Search Documents

By W. P. Campbell

Foreword At the outset, it should be stated that this paper does not pretend to present a panacea for the ills that 'frozen' wells are heir to, but rather is an attempt to bring to the attention of those whose special concern it is, a little theory and some facts, which have been brought to light recently, in connection with the problem of 'freezing' as it applies to naphtha-producing wells in the Turner Valley field, and to draw some conclusions that follow from the facts discovered. It should also be stated that the investigation is not to be regarded as in any sense complete, but in progress. Doubtless new facts will be brought to light from time to time which may modify present ideas on the subject, but whether favourable or contrary, these will be welcomed, as the purpose of the Department is to secure as complete information as possible of the factors contributing to 'freezing', since this must be the first step to an intelligent attempt to remedy or prevent its occurrence, if such can be done. It is possible, too, that the cause or causes of freezing may not be the same in all cases, but whether this be so or not will have to be determined later as new information comes to hand. Introduction One of the worries which must constantly confront the operators of gas-naphtha producing wells in Turner Valley-although all, fortunately, have not met with it-is the possibility of the occurrence of what is commonly called 'freezing' (going off production).

Jan 1, 1930

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

By Richard Poulin

Rehabilitation of mined out areas is often enforced by environmental bonding. It is usually assumed that this process provides financial assurance that rehabilitation will be carried out as agreed at the permitting stage. Shortcomings of the current practice in environmental bonding for mining are reviewed. Of particular importance for the public, for governments and for the environment is the absence of protection against cost overruns and companies defaulting before the bond amount is entirely paid. Elements of solution are identified through the emergence of environmental insurance as a complement to bonding for cost overruns and defaults. A cover of environmental catastrophes could also be added, hence reducing the risk for the public and the environment. We examine the merit of creating a captive insurance company under the responsibility of the mining industry. The use of insurance techniques would incorporate a genuine risk management dimension to the financing of rehabilitation.

May 1, 2004

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By A. P. Schissler

Mining has several characteristics, uncommon in other business sectors, which pose additional challenges to the implementation or design of IT and management systems that use the information. Understanding these characteristics would improve the chances of successfully importing new information technology and management techniques to mineral producers. The most important characteristics that should be understood are workplace issues, the industry’s dual nature of being a continuous construction project using cyclical factory processes, labour challenges, workplace culture, information availability, integrative data elements, and the current technical education of mining engineers. These characteristics were taken into account in two applications of information technology and systems design at operating companies. The research and consulting projects focused on the development of an IT-enabled performance management system at several underground metal mines in Canada and an integrated data warehouse for surface mines spread throughout the United States and Latin America.

Jan 1, 2006

By Frédéric Flament

The aim of this paper is to present the development of a data validation software as component of a commercial mass balance package. Data reconciliation through mass balance is basically an optimization problem constrained by the law of mass conservation. As any optimization problem solved with a modern and robust software application, erroneous information or starting point will always lead to a solution, whether it is realistic or not. Moreover, good information wrongly weighted by an incorrect error model will lead to the same bad ending. In an industrial context where competition requires accurate information, data reconciliation without validation can be disastrous and calls for data validation before and after reconciliation. The challenge in automated data validation resides in the development of general theoretical solutions. Until now, none has been presented and only partial solutions are available. The development presented in this paper incorporates some of these partial solutions. The integration of human knowledge into the application paved the way to a more general solution. The combination ?theoretical validation ? human expertise? proved to be flexible and reliable enough to be integrated in a commercial data validation package. Numerous examples though industrial applications are presented. These applications demonstrate the validation of raw measurements, user support in the development of error models and validation of reconciled measurements.

