Search Documents

By Gordon S. Farnham

THIS paper summarizes the results of investigations carried out at Sydney Mines, N.S., and at Ottawa, following the disaster at Princess colliery, December 6th, 1938. The Honourable Minister of Mines for Nova Scotia appointed A. E. Cameron special investigator to enquire into and report upon the cause of the rope failure. Public hearings were held in Sydney Mines and evidence taken from many witnesses. The site of the accident was examined in detail and investigations made of the rope layout and colliery practice. At the request of the special investigator, the Department of Mines and Resources, Ottawa, kindly undertook technical and scientific examination of the broken ends of the rope. These investigations were carried out in the Metallurgical Laboratories of the Department of Mines and Resources, under the supervision of G. S. Farnham, Metallurgist for the Department. Valuable assistance in interpretation of many features of the investigation was received from other sources. Acknowledgment is due to Messrs. Stuewe, McCall, and Gordon, and other members of the staff of the Dominion Steel & Coal Corporation; to Messrs. Morrison and Scott, and other members of District 26, United Mine Workers of America; and to Messrs. Timm, Parsons, Haycock, Haanell, and other members of the staff of the Department of Mines and Resources, Ottawa, for helpful ad vice and technical assistance in assembly of information, and preparation of material and interpretation of evidence obtained.

Jan 1, 1939

By Zuhair A. Nawab, Muhammad A. Al-Marhqun, Mehmet Guney

"The Atlantis-Il-Deep is a stratified metalliferous deposit located along the median valley of the Red Sea at a water depth of about 2200 m. The metal-bearing mud contains sulphides of zinc, copper and iron with significant amounts of silver, gold and cobalt. A variety of oxide, siliceous and carbonaceous gangue material is also present. Long sediment cores indicate that the thickness of the deposit may reach 25 m, but the average kriged thickness of metal-rich sediments is about 11 m.Mining geostatistics was applied to estimate the Red Sea offshore mineral resources. Experimental semi-variograms were computed along 0 ± 180 degrees and then models were fitted to analyze the mineralization phenomenon. Kriging estimates indicate that 696.330 million t of bulk sediments contain 1.891 million t of zinc, 0.425 million t of copper and 3. 75 thousand t of silver. Gold and cobalt contents were calculated from the analysis of solids in flotation concentrates as 47 t and 5368 t respectively. The significant outcome of implementing geostatistics to the Red Sea brine precipitates is not only for the evaluation of metal resources, but it also provides a useful tool in the optimization of selective dredging of appropriate areas to be mined. IntroductionThe discovery and extensive exploration of hot brines and hydrothermal sediments in the Red Sea median valley revealed the fact that the Atlantis-II-Deep is a potentially exploitable metalliferous mud in the economic sense. Sediments in the mineralized deep are composed mainly of oxides, various types of silicates and sulphides with considerable concentrations of zinc, copper, cadmium, silver and gold. The mineral-rich deposit, located at a mean water depth of about 2000 m, has an average thickness of 11 m, and is covered by a brine layer having a temperature of 60°C."

Jan 1, 1988

By Randolph R. Dreher, Michael L. Schreder

"In recent years, FFE Minerals has designed, installed and commissioned several large grinding mill circuits. This paper discusses the issues related to the erection and commissioning of large grinding mill circuits. The three circuits discussed are Collahuasi in Chile, Minera Los Pelambres in Chile, and Century Zinc in Australia. These circuits include large SAG and ball mills with both gear and gearless drive arrangements, as well as, both trunnion and shell supported mills. Aspects of these features are discussed with respect to their impact on installation and commissioning. While the normal challenges of mill erection and start-up were experienced, there were also a few unexpected challenges encountered partly due to the large scale of the equipment. An overview of the equipment and design ratings of these circuits is also provided.COLLAHUASIOverviewThe Collahuasi mills were started-up in November of 1998. The site is located in the Andes Mountains at an elevation of 4300 meters. The grinding circuit includes two lines featuring one SAG mill and one ball mill for each line. The circuit features a recycle conveyor around the SAG mills with provision for adding a pebble crusher in the future. The design tonnage of the grinding plant is 60,000 MTPD with an ore BWI of 10.5 kWh/MT.The SAG mills are 32’ x 15’ (1 3’ EGL) with 10,800 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The mills are driven by low speed synchronous motors with CCV variable speed drives. The SAG mills are trunnion supported and use hydrostatic lubrication. Feed to the SAG mills is via a rock-box type feed chute on a cart. The mills discharge on to trommel screens with a bucket wheel to remove the oversize.The ball mills are 22’ x 36.5’ (36’ EGL) with 12,500 HP drives. The drive arrangements are dual pinion through pneumatic clutches. The fixed speed mills are driven by low speed synchronous motors with GE Quadramatic load sharing drives. The ball mills are shell-supported and feature multi-pad bearings with hydrodynamic lubrication. The mills are fed via a rubber lined sump box with feed spout on a cart. The ball mills also discharge on to trommel screens. Twenty-six inch (26”) diameter hydrocyclones are in closed circuit with the ball mills."

