzigbodi-Adjimah

Abstract-Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized ("Banka") drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi- Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration programs for use in similar settings.

Jan 1, 1995

By Sammy Bansah, Komla Dzigbodi-Adjimah

Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized (“Banka”) drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi-Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration pro-grams for use in similar settings.

Jan 1, 1995

By Brian Lewis

"IntroductionThe leaching method selected for the dissolving of uranium ore depends in part on the physical characteristics of the ore, as well as the uranium mineralization. There are two main methods of leaching employed in uranium circuits in North America, one being ""Carbonate Leaching"" on sandstone, and pitchblende type ores, and ""Acid Leaching"", on quartzite type ores.This chapter deals with the acid leaching of uranium ores found in the Elliot Lake area, using sulphuric acid, for the leaching reagent, and ""pachucas"" for the contactor.The basic leaching process involves the pregrinding of the ore and the mixing of the ore with hot sulphuric acid, the mixture is air agitated, the air being used to oxidize the ore as well as produce agitation. The chemical reaction is as follows: Uranium Oxide + Sulphuric Acid = Uranyl SulphateThe following equations show the actual dissolution of the ""Hexavalent Uranium"", which show that more than one ion or complex of uranium is possible.Uranium DissolutionsI. UO, + 2H-(UOJ + H,O2. (UO,) + SO, = -UO, SO, (Uranyl Sulphate)3. UO, + SO,-(UO, (SO,),)=4. (UO, (SO,),)= -(UO, (SO,),)'Test work carried out in the laboratory as well as in the plants has determined the most efficient methods of extracting the uranium from the ore. A very important factor that has to be determined during initial test work are the amount of acid consumers in the ore. Within the Elliot Lake orebodies are minerals such as chlorite schist, diabase, and basement material, all very high acid consumers, consuming up to 1000 lbs. of acid per ton of ore. Of these minerals only the chlorite schist contain any uranium at all.The following are the operating parameters that have to be controlled in the plant:I. sulphuric acid concentration2. temperature of the mixture3. agitation4. liquid solid ratio5. reaction time6. particle size of ground ore"

Jan 1, 1989