Search Documents

By W. L. Brown

"The Normetal mine is about 7 miles east of the Ontario-Quebec boundary, and 13 miles north of the town of Dupuy on the Canadian National railway. The mine workings are largely on lots 44 and 45 in the south half of range 10, Desmeloizes township.The surface outcrop is reported to have been discovered by a trapper previous to 1925, but the details are obscure. The property was originally owned by the Canadian Exploration Company of Amos, Quebec, and was later transferred to Abana Mines, Limited. The latter Company carried out underground work from two shafts down to the 550-foot level. The property was acquired by Normetal Mining Corporation in 1931 and was reopened in 1933, when development work was carried down to the 800-foot level. The mine was closed down in 1935 because metal prices did not justify production at that time. It was reopened early in 1937 and milling commenced in September of that year. To the end of 1945, a total of 1,497,- 169 tons of ore was milled from which was produced 184,533 tons of copper concentrates containing 84,738,368 lb. copper, 2,744,100 oz. silver, 26,230 oz. gold, and 153,524 tons of zinc concentrates containing 163,752,433 lb . zinc."

Jan 1, 1954

By G. Grassmück

The question of whether the air curtain principle could be used under conditions prevailing in Canadian metal mines was investigated. A vertical, portable BERRY air curtain was tested, at first in a wind tunnel built at Ecole Polytechnique at full scale (8-by 8-ft cross section) to simulate a drift and its lateral connections, and then in the haulage ways of a metal mine under actual conditions. The results permit us to predict under what conditions this type of air curtain is capable of acting as an air stopping or flow regulator and how it could be further developed.

Jan 1, 1969

By C. M. Anson

Introduction The prosperity of any country today is dependent upon the efficiency and growth of its primary steel industry. The ?march of the United States of America to its present commanding position in world affairs parallels the growth of its steel industry. The remarkable growth of that industry was possible only because bountiful providence endowed that country with adequate supplies of the raw materials necessary for steel making -coal and iron ore. If we accept this hypothesis, and surely we must, then to what extent can we envisage the future of our own country? This symposium deals with the most important of the raw materials required for steel making -iron ore. If we are blessed with a bountiful supply of iron ore, then surely a glorious future awaits only our taking advantage of that blessing. It is becoming increasingly evident that Canada has immense iron ore deposits. It is my privilege to make you acquainted with one of these, one that can only be classified as among the more important ore reserves in the world. I refer to the Wabana ore deposits in Newfoundland. Location These deposits lie under the floor? of Conception bay, off the east coast of Newfoundland. They consist of a series of beds which outcropped for a distance of about three miles on the northeastern shore of Bell Island, dipping at approximately 8° toward the northwest. This three-mile outcrop is the only key to the occurrence.

Jan 1, 1951

By Lawrence Devon Smith

"This paper examines the impact of the various assumptions that go into an economic evaluation, and shows how these can be combined to show an exciting result that may not really exist. An example of an embellished case (the kind that one frequently sees when projects are being promoted) is developed and the cumulative impact is analysed to show the actual project underneath. The paper also points out some areas to watch for overly optimistic assumptions such as prices, inflation, and debt. The concept of a ""bare bones"" base case is proposed (constant metal prices, constant dollars, no inflation, no debt, no interest, on a project basis, after tax) as a common reference point.As well, the discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.INTRODUCTIONOften, the first time that all of the technical and economic data for a mineral project comes together in one place is when the economic evaluation is developed. This typically happens when work on the project has progressed to a sufficient level of detail that the effort to produce a year-by-year cash flow is justified, usually at the pre-feasibility or feasibility study stage. The data involved will include:• production; tonnes waste and ore mined, ore grade, mining recovery, metallurgical recovery, metal sold• revenue; metal price, smelting & refining charges, marketing costs• operating Costs; mining, milling, administration, fees, royalties• capital Costs; exploration, development, construction, indirect costs (engineering, management), contingencies, start-up, inventories, working capital, replacement and sustaining capital, closure costs• taxes and royalties• exclusions; depreciation (this is not a cash item), sunk costs (only costs going forward)."

