Search Documents

By P. Lind, A. Gagnon

"Goldcorp has embarked upon an ambitious, industry-leading, multi-year water use reduction effort. This is a proactive, voluntary effort that reflects our commitment to truly sustainable mining. This effort will focus on increasing water re-use and recycling, and reducing water inputs ultimately towards zero. All of our operating mines are expected to contribute to this effort and are currently in the process of developing plans to meet short and long term objectives. One of the largest needle movers to increase water re-use and recycling is in the area of tailings management. Within five to ten years at Goldcorp, it is envisioned that the need for wet tailings dams will be eliminated and that all new tailings facilities will consist of only filtered or dewatered tailings. Filtered tailings is developing into a mature technology with wide application in mine waste management. This paper describes a conceptual level evaluation on the transition from a slurry to a filtered tailings operation at the Cerro Negro mine in southern Argentina. Key benefits and challenges are highlighted.INTRODUCTION Goldcorp’s Cerro Negro operation is located in the Santa Cruz province in the Patagonian region of Argentina. Cerro Negro has been in operation since 2014 and commercial production was achieved on January 1, 2015. The processing capacity of the plant is 4,000 tonnes of ore per day and in 2016 produced 363,000 ounces of gold and 3.1 million ounces of silver (Goldcorp Inc., 2017). As the mine is located in a semi-arid area, it is important to evaluate technologies that could reduce freshwater consumption and maximize water re-use and recycle rates. The current tailings operation at Cerro Negro incorporates pumping of tailings slurry into a conventionally lined Tailings Storage Facility (TSF). Water is reclaimed from the tailings supernatant pond to the process plant via pumps, however, water losses occur due to evaporation and solution retention within the slurry tailings voids. Converting to a filtered or dewatered tailings operation would allow for increased water recovery prior to tailings disposal, and decreased water losses from evaporation and from retention in the tailings solids void space. This paper describes a conceptual level evaluation on the transition to filtered or dewatered tailings with the primary objective of moving closer Towards Zero Water."

Jan 1, 2017

By R. K. Borden

Rio Tinto is committed to proactive mineral waste and acid rock drainage management. Corporate requirements are closely aligned with the GARD Guide principles of early geochemical characterization and prediction followed by selection and implementation of management strategies to prevent or minimize ARD. Each operation is required to design and implement an ARD and Mineral Waste Management Plan. Successful implementation of the plan requires commitment at all levels of the company, from senior management, to geologists, mine planners, environmental staff and equipment operators. Examples of the successful integration of ARD management strategies into mine operations are cited from several mines.

Jan 1, 2011

By R. Vracar, D. Sinadinovic, Ž. Kamberovic

The paper presents a study on the oxidation of polymetallic gold ore by oxygen in an autoclave. It presents optimum parameters of autoclave leaching of sulphide refractory ore in self-generated sulphuric acid solutions aiming to get products with favourable technological characteristics from which precious and other useful metals can be recovered. A high partial oxygen pressure (1.5 MPa to 2 MPa), high leaching temperature (190°C to 200°C), pulp density 80 g/L to 240 g/L, ore fraction size 76 µm and leaching time up to 4 hours yield good results in rich ores. The full extent of copper and zinc conversion as well as a high extent of iron conversion has been achieved, while lead, gold and silver and a minor part of iron remain as a solid residue among gangue minerals.

Jan 1, 2001

By Javier Linares García

At then end of this year will be 10 years of producing concentrate for Antamina. This is a summary of what occurred over the last decade to increase production and tonnage above the design tonnage of 70,000 tonnes per day, up to an average of 100,018 tonnes per day in 2010, an increase in production of 42.9%. Equipment currently in use is the originally installed equipment, signifying a meaningful increase in capacity without capital. In this paper, the different phases of improvements and the realization of their impacts in chronological order will be outlined. Figure 1 below shows the average daily tonnage processed each year (tonnage throughput each year/calendar days), as well as the percentage increase over the tonnage of design.

