Search Documents

The use of ammonium nitrate/fuel oil explosives is.now well established in most open cut mining operations. Its use. is extending to underground mining. This has been due in a large measure to improvements in the nature of the ammonium nitrate made available from various sources. The addition of surface active agents and water in controlled amounts to the fuel oil has been found to increase the sensitivity of the ANJFO mixture with consequent better explosive properties. It is considered that the surface active agent increases the bond between the ammonium nitrate and fuel oil giving a more, intimate physical and chemical mixing of the oxidising and reducing agent. This results in increased sensitivity and a faster rate of reaction. The increase in sensitivity has been accomplished without any diminution of safety. Tests which demonstrate the safety of this type of explosive are given in the appenuix.

Jan 1, 1964

THIS instrument, depends on the principle that, over a short period, the surfaee of a porous substance from which a liquid is evaporating receives the same amount of heat by conduction, convection, and radiation as it loses in the latent heat of the evaporating liquid. If, then, the amount of heat being received by a surface can be measured, the rate of evaporation can also be obtained. The Kata thermometer is also based on this principle differently applied.The instrument, as shown in Fig. 1, consists essentially of a thermometer with a sliding which is divided by three pointers into two equal parts which may be spaced so as to cover a distance of, for example, 5° of the thermometer scale. The instrument is calibrated so that the amount of heat required per unit area of the bulb to raise the menissus is known. The method of using the instrument is as follows:The slide is first set so that thc central pointer is at the temperature of the evaporating surface.The thermometer is cooled by any convenient means so that the meniscus is several below the lowest pointer. The thermometer is then placed near the evaporating surface, when the Ineniscus begins to rise and the time taken for it to rise from the lowest to the top pointer is measured. From this and the calibration results the amount of heat retained per unit area of the bulb at the mean temperature...

Jan 1, 1928

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: How do mill lifters and liners really work and have an effect on grinding? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the æextremeÆ form the major observations and conclusions expressed in this paper are that: the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; the often promoted theory that balls impacting the ætoe of the chargeÆ is a dominant form of breakage is incorrect; and fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

Launching the Queensland Water Plan 2005 - 2010 in August 2005, Premier Peter Beattie compared the stateÆs water resources with liquid gold. QueenslandÆs peak industry body for the minerals and energy sector, the Queensland Resources Council (QRC), believes the analogy is appropriate. During early development of an industry water strategy, it has become apparent that water is like liquid gold, in that it is revered, hoarded, recycled, priced on purity, a magnet for speculators, both difficult and expensive to transport effectively, heavily regulated and fundamentally linked to issues of security. To date it has generally been economic and relatively straightforward for the resources sector to secure water. Although production has not been compromised, this must not be grounds for complacency as there is every indication that water will continue to become increasingly expensive, more tightly regulated and, relative to a growing demand for a finite water supply, increasingly scarce. During 2006, QRC has developed and is implementing a voluntary industry water strategy to address a range of challenges confronting the resource sectorÆs security of access to water. As a consequence of, at times, protracted community consultations over QueenslandÆs catchment-based water planning processes it has become clear that many community stakeholders have outdated perceptions of the stateÆs resources sector. Once established, QRCÆs water strategy will incorporate a community engagement campaign to present the industryÆs credentials as a leader in water resource management. The development of QRCÆs water strategy, and the challenges the strategy is designed to address, provides insight into the fundamental reforms that are occurring in how water is managed and regulated in Queensland. These reforms have implications for how government policies are designed and administered and also for how industry engages with communities during this transition process.

Jan 1, 2006

Mine planning is difficult. Even for small operations, it involves reasoning with complex variables and the practical difficulties of mining. It is also about predicting and planning the future in an unpredictable physical and economic environment. Yet we rely on a handful of individuals and their spreadsheets to tell us how to do it û planning the business and activities of mining to hopefully produce results that will please stakeholders. Does it work? Not as well as it could. Planning affects everyone in the organisation. Company executives are demanding more reliability and stability in cost and revenue forecasts from their operations. Management want to explore ways of being more cost effective. Miners and contractors want more useful plans and realistic targets. And the planners have to describe the method that will translate business objectives into implementable plans. Even with the use of computer technology a lot of effort is expended to produce plans that are largely qualified by the level of knowledge and experience of individuals. Better use of information and the application of Intelligent Technologies can improve the quality and reliability of mine plans and schedules. By capturing the knowledge within the organisation and speeding up the planning process, Intelligent Technologies allow more options to be considered more rigorously. But it is not just about technology. It is about how technology is implemented and embodied in the way the business is managed for performance. When this happens, the real benefits of better planning start to flow.