Jan 1, 2003

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as 'soapstone'. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By J. H. Walsh

IN THE DEVELOPMENT of procedures for the separation of minerals, the choice of reagents for flotation is frequently determined by the extent to which a given mineral is wettable by water. Measurements of the contact angle of an air bubble on wet mineral surfaces are often used in the laboratory to estimate the wettability of the surface. For the results of these measurements to be reproducible, the surface of the mineral must be polished to a mirror-like smoothness and must be free from oily contamination. Elaborate procedures for preparing mineral surfaces have been developed by Wark ( 1) and Taggart (2), and these procedures have been generally accepted as adequate for their purpose. The polishing techniques, how-ever, have certain inherent disadvantages which make it impossible to assess the effects of polishing, entrained abrasive, and adsorbed gases on the wettability of the mineral surface.

Jan 1, 1957

By J. E. Dutrizac

The dissolution of low-iron sphalerite, (Zn,Fe)S containing 0.08% Fe, in ferric sulphate-sulphuric acid media was investigated using closely sized fractions of crushed sphalerite crystals and sintered disks made from the crushed crystals. Linear kinetics are observed, and the predominant reaction products are ZnSO4, FeSO4 and elemental sulphur. The leaching rate increases systematically with increasing temperature, and the calculated apparent activation energy is 56 kJ/mol for the sized sphalerite and 54 kJ/mol for the sintered disks. The relatively high apparent activation energy suggests that the rate is chemically controlled, a conclusion supported by the insensitivity of the rate to the disk rotation speed. The rate increases as the 0.22 power of the Fe(SO4)1.5 concentration, and as the 0.22 power of the H2SO4 concentration. However, in the absence of ferric ions, the rate increases more significantly with increasing H2SO4 concentrations, and relatively rapid rates are observed in solutions containing >0.5 M H2SO4. In 0.1 M Fe(SO4)1.5-0.3 M H2SO4 media, the measured rate decreases with increasing sulphate concentrations, added as Li2SO4. The rate of dissolution of low-iron sphalerite is promoted by dissolved copper concentrations as high as 800 mg/L. In contrast, dissolved silver, even in the 0-2 mg/L concentration range, significantly retards the dissolution of the low-iron sphalerite.

Jan 1, 2008

By P. B. Demarsh

"Location: - Mine village of Perron, 11 miles east of Val d’Or in northwestern Quebec.Life; - Started production 1932, ceased 1951.Ore: - Flat lying quartz tourmaline veins within granodiorite. Gold values related to coarse segregations of pyrite. Specific gravity 2. 80.Capacity: - 30 tons 1932-35; 125 tons 1935-37; 350 tons 1937-51.Assay: - Heads 0.21 to 0.34 oz. per ton. Grade obtained by mining 600 tons daily, sorting belt reject 250 tons, balance to milling; tailings loss 0.003 to 0.005 oz. per ton; extraction 9 8. 5%.Grind: - 70% minus 200 mesh. Detention time 26 hours.Treatment: - Cyanidation process.Reagents: - Per ton, aero cyanide (NaCn) 0.36; unslaked lump lime 1.50; zinc 0. 03; lead acetate 0. 006; steel consumption 2. 50.Water: - Equal mixture of swamp creek water and underground seepage.Cost: - Per ton, sorting and crushing 0.21; grinding 0.31; cyanidation 0.11; filtration 0.05; precipitation 0.02; miscellaneous 0.22; total 0.92.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - 95% Maritime and European, balance Quebec and Ontario.Tailings: - Absorbed over large swampy area on barren mining claims.Personnel: - 1 7 men including supervision.Flow sheet: - Canadian Mining Manual 1947"

Jan 1, 1966

By Rodnei Graça, Jorge Silva Bettencourt, Lena Virgínia Soares Monteiro, Baruch Spiro, Tolentino Flávio De Oliveira