Jan 1, 2012

By M. J. Gole, R. E. T. Hill, S. J. Barnes

"The Agnew (also known as the Perseverance) nickel deposit and its northern extension, the Rocky's Reward deposit, form one of the world's largest accumulations of nickel sulphides hosted by komatiites. Agnew was previously classified as an ""intrusive dunite-associated"" deposit . It has now been shown that the sulphides are hosted by komatiite flows which underlie an adcumulate-textured dunite body that crystallized in a large lava channel.The rocks of the mine area have been subjected to a metamorphic temperature of550°C and pressure of up to 3 kb. The komatiites have mostly been reconstituted to olivine-amphibole chlorite assemblages. There is a zoned sequence of enstatite-, anthophylite-, talc- and antigorite-bearing assemblages inwards from the western margin of the ultramatic reflecting variations in the CO/HP ratio of metamorphic fluids.Facing directions are determined from variations in the proportions of metamorphic minerals and in rock compositions which reflect asymmetric layering in the flows . Olivine-sulphides matrix ore is hosted in a single 50 m thick, east-facing flow that is overlain by flows containing massive sulphides. Much of the massive sulphide has been physically remobilized into fold noses, faults and shear zones. Chemical diffusion of ore components has upgraded a sulphide-rich metasedimentary unit where it is in structural contact with massive ore.To the north, the mineralized flow sequence is separated from a stratigraphically higher komatiite sequence, the Perseverance ultramafic complex, by approximately 150 m of felsic meta volcanic and meta sedimentary rocks. Southward, the Perseverance ultramafic grades laterally into an olivine adcumulate body and its lower contact cuts progressively down stratigraphy until it lies directly on top of olivine-sulphide ore of the mineralized flow sequence. This discordant contact is interpreted as the base of a thermal erosion channel formed by a voluminous komatiite lava flow. This contact greatly influenced later deformation of the mineralized flow sequence."

Jan 1, 1989

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By L. W. Vollmer

Introduction During the past three years at least fifty strings of 9% nickel steel tubing have exhibited excellent resistance .to the variably severe corrosive conditions typical of many of the sweet condensate wells in Mississippi, Louisiana, and Texas. This experience, and the characteristically outstanding performance of other ?nickel alloy steels under hydrogen sulphide corrosive conditions, dictated the selection of 9% nickel steel tubing for the second well drilled in the sour condensate Pincher Creek field of southwestern Alberta. The damaging effects of the Pincher Creek reservoir fluids on well equipment had been manifested in the discovery well by the rapid and not yet fully understood failure of API Grade N-80 tubing, stainless steel wire lines, and alloy steel fishing tools. Two very unexpected failures in the 9% nickel steel tubing, after only six days of service in production tests, instigated an extensive and continuing investigation to ascertain the probable cause of failure. This discussion presents some of the results obtained thus far which cast a little light on the perplexing behaviour of steels in hydrogen sulphide environments in general, and in sour condensate wells in particular. History of Tubing Failures Walter Marr well No. 1, in which the 9% nickel steel tubing failures occurred, produces from the Madison lime at the depth interval approximately 12,200 to 12,750 feet. The gas-oil ratio is about 26,000 and the gas contains 10.2 per cent hydrogen sulphide and 6.3 per cent carbon dioxide by volume.

Jan 1, 1952

By B. R. Johnston, K. D. Streeter

"ABSTRACTCoal Mountain Operations is the newest of Fording Coal’s operations although it is the oldest in terms of its historical production. In October, 1994, Fording purchased the former Corbin Creek/Byron Creek Mine. The mine is located in southeastern British Columbia, approximately 150 air kilometers from Calgary, Alberta. It was first developed in 1905 and has gone through a variety of owners in its 90-year history.This paper will deal with the remobilization strategy and the mining plans for the operation which are being implemented to make this operation competitive in the world export coal market. IntroductionIn October 1994, following a due diligence process, Fording Coal Limited purchased Coal Mountain Operations from Corbin Creek Resources, an employee group which had previously owned the mine. The purchase awarded Fording Coal Limited with 100% of the assets, and control of all the coal leases at Coal Mountain.The mine is located in southeastern British Columbia, southeast of Sparwood at the hamlet of Corbin, (Fig. 1).Rehiring of laid-off employees started in November 1994, with mining activities also recommencing in November. The coal preparation plant was restarted in December with one shift, went to two shifts in January 1995, and had four-shift, full-time operation in April 1996."

Jan 1, 1997

By A. E. Boone

"The paper presents critical areas in which improved coordination of effort by industry, government and sup-pliers will be essential to continue the growth record of the Canadian mining industry into the 'seventies'. The analysis includes: exploration, production, mining methods, research and development, markets, management and industrial relations. Performance objectives are suggested where tangible results can be measured. The author suggests the methods by which the 'seventies' can be the greatest decade in the history of Canadian mining. It is indicated that a national mineral policy is essential to the Canadian mineral industry."

