Search Documents

By M. Gangal, M. Grenier, D. Mchaina, S. Hardcastle

"Exposure to airborne respirable silica in surface and underground mine operations is known to be the cause of industrial lung diseases. For this reason, silica is a regulated substance and worker exposure must be monitored regularly. Diesel exhaust also contains substances which are potential caricinogens. In an underground setting, diesel particulate may be the main component of what is referred to as respirable combustible dust (ReD). Although diesel particulate or soot is not at present a rigorously regulated substance, new epidemiological data is prompting North American institutes and agencies to regulate diesel soot or RCD exposure. This paper describes a method where by silicaand RCD exposure may be determined using a single personal sample. In this method, an airborne respirable dust sample is obtained and analyzed nondestructively for silica components using an on-filter X-ray diffraction method. Filters are then ashed at 500°C in a muffle furnace over a four-hour period to determine mass loss due to RCD burning. Using on-filter X-ray diffraction analysis as opposed to redeposition of dust samples onto another analytical substrate allows the"

Jan 1, 1992

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By László Guczi1

Nanosize model gold particles with varying size were fabricated by deposition of a 10 nm thick gold film onto SiO2/Si(100) substrate by electron beam evaporation followed by modification using low energy Ar+ ion bombardment. The change in particle size were monitored by the Au 5d valence band states determined by ultraviolet photoelectron spectroscopy (UPS). The gold/iron oxide interface was studied by iron oxide deposition on gold. It was found that the energy profile of Au 5d valence band states are strongly redistributed with decreasing the gold particle size mostly affecting at the lowest and at the highest binding energies. The size effect in the UPS spectra can be interpreted by the energy redistribution rather, than by narrowing the 5d states. The iron oxide deposition increases the catalytic activity in CO oxidation whether it is on gold nanoparticles or on a continuous 80 nm thick gold film. The activity enhancement is significantly larger in case of gold nanoparticles. The interface interaction is operative in enlargement of the catalytic activity even if gold particles are not exposed to the surface, but they are located below the iron oxide layer.

Oct 1, 2003

By K. G. Wheeland, K. G. Byberg

The occurrence of a secondary, dust-fuelled explosion following blasting of sulphide ores has been reported in mines in many countries, including canada, the USA, Australia and South Africa. However there has been little effort to document the events and develop effective control technology. Following a detailed investigation of an incident at the Geco Di vision of Noranda Minerals Inc. , the company held a conference of interested parties in October 1986 to review the state-of-the-art and to agree on action. '!his paper outlines the causes and effects of such explosions, the key conference points and conclusions, and subsequent information-exchange and teclmology-developrnent activities.

May 11, 1988

By Richard R. Klimpel, Simon Isherwood

"The industrial processing of ores containing gold and/or platinum minerals is generally mining site specific, e.g. McQuiston and Shoemaker (1985). The variety of various mineral processing techniques employed is extensive and includes size classification, gravity concentration, amalgamation, roasting, cyanidation, chemical leaching, ion ex-change/solvent extraction and froth flotation. Because of the relatively small quantities of Au and Pt that exist in the earth’ s crust, the economical recovery of Pt and Au often requires that the Au and Pt be associated with other industrially important minerals. This association of Au and Pt with other minerals can occur in very complicated mineralogical forms. It is probably safe to say that Au and Pt mineral concentration from natural ores represents some of the most complex metallurgical challenges facing the mining industry.Froth flotation is a technique that is receiving increasing industrial attention for the treatment of finely disseminated and/or associated Au and Pt minerals. The high throughput at relatively low capital cost, the potentially high selectivity, and the existence of a well-established technology for treating more abundant associated minerals such as base metal sulfides makes froth flotation an attractive processing alternative. Broadly speaking, the industrial oriented froth flotation experience with Au and Pt minerals exists in two major categories: 1) the flotation of Au and Pt associated with pyrite (or pyrrhotite) and 2) the flotation of Au and Pt associated with primarily Cu, Zn, or Cu/Pb/Zn containing sulfide ores.In the case of the precious metal association with pyrite (or pyrrhotite), much of the published froth flotation experience comes from South Africa. Typically, such processes are done using an acid side flotation with a collector such as mercaptobenzothiazole. The approach obviously is to float pyrite and hence recover associated gold. Generally the higher the total sulfur recovery the higher the gold recovery. Similar experiences of Pt associated with pyrite are a lot less common mineralogically and hence less well documented industrially. For example, in Canada, Pt is often associated with pyrrhotite but is not really processed as a straight pyrrhotite recovery.For the situation of Au and/or Pt associated with other base metal sulfide minerals, the industrial experience base is quite varied and is well documented from both North and South American operations. The nature of most of these flotation processes is to design, operate, and optimize the installed concentrator to get the Cu, Pb, Zn, Ni, etc. that is the bulk of the valuable sulfide ore and then take whatever precious metal recovery comes. Typically, such flotations are on the basic side using standard thiol collectors such as xanthates, dithiophosphates, thionocarbamates, etc. It is very common with such ores to use mixtures of collectors in order to get ""everything"". Often in such plants, there is an inherent balancing act occuring so as to operate in such a manner to reject pyrite (and pyrrhotite) in order to maintain high base metal mineral concentrate grades and yet recover sufficient precious metals such as Au and Pt minerals which often are associated with the iron sulfides being rejected. Obviously in such an environment, the smelter operation often ends up telling the concentrator what the precious metal recovery actually was in a given production period."