May 1, 2001

By C. L. Reichardt

"Pressure exerted on gold producers by regulators, project financiers, and civil society in the wake of the Baia Mare tailings spill in Romania during 2000 prompted most responsible gold companies to sign up to the International Cyanide Management Code for the Manufacture, Transport, and Use of Cyanide in the Production of Gold (the Code). The Code stipulates a ‘cradle to grave’ approach more comprehensive than that applied to any other mining reagent and poses particular challenges for operators who use cyanide-bearing tailings for backfill. This paper examine some of the challenges for Code compliance facing deep underground gold mines that employ backfill technology, most particularly the requirement to demonstrate that the potential migration of cyanide (and its degradation products) from emplaced backfill will not have an unacceptable impact on worker health and safety or on the receiving environment, either during mine life or after closure.Although the Code only contains a single reference to backfill, more careful consideration confirms that most sections of the Code that deal with tailings management are potentially applicable to mines where tailings material is used for backfill. Certain principles of the Code also pertain to aspects of operations, worker safety, emergency response, training, and dialogue with stakeholders relating to backfilling practice.For gold mines of the Far West Rand, the most significant cyanide-related risks associated with backfill operations relate to worker exposure to cyanide-bearing seepage and HCN gas. There is potential for seepage of cyanide-bearing water from backfill to compromise the beneficial use of surface and groundwater, and thus impact on downstream users and ecosystems. However, the extreme depth of mining and the specific geological and hydrological controls on the Far West Rand suggest that the potential environmental risks associated with backfill are likely to be considerably less significant than the cyanide-related risks to the workforce."

Jan 1, 2007

"The most widely used method for predicting the onset of continuous caving is Laubscher’s caving chart. A detailed examination of this method was undertaken which concluded that it had limitations which may impact on results, particularly when dealing with stronger rock masses that are outside current experience. These limitations relate to inadequate guidelines for adjustment factors to rock mass rating (RMR), concerns about the position on the chart of critical case history data, undocumented changes to the method and an inadequate number of data points to be confident of stability boundaries.A review was undertaken on the application and reliability of a numerical method of assessing cavability. The review highlighted a number of issues, which at this stage, make numerical continuum methods problematic for predicting cavability. This is in particular reference to sensitivity to input parameters that are difficult to determine accurately and mesh dependency.An extended version of the Mathews method for open stope design was developed as an alternative method of predicting the onset of continuous caving. A number of caving case histories were collected and analyzed and a caving boundary delineated statistically on the Mathews stability graph. The definition of the caving boundary was aided by the existence of a large and wide-ranging stability database from non-caving mines. A caving rate model was extrapolated from the extended Mathews stability graph but could only be partially validated due to a lack of reliable data."

Jan 1, 2003

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By C. Jay Hodgson

Hydrothermal systems form on land where and when an impermeable cap-rock unit ( either natural or self-sealed) , a permeable aquifer. and permeable discharge and recharge channels (cross-stratal permeability) develop in an anomalously hot part of the crust. A consideration of the relationship between magmatic and tectonic events in volcanically active areas indicates these conditions arise during: (1) the resurgent doming stage of the resurgent caldera cycle; (2) following movement on the bounding faults of tilted fault blocks ; and (3) as a result of hydrothermal boring associated with the intrusion of major sills. On the assumption that the submarine hydrothermal systems which deposit volcanogenic massive sulphide ores are comparable to subaerial hydrothermal systems, it is suggested that: (1) the horizon of mineralization corresponds to the time period when conditions favour the development of hydrothermal systems, as outlined above; (2) exploration for Cu-rich Cu-Zn-Pb or Cu-Zn ores should be directed to paletopographically high areas near discharge conduits , whereas exploration for Cu-poor ZnPb ores should concentrate on paleotopographically low areas down slope from conduits; (3) deposits with stringer zones lying above normally permeable units may be underlain by regionally extensive weakly mineralized and altered zones (self-seal caps) ; (4.) in the absence of a self -sealed cap, the ore horizon may be underlain by a naturally impermeable unit (e .g. a fine clastic sediment) ; (5) the condition of cross-stratal permeability may be evidenced by features such as dykes. alignment of vari ous magmatic and hydrothermal phenomena, abrupt thickness changes in stratiform units indicative of ponding against syn-volcanic faults, and fault-scarp slump deposits; (6) the condition of high heat flow may be evidenced by near-surface magmatism and steep thermal gradients preserved in metamorphic mineral assemblages.

