Search Documents

By M. Grenon

"The presence, size, orientation, nature, and persistence of geological discontinuities dictate the behaviour of a rock mass. Block size, which is defined by discontinuity spacing, by the number of joint sets, and by the persistence of the discontinuities delineating potential blocks is an important indicator of the degree of fracturing of a rock mass. Consequently, block size is represented either explicitly or implicitly in all rock mass classification systems employed for analysis and design of surface and underground mining structures. Insitu block size distributions may provide a better means to describe the structural complexity of a rock mass. These are the distributions that would be derived if the in-situ rock mass was separated into its constitutive blocks, delineated by existing discontinuities, and each block measured. This paper presents the results of a field campaign at Louvicourt Mine aiming to characterize the rock mass using different methods for determining block size and block size distributions. IntroductionGeological structural data are used to provide input data for analysis and design methods for surface and underground structures. As the collection of structural data involves considerable investment of time and effort, it is sometimes overlooked, thus denying an important source of information for mine design. What is somewhat surprising, however, is that when structural data are available, they are not used to their full potential. Recent work has shown that data on block size have potential applications in different areas of rock engineering:• Blasting — Hudson (1993) has described the excavation process as the change of a preexisting natural block size distribution to the debris fragment size distribution (Fig. 1). Lizotte and Scoble (1994) have reviewed previous efforts on integrating site specific geological conditions into blast design. Grenon et al. (1997) provide a case study where in-situ block size distributions are compared to photogrammetric studies of blasted rock.• Rock mass classifications — Block size is used in the majority of rock mass classification systems either explicitly, as in the RMi classification system Palmstrøm (1995), or implicitly, such as in the NGI system, Barton et al. (1974)."

Jan 1, 1998

By K. J. G Hedges

"Once a health based guidance limits for exposure to diesel exhaust have been established, and as part of a multi-disciplinary team, the program for exposure reduction should incorporate the plan-do-check-adjust cycle. Setting a suitably protective (health based) occupational exposure limit (OEL) for diesel particulate matter (DPM) and nitrogen dioxide is a key driver to reduce exposure. It is important to go beyond regulations and reduce exposure to diesel exhaust, DPM, as low as reasonably achievable (ALARA) such as that prescribed under the Australia, Queensland Mining and Quarrying Safety and Health Regulation 2017 where under section 135 Limiting workers exposure, the workers exposure must not exceed the exposure limit applying to the worker for the hazard; and is ALARA. It appears that previously acceptable OELs are no longer safe. Therefore it is important that the internal responsibility system be implemented and the precautionary principle approach be followed, especially as it may be some time before a suitably protective OEL specifically for DPM is in place. One leading multi-national mining company BHP Billiton has acknowledged a significant lag that exists between regulatory action and the level of science that informs health risk. This company is managing exposure to diesel exhaust to as low as technically feasible. This same company that has set an interim target for managing diesel exhaust to 0.03 mg/m3 is achieving these levels which paves the way for other mining companies and general industry including construction. The Occupational Cancer Research Centre 2017 recommends reducing personal exposure to within 0.02 mg/m3 (EC) for underground mining and 0.005 mg/m3 for other workplaces. Controlling DPM is important to prevent cancer however it is also important that that nitrogen dioxide (NO2) be reduced (ALARA) and that careful selection of control technology be considered such as the proper selection of a diesel oxidation catalyst so that the level of NO2 does not in fact increase. The example from BHP Billiton provides a leading practice including using a multi-disciplinary approach and the importance of controlling emission at source and having an auditable diesel emissions based monitoring program in place."

Jan 1, 2019

By O. Lashkari, A. Charette, R. Ghomashchi

Conventional casting at low pouring temperature was employed to produce semisolid metal, SSM, billets of A356 Alloy. The deformation behavior of the as-cast SSM billets was studied using parallel plate compression viscometry. The compression tests were carried out at different applied pressures, and fractions solid. The rheological studies were conducted assuming the SSM slurry behaving like Newtonian and non Newtonian fluids respectively. The calculated viscosity numbers confirmed pseudoplastic behavior of the SSM billets and were correlated to fraction solid and shear rate proposing the following empirical equation which is valid at low shear rates, less than 0.01 s-1, and fraction solid of0.33-0.46: 0 log77 =5.56-l.38fs -(l.56fs +0.14)logy Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by G. Dufour, F. Paray and J. Tessier 0.33<fs<0.46