Jan 1, 2003

Microorganisms have been used throughout history for the benefit of mankind with some of the earliest applications being in the production of fermented foods and beverages. Reactions involving inorganic substances such as metals, sulphur and sulphide compounds were hardly ever used until the early 1900s when it was discovered that Thiobacillus ferrooxidans was capable of promoting the oxidation of metal sulphides in ores. Today, it is widely recognised that biotechnology has great potential in the minerals industries, particularly in such areas as the leaching of low-grade ores of metals such as copper, gold and uranium; removal of heavy metal ions from process streams and from liquid process wastes; and in the desulphurisation of high-sulphur fuels. Although widespread commercialisation of mineral biotechnology has not yet been achieved, it is estimated that by the Year 2000 mineral biotechnology will have a significant impact on the minerals and metal industry and will probably account for tens of billions of dollars worth of annual production world-wide. This paper examines the actual and possible future applications of biotechnology in the minerals, metal refining and fossil-fuel processing industries. Firstly, the important chemical (and biochemical) principles involved in bio-dissolution of metals from ores and solid wastes, and in bio-accumulation of metals from process and waste solutions are reviewed, including leaching practices - past, present and future. Microbial desulphurisation of coal, and microbially-enhanced oil recovery are also discussed. The practical aspects of genetics and genetic engineering, the types and characteristics of those microorganisms important to mineral biotechnology, and the current research trends are reviewed as well. KEYWORDS: Biotechnology, microbial leaching, bioaccumulation, biosorption, bioleaching, biohydrometallurgy.

Jan 1, 1993

By B L. Dickson, J H. Hodgkinson

The self-organising map (SOM) is an exploratory data mining technique that is both non-traditional and underutilised. Methodologies based on SOM tend to be data-driven and unsupervised, which makes them ideal to assist in the integrated analysis and interpretation of complex and disparate æmineral explorationÆ data sets. While traditional statistical multivariate approaches have difficulty with relationships that are non-linear and data distributions that are not normal, SOM-based data mining procedures are useful in these circumstances. In a SOM analysis each sample is treated as a vector in a data space defined by the variables; and measures of vector similarity, such as the dot-product or Euclidean distance, are used to order or segment a data set into naturally occurring populations. These groupings are positioned as nodes, or groups of nodes, on a 2D rectilinear representation of the multi-dimensional ædata spaceÆ, which is the æself organized mapÆ. While it is common not to include a sampleÆs locational information in the actual SOM analysis, such information can be used to display the spatial location of samples coded by their SOM node or cluster. If one finds there are coherent spatial patterns belonging to samples from particular nodes, or groups of nodes, then there is strong evidence that the technique is determining patterns and relationships within the data that have natural significance. Variations of the SOM technique may be used to perform broad categories of operations, including: 1. outlier identification û for samples belonging to various nodes or grouping of nodes; 2. function fitting, prediction, estimation or imputation û for calibrating relationships between variables and determining replacement values for missing, null or censored values; 3. clustering, pattern recognition or noise reduction û for determining the natural patterns within a data set; and 4. classification û for classifying samples into the clusters determined in three. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This paper aims to provide some' new and original thoughts on tungsten carbide drill-bits and describe practices and performances, some of which are unique and most of which have not previously been described. Many theoretical and descriptive papers and articles on carbide bits have appeared during the last few years, and in the big majority conclusions such as these were made. These results are marked by premature failure of the bits, or The full or economic life of the bit is seldom reached due to the premature failure of the insert. Unfortunately those conclusions are seldom accompanied by the reasons for premature failure. In the few cases where reasons for failure have been advanced, very little, originality has been shown. The reasons usually given are that the failures are due to bad operators, bad workmanship, faulty steel or unsuitable machines, but it has been shown at Mount Isa that the chief reason for poor performnce is bad design.The first question asked will be, "What is wrong with the design of most bits?" and the answer'is, "The size of' the inserts". There may be many other small faults iiI different types of bit but Mount Isa experience indicates that the size of the insert is the most important factor influencing pit life. Under normal conditions it has been found, that there is a minimum size of insert that will give satisfactory performance, and this minimum is 5/16 in width and ? in. depth at the shoulder. A big majority of the bits at presentavailable in Australia do not satisfy these requirements.

