Search Documents

By E. C. Goodhue, R. D. Coleman, I. E. Puddington, A. F. Sirianni

Iron ore samples containing apatite are fractionated to acceptable products by spherical agglomeration methods. The phosphorus is upgraded by a factor of 10 at an elevated pH. High-grade iron products are obtained in good yields from the tailings in a second step of the operation. The grade of the phosphorus separated appears to reach a maximum at about pH = 10; recovery of iron decreases below about pH = 4. Both the recovery and grade of iron are found to be reduced sharply above about pH = 8.

Jan 1, 1968

By Takayuki Takasugi, Naoya Masahashi, Yasuyuki Kaneno, Satoshi Semboshi, Yusuke Kadoi

Cu–Ti alloy wires doped with and without a small amount of Ni were fabricated by over-aging and using intense drawing procedures. For both the Cu–Ti alloys with and without Ni doping, the over- aged microstructure was occupied fully with a coarse lamella of Cu solid solution and β-Cu4Ti plates precipitated discontinuously by grain boundary reactions. The full-lamellar microstructure was developed much more rapidly by aging in multi steps at 873 K to 723 K rather than by isothermal aging at 723 K. Ni doping in Cu-Ti alloy was also effective to accelerate the formation of the lamellar microstructure. When drawing the over-aged alloy with inferior hardness but superior electrical conductivity, the strength increased steadily and eventually exceeded that for the wires drawn from the peak-aged alloy. In addition, the electrical conductivity of the wires drawn from the over-aged alloy was always much greater than that from the peak-aged alloy. Eventually, the procedure of over-aging, followed by intense drawing, could enhance both the strength and electrical conductivity of Cu-Ti alloys, whichever they contain a small amount of Ni or not, rather than the conventional peak-aging and drawing process. INTRODUCTION Cu-based alloy wires, which have an excellent combination of strength and electrical conductivity, have attracted extensive attention for highly mechanically stressed electrical devices, such as conductive lead wires and wires in suspension springs. Cu-Be alloys are widely used for such electrical components owing to their combination of strength and electrical conductivity among industrial Cu-based alloys. However, since beryllium is potentially toxic and also a rare element, substitute materials for Cu-Be alloys have been searched for several decades. Age-hardenable Cu–Ti based alloys have been proposed as candidates because their mechanical and physical properties are comparable to those of Cu-Be alloys; however, their electrical conductivity is inferior (Datta & Soffa, 1976; Soffa & Laughlin, 2004). In order to satisfy the requirement of downsizing and streamlining electrical devices, further improvement of the mechanical and electrical properties of Cu–Ti alloy wires is needed. Age-hardenable Cu–Ti alloys, which contain approximately 3 to 6 at.% Ti, are typically prepared using a solid solution treatment above 1100 K and then aging at a moderate temperature of 700 K to 800 K. It has been revealed that the microstructural events during aging progress as follows (Soffa & Laughlin, 2004): (1) compositional modulation of the parent supersaturated Cu solid solution in an initial aging stage (Laughlin & Cahn, 1975), (2) continuous nucleation and growth of fine needle-shaped precipitates of metastable β’-Cu4Ti with a tetragonal structure in a peak-aged stage, and (3) discontinuous precipitation of cellular components laminating the plates of a terminal Cu solid solution and stable β-Cu4Ti with an orthorhombic structure at the grain boundaries in an over-aging stage. It has been also accepted that the highest number density of dispersed fine β’-Cu4Ti needles should contribute to maximal strengthening. On the other hand, decease of the strength in the over-aging stage occurs due to the replacement of the fine β’- Cu4Ti needles with cellular components containing coarse β-Cu4Ti plates, while the electrical conductivity is significantly enhanced due to the depletion of solute Ti in the Cu matrix. This suggests that a combination of strength and electrical conductivity for age-hardenable Cu-Ti alloys is in a trade-off relationship, and that innovative improvement of both properties might be limited to tuning the aging conditions.

Jan 1, 2019

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the 'bed-rock belt' and the other the 'drift belt'.

