Search Documents

By Sakellariou M., Ferentinou M.

Determination of the nonlinear behavior of multivariate dynamic systems often presents a challenging and demanding task. Therefore, complex geomechanics systems are an ideal area for the application of intelligent methods. Often the physical problem is controlled by nonlinear equations, conveying to the use of neural networks. Hudson, (1992a), aiming at efficient engineering modelling and design, introduced and developed Rock Engineering Systems (RES) approach, through the implementation of generic interaction matrix GIM. This approach has been used for a wide variety of rock engineering and other problems, resulting in many case studies available, which illustrate the application of RES to rock engineering problems. Considering the spectrum of the coding methods for the Generic Interaction Matrix, we suggest an objective coding approach. Among the five proposed coding GIM methods, the coding method according to the slope of Pi and Pj relation is relatively accurate, but it might be difficult or impossible to establish or estimate the exact relation of Pi vs Pj for most of the variables involved within a rock engineering system. Self organising maps, are a special type of unsupervised artificial neural networks, which can learn from complex, multidimensional data, and transform them to visually decipherable clusters. The proposed, coding of the GIM, is performed through the combined use of scatter plots produced through, (SOM), and the coding according Pi vs Pj slope. Naghadehi et al., (2013) constructed a database of worldwide experience, in open-pit mine slope stability, the selection of the principal factors was based on Hudson (1992a) who proposed an ‘atlas’ of factors affecting the stability of rock slopes. Slope classification was performed according to status of stability. The rating of the GIM matrix was completed, coupling scatter matrix produced by SOM training, and Pi vs Pj slope plot. Results refer to the identification of clusters, according to status of stability within the original multivariate data set, and the rating of the principal factors according to the dominance and interaction intensity within the open pit mines RES.

Jan 1, 2015

By D. Gaboury

Most hydrothermal gold deposits contain quartz with fluid inclusions that record composition and temperature of the mineralizing event. Quartz has strong chemical and mechanical resistances to weathering and abrasion. Hence, quartz fragments occurring on weathered surfaces or in till cover have the potential to be used for gold exploration as far as we know what is the signification of the volatile content of the fluid inclusions for gold mineralization. In this perspective, fluid inclusions were analyzed in pure quartz by solid-probe mass spectrometry from gold deposits hosted in the Archean Abitibi (Canada) and Paleoproterozoic Birimian (Western Africa) belts. This approach provides the relative abundance of volatiles from families of fluid inclusions decrepitating at specific temperatures (Td). Fluids in gold deposits are aqueous-dominated with CO2 and minor H2S in accordance with their fundamental role as gold-ligands (H2S) and for pH-buffering (CO2) of the gold-bisulfide solubility. However, there is no correlation between CO2 and H2S contents of fluid inclusions with the gold grade of the samples. This suggests that trapped fluids represent a marginal portion of the fluid history recorded by the veins. However, in barren quartz veins away from known mineralization CO2 or H2S are commonly absent. Wide ranges in H2O Td from 250 to 450°C and CO2-H2O Td offsets are common, indicating phase separation. The content of other volatiles seems to be more dependent on the geological setting. Helium content may suggest proximity to a crustal-rooted fault, a critical parameter for gold mineralization. Methane and especially C2H6 appear to be indicative of fluid buffering by organic-rich material such as graphitic-shale. These rocks may provide an important primary gold reservoir from sedimentary metal-rich pyrite. Nitrogen-bearing fluids may be related to a magmatic component but can also be derived from organic-rich sedimentary rocks. For gold exploration, quartz containing CO2- H2S-bearing fluid inclusions and having H2O-CO2-Td offsets within 250 - 450°C has strong vectoring potential.

Jan 1, 2011

By Alfred B. Annor

The introduction and application of paste backfill over the past two decades has resulted in substantial benefits being realised by many backfill reliant mining operations who have used this technology. Paste preparation over this time period has relied basically on mechanical dewatering approaches that have included the use of centrifuges, thickeners, and vacuum and pressure filtration. In large bulk mining operations, this method of paste preparation has usually involved the construction of big and complex surface plants to meet large tonnage demands. These large plants usually have attendant high capital, maintenance and operating costs. The application of paste backfill in narrow-vein mining requires more flexibility in terms of fill preparation, transportation and placement. The method of paste fill preparation should take into consideration low manufacturing and operating costs, ability to use existing facilities at mine sites, simplicity of operation and flexibility of preparing fill over a broad range of consistencies. This paper will review alternative paste fill preparation methods and indicate those that might be better suited to narrow-vein mining.