Jan 1, 1994

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By Pierre Bernard

Contents of the presentation ? Overview of Brunswick 12 Mine ? Brief description of the mine geology ? Summary of the current Mineral Reserves and Additional Mineral Resources ? Review of the ongoing mining remnants evaluation process, particularly emphasizing the integrated work between the mine geologists, the mine engineers and the metallurgists ? Challenges and opportunities to extend the mine life

Apr 1, 2005

By T. Lamb

There are many honor stories about aluminum in the marine environment and many are not based on facts, so they are myths. Myths must be addressed before progress can be made. This paper attempts to dispel the myths and state the facts. A common perception is that aluminum ships cost significantly more than steel ships. This paper illustrates that even though the cost of the aluminum structure is over 50% more than the steel structure, an "equivalent" aluminum naval ship can be built within 7% of the acquisition price of a steel ship. This is possible because of the cascading benefits of the aluminum ship's significantly lighter weight. Aluminum ships also have a life-cycle cost advantage over steel ships because of reduced maintenance and fuel cost savings.

Jan 1, 2011

By K. G. Markkola

The Minera Candelaria concentrator was commissioned in August 1994, and in October 1997 it doubled its grinding capacity. The concentrator was designed to treat 56,000 metric tonnes of copper ore with a primary crusher, two grinding circuits, pebble crushing, and flotation. The grinding circuit includes two 11.2 m (36 ft) diameter by 4.6 m (15 ft) long semi-autogenous (SAG) mills, each fitted with a 12 MW motor. Throughout the history of Candelaria, different strategies have been developed to maximize the plant's operational time, strategies that include increasing the life of the SAG mill liners and reducing the time involved in changing these elements. This work describes the improvements made in the design of the liners, the change planning, and a new strategy to change the liners with the purpose of increasing their use and throughput.

Jan 1, 2007

By J. G. Speight

Laboratory studies indicate that autogenous heating of low-rank coal can be prevented by a prior treatment which involves immersing the coal for short (5-15 min.) periods in an inert liquid at temperatures between ~ 350° and 400°C. Such "carbonization" effectively reduces the accessible pore volume of the coal to levels at which heat generation through subsequent sorption of moisture and oxygen is too slow to cause significant temperature rises in a stockpile. In addition, this treatment also irreversibly removes most of the moisture held in the raw coal and raises its calorific value by as much as 10-12%.

Jan 1, 1973

By S Sokhanvaran

Electrodeposition of silicon from a cryolite based electrolyte at a relatively low temperature (1000°C) is a promising approach to generate high purity silicon. In order to obtain fundamental data pertaining to electrowinning of silicon from Cryolite?SiO2 melts, density and electrical conductivity measurements were made. A range of temperatures and SiO2 contents was studied for each property. It was found that while density has an inverse relationship with temperature, the dependence for electrical conductivity is direct. Increasing silica content up to the saturation limit (~ 5 wt%) increases the density whereas further increase in SiO2, lowers the melt density. On the other hand, the conductivity is lower for the melts with greater SiO2 content, at any temperature.