Jan 1, 1945

By Thomas J. Ferree

"IntroductionThe objective of this chapter is to provide important criteria relating to the operation and maintenance of spiral concentrators and Reichert cones, so that optimum performance can be achieved and maintained in a mill circuit. Little space will be devoted to the theory of the forces of separation or the technical details of the devices, as that in(ormation is available from other sources. The discussions in this chapter will be presented in a manner that should be interesting and useful to anyone who may be exposed to these methods of gravity separation. It is most important for the reader to understand that each application of the equipment should be considered on its own merit, as no two suites of minerals respond exactly alike in mineral processing circuits. The information herein should be useful as a guide toward increasing the metallurgical efficiency of the processes, irrespective of the type of minerals being concentrated.It is highly recommended that certain tools be made available to the personnel responsible for metallurgical performance of the spirals and cones; these include a set of standard type laboratory screens, a medium quality petrographic microscope, and a vanning plaque or gold pan. These devices, when used in conjunction with a basic understanding of the mill circuit, provide immediate knowledge on the characteristics of any sample in the mill circuit. The information gained by visual evaluation of sized fractions of products can solve many of the basic problems of mineral beneficiation, and at the same time increase the interest of the non-technical personnel associated with the plant operation. There are many problems associated with obtaining satisfactory performance from a mill operation. Many of the problems have to be solved using a technical approach. Some of the problems, however, can be solved with practical knowledge and common sense. It is hoped this chapter can provide a guide to both techniques."

Jan 1, 1989

By W. Noel O?Brien

Introduction Since 1930 numerous improvements have been made in equipment designed for the mechanical removal of broken ore in underground mining operations. New applications of mechanical equipment, as? well as improvements and adaptations of well established systems, are being made continually. It is the purpose of this paper to discuss present-day equipment for the removal or transfer of broken ore by means of a powered hoist and scraper arrangement. The terms used throughout the paper are those commonly employed in the trade literature and by mining men. The terms slusher hoist, hoist, and scraper hoist are used inter-changeably to mean a machine, powered by compressed air or electricity, with drums for the winding of wire rope. The tail rope, also known as the pull-back rope or return rope, drags the empty scraper toward the tail-sheave, that is, back to the loading point. No attempt is made to cover the entire field of application of scraping methods. Rather it is the? writer's desire to emphasize the fundamental principles of scraping practice and design and to relate them to some modern applications. The available literature on scraping practice has been freely used. together with personal observation and information and advice of practising engineers and representatives of companies manufacturing slushing equipment.

Jan 1, 1951

By John Convey

This short paper deals with the subject of research and its relation to productivity. All who have stopped to even think about industrial re-search and its impact on the nation-al economy take for granted that research and development are pre-requisite to increased productivity. It is another matter, however, to identify and properly evaluate the many factors entering into the relationship between the two. Some studies are currently underway in the United States on the subject, but, so far, nothing much in the way of conclusive data has come to light. In Canada, we have not yet even produced any statistical figures on national productivity, although work is now being done on this subject and information will soon be available. The usefulness of being able to measure the benefits of investment in re-search and development in terms of industrial growth or productivity need not be laboured for the benefit of those interested in research management.

Jan 1, 1964

By W. T. Robson

ONE of the problems encountered in any mine is the effect of increasing pressure manifested by increasing depth. Although the depth at which excessive pressure assumes serious proportion, and the manner in which it appears in underground workings, are influenced by a variety of factors, nevertheless the difficulty is present in all mines and its gravity increases with increasing depth. In the Kirkland Lake camp, as far back as seven years ago, mining had proceeded to depths sufficient to result in the formation of pressure great enough to cause violent disruption of masses of rock. It is proposed in this paper to deal with the effect of pressure caused by mining as observed at Lake Shore Mines, and to describe some of the methods which have been adopted to counteract it. There are many contributing factors in a study of the problem, and results vary widely in individual mines and in different localities. One feature common to all, however, is that there is ground subsidence, evidenced either by a gradual settling accompanied by crushing and shearing of the ore and wall-rocks, or the disruption of the ground surrounding the periphery of an excavation may take place suddenly, attended by more or less violent shattering of the rocks. Such violent failure of a mass of rock has been designated by the term rock-burst. The history of rock-bursts extends over a great number of years. They have occurred in some form or other in practically ali places where mining operations, at all but very shallow depths, have been carried out. Since the theoretical aspects of the subject have been dealt 'with at great length by capable and experienced writers (1), the present paper will give only a brief résumé of the theories propounded by those engaged in deep mining operations in various parts of the world.

