Search Documents

By H. C. M. Gordon

IT is essential to the success of any mining op::ration that the roadways through which the material wrought and ocher materials and supplies are to be transported should be kept in such condition that this transportation cart be effected rapidly and without difficulty. The longer the roadway and the greater the tonnage to be taken over it, the more necessary it becomes chat the construction and maintenance of the road be such chat traffic delays can be reduced co a minimum. le is proposed co deal with the development and construction of roadways serving longwall operations and, since a recreating system of longwall is worked, as a rule, only where roadways driven in the solid coal can be readily maintained, the discussion will be confined co advancing longwall roads which are driven through areas from which the coal seam has been totally extracted. In order to construct a roadway through extracted ground in such a manner that it will remain in a state of reasonably good repair without undue maintenance, it is necessary chat everything possible be done to bring the overlying strata co a state of equilibrium as quickly as this can be effected, and the operations should be so planned that future workings will not disturb the equilibrium so set up more than can be avoided. Obviously, the readiest way to obtain a stable roadway is to develop it by tunnelling through a settled waste. However, this cannot always be done, as some of the roadways must be developed and constructed as the walls progress, but level or lateral cut-offs can be constructed in this manner. Main-slope roads can be developed in a similar manner after the coal has been extracted and a waste formed for at !east five hundred feet on either side of the line of the permanent roadway from temporary subsidiary roads developed for this purpose along one or other of the flanks of the waste to be formed. This interval must be obtained in order chat the lacer extraction of the seam will not set up movements in the waste immediately overlying or adjacent to the constructed roadway, thus upsetting the equilibrium of the strata and distorting the road.

Jan 1, 1940

By R. K. Collings

Mineral wastes from the mining, metallurgical and chemical processing industries in Canada amount to about 800 million tonnes annually. Such wastes often are largely non-metallic in composition and are of interest for traditional non-metallic mineral uses and applications. Mineral waste disposal and maintenance are costly; furthermore, these wastes may pollute groundwater, rivers and lakes. These factors and an increased appreciation of the potential utility of some mineral wastes have stimulated research in this area.

Jan 1, 1984

"The Crescent, DM, and Pothook zones are copper-gold porphyry deposits which formed in association with alkalic intrusions of the early Jurassic Iron Mask batholith. The characteristics of the Crescent and DM deposits are nearly identical. Both formed along the contact between the Cherry Creek monzodiorite and Pothook diorite phases of the batholith. Permeable intrusion breccias along the contact concentrated the flow of hydrothermal fluids. Early, pre-ore alteration is represented by pervasive, sulphide-barren potassium metasomatism. The precipitation of copper-gold ore occurred during subsequent fracture-controlled potassic alteration, and is most strongly developed in chlorite-sulphide veins and their alteration envelopes. A central zone of potassic alteration is surrounded by a propylitic, pyritic halo in both deposits. The DM zone is unique among alkalic porphyry deposits in its high abundance of quartz-sulphide veins.The Pothook deposit formed at the westernmost contact of the Iron Mask batholith with enclosing Nicola Group volcanic rocks. Pervasive potassium metasomatism, similar in style to that at Crescent and DM, is associated with intrusion of the Cherry Creek monzonite. Pervasive and fracture-controlled albitic alteration is associated with intrusion of the Sugarloaf diorite and introduced minor copper-gold mineralization. Most of the copper-gold mineralization was introduced during formation of veins and breccia matrices dominated by magnetite/hematite and sulphide. Late-stage chlorite veining may have remobilized or introduced additional gold mineralization.Copper and gold assays in the Crescent deposit are well-correlated and have a nearly constant Cu:Au ratio, suggesting that the metals coprecipitated during a single hydrothermal event. In the Pothook deposit, copper and gold do not correlate closely, lack spatial correspondence, and suggest that transport and/or deposition of the two metals were not identically controlled and that they may have been introduced at different times by separate hydrothermal events."

