Search Documents

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951

By D. F. Malan

"This document highlights some of the topical problems associated with the design and support of deep tabular excavations in hard rock. The displacement discontinuity boundary element method has been used for at least five decades to analyse stress and displacement distributions around narrow width excavations with complex plan outlines. The assumption is made in most cases that the rock mass surrounding the excavation is perfectly elastic. Although this approach works well to minimise stress concentrations in practice, it has limitations as important parameters, such as the effect of mining rate, cannot be investigated. Recently, a limit equilibrium model has been studied as a means to enhance standard layout design exercises by including an interactive on-reef damage model. This approach can include explicit energy release dissipation computations. A second problem faced by engineers in the mining industry is the evaluation of pillar and remnant stress. The paper highlights two aspects namely the effect of element size in displacement discontinuity modeling on pillar stress and the difficulty to estimate the effect of total closure on the regeneration of stress in old mining areas. Regarding the support of the tabular excavations, current efforts are focussed on providing improved aerial coverage using hangingwall bolting and temporary nets. An unresolved issue is the installation of permanent mesh in low stoping width areas. INTRODUCTIONSince 1886, more than 50 000 tons of gold has been mined in the Witwatersrand Basin of South Africa (Hartnady, 2009). The nearby platinum mines also saw significant growth in recent years and more than 80% of the world’s platinum group metal reserves are contained in the Bushveld Complex of South Africa (Nell, 2004). Apart from the economic aspects, the mines served as an outstanding rock engineering “laboratory” for many decades owing to the deep, tabular nature of the excavations. The period from 1960 to 1980 was especially lucrative in terms of research and world-renowned researchers investigated the support and rockburst problems (e.g. see Cook et al., 1966; Salamon, 1968; Bienawski, 1973; Wagner, 1984). Many of the rock-related problems nevertheless persist up to the present day and this paper explores some of these problems and recent progress. The production of gold declined substantially in recent years (Hartnady, 2009) and well-directed rock engineering research can play a meaningful role to slow this trend. The objective of the document is to highlight critical areas requiring additional research and not to discuss the topics in detail. The reader is referred to the many references for additional information. The paper only focuses on three areas namely numerical modelling, pillar stress estimation and aerial support. Although these are diverse topics, it is included in one paper to illustrate the many unsolved and practical problems associated with deep tabular excavations."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, R. Tichy, W. Ecker, M. J. Mikl-Resch, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (Figure 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (Figure 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By M. Gimpel, R. Galler, T. Antretter, H. Kargl, M. Mikl-Resch, R. Tichy, W. Ecker, G. Pittino

"A computational method based on a continuum-mechanical approach to simulate rock cutting is developed and evaluated. The aim is to obtain the local loading acting at the cutting pick during operation. The explicit FEM is chosen to model the pick-rock interaction. The presented method takes advantage of (i) an advanced material model (ii) a robust contact algorithm and (iii) fast calculations due to parallelization. A damage-plasticity law is chosen and modified with user-subroutines. A user integrated element deletion routine evades critical mesh distortions. Infinite elements at the model boundaries avoid unrealistic deformation wave reflection.INTRODUCTIONExcavation in mining and tunneling is a costly and complex process. Special equipment such as the roadheader (fig. 1) is employed to cut the rock in the excavation process but high material strengths limit their usability (Tockner 1999). Nowadays a challenge is to extend their field of application to harder and more abrasive rock materials. The forces on the pick (fig. 2) are of great importance and determine wear and especially the efficiency of the machine. Figure 2 shows the principle of cutting and the predominant forces. The variation of pick geometry, cutting depth or attack angle will result in an alteration of these forces and determine the efficiency of the process (Tockner 1999). The mechanisms of rock cutting follow the principle of indentation (Kou et al. 1999). Directly under the indenter a hydrostatic stress state evolves causing the material to fail only due to crushing and fragmentation mechanisms. In the close surroundings large strains emerge and tensile cracks are formed but in a further distance the material behaves elastically."