Jan 1, 1970

By R. D. Brown

Manitoba has now joined Ontario and Quebec in providing for new incentives and lower tax rates for the mining industry. A single rate of tax (to replace the former two-tier royalty), an investment tax credit and a relatively straightforward set of rules for calculating taxable mining profits are the main features of new mining tax legislation announced by Manitoba's Finance Minister Donald W. Craik in his May 15, 1979 budget address. On introducing amendments to reform The Metallic Minerals Royalty Act, the Finance Minister indicated that the new tax regime is intended to restore the Manitoba mining tax system to a competitive position in Canada, and should result in renewed investment in the province's mining industry. 1n this regard, the government could be right-there is little question that the new tax regime will produce greater incentives for the mining industry than the two-tier royalty system introduced by the New Democratic government in 1975. The proposed changes, contained in Bill 57, would largely be effective January I. 1979.

Jan 1, 1979

By D. KEYS, D. E. Gemmell

The portion of the earth's surface covered by peatlands has been conservatively estimated at over 420 million ha (Kivinen and Pakarinen 1980). It is estimated that there are about 170 million ha of peatland in Canada. New Brunswick contains about 140,000 ha. Harvesting of peat for horticultural purposes has been carried out in New Brunsiwck since 1942. This industry, and the potential for using peat for energy purposes, indicated the need for an accurate assessment of the resource. In 1975, therefore, the New Brunswick Department of Natural Resources began a detailed peatland inventory. Assistance from the Canada Department of Regional Economic Expansion permitted acceleration of this program and field work was completed in 1982. Information gathered by the program will form the basis for a management plan for future use of the resource.

Jan 1, 1984

By A. Romero

"Most underground mines require heating or cooling systems to meet health and safety standards in the working areas. In regions where daily or seasonal fluctuations of environmental conditions exist, these systems tend to be over-sized and operate at low average load factors, which increase both investment and operating costs. One possible approach to reduce the temperature variations of the fresh air supplied to the mine, and so reducing the investment in large heating or cooling systems, is to use rock as a thermal regenerator or thermal storage system. Packed rock beds act as thermal inertial units, damping the atmospheric temperature oscillations to provide a more constant fresh air temperature. However, although regenerators exist in some mines, and packed bed rocks have been studied in detail in solar thermal power applications, there is a lack of tools to design new and sufficiently large storage systems of this kind. This work fills the existing gap by presenting a methodology to design and evaluate the impact on the ventilation systems of these regenerators. The method is validated using existing rock bed systems found in the literature and illustrates possible designs for small and large size regenerators in both hot and cold climates.1 INTRODUCTION “ It is quite amazing how often answers to extremely complicated problems can be obtained in this way, by using greatly simplified models of the real situation for the purpose of calculation.” Whiller, A. in private communication to J. S. Stachulak (1989). Motivation Most underground mines located in regions with extreme climatic conditions require the thermal pre-treatment of the fresh ventilation airflows, whether for heating or cooling. Heating commonly is needed in sites with sub-zero temperatures and is usually effected by direct or indirect burning of natural gas or propane. Alternatively, cooling is required in areas with hot temperatures, or in mines with high underground thermal loads where the fresh air at ambient temperature cannot provide enough refrigeration. Thus, when the ambient air conditions cannot provide by itself enough thermal power to ensure safe underground working conditions, a heating or cooling plant is required, which involves a considerable equipment and operation cost."

Jan 1, 2019

The current mining operations at Newmont Boddington Gold Mine (NBG) commenced in 2008, and commissioning of the processing plant started in the latter half of 2009. Metso Process Technology and Innovation were engaged to assist NBG with commissioning and project ramp-up through the implementation of a comprehensive ?Mine-to-Mill? Process Integration and Optimisation project. This methodology entailed extensive data collection which included drill and blast audits, ore characterisation, comprehensive comminution circuit surveys and review of operational data to assess the limitations within the current mining and processing operations. The results of these investigations have been used to define the operating base line of both the mining and processing areas and identify improvement opportunities. The use of modelling and simulations, utilising actual production data, has allowed for multiple scenarios to be evaluated, minimising the requirement for actual trials and thereby minimising impact on the operation. Improvements implemented to date include: the introduction of routine rock strength measurement for inclusion in block models, modifications to blast design improving ROM fragmentation and downstream comminution process performance, and changes to improve performance of secondary crushing and grinding circuits. Close cooperation between the mine and plant personnel is playing a significant role in overcoming the challenges presented to this operation and further improvements are targeted for the second full year of process plant operation.