Jan 1, 1940

By L. Don Leet

Abstract Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. The nature and magnitude of vibrations from various sources have been investigated and certain applications of the knowledge thus gained have been made. Vibrations from blasting have been measured on special equipment over a range from an electric blasting cap at a few feet, through the largest quarry shot in history to date ( 1,-362,985 lb.), to the first atomic bomb, in uew Mexico on July 16th, 1945. Laws relating amount of explosive to amount of vibration at different distances have been developed and tested. Special studies have been made of the effects of vibrations on buildings, particularly from the standpoint of possible structural damage. Recorded vibrations are used to study the effects of modern short-period delay shooting. It ?has been found that short-period delay firing is extremely effective in reducing vibrations under the right conditions, but with certain limitations. In quarry shooting, there appears to be a minimum number of holes below which vibrations are not appreciably reduced by short-period delay firing. In several instances this minimum has been near 7. Vibrations in the ground from rock bursts and the effects of mining in stresesd ground have been studied both underground and on the surface in a search for a rock burst warning system. Introduction Earthborne vibrations from blasting and other sources, including rock bursts, can now be recorded effectively. Analyses of blasting records have been yielding increasing funds of information of practical as well as theoretical interest. The nature and magnitude of the vibrations have been investigated with special reference to their effects on structures.

Jan 1, 1951

"In numerous meetings, conferences and discussions over the past year, the Conference Board of Canada has been impressed with the efforts of Canadian organizations to improve their competitive position. The attempt should be made to try to pull together and synthesize what has been heard. The topic of this paper, however, is even more daunting. The task is not only to analyze and discuss what is happening now, but also to look into the future—to the year 2000.The future seems to have an endless capacity for surprises, often unpleasant. This is one of the lessons learned in the twentieth century, particularly over the last 15 or so years.This paper covers three areas of managing in a changing com¬petitive environment: (1) the major global and domestic trends that will influence the ways in which Canadian organizations are managed (2) how Canadian companies are responding or will need to respond to these trends; and (3) the implications of the preced¬ing for human resource management and human resource professionals."

Jan 1, 1991

By S. J. Cook

Copper, a world commodity, and the first metal used by man, played a great part in the beginnings of modern civilization, which rests so dependently on the utilization of metals. Then, long after the close of the so-called 'bronze age,' when iron and steel had attained great prominence as the world's most important metals, the practical application of electricity to industry and commerce, for the improvement of every phase of man's multitudinous activities, gave a new impetus to the production of copper. Improved metallurgical practice made it possible to work low-grade properties at a profit. Research disclosed many new uses for copper. The metal, now produced from the mines of the world in the proportion of about one pound to every 50 tons of pig iron, has attained an importance which rivals that of iron and steel in the commerce and daily life of every nation. New fields of copper-bearing ore have been discovered in Canada in recent years. Established mines in the United States and Chile are producing on a great scale. Africa looms up as one of the great question marks in the future of copper. Whereas, a few years ago, the end of the world?s resources was predicted as being in sight, the evidence now available seems to show that the copper production of the world is likely not only to continue, but to increase for a long time yet to come. Canada's future in copper is a great subject; in the present paper only a few of the most outstanding factors affecting Canada's destiny in this large field may be noted, but if consideration of the points raised herein serves to focus attention on the magnificent possibilities of Canada as a producer of copper, the preparation of the paper will be more than justified.