Jan 1, 1977

By J. S. Fox

It is generally recognized that the interpretation of bedrock geochemical data in volcanic terrains can be improved by adjusting for rock-type. Various chemical attributes of volcanic rocks have been put forward in the literature as rapid indicators of rock-type, but there is some question as to which of these is the most reliable . Only one such attribute, total iron, seems to have seen systematic use in geochemical mapping in the Flin Flon region. Discriminant analysis of 500 basalts, andesites, dacites and rhyolites suggests that SiO2 is the most important rock-discriminating variable and that MgO, CaO, TiD2, AI2O3 and FeOtot, are successively poorer discriminators. Lithological normalization in the subalkaline volcanic environment should therefore be made over ranges of this variable. Trace-metal data from drill core through the sulphide orebody at Hanson Lake, Saskatchewan are used to demonstrate various approaches to lithological correction, including silica normalization, factor analysis and trend analysis. All of these extract economically important information from the core that is not apparent in the raw data logs. However, silica normalization does not seem to be subject to as many serious limitations as factor and trend analysis in this case, and therefore seems to provide the most reliable basis for the interpretation of subsurface exploration geochemical data.

Jan 1, 1978

By Scott Hopkins

Simulation tools are preferred for evaluating complex systems due to its ability to mimic reality and quickly evaluate many different what-if scenarios and find global solutions. A simulation model is capable of representing variable and dynamic disturbances that are typically encountered in day-to-day operations; this is where spreadsheet models or linear programs fall short because they cannot account for the dynamic behavior and relationships. The simulation model used for this work was developed by Xstrata-Nickel (previously Falconbridge). The simulation tool is very flexible and can be used to simulate different mining and development methods. The scope of the modeling included production mining, geology, equipment fleets, equipment maintenance and random failures, manpower, shift schedules, and cycle activity times. A case overview of the 170 Orebody will be presented along with the challenges associated with data collection for the model inputs. Results and lessons learned will also be discussed.

May 1, 2008

By B. R. MacKay

Introduction During the past six seasons the writer has been engaged in semi-detailed investigations on the coal areas lying along the front of the Rocky mountains between the Brazeau river and the Smoky River Coal Reserve (see Map, Figure 1). The purpose of this paper is to present some observations pertaining to the stratigraphy and structure of the district, touching especially upon the lithological units into which the Lower Cretaceous sediments have been divided, the thicknesses of the formations at different localities, the number, thicknesses and horizons of the principal coal seams, and the structural conditions which exist in the various fields.

Jan 1, 1930

By K. J. Heale, G. G. Richards, D. J. Rioux, R. L. Stephens

Slag fuming has remained a key process for the recovery of Zn, Pb, and minor elements in the integrated flow sheet at Teck Cominco's Trail Operations for more than 75 years. Since the start-up of the KIVCETTM process and the #3 slag fuming furnace in 1997, a range of process intensification projects have been completed to improve metals recoveries and throughput based on improved process control, mechanical modifications, and, most recently, the implementation of oxygen enrichment of the blast air. This latter project, initially named 'nitrogen depletion' and now 'nitrogen oxygen performance enhancement' (NOPE), is the primary focus of this paper. NOPE reduces the amount of heat required to heat the inert nitrogen gas, and therefore more of the energy input can be used for reduction. It also frees up boiler capacity because the inert nitrogen gas does not then have to be cooled down. A dynamic METSIMTM model was developed to determine the opportunities to improve the process capacity and heat balance to both assist with justifying the project and to verify the observed furnace behaviour. Several process safety management issues were also addressed and a few key minor mechanical modifications were made to allow the project to proceed to commercial implementation at 25% blast air oxygen enrichment. Short term plant trials have confirmed the model predictions. The first three months of a long term, continuous trial showed a 6% increase in zinc fuming rate from average furnace performance despite the implementation of a KIVCETTM fluxing change to assist with minor element recovery that was expected to negatively impact the zinc fuming rate by 3 to 5%. This encouraging result is also in line with the model predictions.

