Search Documents

By B. Friedrich, N. Anastasijevic, S. Stopic

The extraction of nickel from Serbian and Western Australian lateritic ore by sulphuric pressure acid leaching (PAL) has been studied. The following parameters were tested: stirring rate, acid to ore ratio, reaction time, pressure and temperature. These studies were performed with ore samples from the Rudjinci, Serbia and Silcrete, Australia, both belonging to the laterite-silicate group of deposits. An increase of the reaction temperature and the stirring speed at a fixed acid/ore ratio showed a positive influence on nickel extraction. The decrease of the oxidation potential with time correlated with the increase in Fe(II) in solution and nickel extraction as the reaction went to completion for both ores. The target values of 95 % Ni extraction and 60 % Co extraction were attained in 5 min at 250°C for the Serbian silicate ore, at an agitation rate of 1500 rpm, 10 % solids, and acid/ore ratio of 0.40. Under similar conditions only 60 % Ni, but 69 % Co could be extracted from the Australian Silcrcte ore due to different mineralogy. The nickel extraction was shown follow a diffusion-controlled reaction model.

Jan 1, 2004

By M. A. Hararah, T. Neesse, M. G. Farghaly, G. Proellss, P. Kaniut, W. Rubarth

ABSTRACT: This paper presents two new options for hydrocyclone control. Volume split control using a control valve in the overflow is applied for the stabilization of separation results at changing feed conditions. Controlled water injection to the conical part of the cyclone leads to the reduction of fine particles in the underflow. Hydrocyclone monitoring in both cases is performed by optical sensors that indicate the spray angle of the underflow. Applications in mineral processing for desliming, classification in closed-circuit grinding, and dewatering are demonstrated.

Jan 1, 2011

By C. Díaz, M. Barati

Prof. Torstein Utigard's untimely death, in the spring of 2012, put an abrupt end to a meritorious career in the field of high temperature chemical process metallurgy. As an academic in the Department of Materials Science and Engineering of the University of Toronto, Torstein made solid contributions to the advancement of knowledge pertaining to production and refining of both nonferrous and light metals, and to the development of inquisitive and innovative young people in extractive metallurgy. In this profile, the authors highlight aspects of Torstein's rich personality and of his contributions to his field of expertise.

Jan 1, 2015

By William Petruk

Image analysis studies were performed on mill products from pilot-plant and laboratory tests that had been conducted to determine the effect of grinding media on the selective flotation of two zinc-lead-copper ores. It was found that, when the ores had been ground to the same degree of fineness with flint pebbles, ceramic pebbles or ore fragments (autogenous grinding) as with steel balls, there generally was increased sphalerite, chalcopyrite and galena liberation in the flotation feeds, depending on the textures of the minerals. The increased sphalerite liberation fully accounted for the improved zinc recoveries that were obtained when steel balls were replaced by either pebbles or ore fragments. The increased chalcopyrite and galena liberation accounted for part of the changed technical efficiency of concentration, but other factors, probably changes in oxidation and reduction of iron and in consumption of oxygen, also contributed.

Jan 1, 1977

By Frederik H. Kriel, John Ralston, Craig Priest

"Stream-based microfluidic solvent extraction offers a novel alternative to bulk-scale mixer-settler operations. However present maximum throughputs are restrictive and there are engineering challenges that need to be overcome before the technology is robust. This is especially the case for mineral processing, where circuits must be able to handle variable feed streams with long retention times and where maintenance should be minimized. This paper highlights research directed at investigating and evaluating these challenges for actual mineral leach solutions of metal ions. Molecular and particulate channel fouling is discussed. Most extraction systems studied to date show no effects that would preclude use of the technology. For rare earth elements (REE) with fast extraction rates, scale-up of volumetric throughput to 100 L/h using suitable arrays of channels, microfluidic chips and modules is shown to be achievable using a small contactor (approx. 2 m3) platform. This requires only 2–3 % of the typical aqueous phase inventory and residence time used in an equivalent mixer-settler. For a circuit with 100 contactors, the overall residence time would be less than 1 h, using an aqueous inventory of 40 L.INTRODUCTIONHydrometallurgy is of pivotal importance in many mineral processing circuits around the world, with liquid-liquid solvent extraction (SX) a key step in the separation of many base metals (e.g. Cu and Ni), radioisotopes, precious metals, and the ‘technology’ metals, such as rare earth elements (REEs) (Ritcey & Ashbrook, 1979). The standard equipment for SX in mineral processing is the mixer-settler, in which liquid dispersions are created, by agitation, to increase the surface-to-bulk ratio and, thus increase the mass transfer rate between the liquid phases. In stream-based microfluidic SX (microSX), these high surface-to-volume ratios are achieved by contacting microscopic streams (Ciceri, Perera, & Stevens, 2014), rather than forming small droplets, so that phase disengagement can be accelerated (essentially instantaneous via branching of the two streams of liquid at a channel junction). MicroSX is profoundly different from bulk mixer-settler SX operations and offers exciting opportunities for processing hydrometallurgy solutions (Kriel, Holzner, Grant, Ash, Woollam, Ralston, & Priest, 2015; Priest, Zhou, Klink, Sedev, & Ralston, 2012). Nonetheless, the advantages of using microfluidic environments are presently balanced by very significant challenges relating to throughput, process control, coupling of stages, flow stability, and fouling. If these challenges can be met using smart chip designs, process control and clever engineering, high-value/low-volume SX processes stand to benefit greatly."

