Search Documents

By T. L. Tanton

Introduction Sturgeon River area, on the east side of lake Nipigon, Ontario, was the scene of a gold rush in 1934. According to press reports, the active staking during the latter part of the summer spread out rapidly from the early holdings until it embraced practically all of the lower basin of Sturgeon river in a belt up to ten miles wide extending west from Kinghorn for 35 miles to lake Nipigon. And, before winter set in, active prospecting and claim staking reached beyond lake Nipigon to areas where belts of ancient schists were known, notably west of Obonga lake. The writer's familiarity in past years with the areas to which attention has been directed admits of some observations on means of access in the field, the general geology, and the progress that has been made in identifying formations favourable for the occurrence of gold. Canoe Routes From the writer's observations in Sturgeon River area in 1917 and in the Obonga Lake area in 1933, it is recalled that there is, locally, a striking dif~ ference in the accessibility of the two areas by travel along canoe routes. Sturgeon River area is easily accessible from Kinghorn or Jellicoe stations on the Canadian National railways. Many small lakes, commonly of the linear type and with elongations east and west, occur among the forested rocky ridges near Jellicoe (Figure 1) and to the east and west along, or adjacent to, Sturgeon river. This stream has long stretches with gentle current between the falls and rapids. The drainage system provides excellent canoe routes (Figure 2), and the interruptions to travel (Figure 3) are remembered .as scenic features that were passed by portages with firm footing. West of Obonga lake, the streams flowing easterly to lake Nipigon may be followed through scenic canyons to a plateau of law relief characterized by extensive muskegs and shallow, brown-water lakes; and along small streams, where beaver dams have been destroyed, there are muck ponds where the usual alternatives of paddling or portaging can be dismissed in favour of the 'moosing' method of progress with the canoe (Figure 4).

Jan 1, 1935

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014

By Jochen Petersen, Caroline Muzawazi

The technical feasibility of ammonia leaching of PGM bearing Platreef flotation concentrates was investigated as an alternative method for the recovery of base metals prior to precious metal recovery. The composition of the concentrates includes 2.02% Cu and 3.17% Ni, and the major base metal minerals are chalcopyrite and pentlandite. Optimal leaching conditions were initially established in shake flask experiments to be a solution containing 4 M NH4OH, 4 M (NH4)2CO3 and a pH range between 9 and 10. These were used as base case conditions in column and batch stirred tank reactor tests, where the effects of total ammonia concentration and operating temperature were explored further. At optimal conditions nearly 100% Cu and Ni extraction were obtained in the batch stirred tank reactor, and 95% Cu and 60% Ni extraction was obtained in columns. The activation energy for chalcopyrite and pentlandite was 36 kJ/mol and 16 kJ/mol, respectively, in both reactors, indicating different reaction pathways for the two minerals. Gas-liquid mass transfer appears to be the limiting reaction step in columns much more than in tanks, and the degree of ammonia loss to air is significant. This initial test work indicates the feasibility of using ammonia leaching for this and similar materials as an alternative route to conventional smelting and refining prior to PGM recovery, but a number of technical challenges still need to be overcome.

Jan 1, 2014

By Tassos Grammatikopoulos

The St. Lawrence deposit is a large wollastonite skarn (ca. 9 Mt @ 41.3% wollastonite) adjoining the gabbroic-to-syenitic Leo Lake pluton in the granulite facies of the Frontenac Terrane of the Grenvillian Central Metasedimentary Belt. It occurs within a horseshoe-shaped horizon of quartzite, open to the east. The skarn extends over 1.2 km2, and comprises wollastonite-dominant, wollastonite-clinopyroxene, and diverse quartz-feldspar-sulphide (-titanite) layers, interbanded with, and strongly folded within, the quartzite. As in the world-class wollastonite deposits of the Willsboro district, New York State, no carbonate protolith is preserved and calcite is a negligible constituent of the mineralized zones. Wollastonite development is nonetheless ascribed to metasomatism of a metacarbonate unit by magmatogene, silica-rich, CO2-poor (XCO2 < 0.05) fluids, at P = 350 MPa and ca. 560 oC, or, alternatively, 550 MPa and ca. 630 oC. Several high grade zones, averaging >40%, but locally exceeding 80%, of translucent, white, tabular wollastonite grains, with lengths of 0.2 - 2 cm, have been delimited by drilling. Preliminary beneficiation studies yield high aspect-ratio and high-purity (low Fe and Mn) concentrates. St. Lawrence compares favourably to other known prospects and operating wollastonite deposits; having good chemical and physical properties, low iron content, and high aspect ratios (>20:1). In addition, the deposit has a favourable size and location, and will benefit from a low Canadian dollar. Canada currently has no wollastonite production.