Jan 1, 2012

By Joseph U. Messenger

A method of applying ammonium hydroxide to a drill stem containing hydrogen sulphide gas and hydro-gen-sulphide-bearing oil and water so as to remove the hydrogen sulphide as ammonium sulphide is de-scribed. It was concluded that the method allowed trips with drill pipe filled with sour fluids to be made more safely, more rapidly, and more economically. INTRODUCTION THE DANGER of poisoning rig crews during drill stem tests of sour wells by exposing them to hydrogen sulphide gas is well known in Canada. Concentrations of hydro-gen sulphide in sour gases range from 0 to 40 volume percent. There have been numerous casualties from hydrogen sulphide exposure during drill stem testing. Some have resulted in permanent injuries; in some cases the injuries have been fatal. For example, in Alberta in 1957 there were four deaths and 100 exposures which required medical treatment. These fatalities and injuries indicate the need for a more effective way of handling hydrogen sulphide in oilfield operations.

Jan 1, 1958

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By E. A. G. Colls

PART I.-GASES IN INDUSTRY INTRODUCTION THE part played by gases in industry can be considered from at least four distinct viewpoints, viz: (1) As air to support combustion and life and do various kinds of work (2) As fuel, or as essential to certain chemical processes (3) As sources of danger from explosion or fire ( 4) As hazards to man's health The present paper deals with gases only insofar as they are sources of danger, or are hazards to health. It may be noted, however, that, in point of tonnage, air is one of the most important materials handled in any industrial plant. In the operations of the Consolidated Mining and Smelting Company, for example, 138,000 tons of air are handled daily, the only material exceeding this figure being water. The United States Bureau of Mines has listed no fewer than seventy-four gases and vapours that, under certain conditions, may be considered as ex-plosive or dangerous (poisonous). The commonest and most important of these are as follows : Carbon monoxide Methane Acetylene Hydrogen Oxygen Hydrogen sulphide Benzol vapour Ammonia Petroleum vapour Carbon disulphide Hydrochloric acid gas Cyanogen Carbon oxysulphide Chlorine ` Fluorine (and fluorides) Acetone vapour Acetic acid vapour Water gas Natural gas Gasoline vapour Coal gas Producer gas Ether vapour Nitrogen oxides

Jan 1, 1940

By M. A. Perras, M. S. Diederichs

"The Niagara Tunnel Project (NTP) is a 10.1 km long water-diversion tunnel in Niagara Falls, Ontario, which was excavated by a 14.4 m diameter tunnel boring machine. The excavated rock types included limestone, sandstone, siltstone, shale and mudstone. Based on observations and measurements the overbreak was divided into four zones. Approximately half the tunnel length was excavated through the Queenston Formation, which locally is a shale to mudstone. Three of the four overbreak zones were within the Queenston. Zone 1 includes the formations above the Queenston Formation, Zones 2 and 4 are border regimes with little or no influence from St. Davids Buried Gorge and Zone 3 is the area influenced by the gorge. Zones 2 through 4 can be generally summarized as having overbreak as the result of stress induced spalling. Zone 2 marks the transition from slabbing at the Whirlpool contact in the stress shadow to spalling towards Zone 3. The behaviour of Zone 3 is interrupted from the typical high stress behaviour due to the presence of St. Davids Buried Gorge. As the tunnel passed from the gorge the high regional stresses induce spalling, which creates the typical notch shaped overbreak geometry of Zone 4.Three modelling approaches were used to back analyze the brittle failure process at the NTP: damage initiation and spalling limit, laminated anisotropy modelling, and ubiquitous joint approaches. Analyses were conducted for three tunnel chainages: 3+000, 3+250, and 3+500 m because the overbreak depth increased from 2 to 4 m. All approaches produced similar overbreak geometries to those measured. The laminated anisotropy modelling approach was able to produce overbreak depths and chord closures closest to those measured, using a joint normal to shear stiffness ratio between 1 and 2. The back analysis results were able to produce sets of stress and strength inputs for different sections of the tunnel at the transition from overbreak Zone 3 to 4. The back analysis procedure demonstrates the importance of including the anisotropic stiffness in the numerical modelling approach to correctly capture the overbreak geometry and deformations around underground excavations."