Jan 1, 1928

By H. Langlois

"Included in the Mines Gaspe mining complex located at Murdochville, Quebec, is a copper smelter which comprises a reverberator furnace, two Peirce-Smith converters, an anode furance, and a sulphuric acid plant.The 50% smelter capacity available is supple mentedby custom concentrates for treatment. As these concentrates can be varied and extremely complex many modifications and improvements have been brought about to optimize and make the process more flexible since its inauguration in 1955.IntroductionThe copper smelter of the Mines Gaspe mining complex is located in Murdochville, a small municipality in the heart of the Gaspe peninsula, 90 km northwest of the town of Gaspe .This metallurgical installation has a daily smelting capacity of 650 tonnes of concentrate and an output of 250 tonnes of copper and 900 tonnes of sulphuric acid. Its main components are: a reverberatory furnace, two Peirce-Smith converters, one rotary anode furnace and one acid plant. The gases, which are produced by the converters, are treated at the acid plant then combined with gases from the reverberatory furnace before being vented through a 152 metre high stack .From the beginning of its operation until the present day (1991), the smelter has treated 7 million tonnes of concentrate and 100 thousand tonnes of scrap for a production of 1.8 million tonnes of copper and 2.2 million tonnes of sulphuric acid."

Jan 1, 1993

By Suzanne Paradis

Geographic distribution ? Deposit economics ? Temporal distribution ? Tectonic settings ? Basin architecture ? Morphology ? Ore-fluid chemistries Key exploration criteria

May 1, 2006

By Georgia J. Lysay

Kemess South Mine ended operations in March 2011. Final reclamation works began during operations in 2008 in anticipation of closure. The focus of reclamation during mine operations was on the inactive areas of the tailings dam, waste rock dumps, and expended borrow areas. The general reclamation strategy for the Kemess Mine site marries long-term erosion control with successional reclamation principles. For disturbed areas, this requires application of growth media, proper preparation of surfaces, and introduction of native pioneer plant species to initiate successional processes of recovery. Tailings are retained behind an earthfill dam of approximately 140 m in height, with a crest length in excess of 1 km. Reclamation activities at the dam have included placement of growth media, specialized surface preparation and construction of diversion ditches. The final closure spillway is currently being constructed, with completion scheduled for summer 2011. The two main waste rock dumps contain segregated non-acid generating (NAG) waste rock and potentially acid generating (PAG) waste rock. Resloping of the NAG dump for long-term stability commenced in 2009, followed by placement of growth media and ground preparation. The PAG waste rock will be fully relocated into the expended open pit for final, permanent subaqueous disposal.

May 1, 2011

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By John B. Phillips

The mine is entered by a central vertical shaft, strongly timbered, and containing two compartments-one for the passenger cage, the other for the large skips bringing the ore to the surface. A man-way, for emergencies, is also provided, parallel to the shaft. The cage is a single-deck steel box, carrying about thirty persons; by means of arrangements above and below, it can also hoist and lower materials needed in the workings. Levels are run at intervals of 100 feet. In special cases, where the ore conditions warrant, sub-levels are operated, such as those at 1,113 feet and 1,123 feet (Fig. 7), which are connected by winzes with the 11 th level. One of these was pushed for 40 feet, and then abandoned because it was unprofitable to take up ore of the grade encountered. The ore between levels is removed by stoping. The drifts follow the course of the veins as much as possible, with numerous cross-cuts. Winzes, raises, connections, etc., are blasted out where needed. The main drifts are at least 8 ft. high by about 9 ft. wide. All former narrow drifts had to be widened sorne time ago, by ruling of the Ontario Department of Mines, to lessen the danger of accidents with cars in the small passages. Accurate plans of the under-ground workings are kept in the office, and extensive surveying is always being done underground to keep the maps up to date, measure the cubical contents of stopes, and so forth. Timber is extensively used in the construction of supports and chutes, and in the sinking of the shaft. Steel and concrete are too expensive to compete with timber, which 1s abundant in such sections as have escaped forest tires.