May 1, 2002

By A. J. Antony Chettupuzha

During a construction project, it is important to ensure that accurate and pertinent knowledge is delivered on time to appropriate personnel. The criticality of documents exchanged or referred to by various parties, evolves over the course of the project lifecycle. Determining the criticality of documents at different stages of the project can aid companies with managing the flow of information in an organized manner, while providing for the detection of potentially disruptive, erroneous material that could result in delays and costs. Therefore, it is crucial to determine documents which have the potential to disrupt a process (by virtue of being incorrect versions etc.) so that they may be isolated or prevented from entering or interfering with the active flow of information in a project, while also ensuring standard revisions of documents are recognized and accessed accordingly. Electronic Product and Process Management [EPPM] systems provide the capability to establish and map information flow between different parties in a construction project. Analyzing an EPPM system may yield information about the criticality of certain documents within an activity, as well as isolate characteristics peculiar to documents which can assist in risk mitigation. We propose methodology that identifies such critical documents.

Aug 1, 2013

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By Xiang Yu

Hong Kong has a dense distribution of utility services laid under its road network. Utility undertakers frequently demand road openings to install new services and/or maintain existing ones. Road openings can cause troubles to the road network and negatively impact the public interest. Highways Department is responsible for managing road openings in Hong Kong under the Land (Miscellaneous Provisions) Ordinance. Highways Department has spent a lot of efforts to computerize excavation permit processing and utility management. The computerized system has gone through several generations and the current one is called the excavation permit management system (XPMS). On the one hand, the XPMS handles various excavation permit processing functions including permit application/approval/refusal/issuance/extension/termination, fees/costs, permit conditions, and permit period assessment; on the other hand, the XPMS accounts for some important utility management issues such as spatial check, coordination of multiple openings, traffic management, audit inspection, and defect liability. This paper discusses how the application, coordination, and other administrations of an excavation permit are eased by using the XPMS in Hong Kong. Background information such as the governing legal and regulatory framework, and Highways Department?s administrative structure is introduced. The system architecture and advantages of the XPMS are presented. The work procedures and various functions of the XPMS are studied in detail.

Aug 1, 2013

By Z. Trojanová

Mg micropowders generated by gas atomisation of a magnesium melt with argon were mixed and ball milled with ceramic nanoparticles prepared by laser-induced gas phase reaction. The materials were then hot extruded. Specimens were deformed in tensile as well as compression tests at temperatures between 20 and 300 °C at a constant initial strain rate. The flow stress is significantly influenced by the test temperature. The yield stress decreases with temperature. This decrease and the flat character of the stressstrain curves at elevated temperatures indicate possible contributions of softening processes. The materials studied exhibit high-damping characteristics. The results are analysed and possible mechanisms are discussed.

Jan 1, 2006

By P. Leo

The hot deformation behavior of a Mg-9A1-1Zn alloy produced by high pressure die casting has been investigated by means of compression tests in the temperature and strain rate ranges of 125-300°C and 10-5-10-1 s-1 and torsion tests over 150-450°C and 5, 0.5, 0.05 5-1 . The compression samples were deformed in the die-cast state or after homogenization at 415°C for 2 h to evaluate improvements. A premature fracture at 45° with respect to the compression axis was observed in samples strained at low temperatures and high strain rates. The torsion specimens were tested as received or after a predeformation-homogenization treatment. In addition to constitutive analyses suitable for modeling previously published, the results are fitted to a relationship between strain rate normalized by diffusion coefficient and flow stress normalized by modulus. The results fit well with a set of published creep experiments that were conducted in the range of 70-150°C.