Jan 1, 1995

By G. Beckstead, L. F. Sawatsky, R. Nutbrown, D. Long, G. Gould

"This paper presents a case study for optimizing water management at Gregg River Coal Mine located near Hinton, Alberta. The optimization study was derived based on a review and assessment of existing management practices and plans for future operation and final reclamation. A proactive water management strategy was developed to assist mine staff in adopting a rational, environmentally sound, and economical approach to water management. A plan was developed to provide for safe operation, self-sustaining operation, low maintenance, minimum negative environmental impacts, and anticipation of future needs for existing and future operations. A plan for final reclamation drainage was developed including establishment of effective, sustainable, and maintenance-free water management systems. The study demonstrated the importance and benefits of a proactive approach for integrated mine water management. This approach is recommended for other similar mine operations because it will improve environmental compliance and reduce costs of water management. IntroductionGregg River Resources Ltd. (GRRL) operates an open pit coal mine on the eastern slopes of the Rocky Mountains, located about 45 km south of Hinton, Alberta. GRRL opened the mine in 1982 and expects to continue operations after Year 2000. GRRL has progressively reclaimed the disturbed area and expects to complete mine-land reclamation shortly after mining in the area is complete. The existing disturbed area and reclaimed area covers approximately 9.5 km2 and will expand to about 10.5 km2 upon mine closure.Like other coal mines in the mountainous areas of Alberta and British Columbia, the GRRL coal mine is subject to highly variable temperatures and moisture conditions. Average monthly precipitation varies from a low of 12.6 mm in January to a high of 113.0 mm in August, based on the precipitation record at the mine site since 1982. Despite the relatively high rainfall during the spring and summer months, excess water problems during rainfall events are quickly replaced by water deficit conditions during periodic droughts. Surface runoff varies from near zero in the winter to a mean annual monthly maximum of 78 mm during the month of June. The mean annual surface water yield is 345 mm."

Jan 1, 1997

By S. Fahland, P. Vogel

"The Gorleben salt dome has been investigated since 1979 for its suitability as a repository for the disposal of high-level radioactive wastes. The geoscientific surface exploration was followed by underground exploration of the site beginning in 1983: underground excavation work included the sinking of two shafts from 1986 to 1994, the excavation of the infrastructure area and of drifts located in the first exploration area EB1 within the following years. The exploration was interrupted for ten years from 2000 to 2010 as part of a moratorium. After the expiry of the moratorium in March 2010, the geoscientific underground exploration at the Gorleben site was resumed. The investigations were interrupted again in autumn 2012 due to a political decision. The exploration programme included extensive geoscientific investigations: geological exploration, geophysical investigations, mining exploration and mining observation, laboratory tests, in-situ geotechnical measurements, geological modelling and numerical model calculations. To analyse and interpret the results of the in-situ measurements and mining observation geomechanical, thermal and thermo-mechanical model calculations were carried out. One of the main elements of the in-situ geotechnical investigations were high-resolution geothermal measurements performed in boreholes used for geological exploration and geotechnical tests.The geothermal measurements are used to evaluate several geotechnical findings, e. g. drift closure, rock deformation, stress change, and are completed by thermal model calculations to analyse and interpret the results of in-situ measurements and mining observation. The model calculations have been carried out using the special purpose JIFE code. To consider the whole exploration mine with the adjoining host rock as well as the successive excavation of drifts and boreholes in detail a three-dimensional finite-element model was developed. The model calculations are used to analyse the cooling-off of the surrounding rock of the drifts caused by ventilation. The cooling-off of the surrounding rock is an ongoing process affecting the results of further geotechnical measurements in the near field of the drifts. To predict a realistic time and space dependent distribution of the temperature field of the host rock within the exploration area which is influenced by ventilation thermal model calculations are necessary. Comparing the calculated temperature field with the in-situ determined rock mass temperature field within the exploration area EB 1 the results show a sufficient agreement. Furthermore there is very good correspondence, both qualitatively and quantitatively, between the experimental and the calculated findings regarding the temperature profiles including the effects of excavation and ventilation of the drifts."

