Search Documents

By Palmer DJ, Bain JH, Pullen JB

Over the last ten years at Risdon, zinc production capacity has almost doubled. This has resulted in modifications, many of which have affected zinc deposition operating conditions in the cells. Some of these changes appeared to have affected average current efficiency to such an extent that a special investigation was initiated, using multiple regression analysis to assess historic cell unit operating para- meters. The study highlighted the importance of certain parameters in maintaining maximum current efficiency for zinc deposition from !Risdon purified solutions under conditions of !changing current density, acidity and zinc con- centrations. Maximum current efficiency was obtained only within a zinc to acid ratio in cell electrolyte of 0.45 - 0.55 and a residual zinc concentration greater than 48 g.1-1, irrespective of actual zinc concentration or The investigation also established: ieters giving minimum power consumption at termined current density; the effect of ntration changes in common impurities on nt efficiency; the existence of high s of some impurities in solids precipit- in the cells and pure solution tanks.

Jan 1, 1975

Obvious differences in mineral deposit types occurring in Outer Melanesia and Northern Chile can be related to the sub- marine-dominated nature of volcanism in the' former area and the subaerial-dominated nature in the latter area. Subtle variations in subvolcanic epithermal-porphyry ore systems between the two areas probably result from differing ore fluid compositions. Hydrother- mal convection cells in Outer Melanesia will be seawater-dominated, consequently rela- tively high salinities and chlorine contents will characterise the ore solutions. Trans- portation of metals as chloride complexes is likely and the ease of seawater sulphate reduction to sulphide in the ore systems will lead to widespread, sparse dissemination of sulphide minerals. Relatively low grade por- phyry copper deposits will typify these ore systems. In Northern Chile hydrothermal convection cells will usually be dominated by meteoric waters. Consequently ore fluid salinities are likely to be lower and chlorine will be less abundant. Under these circum- stances transport of ore metals as bisulphide complexes could be important. Boiling and loss of H2S gas from these fluids would lead to rapid precipitation of metals and higher grade deposits. Erosion rate is a very important factor in the preservation of ore deposits and this may be the major control on the richness of a metallogenic province. The abundance of mineral deposits in the El Salvador region of Northern Chile compared to Fiji is probably a function of the much lower rates of erosion in the former area.

Jan 1, 1987

Mining projects draw together stakeholders with various degrees of experience in managing and assessing financial risk. When this risk is not fully appreciated or quantified, the potential for making decisions not suited to investor requirements is significantly increased. A feasibility study provides key information on project development potential, requiring detailed technical investigations with thorough financial analysis. Centaur Mining and Exploration (CME) owned and operated Cawse Nickel Operations (CNO), one of three Australian projects to develop and process vast amounts of near surface nickel resources. A technical ædue-diligenceÆ and æbankable feasibility studyÆ confirmed the large resource base, newly applied yet tested technology and relatively low unit costs would produce nickel in the lower half of industry operating costs. A number of production variables including capital requirements, delayed start-up, nickel grade, processing, maintenance and product output were outside the feasibility estimate. This was combined with exchange rate fluctuations and lower Ni prices. The inability to generate adequate cash flow and service debt repayments ultimately led to receivership and liquidation of all assets. Following the sale of CentaurÆs gold and nickel divisions, $A 784 million remained outstanding to creditors. This paper aims to define key issues leading to CNOÆs collapse by reviewing feasibility parameters, valuation methodology and project development. Some methods of assessing project viability are discussed with the aim of increasing stakeholder risk awareness.

Jan 1, 2003

By R J. Everett

The mining industry is beginning to adopt quality systems based on the requirements of International Standards for quality assurance, such as the ISO 9000 series. Indications from similar industries are that considerable benefits are to be had from their adoption. This paper describes the use of the International Standard ISO 9001 for quality assurance within BUKA Minerals Limited. This provided guidance for the development of a clear statement providing agreement on the processes to be followed and the outputs required when dealing with outside service providers. Discussion focuses on the interaction with BUKAÆs consultants and contractors during the specification stage, resulting from the application of quality assurance techniques. Risk analysis was used to identify and manage the risks associated with the companyÆs contract for geotechnical and mine design services and the tender for a mine development program of work during the feasibility stage of the project. Setting acceptance controls for the deliverables from such contracts is traditionally fraught with difficulty. BUKA used Failure Mode and Effect Analysis for exposing underlying risks that were not effectively being countered. The briefs were reviewed and additional controls were developed to manage the risk. These controls have provided clearer instructions to the consultants and contractors, indicated audit points for the company and defined the deliverables. There exists within the company, and among its outside service providers, a clearer understanding of what is to be achieved and how it will be measured. The process has imparted considerable confidence to both parties on how the work will proceed and what outputs are to be provided. Some discussion is provided on how quality principles are being applied throughout industry and commerce, generally, and how they may apply to the mining industry. The paper argues that, far from being an appendix to the tendering process, Risk Management should be a mandatory step integrated into the definitions of the work.