Jan 1, 2006

By S. E. Malouf, R. Hinse

"The Mineral possibilities of the Chibougamau area were first recognized by Richardson in 1870 and Low in 1885, both of the Geological Survey of Canada. The first record of interest by the Quebec Bureau of Mines is in 1904, when J. Obalski reported on the discovery of copper and asbestos by Peter McKenzie in the previous year. Reports of 1906 and 1907 covered the McKenzie Gold Mine find and other deposits. In 1908 Prof. Dulieux described the quartz vein on Merrill Island and the mineralized zone on the near-by mainland. In 1910 the Chibougamau Railway Commission, though commenting favourably on the possibilities of the area, concluded that a railway was not then warranted.In spite of this, prospecting in the district continued. The main Campbell Chibougamau deposit, the Blake showing on Merrill Island in Dore Lake, was found in 1920, and other discoveries were made soon after. Between 1927 the work of Mawdsley, Retty, and Norman tor the Geological Survey and the Quebec Bureau of Mines stimulated further interest. In 1934 Consolidated Chibougamau Goldfields Ltd., a subsidiary of Consolidated Mining and Smelting Co. of Canada Ltd., acquired the Merrill Island and Cedar Bay holdings of Chibougamau Prospectors Ltd. They embarked on an aggressive campaign, directed essentially at the gold quartz veins at Cedar Bay. Exploration there included a 522-foot shaft, 4,732 feet of drifts and crosscuts, and about 34,000 feet of surface and underground diamond drilling. Thirteen holes were also drilled on the replacement sulphide lens at Merrill Island. Operations were suspended in 1936, as the occurrence was too low grade for development at the existing metal prices and under difficult operating conditions.The completion of the Quebec Bureau of Mines highway from St. Felicien to Chibougamau in 1950 was followed by a project of detailed geological mapping by the Bureau. It also encouraged Campbell Chibou-gamau Mines to acquire the assets of Consolidated Chibougamau Gold-fields and commence a program of surface exploration. Between August 1950 and April 1951, 41,183 feet of diamond drilling was done on the Cedar Bay and Merrill Island holdings. The Blake showing off the west shore of Merrill Island developed at depth into a major orebody. A lease was obtained on adjacent ground from Merrill Island Corporation, and underground work commenced in November 1951. Development at Merrill Island to June 1st, 1955, included a four-compartment shaft to 1,225 feet, with 8 levels at 150-foot intervals, 5,317 feet of raises, 16,709 feet of drifts and crosscuts, 52,514 feet of surface and 96,593 feet of underground diamond drilling."

Jan 1, 1949

By A. Warczok

The computer simulator of slag cleaning in an electric furnace is based on a set of mathematical models describing heat liberation, the rate of slag reduction and gravitational coalescence of matte and metallic copper inclusions. The simulator consists of a mass and heat balances as a frame, in which the kinetic equations of the slag reduction and phase separation are incorporated. Friendly user-screen interface allows for dynamic control of process parameters in real time together with simulation of typical operations, such as furnace charging with liquid slag, solid reverts and coke, tapping out of the slag and matte, motion of electrodes and control of the transformer. The batch, semi-continuous or continuous process can be simulated. The process parameters are displayed and continuously recorded for further analysis. The computer simulator is a powerful tool for process optimization, training of furnace operators and the design of new slag cleaning installations.

Jan 1, 2007

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By Northeastern University, B. Y. Cui, B. Y. Wang, D. Z. Wei, W. G. Liu, Z. C. Guan, S. L. Gao

To recover iron values from low grade ores by reverse froth flotation method, further research on cationic collectors used in reverse flotation of iron ores is launched to promote the utilization efficiency of iron ores. In this paper, one new cationic surfactant, bis(2-hydroxylethyl) dodecylamine (BHD), that could be dissolved in water easily was used as collector for quartz flotation. Flotation results indicated that BHD shows stronger collecting performance on quartz than hematite. The maximum recovery of 96.30% to quartz is obtained at a collector concentration of 20.0 mg/L in the pulp pH range from 5 to 7. This collector can be used to float quartz from hematite. And optimal separation results with 86.59% iron recovery and 66.60% iron grade to synthetic sample were achieved at a collector concentration of 20.0 mg/L and pulp pH of 5.02 when hematite and quartz were mixed at a mass ratio of 3:2. The adsorption mechanism of the collector on quartz surface was investigated by XPS analysis, infrared spectroscopic analysis and zeta-potential measurements, which revealed that electrostatic attraction and hydrogen bonding adsorption occur between collector and quartz surface.