Jan 1, 2011

"Industry Guide 7 contains the Securities and Exchange Commission’s basic mining disclosure policy. It provides guidance for Registrants on various matters including the definition and disclosure of proven and probable reserves and the definitions of exploration, development and production stages. The definitions and disclosure instructions contained in this Guide apply to all public mining entities and their public disclosures. As NI 43-101 is law in Canada, the SEC allows mineral resources and mineral reserves prepared under CIM Definition Standards for issuers that are reporting in Canada but are also registered with the SEC. The SEC places conditions on the disclosure of these estimates. US shareholders are cautioned that the requirements under NI 43-101 and the CIM Definition Standards differ significantly from those of Industry Guide 7.Note: this Guide contains the Commission's basic mining disclosure policy. The definitions and disclosure instructions contained in this Guide apply to all public mining entities and their public disclosures pursuant to the rules of Regulation S-K. Questions regarding the application of these definitions and rules to specific situations should be asked of the Commission's mining engineers or geologists at either the Office of Engineering, Division of Corporation Finance, 202-272-3252, or the Branch of Geology, Central Regional Office, 303-844-1000.(a) Definitions. The following definitions apply to registrants engaged or to be engaged in significant mining operations:(1) Reserve. That part of a mineral deposit which could be economically and legally extracted or produced at the time of the reserve determination.Note: Reserves are customarily stated in terms of DoreD when dealing with metalliferous minerals; when other materials such as coal, oil shale, tar, sands, limestone, etc. are involved, an appropriate term such as Drecoverable coalD may be substituted.(2) Proven (Measured) Reserves. Reserves for which (a) quantity is computed from dimensions revealed in outcrops, trenches, workings or drill holes, grade and/or quality are computed from the results of detailed sampling and (b) the sites for inspection, sampling and measurement are spaced so closely and the geologic character is so well defined that size, shape, depth and mineral content of reserves are well- established.(3) Probable (Indicated) Reserves. Reserves for which quantity and grade and/or quality are computed from information similar to that used for proven (measured) reserves, but the sites for inspection, sampling, and measurement are farther apart or are otherwise less adequately spaced. The degree of assurance, although lower than that for proven (measured) reserves, is high enough to assume continuity between points of observation.(4)(i) Exploration StageDincludes all issuers engaged in the search for mineral deposit (reserves) which are not in either the development or production stage."

Jan 1, 2003

By Harold Hopkins

THE Wright-Hargreaves mine is one of a group of seven mines long active in the Kirkland Lake district, Ontario. Detailed geological reports and maps covering the area have been published by the Ontario Department of Mines (1,3)t. Though all these mines work several productive veins there is one vein which is common to all and is known as the North Vein of the camp?not that it is the most northerly vein mined, but it is the more northerly of the two major veins of the camp. At the Wright-Hargreaves mine there are in all ten important producing veins, and most of them have a N.60°-65°E. strike and in general a steep southerly dip. It is a common belief that most of these veins lie along faults but it will be shown that whilst this is true of some of them it is not true of all, and also that a vein may lie in a fault along part of its course and elsewhere fill a fracture in line with the fault, this being a consequence of rotational movements that took place during faulting. The paper describes the history of faulting at this mine in particular, makes observations on the principal pre-ore fault, and describes the method used in solving the movements on the post-ore faults. Other details of geology are not discussed except to mention here that our main veins lie almost entirely in the syenite porphyry stock except on lower levels close to the east boundary of the property, where the North vein leaves the porphyry to enter the greywacke.

Jan 1, 1940

By J. A. Finch, M. Mimezami, M. S. Hashemi A.

The adsorption of magnesium and calcium ions on sphalerite and pyrite is discussed. These ions are common in process water and often considered be detrimental in sulphide flotation. The study attempts to characterize the adsorption mechanism, which has been less studied than the oxide system. Generally for oxides metal ion uptake occurs when cations are hydrolyzed. Our findings reveal that magnesium and calcium adsorb on sulphides at pH below hydrolysis, but adsorption is not chemical. At higher pH, charge reversal occurs that does correspond to presence of hydrolysis products. Advances

Jan 1, 2009

By A. Galip Ulsoy, K. V. S. Sastry

"This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology. and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control. IntroductionEconomically accessible higher-grade ores are being rapidly depleted, and at the same time the demand for mineral raw materials continues to increase. Mineral recovery from the remaining low-grade or finely dispersed ores requires grinding for liberation. High energy consumption during grinding and poor efficiency associated with the beneficiation of fine minerals are two important problems facing the mineral industry . These problems, coupled with advances over the last 10 to 15 years in the areas of process modeling, instrumentation, computer technology and control theory, have made automatic control of mineral processing systems an important research area(23,52,66,67,120,129,152)."