Jan 1, 2006

By Larry J. Hulbert, Louis J. Cabri, John L. Campbell, Gilles Laflamme, Chris G. Ryan, Soey H. Sie, Rolando Lastra

"Abstract- The mineralogy of samples from the Wellgreen Cu-Ni-Pt-Pd deposit, Yukon Territory, is complex and the metals of interest are contained within fme-grained minerais which vary in size and mineral associations from sample to sample.The major Ni carriers are pentlandite and violarite; the major Cu carrier is chalcopyrite. About 700Jo of the major Ni carriers and 78% of the major Cu qmier will be liberated at a grind of 80% -&apos;}f,.7 J.Uil (-500 mesh) for typical low-grade gabbro (West zone, sample No. 1). For typical ""clinopyroxenite"" (West zone, sample No. 2) and typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3) the liberation would be 71""lo and 65% for Ni, 74% and 60% for Cu, respectively. Fine grinding, however, cannot liberate the Ni contained in silicates and pyrrhotite, estimated to total24.5% for typicallow-grade gabbro (West zone, sample No. 1), 15% for typical ""clinopyroxenite"" (West zone, sample No. 2), and 12% for typical ""clinopyroxene-rich peridotite"" (East zone, sample No. 3).The principal Pt carrier (sperrylite) varies considerably in grain-size between samples and fme grinding, required to liberate the major Ni and Cu carriers, may be counterproductive in samples where sperrylite is relatively coarse-grained, as sorne would then be unrecovered (e.g. sample No. 1). In addition, sperrylite in samples No. 2 and No. 3 is closely associated with magnetite.Palladium occurs in diverse ways. It occurs in the form of several Pd minerais (e.g. sudburyite, testibiopalladite, merenskyite), as a replacement for Ni in several tellurides, antimonides and tel­ lurantimonides (e.g. melonite), or as very low concentrations in pentlandite (up to 34 ppm), chal­ copyrite (up to 9 ppm), and pyrrhotite (up to 5.6 ppm). Palladium minerais and Pd-bearing minerals are strongly associated with chalcopyrite in sample No. 1 and will thus report to a Cu concentrate. However, 22% of the total Pd is in solid solution in pentlandite in this sample and will thus report to the Ni concentrate. In samples No. 2 and No. 3, less Pd occurs in solid solution in pentlandite, and the PGM are distributed mainly among pentlandite, chalcopyrite, and magnetite in sample No. 2, and among pentlandite, pyrrhotite, chalcopyrite, and magnetite in sample No. 3. Therefore, the feasibility of magnetic concentration should be investigated for samples like No. 2 and No. 3, in order to improve Pt and Pd recoveries.Rhodium was found to occur as rare hollingworthite, in sparse cobaltite (up to 2.7%) and, as low concentrations in chalcopyrite (to 10 ppm) and pentlandite (to 12 ppm) by proton microprobe. Iridium occurs in hollingworthite (up to 7.8%) and very rarely as the native metal or in an undefmed Re-Ir-Os-Ru alloy. Ruthenium was determined by proton microprobe analyses to occur in pentlandite (up to 13 ppm) and chalcopyrite (up to 10 ppm), in addition to rare laurite and Re alloy."

Jan 1, 1993

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls? life and facilitating rolls? change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

By R. D. Westervelt

IN JULY 1954, the first iron ore from the deposits in the Knob Lake vicinity was mined and shipped to Seven Islands. The beginning of the production may well be the greatest advance in Canadian economy in the past fifty years. In 1955, the Canadian iron ore output was more than twice that of 1954, an in-crease due principally to the iron ore shipments from the Knob Lake area. Previous to this, Canada&apos;s iron production was 1.85 per cent of the world&apos;s output. Now, this percentage has risen to approximately 5.5 per cent and shows every indication of increasing further as the production rate from the area is increased. In 1955 the Iron Ore Company of Canada shipped over 7 million tons of iron ore and expects to ship over 10 million tons in 1956. Present facilities may be enlarged to handle up to 20 million tons per year. If the expected I 0 million tons per year are exported, Canada&apos;s iron exports will be second only to her wheat and newsprint exports. Before production began from the Knob Lake deposits, years of development were necessary in the area. Geologists spent several summers mapping the general area in order to unravel the complicated stratigraphy and petrology. Particular attention was paid to the mapping of the iron formation and all stages of alteration from fresh iron formation to ore were observed.