Jan 1, 2016

By Y. Wang

Phosphates and fluorides are used as regulators for the removal of silicates from diasporic-bauxite both in direct and reverse flotation. While using dodecylamine chloride as a collector, micro-flotation studies showed that sodium hexametaphosphate has stronger depressing power on diaspore than on silicate minerals with increasing sodium hexametaphosphate concentration at pH 6.5, but sodium fluorosilicate shows poor depression on diaspore with increasing sodium fluorosilicate concentration at the same pH. Zeta potentials of diaspore and silicate minerals become more negative both in the presence of sodium hexametaphosphate and sodium fluorosilicate. Adsorption density studies indicated that the adsorption density of sodium hexametaphosphate on diaspore is much higher than that on silicate minerals at the concentration of 75 mg/L. FTIR spectroscopy studies show that sodium hexametaphosphate interacted with the Al atoms exposed on the diaspore and silicate minerals surfaces to form P?O?Al bonds through the P02 groups. It is possible that sodium fluorosilicate interacted through F- or [SiF6]2- with silicate minerals surfaces based on the analysis by AES.

Jan 1, 2006

By D. S. Campbell

THE chief factors influencing the decision to build the Big Missouri mill underground were the topography of the country and the climate. The location underground assured certain saving in the cost of operation, such as the hearing of the mill, shovelling snow, and handling ore, which, over a period of time, would offset the greater initial cost of the mill excavation and machinery installation underground, as compared with the cost of a like plant on the surface. At Gilman, Colorado, where conditions are somewhat similar, the Empire Zinc Company, at their Eagle mine, are treating their lead-zinc ore in a mill built entirely underground. Company officials made a study of this plant before proceeding with the mill at Big Missouri. LOCATION, CLIMATE, TOPOGRAPHY The Big Missouri mine is situated on the Upper Salmon river, 22 miles north of Stewart, B.C., which is at the head of Portland canal, a narrow natural channel which penetrates 100 miles inland from the coast into the Coast Range mountains. Stewart, the distributing centre for the district, is about 600 miles north of Vancouver. The Big Missouri claims lie on and down the sides of the Big Missouri ridge, which extends north and south between the Salmon River and Cascade Creek valleys. The ridge rises to an elevation of 3,600 feet, is about half a mile wide, and to the east slopes down to the Joker flats in Cascade Creek valley. The Big Missouri camp is located on the flats at elevation 2,800 (see Figure 1). Preliminary development of the property took place from this point with an adit driven under the ridge. The western side of the ridge slopes steeply down to the Salmon glacier at elevation 1,900. Ore found on the 2,850 level extended down, and, in order further to explore the ore-body, the 2,850 level was driven through to the west side of the ridge, a surface incline tramway was built, and a lower tunnel driven at elevation 2,350, five hundred feet below the original 2,850 level, from the west side of the ridge. This tunnel development avoided the necessity of sinking, which would have been costly, as the mine makes a great deal of water (see Figures 1 and 2).

Jan 1, 1938

? Élaboration de la Directive 019 (1982) ? Objectifs: ? Protection de l ?environnement ? Procédure administrative pour analyse et évaluation environnementale ? Officialisée en 1989 ? pas eu de modifications depuis ce temps Contenu de la Directive 019 ? Requête d ?autorisation ? Gestion des eaux ? Traitement des effluents ? Gestion des déchets et des résidus miniers ? Suivi environnemental Directive 019 Exigences environnementales ? Effluents miniers ? As, Cu, Ni, Pb, Zn, Fe, CN, MES, pH, toxicité aiguë ? Suivi environnemental annuel ? Effluent ? Réseau hydrographique ? Restauration

May 1, 2001

By T. L. McCall

A short description of mining practice in the Sydney coal field in general is followed by a discussion of the operations in the No. 12 colliery of the Dominion Coal Company, Limited, as being typical of the trend in operating methods obtaining throughout the field. Development of longwall mining to the present system of three walls in line is outlined, together with a summary of the cycle of operations involved in systematic operation.