Jan 1, 2015

By R. Scheepers

"Abstract -Mineral deposits and prospects of the Pan African Saldanian orogenic belt in the south­ western Cape Province South Africa, are reviewed. Despite the entire absence of operating base or precious metal mines in the area, this study has established at !east four metal associations that offer enticing exploration potential .The poly-phase deformed, low-grade metamorphosed volcano-sedimentary Malmesbury Group constitutes a complex, poorly understood supracrustal sequence that has been loosely subdivided into the Tygerberg, Swartland and Boland tectono-stratigraphic terranes by northwesterly trending fault zones. Syn- and post-tectonic granitoids of the Cape Granite Suite selectively intruded these terranes. Early S-types preferred the Tygerberg terrane whereas the later I-types dominate the remaining areas. Anorogenic A-type granites, however, occur in all three domains. Known metallization is directly or indirectly related to the intrusives, yet syngenetic deposits are conspicuously absent from the supracrustals. Four metal associations have been identified.•,Cassiterite-wolfrarnite (± Au, Cu, Mo, Fe-sultides) in quartz and quartz/aplite veins hosted by tourmalinized and locally greissenized S-type granite. Similar exo-granitic veins occur in proximal metamorphites.•,Juxtaposed disseminated, stockwork, breccia and vein style Cu-Mo-Fe-(Au)-sultide mineralization hosted by matie to intermediate intrusives of high K calc-alkaline, 1-type affinity.•,Cu-Mo-Au-sultides hosted by hydraulic breccia pipes, stocks and veins occurring in anorogenic A-type alkali feldspar granites and amphibole quartz syenites.•,Scheelite with minor Cu-Mo-sulfides and Au-associated with endo- and exo-skarns spatially related to I-type monzogranite, granite and alkali feldspar granite .The first three associations occur along the Yzerfontein-Helderberg-Zone, a 180 km lineament in the Tygerberg terrane, a zone exploited by syn-, late- and post-tectonic intrusives and their related mineralization. The fourth association is typical of the Boland terrane. The spatial and temporal relationships between the various metal associations is interpreted as the result of sequential intrusion of relative early high level S-type, followed by intermediate level I-type and finally anorogenic A-type granitoids during the evolution of a contracting continental margin arc and its inner arc. This plate tectonic setting suggests subduction in an easterly direction underneath the Kalahari craton. The spatial configuration of the various terranes at the present erosional levels is the result of rifting and significant differential vertical displacement following cessation of subduction, a terminal tectonic event possibly synchronous with intrusion of the A-type granitoids.Near surface preserved roof zones and cupolas of both S- and I-type granitoids in the Tygerberg and Boland terranes, respectively, render these areas extremely prospective for Sn, W, Mo and Au mineralization. The presence of intermediate to mafic volcanics, a diversity of calcareous lithotypes and favorable plate tectonic setting of the Malmesbury Group suggest potential for the thus far elusive VMS, MVT and Sedex base metal and minor precious metal deposits."

Jan 1, 1994

By Jason J. Ballentine

This case study presents the results of a maintenance review of a soot blower system at a coal fired power generation station. The power generation station was following a ?repair when it breaks? maintenance strategy for its soot blowers. The efficiency losses incurred as a result of failures in the soot blower system and the resulting interruption and out of service time was found to have a significant effect on the plant output. The maintenance strategy for the soot blowers was reviewed using Reliability Cantered Maintenance and lifecycle simulation. This methodology provided visibility to the monetary implications of failures and allowed alternative types of maintenance to be assessed and where justified were added to a maintenance schedule in the Maximo work order management system. By reducing unplanned breakdowns the predicted reduction in efficiency losses was 45%.

May 1, 2007

By J. E. Udd, L. P. Geldart, B. B. Dhar

"Solutions for the stress distributions around simulated underground openings have been limited to calculations of boundary stresses for simple openings in which the boundaries may be expressed in mathematical terms. Studies involving circles, ellipses and ovaloids are re-ported in the literature.The stresses on the boundary of an opening and those at a distance from it in the medium are of concern to the engineer. The former may be related to the greatest concentrations of stresses encountered; the latter have a bearing on the identification of the ""zone of influence"" of the opening.Recent advances, in the form of a derivation for the stresses at a distance from an opening of elliptical shape, together with a solution derived previously for stresses in depth around ovaloidal openings, have been combined with computer programming techniques to provide complete solutions for a wide range of cases and variables. Some typical results which, it is hoped, may have some application to the design of underground openings are given herein."

