Search Documents

By R. Stach, S. Gola, P. Zgrzebski, K. Soroko

"At the moment climatic conditions are a primary problem of the exploitation of copper ore. The efficiency of preventive actions in order to improve climatic conditions is connected with the knowledge of changing air in underground excavations. This article demonstrates the analysis of types of ventilation dams which are used in sealing abandoned areas on the maintenance of climatic working conditions in excavations has been conducted at the exploitation in Polish copper ore mines. INTRODUCTION The basis for mining activity performed by KGHM Polska Miedz S.A. is mining copper ores from the deposit lying at depths between 600 and 1,200 m below ground level. Activity has continued since 1963. The copper ore deposit is mined in ‘Lubin’, ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines, where difficult climatic conditions occur. The major factor moulding the climatic conditions in headings is the original temperature of rocks, being the result of geological conditions of the lying of the deposit and the existing geothermal degree. In the faces of present opening-out and preparatory headings, driven from mining areas of ‘Rudna’ and ‘Polkowice-Sieroszowice’ mines in order to open out deeper parts of the deposit, the original temperature of rocks reaches 45°C. Excluding the original temperature of rocks, the following are additional factors affecting the deterioration in the climatic conditions: • thermal properties of deposit rocks, • employed room-and-pillar mining systems, which are characterised by a large surface of exposure of rocks, • using self-propelled mining machines with diesel drive, • a high concentration of mining works, • setting up high-power electrical equipment in headings, • complex structures of mine ventilation networks, • a limited number of ventilating shafts, • constantly longer air-transport routes, • a significant accumulation of water increasing the humidity of supplied air. According to the valid Polish provisions (§21, 2013), the primary criterion of assessment of a climatic hazard is the occurrence at a workstation in an underground mining heading of an equivalent climate temperature of more than 26°C, which temperature is determined according to the following dependence:"

Jan 1, 2019

By Martin Junker

This Notwithstanding all the debates on climate change and renewable energy, coal remains the world's no.1 primary energy source even in the 21st century. In 2011 alone, total output rose from 420 million t to around 6.6 billion t. Similar growth rates are also expected for the next few years. In order to meet demand, new seams are being tapped and others mined far more extensively. In most cases, this means a move from open-cast to deep mining, and extracting coal from ever greater depths. At the same time, extraction processes such as the room and pillar method are being replaced by longwall mining, which significantly increases seam yield and therefore output. The depth of extraction with new, modified mining methods is increasing rapidly around the world - in most countries, much more rapidly than the corresponding expertise. A trade in mining expertise has therefore developed alongside the coal trade proper. Germany relies on coal imports, but can export mining industry services and advanced mining equipment. Geological conditions in the Ruhr and Saar coalfields forced Germany to drive forward development of deep working for hard coal years ago. For 30 years now, Germany has been mining hard coal at depths of over 1,000 m, and excavation is now at depths up to 1,600 m. Deeper extraction and more extensive excavation posed new challenges for both miners and equipment. Intelligent logistics, modern roadway development methods and longwall mining with ploughs or shearers combined with optimised process coordination offered pioneering solutions - solutions to enable costeffective coal extraction in the long term without compromising safety. Countries such as Russia, the Ukraine, China and the Czech Republic, where extraction is now reaching similar depths, can now benefit from this experience: they do not need to go through the same process of trial and development, but can draw on Germany's findings and ultimately save on costs. Now, Germany is offering this knowledge and experience on the international market on a client- and deposit-specific basis to continue providing mining countries with safe and cost-effective coal mining solutions and secure the energy supply. The presentation gives a number of examples of how international mining companies have used expertise from Germany to better meet the challenges of deep mining.