Oct 1, 2001

By A. H. Lang

"The Cordilleran region of western Canada includes most of British Columbia and the Yukon and pares of Alberta and the Northwest Territories. The western part of this region was for about 50 years the principal mineral producing area of the Dominion. It lost this distinction in 1907 when production from the mines of the Canadian Shield took the lead, but it continues to provide about 15 percent of the total Canadian production. In 1945 the total mineral production of British Columbia and the Yukon was valued at $65,302,900, of which about 80 percent was derived from metals.This paper is intended to serve as an introduction co the more derailed Cordilleran papers. Part I includes a brief synopsis of the complex geology and diverse types of mineralization in the region and Parr II collates the main structural principles exemplified in the derailed papers, and draws some conclusions regarding the application of this information to prospecting."

Jan 1, 1954

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By R. H. Chambers, L. Alderman

"The paper is introduced by an examination of the factors which have led to the present world-wide interest in charging preheated coal to coke ovens. Various possible methods of preheating and charging the coal are considered and reasons are given for the adoption of the methods chosen. The design of the pilot preheating plant for the British Coke Research Association is discussed and its influence on the design of the commercial units for the South African Iron and Steel Corporation's plant at Pretoria and the British Steel Corporation's plant at Beighton are explained. Operating procedures on the pilot plant are described, particularly with regard to the charging of the preheated coal. Design features of the commercial installations, engineered by Simon-Carves Ltd., are explained with emphasis on the built-in safety of the control system of the preheating plant, and the particular problems associated with the erection of such plants on working coke oven batteries. Commissioning and operating procedures are described and the problems associated with the integration of the preheating plant into the normal pushing schedule of the plant are discussed. Preliminary operating results with regard to the effect of preheating on coal throughput on the commercial plants and on the properties of the coke produced are given."

Jan 1, 1972

By Brian W. Mackenkzie, Jozef Lajzerowicz

This paper is intended to familiarize planners in the noncommunist world with the district planning approach used in eastern Europe for mining development. It deals generally with the basic nature of the district planning problem, the planning process for mining development and the state organization for the planning of mining districts. A number of applications of district planning techniques to both established and new eastern European mining districts are described.

Jan 1, 1971

By Laxman M. Amaratunga

Laboratocy flarmnability tests were perfonned on dust samples from Fraser Mine in a 1.2 L Lindenburg horizontal tube furnace to detennine the percentage of sulphur oxidized during ignition. The explosion pot ential of sulphide dusts depends on their degree of spontaneous oxidat ion, which was measured by the quantitative analysis of so2 gas released during ignition. Test results indicated that dusts with low sulphur content could exhibit a higher degree of oxidation than a sample with high sulphur content. txlst characterisation using image analysis techniques suggests that the structure and the texture of dust are important factors influencing the explosibility of sulphide dust at ignition temperatures. Therefore for safe mine operations% sulphur content cannot be considered as a reliable single index that could be used to predict the potential of a sulphide dust explosion. Physical, chemical and mineralogical characterisation of dust plays an important role in the detennination of suitable indices for the prediction and prevention of sulphide ore dust explosions.

May 11, 1988

By J. Girard, V. Aubé, M. Barakate, S. Bellec, M. R. Eddahabi, Y. Chaik, M. Deshaies