Jan 1, 1970

By John F. Kearney

After World War II Canada?s fledgling iron ore mining industry developed along the ill-defined Quebec / Labrador border near what became the town of Knob Lake and later renamed Schefferville. For about twenty-five years from 1954 to 1982 Schefferville was the epicenter of Canadian iron ore mining and the foundation of the Iron Ore Company of Canada. In about 1982 it all stopped, shut down, the miners moved away leaving behind a mining camp and a ghost town that have sat idle and almost deserted for the past twenty five years. The story looks set to change with new plans to re-establish the former mining operations in the historic mining camp. This paper outlines the proposal to reactivate the direct shipping iron ore operations in the Schefferville mining camp, and specifically the properties in Labrador owned or optioned by Labrador Iron Mines Limited (?LIM?), a wholly owned subsidiary of London Stock Exchange listed Anglesey Mining plc. The Schefferville mining camp is located about 1,000 km northeast of Montreal. There are no roads connecting the area to southern Labrador or to Quebec. Access to the area is by rail from Sept Iles to Schefferville, or by air from Montreal and Sept Iles.

May 1, 2007

By M. R. Hegge

The Jabiluka One and Two uranium deposits occur in Lower Proterozoic metasediments of the Cahill Formation, which is part of the Pine Creek Geosyncline in the East Alligator River area, Nothern Territory. The Jabiluka One deposit coincides with a "window" through unconformably overlying Middle Proterozoic sandstone of the Kombolgie Formation; Jabiluka Two is completely covered by that sandstone. The observed part of the Cahill Formation exhibits four horizons which are favourable hosts for uranium mineralization. These have been folded into an east-southeast-striking, gently plunging, open asymmetric syncline-anticline structure. The host rocks are mainly chlorite and/or graphite schists and their brecciated equivalents which have undergone initial regional prograde metamorphism to the amphibolite facies, then retrograde metamorphism to the greenschist facies. Mineralization consists of pitchblende, mainly filling open spaces and to a lesser extent in disseminated form. Chlorite, pyrite and quartz are commonly associated with the uranium mineralization. A portion of the Jabiluka Two deposit contains economic concentrations of gold. Structural preparation with low-pressure conditions at these sites appears to be the most significant ore control. Genetic hypotheses favour initial deposition in Lower Proterozoic sediments, followed by remobilization during later orogenic events. The deposits bear a marked similarity to some pitchblende deposits in central Canada.

Jan 1, 1977

By A. A. Millar

THE output of coal from the Province of Alberta reached its peak; in the year 1928, when 7,334,179 tons were produced. Following this, a steady decline was recorded, and in 1930 a low mark of 4,564, 290 tons was made. Since that time, however, the tendency has been upward, and this year (1937) 5,551,682 tons were produced, compared with 5,696, 375 tons in 1936 and 5,462,973 tons in 1935. The value of the output in 1937 was $14,434,969, against $14, 720,004 in 1936. The coals of Alberta have been classed under three heads, viz., domestic, sub-bituminous, and bituminous The domestic (or lignite) and the sub-bituminous coals are used chiefly for domestic purposes, with the possible exception of the smaller sizes and the output of the two stripping pits at Stereo and Coal Valley The bituminous output is used mainly by the railways, for locomotive purposes, which, in 1937, accounted for 80.6 per? cenr of the total sales of bituminous coal. A fair proportion is sold for stationary engine and steam purposes and, in 1937, 25,000 tons were used in making briquettes at plants operated by the Canmore Coal Company, Limited, and Brazeau Collieries, Limited. The International Coal & Coke Company, Limited, used 99,500 tons in their plant at Coleman, for making coke. The bulk of the 66,000 tons of coke produced was sold for use at the smelter at Trail, B.C.

Jan 1, 1938

By J. N. Van der Merwe, M. Mathey

"We present an analysis of the mechanical properties of coal specimens from various coalfields and seams in South Africa. Our database comprises of 1800 test results from uniaxial and triaxial compression tests, as well as indirect tensile strength tests, which we collected from the various mining houses and research agencies in the country. We inspected the database for possible errors and present a brief description of the verification procedure in the paper.In the analysis, we reveal that the collected samples of strength and elastic properties of South African coals can be represented by single lognormal or normal distributions with only few outliers. This finding indicates that the samples realistically approximate the population of mechanical coal properties in the country and may suggest that the properties are randomly distributed. Significant coalfield- or seamspecific trends for the mechanical properties of coal are not clearly discernible from our data.Typical coefficients of variation for the individual mechanical properties range between 25-50 % on a country-wide and seam-specific level of analysis. Average uniaxial compressive strength values, however, are closely clustered for all seams. A comparison with data available from international coal strength studies show the distinct difference between South African coals and seams in countries of the Northern Hemisphere, where differences in the average coal seam strength are more pronounced.We observe that the number of specimens whose failure mode is influenced by the presence of natural discontinuities reduces drastically with the application of very small confining pressures to the specimens. Further, the strength-reducing influence of discontinuities diminishes with increasing confining pressures."