Jan 1, 1957

By J. P. Harrison, R. Roostaei

"In this paper we investigate the consequences of using conventional triaxial peak strength criteria in the polyaxial stress conditions that occur around the end of a long circular underground opening. A series of 3d boundary element analyses were performed using Examine3D to determine the stresses induced around the tunnel in different in-situ stress conditions. To discuss the applicability of a triaxial strength criterion in failure prediction, strength factors were computed for both the Ottosen polyaxial strength criterion and the triaxial Hoek-Brown criterion. Assuming that the Ottosen criterion is an accurate indicator of strength factor, the discrepancy from this value due to the Hoek-Brown criterion is the error in prediction.In order to simultaneously show the error in prediction and actual strength factor, a quantitative bivariate colour scheme is used to visualize the results. This allows rapid identification of regions with large error, and where either unsafe or overly conservative conditions occur. We show how the inappropriate use of triaxial criteria rather than polyaxial criteria leads to an under- or over-estimation of strength factor, and can result in uneconomic or unsafe design. Extending the analysis to different in situ stress regimes shows how the in situ stress conditions affect the assessment."

Jan 1, 2015

By Greg Gosson, Larry B. Smith

"These are heady times for the mining industry, with strong metal prices, investor enthusiasm for the junior explorer and ready access to finance for mineral projects. Many projects were shelved in the past because of technical deficiencies — insufficient tonnes or grade, metallurgical problems, the deposit was too deep or too narrow, or the project was physically or economically under water. With the possibility of sustained metal prices, now is the time for those previously “challenged” projects to be re-evaluated and financing sought for continued development. The question is, do these deposits have reasonable prospects for economic extraction, as required by all mineral resource reporting codes? NI 43-101 defines a mineral resource as that portion of the mineral inventory that has reasonable prospects for economic extraction. However, a mineral resource is not simply an inventory of all blocks above a given cut-off grade. The spatial distribution and geological and grade continuity must also be considered. The qualified person (QP) must consider factors significant to project economics at the mineral resource estimation stage, and not just when qualifying mineral reserves. CIM Best Practice Guidelines for estimating mineral resources require the factors significant to project economics be current, reasonably developed and based on generally accepted industry practice and experience. In establishing the cut-off grade, it must realistically reflect the location, deposit scale, continuity, assumed mining method, metallurgical processes, costs and reasonable long-term metal prices appropriate for the deposit. Variations within the resource model (rock characteristics, metallurgy, mining methods, etc.) may necessitate more than one cut-off grade or economic limit in different parts of the deposit model. There must be sufficient knowledge of the metallurgical characteristics of the deposit, which should be supported by preliminary metallurgical test results."

Jan 1, 2003

By JOHN H. HUDSON

Ceramic clays of the Prairie Provinces range in age from Lower Cretaceous to Pleistocene and Recent. Two significant ceramic clay horizons are the Paleocene Willo wbunch Member of the Ravenscrag Formation in Southern Saskatchewan and the Upper Cretaceous Whitemud Formation, which is found in Saskatchewan and Alberta. The Willowbunch Member is worked at one locale in Saskatchewan; the Whitemud Formation is worked at several locales in Saskatchewan and Alberta. Bentonite operations are found at Morden in Manitoba, Rosalind and Onoway in Alberta, and Wilcox in Saskatchewan.

Jan 1, 1984

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By M. S. Diederichs, J. Oke

Surface limitations and a need for more direct transportation routes require serious consideration be given to the development of underground construction works in geotechnically unfavourable conditions. Due to geographical and logistical limitations, the construction of these underground works is restricted to difficult ground conditions that require temporary pre-support before excavation in order to avoid tunnel collapse or severe surface settlement. One type of pre-support is the umbrella arch system, which has been gaining popularity due to cost and time commitment in comparison with other pre-support systems (e.g., ground freezing). The umbrella arch system has been employed with significant frequency around the world, yet without a complete understanding about the mechanical response of the system. As such, literature has found the temporary support system to be both under and over designed with regard to safety and/or economical impact. The authors of this paper have made three major contributions to increase understanding of the umbrella arch system and to help optimize the design process. Firstly, the authors have developed nomenclature in order to categorize and define umbrella arch elements and systems, which also stimulated the creation of the empirically driven Umbrella Arch Selection Chart. Secondly, the authors have established a design methodology that is primarily based on advanced numerical modelling techniques to aid in the optimized design of the umbrella arch arrangement for site specific conditions. Thirdly, the authors have developed a semi-analytical model for umbrella arch systems employed in squeezing ground conditions by incorporating elastic foundation theory as well as convergence confinement theory. These three major contributions to such a widely employed tunnelling pre-support system will be introduced and explained in detail, and will include discussion of how each is incorporated in the complete tunnel support design process and throughout the construction and monitoring phase of a project.