Aug 1, 2013

By Dave Shook

A Mineral Processing facility in Montreal has recently implemented a leading-edge intranet solution for monitoring the performance of plant operations, and providing condition-based maintenance. This innovative multi-faceted software implementation incorporates: web-delivered plant information systems; area-wide control loop performance assessment (using sophisticated algorithms to evaluate poorly performing controllers); and integrated alarm management functions. The system has enabled a project to improve plant operations through better process control. Maintenance technicians, engineers, supervisors and managers all can see the performance of the controllers, and the performance of the plant itself, through webdelivered graphics and reports. Information is combined from many sources, real-time, historical, relational and analytical, to provide a complete picture of plant operation. The web-based solution centralizes the administration of user access, and simplifies the deployment of several different kinds of information to many desktops. It is an extensible system that allows users to create and share their own web pages and data views. The paper will discuss the solution architecture and the improvements the I.T., operations, maintenance, and engineering groups have experienced, and overall benefits to the facility.

May 1, 2002

By P. F. Berry

X-ray fluorescence analytical techniques are fairly well established in the mining and metallurgical industries. In recent years, instruments utilizing radioactive isotopes have been developed which, owing to their more compact size, greater reliability and independence of substantial power supplies, are often preferred to X-ray tube installations. Analyses can now readily be carried out in the field, on the factory floor and in otherwise difficult locations. This paper describes many examples of radioisotope X-ray fluorescence for the analysis of metallic minerals, finished metals and alloys and also for the continuous measurement of metallic coatings, such as tin and zinc, on steel. Radiation scatter techniques are also described for certain analyses and for thickness and density measurements.

Jan 1, 1967

By K. U. Kainer

Magnesium and its alloys as the lightest available construction metal offer a wide range of opportunities for the usage in transportation industries, especially Magnesium wrought alloys with their improved mechanical properties show a high potential for structural applications, While magnesium cast components have found their application the interest is now spreading to wrought alloys due to the possibility to get even more homogeneous and better properties compared to cast parts, Therefore alloy and process development especially for extruded and sheet material is a main concern to enhance the application of Magnesium wrought alloys, Castings are still form the majority of applications of magnesium alloys, although efforts to develop adequate wrought alloys have increased, In the presentation, the alloy requirements for processing of cast and wrought alloys will be discussed, The various processing routes and alloy compositions result in specific microstructures and properties which determine the potential use of these alloys, Today, the spectrum of available alloys covers standard alloys as well as alloys for use at elevated temperatures, The trend will be to further diversify the alloy compositions and to improve the alloy properties, Areas of concern still remain the wrought processing and the high temperature (creep) and corrosion properties of magnesium alloys, Examples of recent developments in these sectors will be given, The presentation will also provide an overview of the historical and current use of magnesium and an outlook on future applications.

Jan 1, 2006

By K. Becerra, D. G. Almond, T. D. Maru

"Nkomati Nickel Mine in South Africa processes one of the world’s hardest ores in a 375k TPM autogenous grinding circuit. The plant employs an unconventional processing circuit, comprising a primary autogenous mill (AG or FAG) and pebble crushing circuit followed by a secondary hybrid pebble/ball mill and classification cyclone cluster.Advanced Process Control (APC) or Expert Control is now generally accepted as an advantage in most modern high capacity concentrator grinding circuits. This paper reviews the installation of model predictive control at Nkomati and examines the results and benefits of installation in an autogenous mill during plant ramp-up. The paper also demonstrates how predefining process control objectives together with good plant and supplier cooperation can achieve a robust and reliable APC implementation on a very short site program.The results conclusively demonstrate operational and economic benefits during circuit operation with the advanced process control system ON. Production performance and circuit stability were significantly better than during manual control."