Jan 1, 2015

By J. -F. Lepage, M. A. Tomlinson, K. K. Murray

"The Éléonore mine, located in the James Bay region of Northern Quebec, generates a gold bearing flotation concentrate rich in pyrrhotite. Direct leaching of the finely ground concentrate results in high cyanide consumptions and poor recoveries, so effective pre-treatment to passivate the pyrrhotite is required before leaching. Following a number of process upsets at the mine, test work was performed to better understand the requirements for passivation so a more effective operational strategy could be implemented. This paper outlines the testing and implementation of the new strategy at Éléonore.ÉLÉONORE CONCENTRATOR The Éléonore mine is located 800 km north of Montreal, in the James Bay Region of Quebec, Canada. The ore, containing gold disseminated in sulfide minerals and free fine gold in silicate gangue, is crushed in a two-stage crusher plant before being ground in a single 9,000 kW ball mill. The ball mill is in closed circuit, with about 25% of the cyclone underflow passing through a gravity plant with two, 48” Knelson concentrators. Gold recovery in the gravity circuit varies between 15 and 20%, with gravity concentrate leached daily in an Acacia intensive leach reactor. Cyclone overflow, at a target P80 of 65 microns, flows to the flotation plant where the gold bearing sulfide minerals, mainly pyrrhotite and arsenopyrite, are recovered to concentrate with a mass pull of about 5%. The flotation concentrate, typically containing between 80 and 120 g/t of gold, is thickened and finely ground using a 1500 kW Isa Mill. The finely ground concentrate is diluted, to generate a slurry with about 32% solids by weight, before feeding the leach plant. Initially the concentrate slurry is pre-treated with oxygen and lead nitrate, to passivate the sulphide minerals before cyanide is added for gold dissolution. Gold is recovered from the leached slurry using carbon-in-pulp (CIP). The flotation tailings are also thickened and gold is recovered in a dedicated leach-CIP plant."

Jan 1, 2017

By A. E. Wraith, R. Harris, J. Qiu, R. Parra

Small pilot scale experiments have shown that it is possible to almost fully eliminate the minor elements (ME), namely As, Sb, Bi and Pb contained in smelter dusts by vacuum calcination of mixtures of the dust with sulphidizing agents such as dirty copper concentrate or elemental sulphur at 900 °C and 80 +/- 30 Pa for 90 minutes. The products of this calcination are a residue comprising a purified mixture of copper containing compounds along with the gangue constituents and a high sulphur condensate comprising a mixture of the minor element compounds. In particular, the Cu:ME ratios of the concentrate and dust were increased from 250 and 50, from 28 and 12 and from 36 and 8 to roughly 3000, 3000 and 100 for the calcine, for Bi, As and Sb, respectively. It has also been calculated that (i) the copper content of the vacuum calcine may be recovered by feeding it into a Peirce-Smith converter during its slag blow, and (ii) the resulting recycling could increase the minor element treatment capacity of a smelter by 100 % while also reducing the blister As content by a factor of three. The experimental results are briefly discussed and a treated dust recycling option is examined. Example operating conditions are presented and available commercial technology for the vacuum calcination of the mixtures is reviewed.

Jan 1, 2007

By C. Tan, A. Putz, P. Lacombe, R. Kemp, M. Kaya, B. J. Huls, A. R. Laplante

"This paper concentrates on the four recent plant trials/ applications of froth washing. Results showed that improved metallurgical performance can be achieved with wash water. Increased froth cleaning yielded better upgrading, and some cases slightly improved recovery. Froth sampling and salt tracer tests supported the findings of froth washing tests.At Falconbridge, Ni grade increased from l.47% to 2.15% and recovery from 85% to 87%. At Eastmaque, final Au grade increased from 2.3 to 2.7 oz/st at a slightly higher recovery. At Les Mines Selbaie, Cu grade increased from 24.5% to 25.S% and Zn grade from 54.5% to 56.l%. At Zinc Corp. of America, average Zn grade increased from 55% to 56. 8% at the same recovery for a 45-day period. A number of plants in Canada and the United States have evaluated and/or now practicing froth washing. Wash water has now proved itself in some plants over several months of operation.INTRODUCTIONFroth washing in mechanical flotation cells offers a number of metallurgical (i. e. increased grades and/or recoveries) and economical (i.e. decreased transportation and smelting & refining costs) benefits. Fundamental development work in laboratory and pilot scales performed at McGill yielded encouraging results. (Kaya and Laplante, 1988a and 1989a). Since laboratory and pilot flotation performance can differ from full-scale due to differences in hydrodynamics, kinetics, and froth characteristics (e.g. stability, loading etc.), plant trials were essential to prove the viability of this technology."