Jan 1, 1953

By A. W. CAMERON

Over a 4 hr period of steady plant operation samples were taken at regular intervals from points within the grinding and flotation circuits. Size fractions of each composite sample were analysed for lead and zinc values and a comparison made of the behaviour of the lead, zinc, and gangue minerals, size by size throughout the whole circuit.Analysis of the breakage behaviour using dynamic mathematical models gave the rates of breakage of each size fraction of each main component. Simulated grinding experiments showed that the main grinding circuit had some reserve capacity.In the lead flotation circuit all lead values between 150 mesh (Tyler) and 5 microns had excellent flotation characteristics, and a major proportion had a high rate of flotation which was practically the same for all sizes. Increase in overall lead recovery would require improvement of the flotation behaviour of ultra-fine lead minerals. These were slow floating and were responsible for approximately half the lead losses in the final zinc concentrate and one-third of the lead losses in the final tails.All sizes of zinc values between 100 mesh and 7 microns floated well and the performance of the zinc flotation circuit was mainly limited by the relatively poor flotation of the very fine zinc values. Approximately 60 per cent of the zinc lost to the final tails lay within the minus 7 micron fraction.The overall flotation conditions were conducive to very good selective flotation of the major proportion of the values and limitations in metallurgical performance were mainly due to the properties of the ultra-fines.

Jan 1, 1971

By Rashkovski GB

Until recently amalgamation has been the main process forextracting large gold particles from gravity concentrates obtainedduring the dressing of ores and placer gold deposits.Development of new technology for treating the gravityconcentrates was necessary because of the harmful effect ofmercury on subsequent production processes and theenvironment. The harmful effect of mercury is particularlyevident in the resin-in-pulp process that is widely applied inRussia.

Jan 1, 1993

There is a link between the requirements of society and the determination of curricula in tertiary educational institutions. Mineral resources exploration provides a strong example of this link. The resources exploration business engages in scientific, engineering, commercial and management activities in an endeavour to discover economically extractable commodities. Most geoscience and geotechnical graduates are employed by the mineral industry for resource exploration and development. This industry comprises a wide range of employer groups which include the Bureau of Mineral Resources, CSIRO, energy authorities, State geological surveys, State water commissions and private companies. Such employers are variously charged with the task of understanding and utilising earth resources to the benefit of society. It follows therefore, that undergraduate education and post-graduate specialization should be directed towards meeting the needs of employer groups in the geoscientific and geotechnical fields. In the past the training of most Australian geologists has emphasised classical science. This type of training remains of primary importance in the early undergraduate years but there is a need for modern educators to recognise the increased desirability for the inclusion of geotechnical subjects in the curriculum. Modern geo-education should address four main sectors when deciding curricula:

Jan 1, 1986

Deep lead mining by methods other thanconventional open-cut techniques has not been effectively employed in Australia in -the second half of this century. The reasons for this are essentially economic, and are related particularly to the labour intensive nature of the methods involved as well as the high consumption of support materials. These methods have been adapted in recent times to undertake bulk sampling programmes in deep leads. Although some consideration is given to surface-oriented hydraulic and solution mining applications, the prime function of this paper is to investigate the possible application of modern underground methods to deep lead exploitation. As deep leads are not currently being worked (with the exception of some minor operations on the Eastern seaboard), these applications remain essentially untested. They have, however, been conceptually developed following several years of small scale deep lead development. Current mineral economics, particularly with respect to gold, combined with the known extent of partially - or totally - unexploited mineralised leads demonstrates the necessity to investigate all possible means of ore extraction.

Jan 1, 1985

By F Jiao, J Wang

By the year 2000, China was the sixth largest gold producer in the world, with about one-quarter of total production being derived from refractory or semi-refractory deposits. Although bacterial oxidation plants had been previously tried in China using local technology, these plants had not been commercially successful. The Laizhou Gold Enterprise (Tarzan BioGold Co Ltd) located in Shandong Province, undertook to modernise their gold processing facility in 2000 with the introduction of Bacterial Oxidation (BACOX) Technology. In 1997 BacTech Australia and Mintek of South Africa had formed a technology partnership, combining forces in the provision of bioleach technology. Under a cooperation agreement, BacTech/Mintek were chosen as the preferred technology providers for this first application of commercially proven bacterial oxidation technology within China. The paper describes the successful operation of this plant over the last three years. The events of project implementation are described, from the metallurgical testing of concentrate; through to the commissioning at the design throughput of 100 tonnes per day resulting in 80 000 ounces (2.5 tonnes) per year of refined gold. Process aspects of the operation encountered over the last three years are discussed which illustrate the robustness of the operation. The success of the bioleach facility has led to an advancement of plans to double plant capacity and some of the innovations, which may be employed in this expansion phase, are discussed.