Abstract - The Vazante Mine is located in the Vazante District, the largest zinc district in Brazil. The Vazante deposit consists dominantly of an unusual willemitic ore. Small sulfide bodies are tectonically imbricated with the willemitic ore, within the Vazante shear zone. Structural styles of deformation and petrographic and isotopic evidence indicate that willemitic mineralization and deformation occurred synchronously during the Neo-Proterozoic. Various generations of hydrothermal veins and hydraulic breccias may pre-date, accompany and overprint the mineralization. Ore-formation temperatures are deduced from stable isotope geothermometry and mineral chemistry of both sulfide bodies and willemitic ore. Temperatures during the main stage of mineralization range from 206°C to 294°C (willemitic ore) and 317°C (sulfides), and reflect the prevailing metamorphic conditions within the shear zone. The fluid from which the gangue minerals of the sulfide bodies precipitated (at 250°C) had an oxygen isotopic average value of ?18O = +19.4‰. This value appears to reflect the interaction of metamorphic fluid with the carbonate rocks of the Vazante formation. At 250°C, the fluid in equilibrium with the vein mineral phases and willemitic ore assemblage exhibits a uniform oxygen isotopic composition, with an average value of ?18O = +11.5‰. The positive linear covariance of ?18O and ?13C ratios of the carbonates is most likely due to the mixing of metamorphic and meteoric fluids. The ?34S values of sulfides indicate a direct crustal origin for the sulfur. It is suggested that the sulfur is largely derived from pre-existing sulfide bodies and has been transported by metamorphic fluids. The willemitic ore may have originated from the precipitation of metal in sulfur- poor fluids under oxidized conditions, within the Vazante shear zone.

Jan 1, 1999

By J. J. Denny

IN a preliminary paper (1) it was shown that the addition of small quantities of metallic aluminium powder almost completely inhibited the solubility of siliceous material in the beaker. Six rabbits exposed to quartz dust for six months all showed well developed silicosis. Seven rabbits exposed to quartz dust plus 1 per cent metallic aluminium powder for the same period did not develop silicosis. At that time, we were not in a position to state either the manner in which metallic aluminium reduced the solubility of siliceous material, or, from the animal experiments, whether the aluminium was acting locally or systemically, or for what period after the cessation of dusting it would continue to act. This paper reports the further progress of this investigation. CHEMICAL EXPERIMENTATION The technical details pertaining to the various substances used in the experiments are given in an appendix which is on deposit with the American Documentation Institute, Washington, D.C. For lack of space, it is not printed here. The term 'solubility' is used to indicate the concentration of silica in the solution under the conditions as noted, determined colorimetrically (2), and expressed as parts per million (p.p.m.). The term 'reduction in solubility' indicates the difference between the solubility of the .silica in the presence of the aluminium powder and its solubility in the absence of aluminium powder. It will be noted that the solubility figures for different samples of quartz with no added aluminium vary considerably. The figures do not refer to an equilibrium solubility of silica but to the actual amount of silica dissolved from a given sample in a given time at a given temperature. In view of the fact that quartz dissolves extremely slowly, it is evident that the actual figures in any case will depend upon the surface exposed, i.e., fineness of grinding of the different samples.

Jan 1, 1939

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By D. W. Tully

Sedimentary and volcanic rocks of the Timiskaming series trend west-ward across the property of the Upper Canada mine, forming part of the north limb of a regional syncline which is truncated on the south by the Larder Lake fault zone. A wide zone of schistosity strikes east-west through the sediments and volcanics. The central portion of this zone is occupied by a system of narrow gouge-filled fractures in highly altered rocks, mainly tuff, trachyte, trachyte porphyry and syenite porphyry. The alteration zones have developed through repeated stages of deformation and accompanying metamorphism. The initial stages were marked by carbonatization and sericitization, followed by silicification and the introduction of minor amounts of sulphide minerals. Gold was finally de-posited in relatively late fractures within silicified zones and pyrite. Repeated movements along the Up-per Canada break have offset post-ore dykes of minette and diabase, and have resulted in minor displacements within the orebodies.

Jan 1, 1963

By Nelson C. White

This paper summarizes the present state and future prospects of the potash industry, with special reference to its impact on production in Saskatchewan.

Jan 1, 1968

By L. X. Li

Coking coal producers often encounter variations in clean coal quality when mining multiseam deposits containing coals with different washability and coking properties. This paper describes how, for a single coal property, an initial clean coal specification with an ash content of 8.5% on an air-dried basis (ADB) and a free swelling index (FSI) of 5.5 can be improved to a specification with 7.5% ash content ADB and an FSI of 6. This is accomplished by sorting coal seams into two groups for processing and blending. A preliminary economic model demonstrates how this improvement enhances economic returns through a beneficial factor.