Jan 1, 2001

By Claude Deveau

"With ever decreasing feed grades, finer mineralogy and increased demand for product, it became obvious that a major step in equipment performance was required to reduce operating costs and increase production. Offsite testwork indicated that a Centrifugal separator was capable of recovering fine tantalum and that the newly developed C Series Falcon concentrator would be capable of replacing many pieces of aging equipment and provide improved performance. Further investigation led to the rental and the purchase of a Falcon C20 concentrator followed by a C10 to maximize circuit performance.Falcon Concentrators Inc’ s practice of working with the customer mirrors Tantalum Mining Corporation of Canada’s (Tanco) philosophy of continuous product development. This synergy honed valve design for continuous operation in a highly abrasive ore environment.Tanco has recently purchased two more Falcon concentrators for the recovery of additional tantalum from its spodumene circuit. These new units have additional user friendly operating features partially based on developments made at Tanco.The Falcon C Series units have enabled Tanco to maximize recovery of tantalum that was otherwise lost while using the original conventional gravity circuit."

Jan 1, 2000

By J. H. Archibald

"IntroductionShot-saws are used for sawing rock throughout the dimension stone industry especially in granite quarry mills. Shot-saws, as currently designed, have an inherent wear problem which leads to slow cutting rates and repetitive blade changes which consumes much time. Because the saw blades are made from steel the abrasive shot used with them is limited to a certain hardness which effects the over-all efficiency of the sawing operation. Suggestions are made toward optimization of blade design and the sawing process. Blade DesignA common steel blade design is shown in Figure I. Note the perforations in the blade. These perforations or holes in the blade serve two or three purposes. The most obvious reason is to allow the abrasive shot a pocket in which to collect at the bottom of the blade, so that it can be distributed from these pockets into the cutting zone underneath the blade. The abrasive is fed to the saw in a slurry and usually comes in from the top. The blade must then cut a kerf wider than itself in order that the abrasive grains have a path leading from the top of the blade, down along its sides, and finally reaching the pockets and cutting zones. This circuitous path followed by the abrasive leads to side wear on the blades and high friction which can lead to blade buckling in severe cases. However, the fluidized path of the abrasives down the sides of the blade serves another purpose which is a positive gain if conditions are properly controlled. The abrasive slurry interacts with the perforations of the blade, the blade itself and the rock. This gap and the perforations in the blade, which are fluid filled, are sites of constant shearing motion. Eddy currents form in these gaps and pockets which tend to stabilize the blade by setting up balanced hydrodynamic forces which otherwise might not form in a non-perforated blade. A stable blade produces a more uniform cut in the rock. The third and final reason for the perforations are to allow the blade to wear in such a fashion that new pockets are always being formed and, consequently, new cutting surfaces between these pockets are also formed."

Jan 1, 1993

By M. C. Harris

The past twenty to thirty years have seen unprecedented research activity aimed at understanding the performance of flotation froths. In 1990, Finch and Dobby coined the term froth recovery factor, Rr, to represent the efficiency of the froth in delivering particles from the pulp-froth interface to the concentrate. Originally defined for flotation columns, Rr has also been found useful in modeling mechanical flotation cells, and a number of techniques, based on quite different approaches, have been developed for measuring the froth recovery in industrial flotation cells. None of these techniques is universally successful. This paper reviews the concept of the froth recovery factor, and the basis of each of the techniques that have been proposed to measure Rr, and examines the reasons for this parameter being so difficult to pin down. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists of CIM Sudbury, Ontario, Canada Edited by