Jan 1, 2012

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

By Neil Campbell

Abstract Following discovery on the Giant property of very promising gold deposits, some of which terminate against the steeply-dipping West Bay fault, a geological study was initiated co locate possible faulted extensions of the ore. Geological mapping revealed that the ore and the shear zones to which the ore is confined are older than the fault and therefore subject co displacement by it. It also disclosed several diabase dykes which seem co provide the best basis for determining the fault movement. After applying various techniques co determine their strikes and dips, the dykes were used as structural markers and it was estimated that, subject co certain possible errors, the movement on the fault was 16,140 feet (3.06 miles) south and 1,570 feet (0.297 miles) down on the west side relative co the ease. Evidence supporting this conclusion was obtained when subsequent deep diamond-drill holes intended to test the hypothesis cut an ore-bearing major shear zone which, so far as can be determined, is nearly identical with its present correlative on the Giant property. Introduction The fault under consideration follows a northerly trend past the west side of the original settlement of Yellowknife, which is situated 600 miles north of Edmonton and 400 miles from the Northern Alberta Railway terminus at Waterways, Alberta. The mining properties chiefly concerned include the southern part of the Giant claims, on the east side of the fault, and the Con-Rycon-Demelt claims, on the west side, 3Y2 miles to the south. Geological data were also obtained from the eastern part of the A. Y.E. property, which lies south of the Giant claims, and from the Negus, Meg, Yellorex, and Kam properties, which are south and southeast of the Con-Rycon-Demelt claims. Recognition of the major faults in the Yellowknife Bay area, including the West Bay fault which appears to be the greatest, resulted from the work of Dr. A. W. Jolliffe (McGill University, formerly of the Geological Survey of Canada) in 1935 and subsequent years. It has been stated with little exaggeration that these faults rank with the largest known steeply-dipping dislocations of the earth's crust. In the winter of 1939, a mineralized shear zone named the Creek Vein was found on the Giant property. It was noticed that the space relationship between the new shear zone and a body of quartz-feldspar porphyry is roughly the same as that between the Con C-4 shear zone and a body of acidic flows lying north of the Con property. Coupling this relation with the assumption that the movement along the fault is dominantly horizontal, it was postulated that the Giant shear zone represented the faulted extension of the Con C-4 shear.

Jan 1, 1947

By The Staff

Introduction For many years the necessity of mechanization of all the underground services in the collieries of the Dominion Steel and Coal Corporation in the Sydney, Pictou, and Cumberland coalfields has been foremost in the minds of those concerned with the engineering and operating policies of the Corporation, and a gradual policy of the mechanization of these services has been undertaken over the years, until nearly all the underground services, except the actual loading of the coal at the face, have been mechanized. Early in 1928, experiments in mechanical loading were conducted which finally culminated in the installation of mechanical loading units in our No. 20 colliery in 1938. This attempt at mechanization of the final underground services proved unsuccessful because the workmen were not ready to accept complete mechanization, and the fruition of many years of study was delayed until the year 1947. During the ensuing years, the engineers and operators of the Corporation had studied the possibility of adapting to conditions prevailing in Nova Scotia mines the many types of loading equipment in use in the United States and Europe. The varied physical conditions which exist in the fields operated by the Corporation rendered it extremely difficult to apply the equipment and technique successfully employed in the United States, and more recently in Europe, and special techniques have had to be devised to meet the need of each individual colliery. Prevailing physical conditions in the Nova Scotia fields find no parallel for mechanization with those of any other part of the American continent.

Jan 1, 1949

By A. Rodriguez-Prado, R. L. Legge, W. C. Lennox

ABSTRACT It is possible to adequately describe chemical reduction of hexavalent chromium, Cr(VI), in industrial and mining wastewater in constructed wetlands by applying different kinetic models (e.g., halforder, second-order). Accounting for hydraulic transport of contaminants in reduction equations can also improve such description. The authors developed an explicit advection-dispersion bulk flow equation and applied it to model Cr(VI) reduction in laboratory wetland mesocosms. The results indicated that the model adequately described wetland exit Cr(VI) concentrations and Cr(VI) reduction, representing an improvement over the commonly used graphic method and potentially improving the wetland design.

