Search Documents

By A M. Robertson, R Lefebvre

Air movement and associated oxygen transport through waste rock dumps has the potential to significantly enhance the rate of oxidation of pyrite-bearing material. While this is a desired outcome for most heap leach operations, airflow in waste rock storage facilities can result in significant increases in generation and acceleration of acid rock drainage. Hence, a good understanding of internal airflow through waste rock dumps is required to control ARD and minimise any associated liability. The principal mechanisms contributing to airflow and oxygen transport in a waste rock pile include: diffusion; advection due to a thermal gradient (chimney effect) and/or wind pressure gradients; and advection due to barometric pumping. While diffusion is typically limited to a near-surface zone of a few meters depth, advection and barometric pumping have the potential to move air (and oxygen) to much greater depths into the pile. In general, the more permeable the waste rock material, and the greater the height-to-width ratio of the waste rock pile, the greater is the potential for advective air movement. The reactivity of the waste rock material as well as the coarseness (hence air permeability), and the spatial variability of these properties within a pile, have a strong influence on the magnitude of thermally induced advection. In contrast, air movement due to barometric pumping is controlled by the waste rock porosity, changes in ambient air pressure and the heterogeneity of air permeability of the waste rock dump. Results of field monitoring and numerical modelling using TOUGH AMD are presented to illustrate the concepts on air movement in waste rock piles discussed in this paper. During the design and construction phase, airflow can be controlled by judicious placement of reactive waste rock and use of selective placement techniques to control the internal structure of the waste rock facility (eg introduction of horizontal layering, prevention of inclined, high-permeability, channels (æchimneysÆ)). Several closure measures are available to minimise airflow including: placement of a low-permeability cover to reduce air entry; and placement of a non-reactive cover material to isolate reactive material from the zone of active airflow and/or regrading of the waste rock pile to obtain a geometry and internal structure less susceptible to advective airflow.

Jan 1, 2003

By Laajalehto K

The basic condition necessary for flotation is hydrophobicity of the surface of the mineral to be floated. For sulphides, this condition usually requires treatment with a collector solution. The conditions for this treatment have until recently usually been chosen by the trial and error principle which has indeed been working relatively well under favourable conditions; ie for simple homogeneous ores. However, the present tendency to increasing use of complex and often relatively lean ores sets increasing requirements for the control of the flotation process. This development is the reason for the present rapid development of process control methods in flotation. In addition to the already well-established practices of pH and reagent feed controls, the importance of measuring and controlling the electrochemical potential of the ore particles to be floated is recognised in the case of sufficiently conductive minerals. In fact, the electrochemical potential seems to be the basic quantity determining the flotation behaviour of such relatively well-conducting minerals as sulphides. Since the hydrophobicity of the mineral and, hence, its flotation properties are ultimately determined by the composition and structure of its surface, information on these under different process conditions is important for design and operation of efficient flotation processes. The basic requirement set for the methods used for obtaining this information is high surface sensitivity of the method. The recent rapid development of surface characterisation has produced several methods which fulfil this requirement. Their application to the problem of characterising surfaces of mineral samples in contact with collector solution is, however, often complicated. The main reason for this is the vacuum environment necessary for the measurement. In the case of flotation experiments this means that in most of these methods the measurement cannot be made in situ, but the sample must be extracted from the liquid and subsequently evacuated in the vacuum chamber of the instrument. It is essential to carry out these steps so as to avoid to the extent possible changes in the sample surface. For the purpose of establishing whether this has been accomplished it is important to compare the results of methods operating in vacuum with some available in situ method. An optimal choice of methods seems therefore to be a combination of the available powerful vacuum methods with in situ measurements. The most usual combination seems to be X-ray photoelectron spectroscopy (XPS or ESCA), Fourier transform infrared spectroscopy (FTIR) and electrochemical measurements. This choice combines the unique possibilities for direct elemental and chemical characterisation offered by XPS (Cecile, 1985) with the in situ capability of FTIR and electrochemistry. In the XPS measurements, it is essential to apply a special sample handling technique to avoid loss or damage of some sensitive species of the collector-based layer on the mineral surface. In the following will be given some examples of the application of the XPS technique in combination with electrochemical methods of sample treatment to studies of the layer formed on sulphide substrates in ethyl xanthate (EX)