"The activated carbon used in the carbon-in-leach (CIL) process to absorb gold is subject to breakage. This carbon breakage can be minimized, but it will always be necessary to deal with fine carbon particles, known as carbon fines. These fines contain a significant amount of gold and mining operations generally struggle with the treatment of this product. Since IAMGOLD’s Essakane mine is located in Burkina Faso, shipping carbon fines out of the country was not considered a viable solution due to the logistical burden and legal procedures in place. A benchmarking study demonstrated the complexity of treating carbon fines on site. IAMGOLD partnered with the host government to find an innovative approach to economically recover the gold locked in these fines. This paper describes the new circuits commissioned in July 2016 built to improve carbon fines collection, incinerate the carbon fines and leach the gold in the ashes produced by incineration. These new circuits successfully demonstrate that it is possible to extract more than 94% of the gold content in the carbon fines. This is profitable for the company as it improves the overall mill recovery rate by 1.0% to 1.5% and significantly decreases gold inventory build-up on site.INTRODUCTION The activated carbon used in the carbon-in-leach (CIL) to absorb gold is subject to breakage. This breakage can occur in the CIL tanks, the stripping circuit, the regeneration process or anywhere throughout the pumping and handling processes of carbon through the circuit. Fine carbon particles are invariably created and, because of their small size, present a large specific surface which favors gold absorption (Hilsher et al., 2014). At the very beginning of operations at Essakane, the carbon fines were recovered by means of a thickener and a filter press, but the circuit was undersized and inefficient. Subsequently, a decantation basin was used to settle the fines before the thickener. The settled fines were shovelled from the basin into bags. All these bags were stored in the backyard of the plant. The average tonnage of carbon fines recovered monthly was 23.5 tons with a gold grade at 1938 g/t."

Jan 1, 2017

Mirador - Overview ? Located in Andean foothills of SE Ecuador ? Copper-gold porphyry hosted by calc-alkaline Late Jurassic granitic and porphyritic rocks ? 438 MT of 0.61% Cu and 0.19 g/t Au measured and indicated resources (at 0.4% Cu cut-off) ? Additional inferred resources of 235 MT of 0.52% Cu and 0.17 g/t Au ? Initial 25,000 tonnes/day production, expanding to 50,000 in year 6 320 MT of 0.62% Cu, 0.2 g/t Au ore mined at an average 1.4:1 strip ratio over a 21 year mine-life

May 1, 2006

By D. W. MacFarlane

In the formation of Oil and Gas Producing Units lawyer& and engineers are interdependent members of the same team. Management is, there-fore, entitled to expect no less than a total cooperative effort from the members of these professions. The petroleum and natural gas lawyer must diligently inform himself on the implications of engineering evidence. Otherwise he can be of little assistance to his engineering witness in a thorough, systematic and convincing presentation of his technical evidence. Conversely, the engineer must appreciate the concern of counsel that quasijudical hearings, whether technical or otherwise, be con-ducted in such a manner as to pre-serve some semblance of organized judicial procedures in the adjudication of property rights. The principal problems in unitization are the participation formula and the adjustment of investment in unit facilities. The equating of oil to gas, the effect of unit infill drilling, the relative values of producing zones and well productivity have •been controversial factors in several Saskatchewan units to date. Perhaps the most perplexing of these has been well productivity. While preserving current income, it may also preserve an ability to drain adjacent tracts plus an inequitable sharing of .reserves properly attributable to secondary recovery operations. However, inequity may also result in depriving an operator of the benefits accruing to him under competitive operations by virtue of his favourable reservoir position or his use of advanced production techniques. The Saskatchewan Oil and Gas Conservation Act has been construed by the Department of Mineral Resources as •completely negating any benefits inherent in the rule of capture when determining equities under unit operations. Under adjustment of investment provisions, large cash flows between owners of exploited acreage should be avoided upon the creation of a unit. These provisions should not deprive any company of the benefits it may have obtained under competitive operations in producing its fair share of the reservoir at a lower net cost per barrel than its competitors. Unitization should be concerned with physical conservation rather than in equalizing production costs as between operators.

Jan 1, 1960

By Alfred E. Pugsley

PAYMASTER CONSOLIDATED MINES, LIMITED, began an investigation into the economy and use of detachable bit drill-steel in June, 1937. This investigation has continued to the present time, and was made necessary by transportation and distribution difficulties that had arisen through the use of standard steel in three widely separated mine areas serviced by a central steel-sharpening shop. Detachable bit drill-steel performance was first studied in the workings of No. 2 mine, where the rock being drilled was composed mainly of porphyry or tourmaline, and where standard drill-steel transportation costs had been excessive. The results obtained in this early work definitely established the economy of detachable bit drill-steel at No. 2 mine. This conclusion was reached when the 're-grind' system of re-sharpening dulled detachable bits was 1n use. Preliminary observations on the performance of detachable bit drill-steel in the quartz-carbonate veins of No. S and No. 6 mines gave encouraging results, and warranted a large-scale investigation under practical mining conditions. All drilling operations were gradually changed over to use of detachable bit drill-steel. This change was completed by February, 1938.