Jan 1, 2015

By L. St-Georges

In aerospace and transportation industries, severe problems are related to fatigue failure. Aluminium is frequently used in these industries to optimize the solidity and minimise the weight of the structures. Nevertheless, the fatigue life of aluminium alloys is limited and specific efforts have to be made to reduce the vibratory stresses in the mechanical parts. When riveted, the life of the sheet metal structures can be increased compared to welded structures, due to the energy dissipated by the friction between the rivets and the sheet metal and the sheets themselves. In the past decade, a new tool was developed to assemble aluminium structures; the friction stir welding. With this new technique, fatigue life of the aluminium welded joints can be increased by a factor from two to ten. However, less energy can be damped by the friction between the components and increased vibratory stresses may occur. In this investigation, the potential of the friction stir welding to create damped aluminium sheet metal structures is evaluated.

Jan 1, 2006

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By C. H. B. Leitch, T. N. MacAuley, R. L. Linnen, A. E. Williams-Jones

"The Trout Lake stockwork molybdenum deposit is temporally and spatially related to the emplacement of a late Cretaceous granodiorite-tonalite stock in southeastern British Columbia and contains an estimated 49 million tonnes grading O.I9% MoS2- No metal zonation patterns are apparent, with the exception of peripheral tungsten skarn, and exploration was guided largely by geological interpretation. It is typical of the granodiorite, or fluorine-poor type of molybdenum deposit. Molybdenite is contained within a quartz-feldspar vein stockwork and coeval dissemination in igneous (and less commonly metasedimentary) hosts. In general, molybdenite is strongly associated with alkali feldspars, but in detail it is intimately associated with incipient muscovite replacement of albite and K-feldspar; veins that lack feldspars are also typically barren of molybdenite. These textures suggest that fe/dspathic alteration (and precipitation in veins) was an important precursor to mineralization, and the occurrence of similar textures elsewhere (e.g. Henderson) suggest that early feldspathic alteration is important to the genesis of molybdenum deposits in general. Molybdenite deposition at Trout Lake was preceded by contact metamorphism, skarn and potassic alteration, and was overprinted by muscovite-ankerite (phyllic) alteration. Only moderate temperature changes are recorded by the metamorphic and alteration mineral assemblages (350°C to 450°C}; however, with time, fluids became increasingly more acidic and enriched in C02- In light of the intimate molybdenitemuscovite intergrowths, the decrease of pH probably exerted a major control on mineralization.IntroductionGranite-hosted molybdenum deposits can be classified in terms of the composition of the related intrusion, e.g., the granodiorite and granite types of Mutschler et a!. (1981), or the calc-alkaline, alkali-calcic, and alkalic types of Westra and Keith (1981). They have also been classified on the basis of their fluorine contents (Theodore and Menzie, 1984) with the fluorine-rich and -poor varieties roughly corresponding to granite- and granodiorite-type deposits, respectively. For economic reasons, most exploration and research has concentrated on the high-grade/large tonnage granite-type of deposit, exemplified by Climax. F1uorine-poor, granodiorite-type deposits are, however, the most common type in Canada and have been mined in the past (e.g., Endako). In this paper, the authors summarize the research that has been carried out on the fluorinepoor Trout Lake deposit (Boyle and Leitch, 1983; Linnen, 1985; Linnen and Williams-Jones, 1987; 1990) and use what has been learned to develop guidelines for the future exploration of fluorinepoor, granodiorite-type molybdenum deposits."