Jan 1, 1990

By Richard W. Hutchinson, Christopher Osterman

Abstract -The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and foot­ wall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fine grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfide piercement structures and the footwall Cu-POE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By F. Siciliano, D. Bai, S. Yue, A. M. Elwazri

The influence of niobium addition and very low temperature (`cool') deformation on the microstructure and properties of low carbon microalloyed steels was investigated. In this work, the specimens were heated at 1200°C and held at this temperature for 20 minutes. Some specimens were aged at 400°C for times ranging from 10 minutes to 10 hours followed by air-cooling. Others were subjected to deformation at 400°C (`cool deformation') prior to aging. It was observed that the proportion of acicular ferrite was increased as the amount of Nb was increased. It was found that cool deformation increased both yield and tensile strengths significantly compared to that of the aged only specimens.

Jan 1, 2005

By Xiaowen (Wendy) Ma, Hans Liang, Xiaoying Chen, David Way

"The mineralogical characteristics of the process streams provide key indicators to the potential improvement in the metallurgical performance. Therefore, the process mineralogy and diagnostic metallurgy have been widely used as a tool to assist the metallurgists at the operating plants. The challenge of this study was then how to characterize the diagnostic flowsheet of the minerals of interest in the process streams across the flotation circuit. The investigation from this study indicates that the minerals chematic flowsheet can visibly demonstrate the sources that caused the gold losses during the mineral processing.In this paper, we present studies of the flotation process stream samples, representing the feeds, intermediate products, final concentrate and final tails, which were produced from the flotation concentrators of Mt Carlton mine in Queensland, Australia. This study was focused on characterizing the process streams and learns how the gold in the process streams was associated with other sulphide minerals and host minerals on a size by size basis. The automatic QEMSCAN/MLA Particle Mineral Analysis (PMA) and Trace Mineral Search (TMS) were applied to identify the minerals and to detect the gold in the sized fractions of process streams. The Laser Ablation ICP-MS (LA) spot analysis, QEMSCAN EDS spot analysis and electron microprobe spot analysis were employed to identify and quantify there fractory gold concentrations in the sulphide minerals, like pyrite, and the elemental concentrations of visible gold grains. The diagnostic flowsheet of gold recoveries by the process streams, by mineral association classes and by the particle sizes were generated and discussed."

Jan 1, 2017

By H. J. McQueen

Pyro-reduction of ores to metal products developed markedly through the industrial revolution into the great depression. Nineteenth century resource and environmental sustainability were haphazardly improved by many process changes, although the motivation was primarily reduction in labor, feed stocks and fuel. Some notable achievements were coke and hot air for blast furnaces (later from waste heat stoves), puddling of wrought iron and steel ingot production with convertors advancing into oxygen use and continuous slab, billet and strip casting. Although advances in one sector were often counteracted by fall-backs in others, there was progress in that the resource consumption and pollution per unit of production was decreased. Improvements in the 2 decades following WW2 were mixed but popular notice of environmental hazards forced governments to legislate pollution controls and initiate steps in resource conservation. The energy crisis of the 1970’s saw an industrial energy-saving campaign and legislation of technology assessment procedures. Up until mid 18th Century, the training of iron masters depended on apprenticeship with some formalized knowledge from medieval books such as those of Biringuccio (1540) and Agricola (1556). The advances were very slow partly due to absence of scientific concepts of the smelting process. Nevertheless, some iron masters succeeded in improving the process and described procedures to instruct others. With the surge of steam power and the reverberatory puddling process for ductile wrought iron (WI), machinery changed from wood (iron strap reinforced) to WI machinery. With the clarification of the reduction and oxidation mechanisms by Cavendish and Lavoisier (~1780), productivity in iron production surged. The mechanical testing and microscopy of Kirkaldy (1862) spurred understanding of processing and properties of WI and steel. The various forms of C in steels were determined by chemists at the end of the 19th Century. It also became possible to control metal and slag chemistry in the open hearth furnace. But understanding of the transformations during heat treatment of steel only came in the first decades of the 20th Century.