Jan 1, 2004

Mine Dewatering for reoccupation of a flooded mine requires rehabilitation and recommissioning of shaft and sane level functions to provide safe efficient access, services and logistics, as well as securing connections with all exposed workings. The objective is the earliest secure reoccupation of the target depth horizon for minimum water pumping, consistent with an appropriate investment and optimum schedule of operating inputs to the dewatering, redevelopment, services and consolidation processes. Strategy must focus on recommissioning of relevant functions in the shaft and at stage pumping horizons, advance of logistics close to pumping and rehabilitation, management of the secured exposed workings. The progress must be systematic, sustained and integrated, and must be secured against risk and uncertainty. There must be a strategic capability to respond effectively, and manage interruptions to processes, conditions requiring higher or different resources, and contingencies which affect schedule, budget or risk profile for the continuing programme. Planning must aim to reduce or contain risk or uncertainty elements and contingencies, limit interruption frequency and severity, identify and provide the capability for efficient responses. It is appropriate to model and simulate the reoccupation analogous to a mine initial development production programme. Only minor changes to relationships and relativities of models for Capital works, Operations (Production and Development) and Services/Logistics are needed but the model for management of workings is more relevant than that for depleted workings in an operating mine because of the water and other transfers. An important difference is the unsteady state of operations which requires probabilistic modelling of availability and utilization of equipment and processes.

Jan 1, 1988

IT is most remarkable and valuable property of mediurn and high carbon steels that they should be so susceptible to heat treatment, the wide range of variability in tenacity, ductility, etc, due to the normal influence of the carbon in the untreated material being enormously inereased thereby.The physical properties of steel and other metals are much more closely related to their structure than to their ultimate analysis.For instance, we may by chemical analysis determine the carbon content of a steel to be 0.5% ; but this information alone is insufficient to enable us to say what are the physical properties of the metal.Such a steel may possess 11 tensile strength of anything from 35 tons per sq. in., with much ductility, up to 80 tons per sq. in., with practically no ductility, according to its heat treatment. A microscopie examination, on the other hand, would show the structural composition of the steel, from which its physical properties could be approximately deduced. From this it will readily be understood that the microscope has played an important part in the development of modern rnetallurgy, and to-day it is in daily use for the examination of metals and alloys in the laboratories of most works dealing with the rnanufaeture and working of metals.THE IRON-IRON CARBIDE EQUILIBRIUMTo understand fully the mode of occurrcnce of the different constituents of a knowledge of the Iron-Iron Carbide equilibrium diagram (Fig. I) is essential to heat-treat steel successfully and to interpret microstructures correctly such a knowledge isabsolutely indispensable.A portion of the Iron-Iron Carbide Diagram, dealing with steels below 1000 and containing up to 1 carbon is given below.It should be noted that the diagram deals entirely with pure carbon steels, and does not indicate the influence of the usual so-ealled "impurities" present in all commereial carbon steels...

Jan 1, 1926

By Whiten W. J

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. In this way model parameters are obtained describing the behaviour of ball mills over a wide range of mill sizes and operating conditions. These parameters define the flow and breakage of each size fraction of ore in the mill. Flow of coarse particles through the mill is found to depend on the proportion of coarse particles present. The breakage rates of coarse particles are found to decrease markedly with mill diameter for mills over 3 m in diameter.Simulation of grinding circuit throughput at constant productsizing for different mill diameters shows that throughput is proportional to theoretical mill power consumption for mills up to about 3 m in diameter. Thereafter the throughput gradually falls below that indicated by power consumption, the decrease becoming quite significant for large diameter mills. Simple qualitative physical arguments are presented to explain this behaviour. The models developed have applications to ball mill scale up. Work on their further development is continuing.

Jan 1, 1982

The direction taken by mineral processing in the next 20 years will be determined by sharing of Australia's resources to fill world needs; by the low energy costs in Australia; by environmental considerations; and by Re- search and Development contributions. Examples of the interplay of these factors are given by consideration of eight minerals.

Jan 1, 1981

Numerical modelling is a valuable tool for simulating the fundamental processes that take place during a heating. The models presented in this paper have enabled a quantitative assessment of the effects of initial pile temperature, pile size and mass and coal particle size on the development of a heating. All of these parameters have a certain criticality in the coal self-heating process.

Jan 1, 2005

The paper presents two methods for periodical identification of the dependence between haulage speed and loading torque of the shearer for periodical corrections of control algorithms. These algorithms are useful for working with small microprocessor-based systems. The paper is concluded with results of identification using above methodsand with discussion about their merits and demerits. The longwall mining system is the basic exploita-tion system used in coal mining in Poland. The quantity of coal produced by this system, using a shearer loader as a cutter-loader machine is esti-mated at 170 million tones per year. For this rea-son scientific research concerning these machines is of major practical significance.

Jan 1, 1985

This paper considers the opportunities and problems which in-situ leach mining technology presents to the mining industry. These are exemplified by concerns addressed in the development of a proposal to mine uranium by in-situ leach techniques at Beverley in South Australia.

Jan 1, 1988