Jan 1, 1944

By D. M. Aloi

In today's evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to "engage" with communities and measure the success of these engagements without a clear understanding of "how" to do this. This move, away from "Corporate" Social Responsibility (CSR) and compliance, develops more of a focus on "Community" Social Responsibility and sustainability. This shift in focus leads to the development of world-class projects that provide sustainable development for people, reduces the incidence of costly delays, and promotes good global citizenship for corporations. The process of "engaging" communities in mining project design and development leads to a stronger license to operate and sustainable development. To create this mutually beneficial relationship between communities and companies, communities must be "engaged" in the mining process as early as possible, preferably during the exploration or the concept phases. How to create this "engagement" remains elusive. How to measure the progress of this engagement is also problematic. The quantitative and qualitative metrics needed to measure both positive and negative impacts of the mining and community relationship will be discussed.

Jan 1, 2007

By L. Frost

Physical Conditions Great Britain The physical conditions in the mines investigated in Great Britain are similar to those found in the mines of the Dominion Steel and Coal Corporation, with the important difference that many of the coal seams visited were interspersed by a large number of heavy faults, making the development of a continuous face operation difficult, and in many cases the life of a unit development was exceptionally short, adding to unit cost; but in spite of these difficulties, a great deal has been accomplished in the application of mechanical loading units in a number of the mines in the areas visited. The coal-bearing measures, as in Nova Scotia, consist of shales and sandstones, and in some sections mussel bands overlie the coal seams making roof conditions difficult'. In several mines, the main roof consisted of weak shale bind, being held by a coal roof of varying thickness. This shale bind had a tendency to flow when the coal roof was broken. The floor, in some cases where cutter loaders were operated successfully, consisted of weak, flaky shales with very little resistance and a tendency to disintegrate into powder when broken. The depth of cover under which these mines were operating varied from 250 feet to 2,340 feet, with an average of 1,700 feet. The coal seams varied in height from 3 feet to 8 feet 6 inches, and the gradients from level to 33 per cent. The seams vary in hardness, but all-with the exception of one seam, the 'Morrison Busty'- presented a cutting problem similar to that found in Nova Scotia. The structure and cleavage of the coal was well defined and uniform. Some of the seams visited were gassy, ?but the temperature of the workings generally was not in excess of 70°F.

Jan 1, 1948

By Christopher Andreae

"Years before the present iron and steel works were established at Sydney, several thriving although short-lived iron work s operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron work s. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principle fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel work s dominated production for Nova Scotia and the rest of Canada.Two sites achieved prominence in the nineteenth-century Nova Scotia iron industry: Londonderry and Ferrona. Londonderry, the larger and longer-lasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2,600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace, but once the furnace was blown out in 1904, the population gradually drifted away.Early HistoryThe history of Nova Scotia's iron industry began in 1604 when Samuel Champlain became the first European to identify iron ore in the future province. Despite this early acknowledgment, iron was not smelted commercially in Nova Scotia for another two hundred years. Although primitive smelters of the period produced more iron than could be used locally, early settlers depended on imports of iron from Britain and the United States."

Jan 1, 1983

Mineral engineering is defined as those engineering activities that relate to the discovery, development and utilization of mineral resources. Using petroleum engineering as an example, it is shown that the breadth of the field to be studied is a major educational problem. Breadth of field is aggravated by the rapidity with which technological demands may change. At present, special short courses serve to update engineering education. Recent experience suggests an increased rate of change for the future. The fact that engineers have typically human needs and goals, and the fact that engineers respond to these in our free society, introduces a third class of problems. One approach to the solution of these problems is the unified engineering curriculum based on a core of subject mat-ter common to all engineering. Experience suggests that the unified curriculum is an effective method to minimize the importance of the first two problem areas presented, and shows a degree of success in handling some problems within the third area. Perhaps, for the good of all segments of society, it is best to have both career-oriented and unified curricula represented by educational institutions of high quality.