Jan 1, 2015

By A. Hekmat-Ardakan

Conventional hypereutectic Al-Si alloys such as A390 are used principally for the casting of components used in wear applications requiring abrasive resistance such as in engine or compressor blocks. A comprehensive study was undertaken to investigate the potential of improving the mechanical properties of these alloys by the addition of magnesium. A thorough thermodynamic study of the effect of the addition of Mg to the conventional A390 alloy showed that Mg2Si starts to form as a primary phase at 4.2% Mg as well as in the products of the binary and ternary eutectic reactions forming the matrix. Experiments were carried out in producing castings with different cooling and solidification rates of alloys with up to 10% Mg. Mg additions were found to increase the hardness over the as cast alloy due to solid solution strengthening. Also, T6 heat treatment greatly improved the tensile properties of these alloy compositions due to the strengthening effect of the theta-Al2Cu phase. The elongation of these alloys generally decreases marginally with Mg content. The most significant property improvement of the alloys with higher Mg content is the substantial increase in wear resistance. This is attributed to the dispersion of smaller particles of Mg2Si and their coherence with the matrix as compared to the large Si particles in the conventional alloy. A new rheoforming process for A390 is presented that improves the processing of the semi-solid slurry. Structure modification elements were also added to refine the primary and eutectic silicon greatly improving the processing of the semi-solid slurry.

Jan 1, 2011

By Robert B. Parsons

"The tax reform process marches on. The December 16, 1987 measures tabled by Finance Minister Michael Wilson represent one more step toward the objective of total reform of Canada's income and sales taxes. While the income tax changes are taking shape, much work still needs to be done on the sales tax side of the coin.IntroductionOn December 16, 1987 Finance Minister Michael Wilson tabled measures to implement the changes to Canada's income tax system that were proposed in the June 18, 1987 White Paper on Tax Reform. The measures were set out in a Notice of Ways and Means Motion; draft legislation relating to preferred shares, research and development expenditures; and draft regulations regarding capital cost allowance, certified films, flow-through shares, and the resource sector. The reaction of the government to the recommendations made by the Finance and Economic Affairs Committee Report on Tax Reform (the Blenkarn Committee), the Report of the Standing Senate Committee on Banking, Trade and Commerce and through consultations with interested groups and organizations, business, labour and individual Canadians is set out in a booklet of supplementary information.The basic features of the reformed income tax system set out in the White Paper remain. However, a number of significant changes have been incorporated in the Notice of Ways and Means Motion and other material. The following comments address those area s where changes have been made to the original White Paper proposals."

Jan 1, 1988

By Jeanne B. Percival, Paul Ramaekers, Charles W. Jefferson, Pat A. Hunt, Eric G. Potter, Katherine E. Venance, William Davis, Sean A. Bosman

"A 10-cm thick clay-rich layer near the top of the Manitou Falls Formation of the Athabasca Group is unusual in its breccia texture, alteration, and detrital mineral composition relative to the adjacent overlying and underlying sedimentary beds. This layer is composed of angular quartz grains set in an illite >> kaolinite + dickite matrix. Deformed clay-rich fragments within the layer have very similar mineral assemblages. The presence of euhedral accessory minerals including Ti-oxides and aluminophosphatesulphate minerals points to a diagenetic/hydrothermal origin. The presence of individual grains of Kfeldspar and amphibole is unusual relative to the typical Athabasca quartz arenite; originally, these minerals were probably included in detrital quartz and subsequently liberated during fracturing. The textures and alteration characteristics suggest that this layer is a hydraulically-fractured unit, which has experienced hydrothermal fluid alteration - a possible pathway distally related to uranium mineralization Une couche argileuse de 10 cm d’epaisseur pres du sommet de la Formation de Manitou Falls du Groupe d'Athabasca est remarquable par sa texture brechique, son alteration et la composition de ses mineraux detritiques qui different de ceux des couches sedimentaires sus- et sous-jacente. Cette couche est composee de grains de quartz angulaires dans une matrice composee d’illite >> kaolinite + dickite. Des fragments deformes riches en argile dans cette couche presentent des assemblages mineraux tres similaires. La presence de mineraux accessoires idiomorphes dont des oxydes de titane et des aluminophosphates-sulphates suggere que ces derniers ont une origine diagenetique / hydrothermale. La presence de grains de feldspath-K et d'amphibole est inhabituelle comparativement aux arenites quartziques typiques de l’Athabasca; initialement, ces mineraux constituaient probablement des inclusions dans le quartz detritique qui ont ete subsequemment liberees pendant la fracturation. Les textures et les caracteristiques de l'alteration suggerent que cette unite a subi une fracturation hydraulique et a ete alteree par un fluide hydrothermal - possiblement en lien avec les effets distaux de mise en place de la mineralisation en l'uranium."

Jan 1, 2013