Jan 1, 1993

By B McIntosh

Sustainability in its simplest assessment has been defined as æmeeting the needs of the present without jeopardising the needs of future generationsÆ. For the mining industry alone, this statement could indeed be interpreted by the many cynics in our community as an oxymoron; as miningÆs very existence requires the extraction and consumption of finite resources. However for the future of industry as a whole, the integration of mining, minerals processing and manufacturing presents us with a unique opportunity to achieve sustainability through the continued supply of metals and materials for society, in a manner which can achieve positive social outcomes through a triple bottom line approach.The Kwinana Industrial Area has been Western AustraliaÆs premier heavy industrial precinct for more than 40 years and its prevailing level of prosperity will ensure it remains a significant contributor to the State economy through the 21st century.The Kwinana industries depend on each other for the production of essential raw materials vital to their manufacturing and refining process, an innovation that also has significant environmental benefits.Formed in 1991, the Kwinana Industries Council strives to foster positive interaction between member companies and with the local community.The aims are:to co-ordinate the activities of Kwinana industries on a range of common issues; provide effective liaison with the local community; promote a positive image of Kwinana industries; highlight contributions to the community by Kwinana industries; and work towards the long-term viability of the Kwinana Industrial Area. The Kwinana Industries Council facilities these aims by focusing on developing and employing leading edge technology, giving workplace health, safety and environment top priority, and taking a committed, responsible and pro-active approach to environmental protection, whilst forging a two-way partnership with the local community.The sustainability of industry is the key objective for the Kwinana Industries Council and through the involvement of the 13 member companies industry strives to:achieve efficient processing of resources to provide a range of goods and services needed by the community; achieve acceptable and decreasing level of environmental impact; provide jobs and income for our community; and engage co-operative projects that benefit the local communities, the State and Australia.

Jan 1, 2004

By Morrison J

Considerable confusion is to be found in the methods of estimating mineral reserves. The solution appears to be more cooperation between industry and government to agree upon a classification system with guidelines to overcome the problem of the many variable factors affecting reserves. The classification system proposed by the United States Bureau of Mines and the United States Geological Survey (USBM/USGS) together with the guidelines similar to those suggested by the Australasian Institute of Mining and Metallurgy/Australian Mining Industry Council (AusIMM/AMIC) is recommended for reporting mineral reserves to government.

Jan 1, 1979

An algorithm is described which leads directly to a unique set of coal washing parameters which, in two or more parallel streams, will give maximum yield of product at a given ash. This occurs when all parallel streams are washed to the same incremental ash. This strategy is shown to offer a considerable increase in yield compared to the simpler strategy of washing each stream to the same sumulative ash.

Jan 1, 1987

After many years of studying the rock mass gravitational flow phenomenon, it is well known that moisture conditions may change the mechanical properties of the caved and broken material, causing different problems at drawpoints. One specific problem, perhaps one of the most unpredictable and uncontrollable, is that of mudflows (also known as mud rushes). The aim of this paper is to show how to establish optimal extraction rates at a drawpoint in order to avoid the closure of that drawpoint due to the high risk associated with having high-technology automated loaders working in the production level of panel cave and block cave mines prone to mud flow events. This optimisation should take into consideration critical restrictions related to mine planning, such as the need to reach the planned production. It is also important to consider the correct design of surface (in the subsidence zone) and underground drainage systems to prevent groundwater or rainwater entering muck piles, filled stopes, galleries or open cuts. With these considerations, and keeping in mind other factors that should be included in a sensitivity analysis of variables, it is possible to find a correlation between the percentage of extraction from a drawpoint and the possibility of occurrence of a mudflow. Finally, this paper proposes different draw strategy techniques in order to mitigate potential mudflow issues on a caving production level.

Sep 26, 2011

By Tomlinson R. C

The paper will briefly describe planning in the National Coal Board (NCB) and the contribution that operational research makes to it. It will then give details of some of the models in use and will finally consider critically the problems of looking ahead to the next century.

Jan 1, 1977

The paper reviews recent valuations of mineral properties, many of which are at an early stage of exploration. The various methods used are outlined. The problem of comparing, in terms of whether it is fair and reasonable, a highly subjective opinion of the present value of a portfolio of exploration tenements with a vendor consideration, the real value of which, in most cases, lies at some indeterminate time in the future because of the application by the Australian Stock Exchange (ASX) of escrow conditions, is highlighted. Examples are given of some of the questionable logic used by consultants in handling this difficult issue. A proposal for revision to current flotation and listing practice which, the author believes, would circumvent the problem and at the same time provide better protection for the investing public is offered for Consideration.

Jan 1, 1994

The efficiency with which it is expected that a particular coal may be burnt in a power station boiler significantly affects the value of the coal. Consequently many laboratory tests have been developed to provide data on the combustibility of coal. Computer modelling of coal combustion has also provided insight into limits on coal burn- out. Such modelling suggests that burnout of bituminous coal in a power station boiler will be strongly influenced by physical limits on the diffusion of oxygen to the individual coal particles. Coal chemical reactivity appears to be relatively less important. As a consequence of the diffusional limits, significant improvement in burnout is achieved either by producing less large p.f. particles or by providing sufficient furnace residence time to burn the large particles. Field data from a variety of power stations supports these cn.clusions. Burnout was also found to correlate well with volatile content for a number of coals from widely different sources. This is expected as the high vola- tile coals produce less residual char to be burned by the relatively slow heterogeneous Combustion.