Jan 1, 2009

By Arthur Notman

Since addressing the Institute a year ago on The Future of the Copper Industry (l), many things have happened, most of them bad. It has been a hard year for profits and prophets. It was, therefore, with consider-able perturbation that I accepted the gracious invitation of your Committee to reappear. On reviewing my remarks of a year ago, I. have wondered whether, under pressure of more important matters, the Committee had neglected to make a note of them, or whether they felt that further explanations from me were in order. In either event, I am glad that I am here and welcome the opportunity to make any contribution I can to a clearer understanding of the problems of copper to those concerned. The English-speaking nations own 80 per cent of the present world-production of the metal. Col. P. E. Barbour, Secretary of the Mining and Metallurgical Society of America, and I recently completed an estimate of the known world resources of copper. We placed the figure, in round numbers, at 100,000,000 tons of metal. Of this amount, about one-third lies in the United States, one-third in the British Empire, and one-third in South America; and all but 4 per cent of this is owned by British Empire and United States capital. Our figures do not include any estimates for Russia, Japan, or Europe, on which there are no available data. It is true, consequently, that the British Empire and the United States are the ones concerned. It seems to me to be a matter of great importance to the world at large, and of even greater importance to those nations themselves, that the known sources of supply of this metal, so essential both in peace and war, rest so strongly in their hands. I cannot believe that in the long run they will neglect their responsibilities in the wise administration of these resources.

Jan 1, 1932

By E. O. Abrokwah

Directionally solidified (DS) Rene 80 Superalloy was tested in thermo-mechanical fatigue (TMF) over the temperature range 500-900°C and plastic strain levels from 0.2 to 0.8% using a DSI Gleeble thermal simulator. Thermo-mechanical testing was carried out on the parent material in the conventional solution treated and aged condition (STA), as well as gas tungsten arc welded with an IN-738 filler, followed by solution treatment and ageing. Comparison of the base TMF unwelded alloy with that of the welded and heat treated alloy showed that varying crack initiation mechanisms, notably oxidation either by stress assisted grain boundary oxidation, or associated with grain boundary MC carbides fatigue crack propagation along grain boundaries and creep deformation were operating, leading to different "weakest link" failure initiation points.

Jan 1, 2011

By H. Ito, T. Takasu

Effects of a mechnochemical treatment to oxide Ni ores have been investigated to enhance the extractive ratio of Ni from them in acid leaching process. High intensity grinding by a planetary boll mill showed strong effect to enhance the extractive ratio of Ni, for example , 10% of extractive ratio of Ni in sulfuric acid leaching(0.05mo1/1,at room temperature) increased to more than 90% with 60min. of planetary boll milling. Effects of additives(sulfur and some oxidants) on the mechnochemical treatment have also studied. Sulfur showed almost no effect to enhance the total Ni extractive ratio but increases the selectivity of Ni extraction. More than a half of Ni could be extracted by water when Ni ore was grinded at addition of Na2S207 in the milling treatment. Some effects of mechnocemical treatments to Ni ore are summarized in this paper.

Jan 1, 2005

By R. Tessier, C. R. Larsen

"INTRODUCTIONOn November 10, 1982 Nor and a Inc signed an agreement with Golden Sceptre Resource Ltd. and Goliath Gold Mines Ltd. to construct a mine and milling facility.The Golden Giant mine is located in the Marathon area of north - western Ontario, immediately north of Highway 17 and about- 3.5 km west of Highway 614.With the exception of selected unit processes, the mill was designed for a nominal throughput of 2500 tonnes per day with early operating data to be used to identify sections requiring possible expansion to achieve an ultimate throughput of 3000 tonnes per day.Commissioning of the highly instrumented milling complex which includes crushing, grinding, cyanidation, and carbon in pulp processes commenced in February 1985. After water testing various sub-circuits from grinding through tailings, waste ore was introduced to ensure proper mechanical and electrical operation of process equipment.The first ore was milled as a mixture with waste on March 4, 1985. The first gold bullion was poured April 6, 1985.Initially, ore was only available from mine development at a rate of 700 t/d, which was milled at a minimum rate of 1200 t/d. While regular weekly shut downs of two to three days was useful for mechanical maintenance, changes, and modifications, process tuning was more difficult due to the non-steady operation. As increased quantities of ore became available, regular weekly shutdowns tapered off and process operation improved accordingly. For testing purposes and as ore was available, mill throughput was increased regularly to 2300 t/d and for very short periods of time to nearly 3000 t/d.No major design or operating problem has been encountered to date. The following is a brief description of the milling process and various operating highlights. Process flowsheets are shown in Figures 1 through 6."