Jan 1, 2016

By J. F. Wright

Introduction Previous to 1924 the mining fields of Manitoba and adjoining territory had not been prospected in detail, and the reports of the exploration of the mineral discoveries to that date had been discouraging. As a result of the apparent failure of all the mining operations, some considered that geological conditions in the country westward from lake Superior extending across western Ontario, eastern and northern Manitoba, and northern Saskatchewan, were different from those in the northeastern part of Ontario, where large gold mines had been developed. Discoveries of importance thus were necessary to renew interest in the mining possibilities of this part of the Canadian Shield, and the successful operations at Flin Flon and Howey in large part were responsible for the beginning of the present activity in what may be described as the part of the pre-Cambrian Shield within central Canada. In Manitoba, the more important developments at present are in the Central Manitoba, Gods Lake, and Knee Lake fields. The large area from west of Flin Flon east to Herb Lake, also, is being explored carefully for gold deposits of merit. A number of properties in Red Lake, Woman Lake, and Pickle Crow areas are being drilled and explored underground. Many of the mines of the Lake of the Woods area, that were producing gold 30 years ago, are re-opened, and new prospects in this field and in the country to the east are being explored. The recent development of Little Long Lac mine in an area near the railway, and considered by some to have been thoroughly prospected years ago, has stimulated interest in the areas formerly prospected. In the autumn of 1934, the belts of greenstone and sediments in the country east of lake Nipigon were staked, and deposits in these fields will be explored in detail this year. This paper is presented to discuss the general features of the geology and gold deposits of the various prospecting fields in Manitoba and adjoining territory. Details of a number of the areas and mines will be presented at this meeting in papers by Barton on Little Long Lac, Tanton on Sturgeon River, Baker on Gods Lake, and Brownell and Kinkel on Flin Flon. Although mining was not active in most of this territory previous to 1930, geologists of the various government departments continued field studies and interesting reports were issued.

Jan 1, 1935

By D. K. Sarkar, J. Perron, J. D. Brassard

"Nearly perfect spherical shaped water drops rolling-off from the surface of lotus leaf is one of the beauties of nature. This kind of surface is called superhydrophobic, since the water does not like it. Physically, a superhydrophobic surface provides a contact angle (CA) of water over 150°. The combinations of both mico-nanostructure topography as well as low surface energy are essential to have such high CA on a surface. Nano-micro structured superhydrophobic surfaces have been developed in different methods. (i) Monodispersed fluorinated silica nanoparticles have been synthetized via Stöber Sol-Gel process and deposited on various surfaces, such as aluminium or glass, to obtain transparent superhydrophobic thin films. (ii) Similarly, zinc stearate nanocomposite coating has been fabricated by spray process on the same substrates. These thin films are found mechanically robust with drag reduction of coefficient 16% lower than as-received surfaces. (iii) By electrodepositing pure zinc on steel surfaces and further coating it with diluted room-temperature vulcanized silicone rubber, the surface become superhydrophobic. This superhydrophobic surface protects the steel against corrosion by increasing the polarization resistance from 1.5 k? on steel to 44.4 k?. This coating also reduced the ice adhesion on the steel surface 6.3 times as compared to bare steel substrates. Globally, these superhydrophobic surfaces have tremendous applications against corrosion reductions, drag reductions and ice adhesion reductions.INTRODUCTIONSuperhydrophobic coatings are increasingly attractive to the industry and academia due to their unique self-cleaning properties as a result of their water repelling characteristics. Fabrication of superhydrophobic coating is an inspiration from nature as water is seen to repel on many natural surfaces such as those of the lotus leaves, butterfly wings, water striders’ legs, and so on (Gao & Jiang, 2004; J. Huang, Wang & Wang, 2006; Neinhuis & Barthlott, 1997; Zheng, Gao & Jiang, 2007). This non-wetting phenomenon is well understood on lotus leaves, shown on the Figure 1 (a), and it is considered as the basis of the studies of superhydrophobicity. The existence of this binary structure on the surface of the lotus leaves allows a large amount of air entrapment and consequently reduces the contact area of water on it and the presence of low surface energy waxy components with reduced affinity to water together leads to the superhydrophobic properties. The phenomenon is shown on Figure 1 (b). Cassie and Baxter (Cassie & Baxter, 1944) as well as Wenzel (Wenzel, 1936) proposed two mathematical models to explain the wetting phenomena on rough surfaces that leads to superhydrophobic properties. By definition, superhydrophobic surfaces are characterized by a water contact angle value = 150° with the rolling off of water drops from the surfaces (Sarkar & Saleema, 2010). Superhydrophobic surfaces find tremendous importance in the technological world where it can applied in domains such as anti-corrosion, anti-biofouling, electrowetting, icephobic and even in drag reductions (Bushnell & Moore, 1991; Cao, Jones, Sikka, Wu & Gao, 2009; Carlborg & van der Wijngaart, 2010; Carré & Mittal, 2009; Y. Huang, Sarkar & Chen, 2010a; R. Karmouch, Coude, Abel & Ross, 2009). However, the most important challenge faced by industries is their feasibility large scale in an effective an economical manner."