Jan 1, 1987

By Boehme PW, Gregory OR

The results presented here show quite definitely that in the system investigated the intensity of dispersion is enhanced by switching the flow entry from bottom to sides of the packed trough. Since there is no reason to suppose that this would not be true generally then it is not surprising that the blast furnace dispersion data of Standish and Polthier lie above the data for packed columns with bottom fluid entry. In fact, on the basis of the present results, blast furnace dispersion results can never equal standard packed column behaviour but must always be above these. The result that the intensity of dispersion in the trough model is higher closer to the side ports than away from them is at variance with that of Standish and Polthier blast furnace results. Aside from the obvious structural differences between these two systems, it is thought that the presence of raceways and the tortuous path of the gas flow in the furnace may provide an answer. Clearly this is an important difference in the behaviour of the two systems and further investigations designed to clarify the position would have significant practical value. This would also give an indication of how the furnace D/ud values may be decreased along the whole height - assuming of course that this result gives the best overall performance of the furnace. However, there is to date no knowledge whatsoever about this aspect of blast furnace Technology.

Jan 1, 1975

Edie Creek is located in the Morobe Goldfield about 17km by road from Wau in the Morobe Province of Papua New Guinea (PNG). Four distinct periods of mining development have occurred since discovery of rich alluvials in 1926. During the two years following discovery, individual expat-riate miners with gangs of native labourers mining rich alluvial gravels dominated the field. After the discov-ery of hardrock mineralisation in 1927, companies accumulated leases and devel-oped extensive underground mines and mechanical processing plants at Day Dawn Mine and Edie Creek/Karuka Mine between 1929 and 1942. After the Second World War, the underground operations were not re-opened, and mining activ-ities mostly concentrated on working alluvial and eluvial deposits. From 1962 onwards, Papua New Guinean miners became increasing producers as company activities declined. In 1990, Edie Creek Mining Company Pty Limited, a joint venture company involving Wau landowner groups commenced operations on New Guinea Goldfield's leases. It currently mines by open pit methods, rich quartz stringers and is invest-igating the open pitting of the Edie Creek/Karuka underground workings.This paper describes the mining and processing techniques employed during the various phases of develop-ment at Edie Creek in the past 70 years. The problems and hardships of operating on a new and remote goldfield are outlined.Abstract

Jan 1, 1994

By Ren T. X, Jozefowicz R

In many branches of engineering, there has to be an understanding of the motion of fluids in order to solve problems. Many safety and health problems in the mining industry are typical examples that involve the understanding and analysis of fluid flow, such as explosions, the spread of fires, dispersion of gas and dust, and ventilation patterns. Computational Fluid Dynamics (CFD) is concerned with the use of computers to produce information about the ways in which fluids flow in given situations. Until recently CFD has been widely applied to a variety of industrial sectors and increasingly to problems in the health and safety areas. With the arrival of more powerful computers and CFD packages, CFD techniques are no longer practised solely in a research environment, but can be used by engineers in many industrial fields. This paper introduces the basic concepts and general procedures involved in the use of CFD technology. A comparison is given as a guide to the major features of a number of widely used commercial CFD codes. Areas of potential CFD applications are identified in a range of safety and health problems in mining industry. An example is presented to illustrate the use of this technology. It is believed that the exploitation of these areas using CFD approach will contribute significantly to the solution of today's many mine health and safety problems.

Jan 1, 1995

By J M. Wang, Q M. Hao

A mathematical model is set up to solve the problem of optimal design of the production scheduling on exacting open pit mine. At the same time, the establishment of model in operation condition and its solution are considered completely. It gives not only algorithm of optimal design but also strict mathematical argumentation in the process of optimal design.

Jan 1, 2003

A report is given of the problems of finance and physical resources that currently affect The University of New South Wales, and of some of the measures adopted to alleviate them. Partly as' a result of review procedures, a School of Mines was formed to amalgamate Applied Geology and Mining Engineering, and to add the skills of extractive metallurgy to produce a group to match the needs of the minerals industry. A review of courses within the School indicated a need for enhanced computer teaching, which is partially negated by a lack of resources. It also shows an overcrowded course whose structure could possibly benefit from a split into managerial and specialist streams.