Jan 1, 1986

"The McArthur River uranium deposit is the single richest uranium ore body developed in the world to date. The ore body’s average grade is 15% U3O8. Proven reserves are in excess of 450 million pounds. The grinding circuit is located underground. The ground ore is pumped to a surface facility where the slurry is thickened and loaded into containers for shipping to the Key Lake mill 78 kilometers to the south.The paper will briefly describe the mining method employed. The underground ore handling and grinding circuit, and surface facilities including slurry load out, wastewater treatment and the freeze plant will be described in detail. The paper will emphasize radiation and safety procedures that are followed to minimize operator exposure to radiation risks.LOCATIONThe McArthur River mine is located 78 kilometres north of the Key Lake mill. It is located at latitude 57’ N in northern Saskatchewan, within the southern boundary of the Athabasca formation. The nearest town is Pinehouse, located 320 kilometres to the south. Access to the mine is by an all weather road and by a private airstrip.HISTORYThe McArthur River Operation is jointly owned by Cameco Corporation (69.805%) and Cogema Resources Inc. (30.195%). Exploration for uranium in the McArthur River area started in 1980 by the Saskatchewan Mining Development Corporation, a predecessor company of Cameco.In 1984, a 12-kilometre long basement conductor was identified at a depth exceeding 500 metres. Systematic exploration drilling of this conductor resulted in the discovery of the P2 North deposit. Subsequent surface drilling programs from 1989 to 1992 delineated a narrow ore zone over a strike length of 1700 meters at a depth of 500 to 600 metres. At this time, geological reserves for the deposit were estimated to be 2.4 million tonnes at a grade of 5.0% U3O8 for a uranium content of 260 million pounds U308"

Jan 1, 2001

By N. H. J. Freire, D. Majuste

In this paper, the effects of some organic compounds on the current efficiency, cell voltage and specific energy consumption during nickel electrowinning, and on the deposit features (morphology, crystallographic orientation and nanohardness) were described. The organics tested here (extractant, diluent, flocculant, lubricating oil and acid mist suppressant) are currently used in industrial plants. The results indicated that only the flocculant and acid mist suppressant exhibit relevant negative impacts on the current efficiency and energy consumption. The current efficiency dropped from 93.6 % (organic-free solutions) to 86.0 % and to 92.8% in electrolytes containing 100 mg.L-1 of acid mist suppressant and flocculant, respectively. At this concentration, their addition to the electrolyte led to increases of the specific energy consumption in the order of 18 % (acid mist supressant) and 2 % (flocculant). Cyclic voltammetry showed that Ni nucleation occurs at more negative potentials at 50 and 100 mg.L-1 of these organics in the electrolyte, thus indicating an inhibition of the deposition process. The deposit quality decreased at the higher concentration of all organics, when more hydrogen pitting was observed. The acid mist suppressant caused delamination of the Ni deposit at 50 and 100 mg.L-1. The addition of 100 mg.L-1 of flocculant and acid mist suppressant to the electrolyte increased the nanohardness of the deposit around 31 and 72%, respectively. The increase in Ni deposit hardness may lead to a decrease in the material ductility, thereby affecting the stripping and cutting of Ni sheets. Our findings may be helpful since strong adverse effect of some organics that may be present in the electrolyte were identified, thus the industry can control and optimize the organic´s dosage in the corresponding operations.