Jan 1, 2015

By K. Szczesny

This paper considers the integration of uncertain real-time logistics data for reactive construction scheduling. In order to manage a construction project efficiently, an accurate schedule representing the current project progress is inevitable. The quality and up-to-dateness of such a schedule depends on the availability of real-time data. Typically, real-time logistics data contain information about the availability of material, equipment and personnel as well as delivery dates and site conditions. The accuracy and inherent uncertainty depends on the location where the real-time data was acquired. Currently, the integration of such data into a construction schedule is a very time-consuming, manual and, thus, errorprone process. Therefore, this paper proposes a methodology that enables an automatic integration of such uncertain data into construction schedules. By integrating uncertainties into the existing schedule their impacts on the construction work can be evaluated. For this, discrete event simulation is applied. In order to model uncertain input parameters for simulation models this methodology applies the fuzzy sets theory. In combination with alpha-cut sampling technique, discrete model input parameters are obtained. By applying reactive scheduling with several discrete event simulation experiments, the results can be used to modify construction schedules according to agreed timeframes and costs. In order to demonstrate and validate the presented approach an example is conducted.

Aug 1, 2013

By Jessica E. Heuchan

An industry survey has been conducted by the Queen's University Mining Engineering Department of 30 Canadian mining organizations to determine how effectively newly graduated mining engineers meet the needs of the industry. The principal objectives of the survey were to evaluate, and thus provide focus on change for, curricula being taught at Canadian mining engineering schools in service of the industry's needs; to provide feedback on current industry expectations; and to reinforce contacts with the industry as a means of providing future collaboration. A strong focus of the survey was placed upon industry's perception of the special attributes of engineering hires and applicability of student academic training to meet their industrial requirements. In providing this detailed summary of corporate responses, a clearer understanding of the mining industry's expectations of engineering training at Canadian colleges and universities has been gained.

May 1, 2003

By D. C. Fraser

Copper occurs invisibly in a geo-logical environment characterized by swampy conditions and an accumulation of forest peat. This swamp, located in southeastern New Brunswick, contains up to ten per cent cop-per (dry weight), in the organic sediments. This occurrence appears unique in that the metal is apparently organically combined in a chelate compound. Unlike the acidic nature of most peat bogs, the pH of the cup-riferous peat is nearly neutral. Analyses of the peat and associated soils have indicated that the bulk of the copper is contained in the organic sediments. It appears that the cop-per distribution is affected by capillarity, evaporation and the growth of frost crystals, and that the copper fixation is effected by organic sequestration resulting in the metal being bound to the nitrogen or oxygen components of the forest peat. While such a fixation mechanism is not definitely established as responsible for the immobilization of the metal, the facts at hand are compatible with

Jan 1, 1961

By Jacque Trottier, Marcel Vallée, Gratien Gélinas

"Mineral exploration in Canada traditionally has gone from boom to bust in cyclical pat-terns following market and discovery cycles, but other endemic factors related to exploration financing and performance have contributed to the amplitude and recurrence of these fluctuations. In view of these problems, junior exploration is reviewed here in a marketing perspective, looking at the 4 Ps: Product, Price, Placement and Promotion.In the 1980s, MEDA incentives gave the shares of junior and mining companies significant price and promotion advantages, and contributed to excessive exploration funding. Many were thus led to minimize the basic values needed for continued investor interest: appropriate levels of product quality, sustained share value and customer satisfaction. Basic changes are needed to improve the marketing of junior mineral exploration in the future, with or without improved fiscal incentives. To be successful, the required improvements must come from the technical participants, but the financial partners also need to be involved.Exploration in Canada must be marketed with vigour, both in Canada and internationally. Exploration, mine development and mine production are essential to our economy. They are environmentally acceptable and they are welcome in Quebec and in most Canadian provinces and territories. Canadian exploration and mining are entrepreneurial industries that must take better advantage of their strengths and achievements and remove the shortcomings that hinder them: nobody can do it for them!"