Jan 1, 1939

By J. E. Gebhardt, D. McBride, M. Cross

Heap leach processes can encounter diverse flow conditions, such as infiltration into dry ore material, drainage, perched water tables and heterogeneous materials, leading to large variations in permeability and the creation of preferential flow pathways. Climate and meteorological conditions, such as precipitation, evaporation, and temperature, can also have a significant effect on the hydrodynamics of the heap. Nonuniform and adverse flow behavior within the heap contributes to reducing the leaching efficiency of the heap leading to lower metal recoveries. The variability of flow within the heap can result in solute transport problems, which limit the leach reaction kinetics. Therefore, understanding the flow and transport phenomena within the heap is critical in its design and optimization. A comprehensive heap leach model, developed within a computational fluid dynamics (CFD) framework, employs robust algorithms to solve diverse variably saturated flow conditions. The model allows for a wide array of complex thermo-fluid physics to be represented and captures suites of very complex reactions that are closely coupled with thermal conditions and key microbial populations. Employing a three-dimensional heterogeneous ‘test’ heap, a number of flow conditions are investigated and the sensitivity of metal recovery is discussed.

Jan 1, 2014

By Jeffrey T. McGinty, Frank M. Wheeler

Plant layout is the arrangement of equipment, process areas, departments, infrastructure, and support facilities. Plant logistics is the flow of parts, people, resources, and information throughout the production process. This chapter: outlines key factors and provides checklists to facilitate layout development; presents risk management approaches to test the logistics and functionality of alternative layouts; and uses real-world examples to illustrate effective simulation modelling to assess plant layouts.

Jan 1, 2015

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

By Robert B. Parsons

"The last edition of Tax Notes expressed concern about two proposed tax changes in Finance Minister Paul Martin's 1995 budget that could have detrimental effects on Canada's mining industry. This month, Tax Notes expands on these concerns. This article is based on a paper that the author presented at ClM '95 in HalifaxIntroductionOn a global basis, there are more investment opportunities in the mining industry today than at any other time in history. Countries in Central and South America, Eastern Europe, the CIS, Central Asia, and Asia are competing aggressively to attract investment to all sectors of their domestic mining industries. Today, the demand for investment dollars exceeds the amount of dollars that are available for investment in mining. It is not surprising, then, that the established mineral producing nations are witnessing a decline in spending on exploration and development on their home turf, and an increase in spending in developing countries. In the context of a developed country such as Canada, there are two manifestations of the problem of declining investment: (I) Foreign investors are allocating more of their capital budgets to new opportunities in developing countries; and (2) Canadian juniors and seniors are spending proportionately more abroad. This shift in global spending patterns is the source of some concern for the future of Canada's mining industry, particularly because it is widely believed that the current rate of discovery of ore reserves in this country is too low to replenish depleting reserves.""Government bashing"" has always been a popular pastime in Canada. Invariably, this pastime has focussed, at !east in part, on taxation. In view of the intense competition that Canada faces on the global mining scene, it is important that the role of taxation in the decision-making process be kept in perspective. This paper seeks to put the role of taxation into perspective."

Jan 1, 1995

By J. Aiello

"Introduction Byron Creek Collieries Limited Corbin mine is located in southeastern British Columbia approximately 180 air kilometres southwest of Calgary (Fig. I), twenty four kilometres south of Highway No. 3 via a newly constructed provincial road (Fig. 2). The development of the area began July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J. Roberts first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co., after acquiring 6,000 hectares of land in the area, began to develop a mine. Mr. Roberts was responsible for the construction of the 22-kilometre rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production. The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3) and production from 1908 to 1930 inclusive totalled 2,120,800 tonnes. This production was allocated to the mines as follows:"

Jan 1, 1985

By Andrzej Luszczkiewicz, Magdalena Duchnowska, KGHM Polska Miedz S. A., Witold Pawlos, Jan Drzymala, Alicja Bakalarz, Przemyslaw B. Kowalczuk