Jan 1, 2016

By Pierre Roy, Claude Gosselin, Maryam Sadeghi, Michel Bourassa, Christian Rochefort, Claude Bazin, Gautier Mahieu, François Lavoie, Marilène Renaud, David Cataford

"Spirals are gravity concentrators used for the concentration of iron oxide minerals from ores. This paper presents the mineral size recovery curves observed for spirals operating in two Canadian iron ore processing plants. The size recovery curves are presented for rougher, cleaner and re-cleaner spirals. The partition curves observed for the spirals are significantly different than those observed for typical gravity concentration devices such as hydrocyclones or hydraulic classifiers. The size recovery curves show the complex behaviour of the minerals as they flow down a spiral and are analysed with a view toward process modelling and simulation. Initial simulation results show that gains in the iron recovery can be achieved by increasing the recovery of coarse iron oxide particles in the rougher spirals.INTRODUCTION Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and different heavy minerals ores (Wills, 1992). The classification of the particles in spirals is based on the combination of gravity, centrifuge, drag, lift and Bagnold forces (Atasoy and Spottiswood, 1995; Burt, 1984; Bouchard, 2001). Several papers are dedicated to the analysis of the forces acting on the particles flowing down a spiral (Das and al., 2007; Sivamohan and Forssberg, 1985; Holland-Batt and Holtham, 1991; Holtham , 1992). Most of these papers aim at the development of a general model for the simulation of the classification of the particles for coal ore processing. Few papers deal with the operation of spirals for processing iron ores (Hyma and Meech, 1989; Srivastava, 2001; Dallaire et al., 1978) and fewer papers present results for spirals used as cleaners following a rougher stage. Since the classification in spiral classifiers is dependent on the particle size and specific gravity a partition or performance curve commonly applied to classifiers (Mai Manga et al., 2012) is used here to analyse spiral operation. Few papers were found to describe the operation of spirals in terms of partition curves (Atasoy and Spottiswood, 1995; Holland-Batt and Holtham, 1991; Richards et al., 2000). Most of the investigations presented the application of a model to simulate the position of coal particles of various sizes and specific gravities along the trough of a spiral (Kapur et al., 1996; Holland-Batt and Holtham, 1991). In addition most of the available literature on spirals deals with one stage of concentration by spirals (Dallaire et al., 1978; Das and al., 2007; Sivamohan and Forssberg, 1985) while industrial circuits usually consist of rougher and cleaner spirals."

Jan 1, 2014

By Michael Cooper, Eric Konigsmann, A. Moerman

"A paste backfill plant and underground piping distribution system was commissioned at the Brunswick Mine in June, 1998. Concentrator tailings, composed mainly of pyrite and lesser amounts of silicate minerals with a P80 of 37um (45 YO-20 pm), are pumped to the backfill plant. The backfill plant uses conventional thickening and disc filtering to dewater the solids, which are then mixed with binder in twin screw mixers. The paste is discharged through a gob hopper and one of three boreholes by gravity. Approximately 65% of the concentrator tailings will be placed underground at full production. The remaining thickened tailings will be pumped to an existing impoundment area. Application of paste technology will completely replace the use of cemented rock fill in the mine by the end of 1998.The design capacity of the paste backfill plant is a total of 360 dmtph of cemented paste through two parallel production lines. The plant is highly instrumented and controlled via a hybrid Programmable Logic Controller (PLC-5) and Fisher ProVox Distributed Control System that is in communication with the property information highway. Video and audio signals from the underground system are carried to the surface plant via a leaky feeder communications/fiber optic system.The underground distribution system consists of a network of 200mm diameter boreholes and piping. There are approximately 3.5km of boreholes and 5.5km of piping in the system. To minimize pressures, the greatest piping length from any borehole is approximately 400m with all piping being open-ended. There are no valves in the entire paste distribution system.Construction of the plant, including installation of piping to and from the plant and preparation of the underground distribution system, was completed in less than one year from the time of management approval for the $M 22.3 project."