Jan 1, 1963

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

By R. F. Neider, W. R. Bain

"Expanding upon one aspect of a recent paper on ""Fluid Column Roasting at Sherbrooke Metallurgical Co. Ltd.,"" the present paper deals with the operation of the fluid column process to achieve substantial elimination of cadmium and lead during the roasting of pelletized zinc concentrates. Designed to meet the need for additional feed for Matthiessen and Regeler Zinc Company's vertical retort zinc smelter in West Virginia, without recourse to a sintering operation, the plant is capable of simultaneously attaining very low lead and cadmium levels on demand, through operation in the manner described. Fluidizing air admitted via the wind box is supplemented by natural gas admitted via a tuyere bank 15 ins. above the hearth, in quantities adjusted to maintain a reducing atmosphere within the interstices of the bed. In addition, careful attention is paid to bed temperatures, which run from 1,080° to 1,100°C. Under these reducing conditions, 90 per cent of the cadmium and 92 per cent of the lead in the feed are eliminated, the sulphate sulphur content is decreased by 0.5 per cent, sulphide sulphur is held at 0.6 to 0.08 per cent, and the zinc content correspondingly in-creases. The fuel value of the natural gas is recovered as extra steam, which carries a credit. There are some added difficulties with fume accretions, gas conditioning and gas -cleaning, some of which have yet to be overcome."

Jan 1, 1967

By Tom Demorest

SMART is an association of mining companies that meet regularly to coordinate the technology development needed by the mining industry. Since 1995, the member companies and institutions have directed research and influenced the manufacturers and suppliers to improve surface mining technology and services. SMART actively supports learning seminars, collaborative research projects, and user groups. Members of SMART include some of the major surface mining companies in North America and Australia. These companies have recognized the value that collaboration can bring to the needs of individual organizations as well as the global mining industry.

May 1, 2009

By B. Tougas

Recycling of titanium represents an important economic activity due to high cost of the material and the amount of returns of machined parts which represent the bulk of finished titanium products (typical "buy to fly" of 10 in the aeronautic industry). In the present work, the metallurgical quality of 76 mm in diameter and 20 cm ingots poured in coated graphite mold will be assessed against the nature and condition of application of 4 coatings namely aluminum oxide, yttrium oxide, zirconium oxide and zirconium oxide with 4% aluminum oxide. The metallurgical quality has been evaluated in terms of alpha case thickness, microstructure and composition. Microhardness from surface will be assessed against casting conditions. Least square regression analysis have been use to optimize casting conditions.

Jan 1, 2011

By A. M. Cameron

THE HOISTING PLANT at the Stobie section of the FroodStobie mine is a two-shaft installation designed to handle a daily production of 18,000 tons of ore at depth. The two vertical shafts are within 100 feet of -each other, an arrangement made to provide the needed capacity and to give flexibility of operation (Figure 1). No. 7 shaft, used for handling men and supplies as well as for hoisting ore, has been sunk to the 3000 level and is served by a manhoist handling two cages and an orehoist with two 14-ton capacity Kimberley skips. No. 8 shaft, so far completed to a depth of 1,900 feet, handles only ore. The hoist is semiautomatic with push-button control and the skips are 15-ton capacity bottom-dump. The ore-loading pocket for first stage hoisting at both shafts is 120 feet below 1,600 lev-el and additional pockets are planned, as the shafts are deepened, at 800 foot intervals down to 4,000 feet.

Jan 1, 1956

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By S. Nikolic

"Calcium ferrite slags are currently used in a number of copper-converting processes. Despite the industrial importance of this system the phase equilibria have not been fully investigated. Characterization of this slag system is necessary to improve the control of process parameters, including fluxing and operating temperatures. Recently, a modified experimental method has been developed; this involves rapid quenching of slag samples equilibrated at high temperatures with the resulting phase assemblages analysed using electron probe microanalysis (EPMA). In the present study, experiments were completed under controlled temperatures and oxygen partial pressures using CO/C02 or H2/C02 gas mixtures. The investigated slags were supported during equilibration by a substrate of the primary phase. This technique removes the limitations arising from the use of crucibles and facilitates rapid quenching of the melt. Experiments were carried out at 1200°C and 1250°C (1473 Kand 1523 K) and in the composition range 0-40 wt.% Cu20, 0-25 wt. % CaO and 45-80 wt. % Fe203. Liquidus and solidus data are reported for the primary phase field of spinel between the oxygen partial pressures of 10-4.5 to 1 o- 6-5 atm. The analyzed compositions of liquids and solids are used to construct the phase diagram of ""Cu20"" -CaO-""F ez03"" system in equilibrium with metallic copper at fixed oxygen partial pressures."

Jan 1, 2007