Jan 1, 2012

By J H. Dressel, J. E. Williams

This paper presents a brief review of what coal gasification is, procedures that are available today and processes that may be available in the future. Examples are given as to how the process might be used in power plant applications, the effect on pollution level and power costs, and some thoughts on the added burden that might be placed on mining and coal preparation.

Jan 1, 1973

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

By Robert J. Shank

This paper describes the Federal Government assistance available for northern mining development. The paper commences with a discussion of why the Federal Government should give assistance to northern mining development. It then uses a hypothetical case of a company which has a property it wants to develop to list the sectors within the . Federal Government that would have to be consulted in order to obtain federal financial assistance. The paper also outlines the type of information a company must be willing to provide the government in order to qualify for such assistance.

Jan 1, 1978

By F. A. McLean

At the Annual Western Meeting held at Blairmore, Alta., October 1924, the writer presented a paper drawing attention -to the advantages of portable gas-driven equipment for developing isolated mining properties. This type of equipment was at that time practically in its infancy and the details of results actually accomplished were somewhat meagre. During the last year or so a number of these plants have been installed so that it is now possible to offer more definite information regarding the actual mining progress accomplished with such plants and their cost of operation in various parts of the country. This paper has been written with the idea of reviewing the work done during the past year, and to supply data which may be of interest to those wh9 are confronted with the problem of selecting equipment for development or assessment work. Because drilling operations play such an important part in mining, one of the first problems that usually confront the prospective? mine owner is the selection of the proper com-pressed-air plant. The size and type of equipment and the method of driving it require careful consideration. The size and type of equipment is determined largely by the funds available, transportation facilities, and the speed with which the programme of development is to be carried out. The selection of the proper method of drive usually depends on local conditions, such as the relative cost of various fuels, and has an important bearing on operating costs.

Jan 1, 1926

By Michael P. Davies

Mine waste facilities, and in particular tailings impoundments, are one of the highest risk aspects of any mining venture. There are far too many recent examples of how real and/or perceived physical or environmental impact from one of these facilities has had enormous economic impact on both the specific project and the overall parent mining company. In many cases, such dramatic impacts have followed a period where a due diligence of the mine had been carried out (e.g. in an acquisition, merger or similar) or an internal or otherwise audit had taken place. Consequently, it is suggested that there is a need for an audit/due diligence framework to assist those processes in terms of assessing mine waste facilities. This paper presents a recommended framework for completing either an audit or due diligence assessment of mine waste facilities under a number of typical scenarios. The framework will be of relevance to reviews carried out prior to mine construction, during operations and for mines that have been in a care and maintenance position and are to be re-opened. Concepts of risk management are introduced as an essential part of the recommended framework. The paper should be of value to current and prospective mine owners involved in stewarding an area of significant risk to viability of their mining venture. The paper should also interest prospective lenders to these ventures.