Jan 1, 2014

By N. Gharib, F. Hassani, P. Nekoovaght

"Novel rock breakage techniques are becoming more viable and attractive to industry. Microwave energy, as a thermal energy capable of inducing micro cracks through differential heating (therefore expansion) is a technology gaining considerable attention in mineral processing and ore comminution applications. Recently, the use of microwave radiation has been evaluated as a possible avenue for terrestrial and extra-terrestrial drilling applications as well as full face tunneling or rock breaking machines. As part of an overall research on use of microwave in rock breaking systems, the influence of microwave energy on the mechanical properties of common hard rock types as basalt has been investigated. The results revealed that microwave energy irradiation imposes micro and macro cracks to the surface of the rock being irradiated. In explosive free tunneling applications using TBM, jointed and cracked surface of rock eases the cutting process and increases penetration rate. The experimental setups have been simulated with the help of a multi-physics numerical modeling and the results have been compared with practical experiment. The wave propagation of microwave has been simulated and the distances where the power intensity is higher are identified. Experimental and simulation results underlined the potential impact of the use of microwave energy in underground or surface excavation applications such as mining and tunneling. This will also contribute economically when mine-to-mill operation is fully considered to improve the efficiency of rock crusher stages. INTRODUCTIONDuring hard rock breakage (i.e., separation of a piece of a rock from its parent deposit) in mining and civil applications, the performance of mechanical equipment such as tunnel boring machines (TBMs) is limited by high levels of bit wear and maintenance. Preweakening natural rock prior to breaking it by machine is one approach to lower bit wear and maintenance costs. Some preweakening methods apply heat directly or indirectly. For example, flame torch-assisted TBMs (Lauriello et al., 1974; Resource Technology, 1984) have been deemed economical in terms of equipment, but their feasibility is limited by high fuel consumption. Microwave energy could offer several advantages over the flame torch method: it does not produce emissions or increase fuel consumption (electricity source is available on the machine), and is easy to control (quick power on and off)."

Jan 1, 2015

By L. Heber Cole

Introductory During the past few years, salt (sodium chloride) strata have been encountered in western Canada in a number of wells, while prospecting for oil and gas. The ever increasing number of such wells points to the presence of a vast salt basin, the boundaries of which are at present unknown. This basin extends in a northwesterly direction from a point near the United States boundary south of Regina, crosses the Saskatchewan- Alberta boundary northwest of Unity, Sask., and continues with more northerly trend to Waterways and beyond. The beds, as encountered, appear to have a general dip to the southwest of between 10 to 20 feet to the mile and a pitch along the strike to the southeast. Thus one finds the salt strata at Waterways, Alta., at 600 feet below the surface (121 feet above sea level) whereas at Radville, Sask. south of Regina, the top of the salt is at a depth of 6,643 feet below the surface (4,430 feet below sea level). Whether this is a continuous salt basin or a series of separate basins is not yet known. We do know however, that in some of the well~ more than one salt horizon occurs while in others which normally should have encountered corresponding beds, the salt strata are absent. This latter condition, however, may occur only in the southern part of Saskatchewan, where a barren area seems to come in from the southwest. In the northwestern part of the basin, on the other hand, the occurrence of the salt strata seems to be more regular and continuous, and depths at which salt should be encountered in a drill hole in this part of the basin may be predicted with a fair degree of accuracy.

Jan 1, 1948

By C Carbonneau

In order to successfully produce columbium pyrochlore concentrates, St. Lawrence Columbium and Metals Corporation had to face two principal problems met in several new operations but possibly made more acute than usual owing to the newness of the project. 1.-The ore is particularly complex, as it is made up of an elaborate intermingling of carbonates and discontinuous ultra-alkaline rock bodies of various ages and types in which no less than seventy mineral have been re-ported. Obvious petrographic or structural controls are lacking. Ore boundaries have to be defined on the basis of assay results and the determination of several minerals which occur in trace amounts. 2.-The pyrochlore concentrates produced had to com-ply with a set of stringent specifications. This fact, combined with the low Cb205 content of the ore, necessitated the use of a beneficiation process that would have to operate at a concentration ratio greater than 100:1. A brief description of the mill circuit is given. Mill stability was obtained through extensive mineralogical study of the mill feed coupled with close geological and engineering control of the mining operations.