Jan 1, 1926

By Jason Mewis

Do you have it figured out? ? If so, I want to network with you! ? There?s a lot to learn as an industry The more we share the better we?ll all become at dealing with this subject If you don?t have it figured out ? You?re among the majority in the in0dustry ? Project Risk is a broad and complex issue that is dealt with through many processes ? And it?s not intuitive either ? And you don?t want to confuse one process with Another

Nov 1, 2011

By Robin Perry, Claude Bazin

"Discrete transfer functions which use the grinding circuit feed tonnage to predict mass flowrates at reagent addition points in a flotation circuit were calibrated using a dynamic grinding/flotation circuit simulator. Predicted mass flow values are multiplied by reagent addition ratios to obtain actual reagent flow. The transfer functions are currently integrated into the distributed control system of Les Mines Selbaie.IntroductionThe development of adequate tools for the control of flotation processes is a continuous challenge. Since the early 1970s there have been numerous publications dealing with practical aspect of control of flotation processes. Most plants use a combination of feedback and feedforward controls to reduce the effect of the following flotation process disturbances (McKee, 1991):• changes in throughput;• changes in feed grade;• changes in particle floatability (size, liberation, surface oxidation ... ); and • deliberate changes of setpoint;Feedforward control manipulates variables such as reagent and/or air flow rate to attenuate the effect of disturbances such as changes of feed rate and mineral content. The feed forward strategy is driven by measurements of these disturbances. Feedback control is used to maintain process variables to targeted set-points of concentrate or tails grades. The feedback control action is driven by deviation from the set-point, caused by a deliberate change of set-point or disturbances.This paper proposes a method to improve feed forward control schemes by the addition of a simple model for solids transportation. The feedforward strategy considered in this paper is the ratio type, in which the manipulated variable is changed according to a predefmed ratio between this variable and the measured disturbance. A typical example is the ratio of the reagent addition to mass flow of ore.The paper reviews the state of the art in feed forward control strategy applied to flotation processes and describes the method used for predicting mass flow rates. The last section shows an application of the method in the Les Mines Selbaie flotation circuit."

Jan 1, 1994

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By J. E. Rehder

IN A DISCUSSION of use of any material of ?construction in the mining industry, two points of view must 'be kept in mind - that of the producer or manufacturer of mining and metallurgical equipment, and that of the maintenance and operating staff of the mining plant. In the first case, the choice of material of construction is up to the manufacturer and the user of the equipment has little direct say in the matter. However, if materials are badly chosen and the equipment does not function properly, wears out rapidly, or costs too much, repeat orders ?will likely go to a different manufacturer, so that, in the end, the consumer or mine operator does have the final voice. In the case of materials for maintenance work and plant operations, however, .the mill personnel have direct control over purchases and it is then that a well-balanced knowledge of materials, their properties, and their costs, can be directly useful. With all materials of construction, the final criterion is unit cost versus service performance, so that the lowest possible total operational cost will be obtained. Sometimes this means using the cheapest material available, sometimes the most expensive, but in any case careful analysis of service performance, replacement cost, and material cost is essential to determining the material that produces lowest total cost.

Jan 1, 1956

By A. G. Roach

IT IS generally stated that the gold ores of Nova Scotia are free-milling, and for the most part this is true. However, there is a certain proportion of the gold finely disseminated throughout the sulphides, notably arsenopyrite, and this gold is definitely not recoverable as 'free-milling' gold by amalgamation. The proportion of free-milling gold to total gold seems to vary widely in different localities in the Province and is lowest in deposits of the fissure-vein type. The problem of recovery of these relatively recalcitrant values is usually one of economics, in some plac.es a simple gravity concentrate being of such low tenor that its extraction and subsequent disposal will not bear the costs involved. In other cases, such a high percentage of values escapes from the mortars and plates that concentration is definitely indicated. The size of the mining operation is also an important factor. In the large majority of cases, however, some concentrating step is warranted, even if the resulting concentrate is stock-piled until sufficient has accumulated to justify further treatment.

Jan 1, 1940