Jan 1, 1986

This paper details the approach adopted to develop an integrated asset management system for a GreenfieldÆs Metallurgical Plant during a recently completed feasibility study. The proposed asset management system deals with general aspects related to metallurgical operations and includes the following:plant operation and control, human resources, security systems, stores, and maintenance management. The paper deals with the establishment of requirements for the asset management system, the interfaces required, available systems in place and cost estimations for implementation. Every effort was made to integrate the system into existing corporate installations to create an integrated and effective management tool from both a plant operation and support perspective.

Jan 1, 2002

By I Ametov, G Levay

It is now common practice to use substantial amounts of recycled water in mineral processing plants to minimise both environmental discharge and withdrawal of fresh water from often limited water resources. Recycled water additions to process water are frequently obtained from sources such as tailings dams, tailings thickeners and concentrate dewatering. It has been suggested for some time that addition of recycled water to process water will impact the quality of the process water and that changes in water quality may influence flotation performance. To date, investigations of process water quality changes as a result of water recycling have been limited and as a consequence there are very few data available to substantiate these ideas. Thus the impact of recycling on process water quality remains largely unquantified. Over recent years we have conducted water quality studies at a number of mineral flotation plants with varying degrees of water recycle. This paper describes the results of these investigations, including data which suggest that build up of salinity due to recycling while it occurs, is reduced by fresh water make-up. The fate of flotation reagents such as collectors, promoters, frothers and flocculants during process water recycling has also been investigated. Results show that process water concentrations of these reagents vary from plant to plant, but that, with the exception of frothers, most reagents are generally removed from the system through mineral adsorption. In general, the results of these investigations suggest that recycling process water will not result in continuous increase in solute concentrations as appears to be the commonly held view.The effects of changing water quality on flotation can vary. In many cases, flotation conditions can be optimised to suit the water quality, while in others, treatment of the water may be necessary to obtain acceptable plant performance.

Jan 1, 2009

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003

By B Hooper

Deep cuts in CO2 emissions will be required to stabilise and, in the long term, decrease CO2 concentrations in the atmosphere. Technologies for capturing CO2 from major stationary sources (power stations, industrial plants, etc) and storing that CO2 for long periods of time is one of few near term options for decreasing CO2 emissions. This transition to low carbon intensity energy and possibly the hydrogen economy through renewables and in the long-term technological developments such as artificial photosynthesis.Capture of CO2 from post combustion emissions can be done using a range of technologies though costs are currently high and dependent on the concentration of CO2 in the emissions. Techniques include solvents, pressure swing adsorption and the use of membranes. Options for decreasing capture costs by increasing the concentration of CO2 in the emission stream include the use of oxyfuels (in pulverized fuel types boilers) and by moving to integrated gasification combined cycle (IGCC) operations either simply for power generation or for poly-generation opportunities. Once the CO2 has been captured it can be stored using a variety of methods. Storage in the ocean has been suggested but is considered an unlikely option because of environmental uncertainties and political opposition. Mineral storage is a niche opportunity. The greatest potential lies in geological storage of CO2 and this option is commanding increased attention from the Australian and international community.In Australia, the Cooperative Research Centre for Greenhouse Gas Technologies (CO2CRC) is an important new initiative that will support energy companies and energy intensive industries in meeting challenges posed by greenhouse gas issues and assist them in their efforts to reduce their emissions profile.The progress of geo-sequestration and the challenges in the capture and separation of CO2 in the process industries are discussed.

Jan 1, 2004

The introduction refers to observations made in the early days of the Nationalisation of the Coal Industry in the United Kingdom, indentifying the underground transportation problems. Statistical information is presented, highlighting the considerable developments which have been made in recent years with an evaluation of the manpower and cost involvement.

Jan 1, 1985

By J Meinhart, J Rodler, I Katolicky

The ever increasing number of vehicles is leading to slow-moving and even stationary traffic sitting longer in traffic jams over extensive city areas. This traffic situation causes a sharp increase in pollutant emissions from vehicles, and high levels of pollution usually result throughout the built-up area. Reducing the pollution level by using traffic routing measures to speed up the flow of traffic in the existing street network is only possible in exceptional cases.In many cases the only option for achieving a significant improvement in traffic conditions is to shift the traffic underground using a road tunnel or underpass. Such tunnel routes suck off the traffic from large sections of the city, thereby easing the overall traffic flow. Thus on the one hand it produces a sharp reduction in pollution levels in the area of the tunnel route, but on the other hand it can result in locally increased exhaust pollution levels from longer tunnel systems that require mechanical ventilation. The air extracted by the ventilation system is blown out into the atmosphere either directly through the tunnel portal, or via a venting tower. Pollution can therefore occur in the area surrounding such exhaust air outlets.Thus if a tunnel is planned in a city, then closer investigation is required of both aspects: the reduction in pollution in the area of the tunnel route thanks to relocating the traffic and easing congestion, and the increased short-range pollution around the tunnel portals (shafts).

Jan 1, 1999