May 1, 2007

Presentation Outline ERM ? corporate profile Background to sustainability reporting GRI G3 Guidelines (Oct 2006) Best practice examples Contact information ERM ? corporate profile Over 35 years of experience World?s largest all-environmental consultancy* 130+ offices in 40+ countries; 3,200+ professional staff Worked with >50% of the Global Fortune 500 (FY07) Annual turnover > US$500 M (FY07) 2008 Environmental Advisor of Year** Offices/Staff ? Canada (5/50) and US (65/1,350) *Source: Engineering News Record: July 2, 2007 ** Source: Acquisitions Monthly: December 2007

May 1, 2008

By P. Nos, L. Kolbeinsen, M. W. Kennedy, A. Filzwieser, R. T. Jones, A. MacRae

Modern furnace designs often incorporate extensive use of cooled elements to achieve long campaign lives at high operating intensities. However, contact between water and high temperature fluids can result in powerful Boiling Liquid Expanding Vapour Explosions (BLEVEs). Therefore cooling such elements with water carries inherent risks when used under slag and particularly below molten metal or matte. Alternative cooling media exist that can reduce or eliminate the risk of BLEVEs. These media are analysed and discussed in the context of deeply cooled furnace elements. Important factors in selecting alternative coolants are explored including: critical heat flux, thermal limits, toxicity, flammability, unit cost, etc. Key cooling system design criteria are reviewed in the context of both traditional and alternative coolants. Results of Computational Fluid Dynamics are presented for an example tap-block cooler design using a number of selected coolants. Research needs to advance the safe use of alternative coolants are presented.

Jan 1, 2015

By J. A. González-Anaya, F. Nava-Alonso, O. Alonso-González, F. Alvarado-Hernandez, A. Uribe-Salas, C. Jimenez-Velasco

"One of the most common hydrometallurgical methods for precious metal extraction is cyanidation. The effluents of this process may contain relatively high concentrations of copper, zinc and iron, which react with free cyanide to form complexes, adversely affecting the efficiency and the economy of the process.This preliminary work studies the use of the solvent extraction technique to remove copper, zinc and iron cyanide complexes from a synthetic solution similar to that of gold mill effluents, in order to allow the recycling of the solution back to the process. For the extraction of these anions (Cu(CN)2 -, Cu(CN)3 2-, Cu(CN)4 3-, Zn(CN)4 2- and Fe(CN)6 3-), trioctyl methyl ammonium chloride (Aliquat 336) was studied as extractant, using nonylphenol as modifier in the organic phase (iso-octane). The experimental results showed that for a synthetic solution containing 450 mg/L total cyanide, 160 mg/L copper, 50 mg/L zinc and 51 mg/L iron, it is possible to extract the 96% of copper, 91% of zinc and 75% of iron when using 0.011 mol/L of Aliquat 336 (organic/aqueous volume ratio (O/A) =1) in the pH range of 9-10."

Jan 1, 2014

By S. A. L. Read

"The intact rock constant, mi, is one of the three basic input parameters required for the widelyused Hoek-Brown failure criterion. Values for the constant should ideally be determined by statistical analysis of laboratory test data. In this paper the influence of the inclusion or exclusion of tensile test data on derived values is discussed. We firstly investigate the relationship between direct tensile strength (DTS) test values and Brazilian tensile strength (BTS) test values based on a literature search, finding that the correlation between the two test types is DTS = 0.9*BTS, independent of the lithology being tested. Secondly, using the shear strength database of Douglas (2002), we examine the influence of confining pressure range and the inclusion or exclusion of DTS and BTS test values on calculated values of mi.Chief amongst the influences was the exclusion of tensile data in the calculation procedure, particularly when the Hoek triaxial confining stress range requirement (?3?max = 0.5?c) was not satisfied. Based on a reasonable 1:1 relationship between R (the ratio of unconfined compressive to tensile strength), use of actual tensile data in the calculations for the Hoek brown failure criterion is considered to be a simpler and more robust approach to the use of a tensile cutoff based on empirical criteria such as that of Fairhurst (1964). We advocate the fitting a failure curve using compressive and tensile test data as the most reliable means of calculating mi, while at the same time satisfying requirements as originally advocated by Hoek relating to the appropriate triaxial confining stress range (?3?max = 0.5?c) and sufficient (>5) evenlyspread data points. In the absence of triaxial data the use of R provides a practical means of obtaining estimates of mi that are more robust than guideline values."

Jan 1, 2015