Jan 1, 1995

By K. Lillkung, J. Kourunen, M. Latva-Kokko

"Carbon-in-leach (CIL) and carbon-in-pulp (CIP) processes utilize activated carbon to adsorb solubilized gold for recovery. Due to carbon attrition and non-ideal carbon management, however, some of the gold is lost in carbon fines and to the solution. The carbon attrition mechanism inside CIL/CIP reactors is mainly abrasion-related. This is critical to gold loss since gold loading takes place predominantly in the outer shell of the carbon particles. Thus fine carbon dust has a relatively high gold content and such a small particle size that it cannot be captured with safety screens. The attrition rate depends on ore and carbon characteristics, but it is always proportional to the mixing power intensity. This rate can be minimized by continuous suspension level measurement and control of agitation speed. In addition, a novel tank bottom structure can significantly reduce the required mixing power input compared to a flat bottom tank. A major challenge in carbon management is infrequent and inaccurate measurement of carbon concentration in the reactors. In order to reduce soluble gold losses by means of improved carbon management, Outotec has been developing a continuous in-situ measurement for carbon concentration that is tolerant to changes in slurry density.INTRODUCTION Cyanide leaching has been utilized since the late 19th century as a standard technology for hydrometallurgical gold production. Since then, gold and silver recovery rates have increased due to technological development, but very similar recovery methods are still being used. The original recovery method was to use zinc precipitation – similar to the Merrill-Crowe process, which is still common for feed materials with low throughput and high silver content. However, in most cases, activated carbon recovery is preferred due to its improved efficiency. The carbon-in-pulp process (CIP) and its modification, carbon-in-leach (CIL), have a lower residual soluble gold level and are not similarly affected by soluble base metals. The main alternative for the use of carbon is ion exchange resins. The principle of resin processes is similar to the CIL/CIP processes, with a different type of adsorbent material. Carbon processes are usually preferred over resin processes due to the significantly higher cost of resin material and the possibility to use simpler, well-established technology with carbon processes."

Jan 1, 2017

By F Kelly

"A central composite experimental design was used to determine empirical relationships between the operating variables of a ball mill and the characteristics of the ground products. The independent variables selected for the study were the work index and size distribution of the feed material, the feed rate and the pulp density. The measured responses included product size distribution, product surface area, viscosity of pulp discharge, weight of dry solids in mill, mill time constant and emitted sonic vibrations. The ball mill was operated continuously in open circuit during each experimental run.Multivariable regression techniques were used to derive linear empirical models from the experimental results. Of the four factors studied, the grindability of the feed material significantly affected every measured response. The size distribution of the ground product was affected significantly by the feed rate and the size distribution of the feed, but not by the pulp• density. Feed throughput capacity and pulp density were significant to the viscosity of the pulp discharge, the weight of solids in the mill and the mill time constant. Significant first-and second-order models are given for the above relationships. The relation-ships between the characteristics of the sonic vibrations of the operating mill and the various dependent variables have not as yet been established."

Jan 1, 1970

By R. W. Wein, L C. Bliss

Northern ecosystems are dominated by a harsh physical environment which dictates a need for biological adaptation. As yet, it is unknown just how these adapted plants and animals will tolerate industrial development. Our work, sponsored by university, government and industry, is part of an effort to evaluate this developmental impact. Our present studies and the results to date will be discussed. Other problems to which the environmental student may address himself in the future to ensure against environ-mental degradation will be suggested.

Jan 1, 1971

By A. D. Pittuck

Refractory minerals .containing uranium and columbium have been successfully treated at Queen&apos;s University, Kingston, to produce high-grade concentrates. Recoveries of over 90 per cent of the uranium and columbium have been obtained when treating concentrates containing euxenite, fergusonite, betafite, and pyrochlore. The processes ?consisted -of leaching the columbium with hydrofluoric acid, and the uranium with nitric acid, sulphuric acid, or sodium carbonate solutions. The leach liquors were extracted with organic solvents from which the values were stripped and precipitated, producing final products assaying 45 to 55 per cent Ob2O5 and 60 to 70 per cent U3Os.

Jan 1, 1958

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By D. Auerswald, M. Kotze, V. Yahorava, T. Udayar

Uranium can be recovered from lower grade uranium ores (<800 mg/kg U3O8), leach residues, and waste dumps cost-effectively via resin-in-pulp (RIP). Using this technology, no solid/liquid separation or washing of the leach residues are required. Furthermore, the uranium recovery can be higher than with conventional methods. RIP technologies have, however, been perceived negatively due to concerns around potential resin fouling and losses. This paper highlights the advancements made in RIP and discusses a number of potential applications where the technology could deliver economic and consequential environmental benefits by reducing the uranium levels in the waste.

Jan 1, 2014