Jan 1, 1999

By J. D. T. Steyl, C. A. Biley

"The chemistry of electrolyte systems containing iron remains generally poorly understood despite their prevalence in many natural and industrial processes, particularly in hydrometallurgy. These systems are typically challenging to study and model due to their affinity for complex formation and precipitation even at low pH. Recent developments in the hydrometallurgical processing of nickel laterites at Anglo American have called for a deeper understanding of the fundamental chemistry of the Fe2(SO4)3–FeSO4–H2SO4–H2O system. This paper details the development of an internally consistent, Pitzer ion-interaction model of this system, with explicit recognition of important contact ion pairs (CIPs). The primary application of this model is a thermodynamic framework for the interpretation of kinetic processes occurring during iron(III) reduction with SO2. Adopting a rigorous thermodynamic basis for the system chemistry facilitates the formulation of simple rate expressions that are capable of inherently capturing complex effects. While the iron(III) reduction case study remains the focus of this work, the developments have more universal applications and the thermodynamic speciation model can be extended into other systems containing acidic ferric sulfate.INTRODUCTIONIron is present in nearly all hydrometallurgical refining circuits typically as both a necessary and unwanted impurity and needs to be removed and disposed in a safe and efficient manner. This is generally performed by precipitation to form a range of solids such as hematite, goethite or jarosite. Numerous studies in the open literature have focussed on the removal of iron from refractory gold sulfide ore (Berezowsky & Weir, 1989; Berezowsky et al., 1991) and zinc pressure leaching (Buban, 1999; Ismael, 2003), and PGM matte sulfide circuits (Dutrizac & Monhemius, 1986). Moreover, since ferric iron is a strong oxidizing agent, it has been used extensively as a leaching agent for sulfide minerals (Dreisinger, 2006). Given the outlook of challenging economic conditions, declining ore grades and increasing levels of impurities, effective iron management is going to become increasingly critical to all hydrometallurgical processes.Against this background, and considering the widespread importance of acidic iron sulfate systems throughout natural and industrial processes, it is unexpected that the knowledge of the fundamental solution chemistry of these systems contains such significant gaps, particularly at the conditions typically found in hydrometallurgical applications. Existing literature describing the measurement and modelling of solution speciation in these systems have highlighted their significant chemical complexity (Magini & Caminiti, 1977; Magini, 1979; Lee & Tavlarides, 1985; Stipp, 1990; Papangelakis et al., 1994; Gil et al., 1995; Majzlan & Myneni, 2005; Kormanyos et al., 2008; Yue et al., 2014). Partially responsible for the lack of quantitative speciation measurements is the strong tendency of ferric to hydrolyse at even low pH (Flynn, 1984), complicating the laboratory study of such systems. Moreover, the large number of aqueous species that may co-exist simultaneously makes the study of individual species and the modelling of the numerous interactions between these species extremely difficult (Dry & Bryson, 1988; Stipp, 1990; Majzlan & Myeni, 2005; Kobylin et al., 2007)."

Jan 1, 2016

By B. Goard

"IntroductionCemented backfill has been placed underground in slurry form in Inco Limited's Ontario Division mines since the early 196Os. The slurry was traditionally mixed on surface at between 65 and 70 wt% solids* and transported underground via gravity through a borehole-pipeline distribution system. This method of placement, while simple and dependable, has proven to be costly because of the large amounts of transport water involved.A significant quantity of the slimes buildup on mine levels is caused by the backfill water carrying cement and other fine material out of the stopes. The level cleanup and eventual pumping or hoisting of the slimes and water back to surface result in substantial indirect backfilling costs.The cement that remains in the stope is always overhydrated because of the high water cement ratios that exist. As a consequence, high concentrations of Portland cement must be added to the backfill to produce the fill strengths required for the different mining methods.Pouring backfill at these densities also demands extensive fill preparatory work in the stopes to withstand the hydraulic heads created by the slurried fill. This, along with the delays in pouring necessary to allow for water drainage, result in significant losses in productivity.These negative aspects of slurry placed fill has led Inco Limited to investigate several methods of transporting backfill underground via pipeline, at higher densities (i.e. 75 to 95 wt.% solids). Three separate transport methods are presently being experimented with by the Company's Mines Research Department. Each utilizes a different technique or form of flow transport, i.e. concrete pumping technology, high density slurry flow, and pneumatic conveying."