Jan 1, 1996

By Jonathan Ruiz Lizardo, Met-Chem Canada Inc., Flavio Ccuno, Constante Umipig, Ewald Pengel, José Ruiz

"Cerro de Maimón is located in the Dominican Republic on the island of Hispaniola approximately 75 kilometers northwest of the capital city, Santo Domingo. The processing facility consisted of two separate processing plants for oxide and sulphide ores. The oxide plant processed oxide ore bearing gold and silver ore using cyanide leaching and Merrill Crowe processes, while the sulphide plant produced a copper concentrate using conventional flotation. Cormidom is a commendatory example how mineral processing facilities can co-exist in balance with the environment. In 2014, natural occurring copper oxide contamination with finer grained copper-zinc sulphide mineralisation was expected to dominate the sulphide ore body. In anticipation Cormidom contacted the original plant designer Met-Chem to assist in overcoming this challenge. Test work indicated that increased flotation time and subsequent very fine grinding were required. Met-Chem provided the detailed engineering and Cormidom proceeded with the expansion project internally. Currently Cormidom has processed the sulphide ore successfully by implementing flotation modifications. This paper describes the history of Cormidom, test work on the “new” ore body, modification in process design in the Cu-Zn sulphide flotation circuit, construction and implementation.INTRODUCTIONCorporación Minera Dominicana (CORMIDOM) was a wholly owned subsidiary of GlobeStar Mining Corporation (a Canadian based minerals exploration company) with extensive exploration of base and precious metals in the Dominican Republic. In 2007-2008 CORMIDOM constructed the Cerro de Maimom project. The company was subsequently sold and purchased by Perilya Limited from Australia in 2013. Cerro de Maimón is located in the Dominican Republic on the island of Hispaniola approximately 75 kilometers northwest of the capital city, Santo Domingo. It is near the town of Maimón in Monsenor, Nouel Province (see Figure 1)."

Jan 1, 2016

By T. A. Utigard

To improve recoveries of Ni, Cu and Co in the Inco flash furnace, a new operating concept was investigated. By adding sufficient coke to form a supernatant coke layer, a reducing barrier would form allowing for improved reduction of descending oxidized sulfide mineral particles formed in the flame. The objective of this investigation was to study the kinetic mechanism and efficiency of the coke layer to produce a sulfur deficient matte. The mechanism and rate of carbon reduction of each of the phases formed in the flash flame, i.e. sulfides and oxysulfides were investigated by means of X-ray visualization tests. Graphite-slag reduction was also conducted for comparison purposes. In the case of slag, poor wettability and the formation of a gas film on the surface of the carbon reductant are often blamed for limiting the reaction surface area that ultimately results in poor reaction kinetics. The X-ray visualization tests confirmed that matte and oxysulfide wet coke better than slag and that the rates of reduction of matte and oxysulfide are faster than that of slag.

Jan 1, 2005

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By J. Y. Kim

This paper presents a novel action recognition method for observing human workers using interactions between actions and related objects on an internal construction site. This method can be used to measure work rates for labour productivity monitoring. This monitoring is critical because the performance of a construction project is significantly impacted by labour productivity. However, construction sites are generally crowded with a large number of workers and objects. Such congestion disrupts the accurate, automatic recognition of construction workers? actions. This congestion is one reason that existing automatic action recognition studies of construction areas mainly focus on workers? actions themselves. However, the crowded conditions mean that sites could offer a great deal of clues that could be used for automatic action recognition. According to psychological studies, interactions clearly take place between human actions and related objects, such as between hammering and a hammer. Humans use these interactions to recognize actions or objects more accurately. On the construction site, workers, materials, tools, and equipment are carefully planned out ahead of actual construction. The categories of workers and objects are pre-defined and, as noted, specific interactions define relations between worker actions and objects. In this paper, the interactions are limited to human workers and their hand-held objects. Action recognition results can be combined with hand-held object information to improve recognition accuracy. With the limited interactions, experiments in this paper show a significant improvement in action recognition. This paper describes the utilization of these interactions to improve construction action recognition accuracy based on human skeleton data and 2D color video from Microsoft KINECT sensor.

Aug 1, 2013