Jan 1, 1998

The impact of computers on the mining industry has increased for the past twenty years in most parts of the world. The application of computers in the mining industry has been demonstrated in areas such as geological data analysis, ore reserve estimation, mine planning, and manpower training. There is also a general concern in this country regarding the computing background of graduating mining engineers from the Australian higher institutions of learning. This paper describes specific steps which have been taken at the Department of Civil and Mining Engineering, The University of Wollongong to provide adequate computing background to mining engineering graduates. Specific topics discussed include hardware and software available to students and how "computers" have been integrated into the mining engineering course.

Jan 1, 1986

In the late-1990s, and into the 2000s, many industries, including the mining industry, have seen significant transaction activity by way of acquisitions, floats, joint ventures and major capital projects. The fundamental financial trends are two-fold. First and foremost, a high level of transaction activity within the industry and secondly, the recently introduced requirement for corporate governance standards, have placed increasing pressure on the directors of mining companies. This paper will deal with specifically corporate governance implications of any large capital investment transaction and the associated impact on the mining industry. To provide the framework for this paper, I have looked at a number of recent transactions as well as corporate governance recommendations from the ASX and the HIH Royal Commission.

Jan 1, 2003

The main asset of a mining company is the mineral resource; without resources there is no mining business and the infrastructure is useless. In this context the role of the mining geologist is to always keep the resource inventory to an optimum level for the mining business and to maximise the transformation of the resources into reserves in a multi- disciplinary work environment. In short, a ægood mining geologist has to always provide the best ore to the millÆ.To do his/her work properly, several technical skills are needed: to know how to observe and describe nature in order to optimise the data acquisition process, particularly when mapping; to have a good understanding of natural variability in order to develop proper sampling strategies and sample preparation protocols to minimise all the errors generated by the sampling process; to have a good understanding of assaying practices: their limitations as well as their assaying errors; to carefully and properly store the geological data and information and to preserve the geological patrimony; to fully understand ore forming processes to generate the best possible geoscientific models, which are fundamental for the mining business; to fully understand the consequences of the geoscientific models along the value chain from rock to cathodes; and to continuously validate and improve geological practices and models by continuous data collection and observation of geo- mining-metallurgy processes. Some very important behavioural competencies are also needed:long-term vision, passion for excellence and value generation, strategic influence, systemic and innovative thinking, and knowledge and experience transfer. Last but not least, it is important to point out that a deep knowledge of the mining business is essential to add value by using geology best practices.

Jan 1, 2006

By R Nakia, R Livingstone

Historically the Goldfields of Victoria produced large volumes of gold. Interest in these historical Goldfields has grown over recent years with a view to restarting production of gold. A notable example of this is the Bendigo Goldfield. There is also interest in the Ballarat Goldfield and Ballarat Goldfields Ballarat East Project is a particular example of this. The aim of this paper is to describe the ventilation aspects of the potential Ballarat East project. The mine is proposed as a decline access. The paper gives an overview of the project and in particular the ventilation planning associated with a number of possible equipment scenarios. The paper also analyses the main ventilation pollutants that are likely within the proposed mine as it develops to increasing depth. An attempt is also made to determine the depth at which mine climate will become the dominant pollutant rather than diesel exhaust pollutants.

Jan 1, 2003

The quality of the external water source for a mineral processing plant may influence the extent to which the environmentally desirable practice of recycling of water from plant products is possible. This is particularly likely for froth flotation plants where the chemical quality of the water may affect the plantÆs performance. The quality of the external water source or the recycled water can be improved by a water treatment step, and in turn the extent of recycling which can be tolerated is able to be influenced. The quality of the external water can range from very high quality, soft water derived from melting snow, to poor quality, hard water (high levels of dissolved calcium and magnesium) from underground aquifers, and to even lower quality sea water (very high levels of dissolved species including sodium chloride). It can be noted that some underground water is more saline than ocean water as well as containing high levels of dissolved calcium and magnesium. Occasionally, a different source of water is utilised in the wet and the dry seasons. Increasingly, sewage water from cities is becoming a potential external water source with sustainability implications. If the initial quality of the external water is high, the scope for recycling of water from all the products is maximised. Such reuse or recycling of water from the products allows chemical species from oxidation of the ore and from other inputs to the process such as reagents to increase in concentration in the water returned to the plant. Such accumulation of species can have negative effects on the performance of a process such as froth flotation but instances of positive effects exist. Some reagents which are used in flotation plants such as lime or sodium carbonate also happen to be commonly used for independent water treatment plants. Hence, the flotation process may inadvertently provide some aspects of water processing. Where the quality of the water in the feed to a mineral processing plant (external water plus recycled water) is not an issue, more powerful solid-liquid separation processes can be considered to maximise the removal of water from the products and its reuse. Such processes may also have complementary benefits in a sustainable mineral industry by, for example, producing a tailing stream with a higher per cent solid value which is more suitable for safe storage on the surface or underground. This paper documents findings on the effect of water quality on the flotation process. It also considers current directions of change in the need for increased removal of water from plant products. It then considers the implications of these trends for maximisation of water recycling by such operations.