Numerous data in the literature confirm that the chemical composition and consumption of grinding media influence electrochemical properties of flotation suspension as well as effectiveness and selectivity of upgrading processes. During a milling process, attrition of grinding media is observed. Depending on the susceptibility to abrasion, the grinding media influence, to a different extent, the redox potential, pH as well as flotation efficiency. As a result, different upgradeability of sulfide minerals is observed. The paper presents laboratory scale flotation results, obtained for the copper sulfide ore from Polkowice Region of KGHM Polska Miedz S.A. in Poland ground in the presence of forged steel, highchrome iron and stainless steel as the grinding media. The investigated flotation feed contained 36 g/t (ppm) of silver and 1.86 % of copper. Several flotation tests were conducted using fixed amount of frother and a mixture of sodium ethyl and isobutyl xanthates as the collector at three different doses of 75, 100 and 125 g/t. A comparison of the obtained results confirmed that the application of grinding media with different chemical compositions influenced the electrochemical properties of the suspension and recovery of silver and copper in the final concentrate. The highest values of redox potential were observed for the stainless steel as the grinding medium. Moreover, in the presence of this type of grinding media, regardless of the collector dosage, the best silver upgrading was observed. For the forged and high-chrome iron media, the recovery of silver depended on the collector dosage. It is indicated that higher levels of the redox potential, together with smaller amount of iron released from the grinding medium, improve the flotation of the silver-bearing mineral compounds from the copper sulfide ore.

Jan 1, 2016

By Chr. Krause

Within the scope the collaborative research centre 599 (Medical University of Hanover, University of Veterinary Medicine Hanover, University of Hanover) the behaviour of the degradation of magnesium materials as implants are investigated by using animal experiments (rabbits). Thus extruded cylindrical pins from the magnesium alloys MgCa0.8%, WE43 and LAE 442 were implanted intramedullary in the tibiadiaphyses. The implantation duration was 3 and 6 month. After the explantation 3 point bending tests were carried out to investigate the possible changes of the mechanical properties. Clearly changes in dependence of the implantation duration could be determined. The three magnesium alloys show a decrease of the mechanical resistance with an increasing implantation time. To evaluate the degradation process, wich is the reason for the changes, micrographs and element analyses (EDX) have been accomplished after the 3 point bending tests. The micrographs show for all used magnesium alloys corroded surfaces but no preferred corrosion on the grain boundarys. The element analyses show beside a layer which is rich in calcium and phosphorus an agglomeration of rare earth elements in this layer. With these results a using of magnesium alloys as a material for implants can be announced.

Jan 1, 2006

By D. A. Wheeler, Rémi Tremblay

"INTRODUCTIONDuring the last few years, through Column Flotation Company of Canada ltd, the Centre de Recherches minérales has worked on the column flotation of coal, phosphate, feldspar, talc, graphite, copper, lead-zinc and diamond ores. The operating companies and prospective deposits were located in Canada and in other countries. Since these projects were financed by the concerned mining companies, all results remain confidential unless we obtain permission to publish. Three companies have graciously allowed us to use their information which I will describe in this text. These are the Polkowice copper mine in Poland, the North Coast Industries ltd graphite deposit and a talc company which preferred to remain anonymous. I will also describe our 2 inch column which was used for all tests. Data is also given on how to scale-up the 2 inch column to industrial size.Figure 1 presents a schematic of a flotation column. Feed, at a controlled rate and pulp density, enters at about 1/4 of the height of the column from the top. A controlled rate of air is bubbled into the bottom of column through a fine-holed sparger. The column volume between the feed point and the top of the sparger is called the recovery zone. Tailings, at a controlled rate, always slightly greater than the feed rate, discharges from the bottom of the column. This difference in feed and tailings flowrates is called the bias. The floated mineral is carried through the recovery zone on air bubbles which rise into the cleaning zone which is that column volume between the feed point and the overflow at the top. As the bubbles rise in this zone they are washed of gangue material by wash water which enters over the top of the froth layer. The froth layer is maintained at a given depth during flotation but this depth will depend on the froth cleanliness, for quite a bit of cleaning by wash water is accomplished in this layer."

Jan 1, 1988