Jan 1, 1987

By John Hoffert, Darren Colwell, Greg Tucker, Jeremy Kinch, Greg Rasmussen

"The Kemess Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines. On February 11, 2000 Northgate Exploration Limited acquired Kemess Mine from receivership. Since acquisition in 2000 Kemess has seen many accomplishments, including the reduction of costs by 40%.One of the largest site capital costs was the construction of the tailings storage facility dam, which when finished will be one of the largest earth filled dam structures of its type. The existing construction design by AMEC called for a kilometer wide rock dam to be built from the 1350 M elevation to the 1504 M elevation at a 5.5:1 slope by hauling over 30 million tonnes of non-acid generating waste rock 7-kilometers from the open pit to the tailings dam, which was highly expensive.Kemess realized an opportunity for cost reduction was possible if the dam could be built from suitable quality tailings sand; however the sand did not meet the neutralizing potential ratio specifications. It was determined that cycloning combined with flotation to reduce pyrite concentration in the sand would produce a non-acid generating product for dam construction. The sand plant design challenges were to remove the sulphides from the tailings to obtain an NPR greater than 2:1 and provide a consistent sand product for the construction with a fines content of less than 15% passing 200 mesh. After a 2-year testing design and construction period, the sand plant was successfully started at the end 2002 resulting in higher than expected sand quality and production rates.This paper describes the plant design phase, commissioning, and operation of the tailings sand plant for construction of the tailing storage facility dam to enable us to meet all the engineering and regulatory requirements. The many challenges faced were successfully met using several innovative designs. The operational, economic, and environmental benefits are detailed."

Jan 1, 2004

By H. G. Rushton, A. S. Romaniuk

"The opening chapter of this volume, by A. Ignatieff, places in perspective Canada's coal resource base as part of the world scene. This chapter will focus on the Canadian scene.Units of measurement in this report are in the International System of Units (SI) as approved for official use by the Canadian Standards Association and Metric Commission Canada. These units have been adopted by the Mining Association of Canada and the Coal Association of Canada. To assist with the shift to metric units these two associations have published ""Metric Practice Guide for the Canadian Mining and Metallurgical Industries"", 1978(1J, Appendix ""A"" lists some useful conversion factors along with SI prefixes. The last official assessment of Canada's coal resources and reserves was done by the Department of Energy, Mines and Resources and presented in Report ER 79-9 ""Coal Resources and Reserves of Canada"", published in December 1979 and authored by H.U. Bielenstein, L.P. Chrismas, B.A. Latour and T.E. Tibbetts(2). The Geological Survey of Canada has a continuing project concerned with coal resource assessment as does CANMET, whose concern is with coal reserve assessment and coal quality. As well, Alberta's Energy Resources Conservation Board (ERCB) has a continuing assessment program for coal in Alberta and publishes an annual reserves report, the current issue of which is cited as reference No. (3). The difference in resource and reserve terminology as used by EMR and ERCB has a major effect on derived tonnages for Alberta. This difference will be discussed later. In 1982 the Department of Energy, Mines and Resources produced a map titled ""Canada-Coal""<4J which outlines coalfields and illustrates coal import and export movements for the years 1981and1980. A copy of this map is contained in the map pocket of this publication. Two other resource assessment reports are noteworthy, the first is ""Coal Resources of Southern Saskatchewan: A Model for Evaluation Methodology"", by J.A. Irvine, S.H. Whitaker and P.L. Broughton<SJ which is one of the major outputs of a joint federal-government study of southern Saskatchewan's lignite deposits. (Another output from this same study' is the Geological Survey of Canada's SASCO file, a computer processable file holding borehole and coal quality data.) The second is ""Deep Coal Resources of the Interior Plains, Estimated from Petroleum Borehole Data"", by G.D. Williams and M.C. Murphy(6) which identifies coal resources from nearly 4,000 petroleum exploration boreholes distributed uniformly over an area spanning Manitoba, Saskatchewan, Alberta and British Columbia."

Jan 1, 1985

By Julian Wills

The Candrill was developed with Soredem as a one-operator rockdrill for Canadian narrow vein mining. It provides the benefits of increased drilling rates, lower noise and vibration, mass reduction of 20% and system cost saving. The Candrill is to be commercialised at the end of 2001 together with a stoper drill through Parts Headquarters, Novatek&apos;s Canadian agent. The Candrill or pneumatic drills may be further exploited using a simple mechanised drilling system to further reduce operator labour, improve drilling speeds by up to 50% and to enhance drilling accuracy. Novatek&apos;s drilling system for simple mechanisation in gold and platinum mines is integrated with roof supports, can operate in stope widths as low as 800 mm and has resulted in labour savings of 50%, improved advances per blast of 20 to 50% and improved operator safety and ergonomics.

Oct 1, 2001

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005