Jan 1, 2003

The paper describes major principals in hydrodynamic test- ing of horizontal and inclined boreholes using flowmetering and pressure build-up techniques while tunnelling and dri- ving permanent workings through water bearing rock and fau- lted zones. A number of case histories is given together with the description of technical means and special equip- ment.

Jan 1, 1988

A Master of Applied Science degree course in Mining Geomechanics commenced in 1983 at The University of New South Wales, taught by extern- al (correspondence) studies. The course is aimed at graduates employed in the mining indust- ry, and especially people involved in geomechan- ics projects on a routine basis in remote locations. This kind of course is unique in Australia and is one of only two correspondence programmes available at this University. The author designed the course and nursed it through the early years, and was Director until 1986. The paper describes the teaching and assess- ment methods and also discusses aspects of admin- istration and coordination of such a course. It is concluded that an important need of the mining industry is being catered for and it appears that similar correspondence course for- mats would also be useful in other areas of the minerals industry.

Jan 1, 1986

The paper presents an algorithm for calculating the natural air distribution in a ventilation network (sub-network) on the basis of following data: - for each network branch: labels of starting and ending nodes, label of the branch, resistance and natural depression; - for each fan: the characteristic in the form of a second order equation and initial flow.

Jan 1, 1977

By Conway KM

The traditional role of Australian Consultants in project development has been until recently restricted to the provision of discrete packages for survey and engineering services during the feasibility, design and construction phases of a project. Management of such projects was the province of the owner/developer or his agent. However, Australian Consultants are now being con- sidered for an expanded role on resources Projects.

Jan 1, 1983

The general theme of the paper is a resume of factors which induce management to explore for oil, gas, coal and uranium in Australia. It is non-technical in the sense that apart from brief references exploration techniques are not covered. The central theme is the interplay of such diverse factors as taxation, mining 'regu- lations, exploration costs, availability of competent personnel, potential markets within and outside Australia, projected prices of sources of energy and their distortion by governmental action including restrictions on international trade for economic or political reasons, the role of the so-called multi- national companies, extreme views by pressure groups on the preservation of the environment, the availability of funds for exploration and the possible returns to the providers of exploration monies.

Jan 1, 1974

A programme began in 1970 to eliminate the charging of fine materials into the copper blast furnace of The Electrolytic Refining and Smelting Company of Australia Ltd. at Port Kembla, N.S.W. A disc pelletiser and drying plant has been installed as part of this programme. Feed material for the plant is a blended mixture of copper concentrates, fine copper-bearing residues, and blast furnace cyclone dust. The operating parameters for the disc have been calculated by comparing the perform- ance of three other discs on the plant. Re- search work on choice of binder, feed moisture and drying conditions has led to the production of reasonably high strength pellets. A description of the pellet plant and modifications necessary to overcome the initial performance problems is given.

Jan 1, 1974

A good blending system is one that ensures that a plant can cope with the amount of grade variation that it will encounter. Prediction of amounts of variation that will be encountered on time or tonnage scales that are important should be regarded as an essential part of the planning of mines and plants. In some cases, the natural amount of grade variation when ore is mined and handled in the cheapest way will be acceptable. In other cases, it is necessary to understand the effects that various ore-handling processes have on amounts of grade variation at various scales and to design a blending system with considerable care. Blending tends to matter more when plants are sensitive to many aspects of grade. It can be very difficult to find the best compromise between capital cost and the amount of grade variation. In these cases it is important that ore blending options be considered carefully as part of the planning of mines and plants. Failure to make plans that consider likely amounts of variation can be very expensive.

Mar 1, 2010

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

Away from past controversial presentations, a matter of fact, intuitive and simplified approach to the Theory of Sampling (TOS) sampling variance prediction formula is offered which gives an insight on the type of model required for the liberation factor, the practical limitations of such model and methodological principles for its calibration. This paper intends to see what happens in TOS when trying to go from the very simple towards the full level of real life complexity, and actually tries to answer the question: Is there such a thing as a æsimpleÆ TOS?

Jan 1, 2005

Selection of the mining method and most appropriate mine layout for deep open cut coal mines is discussed, giving particular attention to the types of mines expected to be developed in the future in Australia. Because of the more complex nature of these operations a large number of alternatives for mine design are available, and the constraints associated with these designs are discussed. Potential problems to be overcome are identified to allow setting of realistic targets for maximum output and build-up production rates.

Jan 1, 1981

The development of metallurgical training is briefly reviewed. The reasons for the current trend for Metallurgy Schools to become Schools of Materials Engineering or Materials Science are mentioned as is the role of Departments of Chemical Engineering in the teaching of extraction metallurgy. Some problems on academic staff recruit- ment are highlighted and predictions concerning future difficulties in industry getting adequately trained professional staff are made. The need for a special effort to attract and retain the best undergraduate students is put Forward.

Jan 1, 1987