Jan 1, 1965

By S. Mostaghel, Fariba Azgomi, Steven Goodman, M. Oliazadeh

"It is known that copper loss to the slag phase can be in the forms of chemical dissolution and mechanical entrainment. The contribution of each mechanism to the total Cu-loss depends on different parameters and may vary significantly. To reduce emissions to the atmosphere and to shorten the converting cycle, most industrial processes are aiming at production of high matte grades. Increased oxygen-to-sulfur potential, required by these processes, results in a highly oxidized slag, which in turn leads to an increased concentration of the chemically dissolved copper in the slag phase. Hence, slag cleaning processes are becoming increasingly important for economic viability of the smelting operations. Hydrometallurgical, pyrometallurgical, and mineral processing routes have been used for copper recovery from slag. The current article reviews a trade-off study evaluating two of the commonly used methods (namely flotation and electric slag cleaning furnace) by comparing the technical pros and cons, operability/maintenance requirements, and capital/operating costs of the operations.INTRODUCTIONLarge volumes of smelter and converter slags are produced by copper smelters around the world. It is estimated that for production of each ton of metal 2.2 tons of slag is produced (Gorai, Jana, & Premchand, 2003). Considering the current pressure on the mining and metals industry for “zero-waste, sustainable and environmentally friendly” extraction of metals, it is absolutely essential for metal producers to improve their efficiencies in order to remain competitive. To meet these objectives, almost all metal producers, from steelmaking plants, ferroalloys, base and precious metals producers, are trying to reduce their metal losses to the slag phase. In particular, copper producers are aiming to produce higher matte grades in their smelting furnaces to reduce the converting time and improve their overall throughput. Copper smelters need to minimize their copper/precious metal losses to the slag phase before final landfilling/use of slag. The current article, therefore, briefly reviews the copper loss to the slag phase, methods of metal recovery from the slag and then presents a trade-off study conducted for a green field flash smelter of the sulfide concentrates. A comparison was made between two of the major process routes for metal recovery from slag, namely slag cleaning furnace and flotation."

Jan 1, 2016

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By D. V. Ziehlke, J. M. Franklin, T. M. Gordon, A. G. Galley

The Snow Lake-Wekusko Lake region of northern Manitoba conta ins numerous lode gold occurrences, including the largest gold deposit in the Churchill Prov ince, the Nor Acme mine. The Aphebian volcanic and sedimentary rocks of this region are comprised of submarine volcanic strata, overlain by turbidites, both of the Amisk Group, and fluvi atile sedimenta ry strata and bimodally composed subaerial volcanic rocks of the overlying Missi Group. Gold occurs as: 1) accessory gold in volcanogenic massive sulphide deposits, 2) lode gold in shear zones related to sy n- to post-FI thrust fa ults, and 3) lode-gold associated with post-F2 fault . An alteration a emblage of biotite, al bite and calc ite is associated with both groups of lode-gold deposits, and has been superimposed on the regionall y-developed metamorphic assemblages. AJthough these deposi ts are spatial ly related to britt le-ductile faul ts of different initial ages, they appear to have all fo rmed after the major period of reg ional fo lding and metamorphism, and thus may be penecontemporaneous. The alteration is different from the sericite-ankerite-quartz assemblage that is typically associated with gold deposits in Superio r Prov ince. Deposits in thi s area of Churchill Prov ince may have formed either at a higher temperature or a deeper structu ra l level than tho e in Superior Prov ince.

Jan 1, 1986

Agenda ?Trends in Wireless Technology ?Success and Opportunities ?Improving plants efficiency ?Improving plants reliability ?Improving plants safety and security ?Wireless Ecosystem ?Lessons Learnt / Recommendations Why Wireless? ?Lower cost (no wiring cost) ?Flexibility (no wire) ?Standards-compliant wireless devices major factor enabling growth:?Standard WLAN (IEEE 802.11)?Wireless field I/Os (IEEE 802.11, ISA100.11 and WirelessHART) ??Wireless adoption will become a milestone that will rival the introduction of Fieldbus and the distributed control system (DCS) in its importance.? ARC Advisory Group

May 1, 2009

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

By Edward (Ted) R. Lord

The application of thickened/paste tailings for surface disposal has been practiced for many years but has recently started to gain wider international acceptance. With tailings ponds coming under increasing environmental scrutiny, there is growing momentum towards mine/tailings plans that greatly reduce the size or even eliminate tailings ponds completely. This paper provides examples from the author's own experiences of the application of thickened/paste tailings for surface disposal in different countries, under different climatic conditions and in different industries. The paper will also comment on current research initiatives and future trends.

May 1, 2001