Jan 1, 2008

By Brad Marchant, Rick Lawrence, David Kratochvil

"BioteQ has successfully developed commercial operations for ARD treatment and selective metal recovery using the patented BioSulphide and Thiopaq® biological reduction technologies. The BioSulphide-Thiopaq process was developed to provide biogenic sulphide for the selective recovery of high purity metal concentrates from acidic wastewater, which are sold to recover capital costs and off-set water treatment costs. The BioSulphide-Thiopaq process can be used on a stand-alone basis or in conjunction with a lime circuit. Process advantages include: selective recovery of metals, very low metal concentrations in effluent, reduced waste sludge liability, reduced lime treatment costs and, in some cases, profitable sale of metal concentrates. Two case studies are presented to illustrate operations focused on metal recovery at the Caribou Mine, New Brunswick, Canada, and at Phelps Dodge, Arizona. A third case study is presented to highlight environmental control as well as metal recovery for treatment of ARD at the Raglan Mine in Northern Quebec. Process flowsheets, capital and operating costs are presented for the three case studies.INTRODUCTIONProtection of water quality has become one of the most important environmental challenges facing the mining industry. Although new mining projects can be designed to minimize impacts to the environment, many existing and abandoned mining operations have water quality problems. The principal cause of water contamination is acid rock drainage (ARD), which is generated when residual sulphide minerals in waste rock, tailings and other mine components and products are exposed to air and water. These reactions can produce acidity and elevated concentrations of metals in drainage and seepage that can adversely affect surface and groundwater resources. To meet regulatory criteria for water quality in the receiving environment, many mine operators must consider treatment of mine water and other effluents prior to discharge."

Jan 1, 2003

By Glenn Kosick, Roger Amelunxen, Glenn Dobby

"The variability in flotation response within an orebody is often a significant problem to address during the design phase of a flotation circuit. In addition, for existing operating plants, the reasons for such a variability need to be clearly understood and accounted for if plant performance is to be optimized. MinnovEX Technologies, in collaboration with major mining companies, is developing methodologies and tools to address the issue of variability in ore characteristics (such as ore hardness and flotation response). The tool is used for design and scale-up of flotation circuits from lab flotation data, and for prediction of recovery and final concentrate grades throughout the mine block model for any given circuit design.INTRODUCTIOTNH: EI SSUEB EINGA DDRESSEDThis paper describes the current development of a methodology and software tool for improved flotation plant design and enhanced prediction of froth flotation performance in an operating plant. The need for this tool is attributed to two primary factors: variability of flotation response properties throughout an orebody and related difficulties with scaleup from laboratory tests. Consider these in more detail.It is well recognized that separation performance via froth flotation will vary significantly within a single mineral deposit. This has been enhanced through the wide application of SAG milling. Throughput with SAG mills is more susceptible to ore hardness changes than is the case with crushing-rod-ball circuits; it is not uncommon to see SAG mill throughput to vary by up to 100% on a regular basis, e.g. 1000 tph to 2000 tph.The implication of this on laboratory testing for prediction of metallurgical performance is as follows: it is unlikely that either the plant grind (size distribution) feeding froth flotation or the flotation residence time will be known at the time of laboratory testing for a given block of ore. Hence, the grind used for the laboratory test is not likely to be that which actually occurs once the ore is processed, and the laboratory retention time may not represent the plant conditions."