Jan 1, 2014

By G. W. Clark

"The mining of the ore bodies at Rabbit Lake has in the past been by the open pit method. This method is presently being used to develop the B-zone and will continue into the future with the development of two smaller ore bodies, the A-zone and D-zone. The Eagle Point orebody will be developed by an underground method which will provide production and employment into the next century.The ore bodies at B-zone, A-zone and D-zone are unique in that they are located under Wollaston Lake. To permit mining by the open pit method a steel-celled dyke has been constructed around the north end of the B-zone. This same dyking method will be used for the A -zone and D-zone. INTRODUCTIONMine development at Rabbit Lake commenced in 1970when a detailed engineering feasibility study established the viability of the Rabbit Lake deposit. In 1972 construction of the mill and camp site began. Construction materials were seasonally hauled to the site over a winter road until November 1973when the government of Saskatchewan completed an all-weather road to within six miles of the operation.In October 1974, stripping of the Rabbit Lake open pit began with the removal of overburden and lake bottom sediments from the previously drained Rabbit Lake. The first ore was processed by the mill in June 1975and by October the mill was producing three million pounds per year. The design capacity of five million pounds annually was first achieved in 1977 and maintained until 1981, when lower ore grades resulted in lower production rates .It was clear when mining at Rabbit Lake began that, without additional reserves, the Rabbit Lake operation had a life of less than 10 years. Exploration, therefore, continued in the immediate area in an attempt to discover additional uranium mineralization."

Jan 1, 1989

By Robert Dickson

Princess colliery is operated by Old Sydney Collieries, Limited, a direct descendant of the General Mining Association of London, England, which, in the first quarter of the nineteenth century, pioneered in coal mining in Nova Scotia. The coal worked is a 5 ft. 6 in. seam known generally through the Sydney coalfield as the Harbour seam but referred to locally as the Sydney Main. Entry is made by shafts, 680 feet deep, sunk in 1871 on a headland forming the northern entrance to Sydney harbour. From them extend the main roadways of the colliery, a distance of 700 feet to the shore line and a further distance of 14,700 feet in submarine areas to a total length of 15,400 feet. It was the first colliery in Nova Scotia designed to work submarine areas. Lateral development extends across a frontage of 16,000 feet and the submarine area from which the coal has been extracted is slightly over 6 square miles. There yet remains sufficient territory ahead of the workings to assure a future life to this colliery estimated at over 80 years at the current rate of production. In this area the seam dips at 6 to 7 per cent and face workings have reached a depth of 1,690 feet below the sea level. Until 1923 extraction of the coal was by room-and-pillar, followed by the drawing of the pillars. At that date the superincumbent strata had reached a thickness of 1,400 feet, resulting in heavy weighting on the roof and severe side pressure on the coal ribs. In combination with a soft, heaving pavement this created a set of conditions involving great difficulties and expense in keeping open places driven in the solid sufficiently long to permit recovery of the coal in the pillars by methods and equipment then available. The operator was forced to resort to extraction by longwall as the only economical method of winning the coal.

Jan 1, 1948

By T. Plikas, L. Gunnewiek

Computational fluid dynamics (CFD) modeling was used to evaluate the performance and optimize the design of a potroom ventilation system in an aluminium smelter facility. The ventilation system must ensure the inflow of fresh air to the workplace by natural draft and the removal of heat and hazardous emissions generated from the pot cell process. A full-scale, three dimensional CFD model of the potroom was developed to predict the air temperature distribution and contaminant concentrations throughout the potroom for the purpose of verifying that the industrial workplace hygiene standards will be met by the proposed ventilation system design. The modeling work was used to optimize the size of the floor gratings around the pot cell and roof ventilator, as well as determine damper settings in the roof ventilator. The effects of outside air temperature and external wind on the performance of the ventilation system was evaluated to ensure the design performs adequately in response to seasonal variations in climatological conditions.

Jan 1, 2006

By J. E. Dutrizac

Canada is currently the world's largest supplier of zinc concentrates and is also a major producer of zinc metal. This dominant position in the world's zinc market is a fairly recent circumstance and, in fact, the country's zinc industry was founded only in the early part of the twentieth century. By contrast, the American zinc industry was well established by the mid-nineteenth century, largely based on technology originally imported from the still older European practice. Initial attempts to create a viable Canadian zinc smelter were based on the traditional practice and were unsuccessful; success came only with new electrolytic technology, much of which was developed domestically. The purpose of this paper is to outline the early attempts to produce metallic zinc in Canada and to trace the gradual development of these first efforts into a viable zinc industry based on modern science and technology.

Jan 1, 1999