Jan 1, 1981

By A. Galip Ulsoy

This review paper is intended to provide, the mineral process engineer with an introduction to the concepts, terminology and practice of mineral process control. It also provides an extensive sampling of the vast body of literature relevant to this topic. The topics discussed include the principles of automatic control, instrumentation, mineral processing unit operations, process modeling and simulation, and process and plant control.

Dec 1, 1981

By D. M. Morrison

"Microseismic systems at five mines in the Sudbury Basin provide the basic data for Falconbridge Limited's rockburst research. Daily and long-term analysis of this data as well as underground observations has confirmed the fault-slip mechanism of rock bursting at three mines. A detailed analysis of the complete history of Falconbridge Mine is being conducted and Distinct Element numerical models are being used to simulate both the stick-slip behaviour of faults and the dynamic effects of the induced vibrations on rock and backfill. University research includes acoustic tomographic imaging of the rock mass based on seismic wave propagation and collection of full micro seismic waveforms to allow application of advanced seismic and statistical analysis techniques. INTRODUCTIONFalconbridge Limited currently has five mines operating in the Sudbury Basin: East, Lockerby, Onaping, Fraser, and Strathcona Mines, which along with the Falconbridge open pit produced 2.8 million tonnes of ore in 1986. The underground mines range from about 600 m to 2000 m below surface and one of the consequences of mining at these depths is the occurrence of rockbursts.Research into rockburst phenomena at Falconbridge began over 25 years ago and research is continuing in an effort to avoid the problem by improved mine design, to protect mine openings from damage by design of effective support systems and to better understand the processes which precede a major fault slip rockburst. Since the early 1980s, significant progress has been made due principally to micro seismic monitoring and advances in microcomputer technology coupled with detailed underground investigations.It is now possible to identify the fault-slip mechanism as the cause of many of the rockbursts which occur at Falconbridge mines. By gaining an understanding of effect of mining-induced stresses on the pre-existing geological structures, areas which may experience rock bursting can be identified and can be protected against severe damage by appropriate support techniques."

Jan 1, 1989

By Mikael Ramström

The IREDES Special Interest Group (SIG) for Drill rigs has been active since its inception at MineExpo 2000, in Las Vegas USA. The SIG for drill rigs is responsible for the development of a IREDES Drill rig profile. This includes the exchange of production planning, performance and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During year 2001 a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies and third party suppliers and reviewed during several SIG meetings. In mid 2002 the profile was released for prototyping projects and since then, feed back received from these projects has been used as input to the first official IREDES release. LKAB and Atlas Copco decided in 2002 to start an IREDES prototyping project using the Simba L6C production drill rig as target equipment. The goal was to verify the drill rig profile and identify possible problems prior to the official release. This was done by implementing the IREDES prototype version in the LKAB?s production planning system and Simba rig control system. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this the mine production system was adapted for drill plan export and logging data import on IREDES format. This paper presents the most recent results of this prototyping project. Result from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES will be a central issue for future mine automation. As a result from this and other IREDES prototyping projects the official IREDES release will be available in 2003. Soon after that release IREDES compliant products can be expected. This will include drill rigs and mine production planning systems.

May 1, 2003

By Michael Hopp

The beginning of the electroforming technology dates itself on the beginning of the industrial revolution 1800 to 1820 approximately. Basis was the existence of electricity in order to be able to drive the electro-form-process. With the development of the electroforming, big names of the science-history, like Michael Faraday (1791? 1867), Sir Humphry Davy (1778?1829), Max Schlöter (1878?1946), Werner von Siemens (1816?1892), and many others. Already about 1840, the first monograph originated to electroforming (38). While in the first years the electro-forming most extensive only to the coating of art - or other usefulness-objects was used. At the beginning of the 20th century the formation of objects from pure metals became more and more, later also from alloys to application. One of the first bigger electroforming factory, the ?Württembergische Metallwarenfabrik? was working 1894 in Geislingen / Steige, Germany. In the industrial application, the electroforming-technology is to be imagined away for miscellaneous coatingtasks and the form-body-preparation no longer today (18). A little bit confusing is the german name ?galvano-technology?. It based on the Italian physiologist and naturalist Luigi Galvani (1737 ? 1798). This technically seen is however wrong, right, the name is electroforming. The physical bases were founded mainly by Michael Faraday and Sir Humphry Davy.

Oct 1, 2003