Jan 1, 2002

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

By D. S. Flett

"The current state-of-the-art of chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is reviewed. General considerations regarding the various flowsheet steps are examined and options discussed. Then, individual flowsheets are presented and discussed. Finally, the forward prospects for chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is considered and conclusions drawn concerning the likely application of this technology in the future. IntroductionHydrometallurgical processes for treating sulphide concentrates, in general, have received considerable attention over the last three decades or more. Many flowsheets have been developed, many pilot-plant studies have been undertaken and several processes are now successfully operating. For example, direct ammoniacal pressure leaching has been used by Sherritt Gordon Mines since the 1950s to extract nickel from pentlandite concentrates, the roast-leach-electrowin route is widely used to recover zinc from sphalerite concentrates and direct sulphuric acid pressure leaching of sphalerite concentrates has been successfully commercialized. Also, Duval Corporation operated a direct cupric/ferric chloride leaching process (Schweitzer and Livingston, 1982) with electrowinning to recover copper from chalcopyrite concentrates, this process (now closed) being the only chloride process which has been commercialized for a sulphide flotation concentrate. Despite these developments, it has long been considered, particularly for copper sulphide concentrates, that direct hydrometallurgical processes are in the main unlikely to be able to compete successfully with smelting for large-scale operations of simple high-grade single metal concentrates. As long as such concentrates can be produced commercially, smelting is likely to remain the principal processing route (Flett, 1981). This view is being challenged nowadays through pressure leaching developments made by Dynatec and CESL in Canada and the recent start-up of the Western Metals Gunpowder plant at Mt. Gordon in Queensland (Flett, 2000). Complex sulphide ores offer even greater opportunities because of the ability to produce a bulk sulphide concentrate from the complex sulphide ore with considerably higher metal recovery than is often possible from the production of individual metal sulphide concentrates from differential flotation. Interest continues to focus on hydrometallurgical solutions to these processing problems, particularly with regard to chloride hydrometallurgy. This paper, therefore, reviews current state-of-theart with respect to chloride hydrometallurgy"

Jan 1, 2002

By Susumu Tsubota

Three types of reference gold catalysts, i.e., 3wt%Au/TiO2 (Au-Ti: Type A), and 0.3wt%Au/Fe2O3 on alumina beads (AUS: Type B), and 5wt%Au/Fe2O3 (Au-Fe: Type C), were produced in a test plant scale by Sud-Chemie Catalysts Japan, INC. under the licensing of AIST. To evaluate the validity of the preparation methods and conditions used for the reference samples, elemental analyses by ICP, particle size measurements by TEM, and catalytic activity measurements for the oxidation of CO and H2 over these catalysts were made. Gold catalysts can be prepared in a large scale of ca 400g for the Au-Ti and Au-Fe catalysts, 5 kg for the AUS catalyst with good reproducibility. It was confirmed that they were available for useful as the reference gold catalysts of World Gold Council.

Oct 1, 2003

By H. E. Pawson

"COMMON METHODS OF ELIMINATION: The four methods most frequently used to dispose of cyanide wastes are:1. Oxidation2. Dilution with water or with cyanide free wastes3. Acidification and dilution of resulting gas with air4. Alkaline ChlorinationMost operators practice a combination of the first two methods, allowing oxidation and dilution of cyanide waste in tailings ponds. Then, pond effluent is introduced to a stream for further dilution andoxidation which is expected to take care of the cyanide. This method oftreatment does work to a certain degree. Atmospheric oxidation in tailings ponds and in receiving streams chemically breaks down the cyanide radical to form carbon dioxide and nitrogen.2(CN) + 202 2 CO2 + N2The monetary advantage to this method is obvious to the operator but too frequently though, climatic conditions are ignored. Length of winter, and reduced flow of the receiving stream in summer, adversely restricts the result of this combined method. For those of us who rely mainly on dilution it would be wise to remember that 70 million pounds of water are required to dispose of one pound of sodium cyanide (1).The third method outlined involves addition of acid in a closed vessel and venting resulting gas to atmosphere with or without air dilution by mechanical means. Cost, safety and some form of secondary treatment to complete destruction of cyanide remaining in the solution usually make this method prohibitive.The alkaline chlorination method is the one most commonly accepted for treating cyanide bearing wastes since it is felt that cyanide is completely eliminated in this manner."

Jan 1, 1973