Jan 1, 2016

By P. E. Cavanagh

"The Davis tube test has been used for many years as a laboratory method for determining the magnetic iron re-coverable from a magnetite iron orebody. This paper de-scribes a method for determining the recoverable iron from ores of the Labrador Trough type, with the usua1 flow sheet utilizing spirals followed by magnetic separation.The mechanical structure of a metamorphosed iron ore, resulting from recrystallization over long periods of time, is the basis for the laboratory method developed. Similarities between the structures of such recrystallized ores and the structure of annealed and recrystallized steel are noted.A laboratory technique to determine the size of the different grains of gangue and iron ore minerals is de-scribed and the application of this information to arrive at recommended grinding techniques and flow sheets is demonstrated. The use of the method to determine recoverable iron in such ores is compared to actual iron recovery in the pilot-plant and commercial concentrations of the same ore.The use of a specified lower limit of recoverable iron as determined by this method, in order to design open-pit limits, achieves practical results when compared to designing a pit based on an arbitrary lower limit of total soluble iron. The Ungava Iron Ore deposits are used in giving an example of the resulting pit design changes."

Jan 1, 1968

By V. A. Leão, A. M. Silva, S. M. Bertolino, B. C. S. Ferreira, D. Guimarães

Although not considered a high risk pollutant as compared to toxic metals and acidity, environmental agencies worldwide are proposing regulations to control sulphate in effluents and drainages by setting a threshold value varying between 250 mg/L and 500 mg/L. The aim of this study was thus to compare four different techniques for removing sulphate ions from mining/metallurgy effluents. The first alternative studied was sulphate removal by precipitation as ettringite. Treating a synthetic solution containing 1650 mg/L sulphate at 22±1 ºC resulted in removals close to 85% during continuous precipitation. Sulphate sorption was also investigated using three different ion exchange resins as well as limestone. Fixed bed experiments produced sulphate loadings of up to 70 mg SO4 2-/L resin, at pH 2.0. In neutral wastewaters, limestone is also a potential adsorbent producing a maximum particle loading of 19 mg/g. Sulphate sorption on limestone seems to be an alternative to treating mine waters with sulphate concentrations below the 1200-2000 mg/L range, where lime precipitation is not effective. Subsequently, sulphate removal by sulphate reducing bacteria was also investigated and it was observed that reactor’s hydrodynamic conditions and the choice of substrate are important factors for the process. The different technical aspects of each technology are addressed.

Jan 1, 2014

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By G. R. Parslow

U, Fe, Mn, Ni, Cu, Zn and Co data for the sediment in both Key and Seahorse lakes, which overlie portions of known economic uranium deposits in the region, are presented. With the exception of U, Fe and Mn, the elemental distributions can be considered anomalous, in a statistical sense, in both lakes. The U values are of particular interest in that Key Lake is not anomalous, whereas Seahorse Lake is markedly anomalous. Tentative correlations made with background data from other surveys in an attempt to differentiate between anomalous and background values indicate that deviations from linearity in a distribution, and not absolute mean or maximum values, are indicative of anomalous samples within the distribution.

Jan 1, 1979

By Nobuyoshi Yabuki

Building Information Modeling is a prevailing methodology in the building industry and half (by length) of the world&apos;s shield tunnels are in Japan. Accordingly, for shield tunnels from 2005 to 2007, we developed a product model called IFC-ShieldTunnel, which is based on Industry Foundation Classes (IFC), in order to meet the future demand for such a product model. IFC-ShieldTunnel was developed by adding new elements that are specific to shield tunnels and that are not included in the original IFC. The added elements include shafts, segments (A, B, and K types), waterproofing elements, segment joint elements, and ring joint elements. Furthermore, soil layers and void elements were created. Recently, we updated the product model by re-organizing the entities and correcting errors. We deployed the updated IFCShieldTunnel model in the construction of an actual shield tunnel in Tokyo for about a year from August 2010 in order to check its feasibility. In the verification process, first, segments were modeled using Autodesk Revit Structure 2011 and property data were assigned to each segment element. Next, a mapping between the original attributes of the entities of IFC and properties of IFC-ShieldTunnel segments was developed. Using this mapping and IFC?s IfcBuildingElementProxy function, we were able to convert the IFC data from Revit Structure 2011 to IFC-ShieldTunnel automatically. Segment data were also converted from Revit Structure to Google SketchUp by IFC-ShieldTunnel. Furthermore, the construction scheduling and cost data were converted from Revit Structure to EXCEL for 4D and 5D analyses of construction. We interviewed engineers who used IFC-ShieldTunnel and received positive comments about the utilization of the product model. Overall, our test demonstrated the feasibility of IFC-ShieldTunnel. In future work, we plan to apply IFC-ShieldTunnel to more projects and test its practicality.

Aug 1, 2013