Search Documents

By Robertson GE, McLaughlin JD

An extensive laboratory campaign was conducted to find a suitable water soluble collector to replace diphenylguanidine (DPG) in the matte separation process. The examination of the collectors was done by measuring the rate of flotation and the best candidate collectors were selected on the basis of the rate parameters. As a result of this search mercaptobenzothiazole (MBT) was selected for a plant trial. A plant trial of two weeks duration confirmed that MBT will produce separations at least as good as those obtained with DPG.

Jan 1, 1993

The Sydney Coalfield, Nova Scotia contains extensive undersea longwall mining operations which are expected to continue well into the 21st Century. A long term research program has been initiated by the Cape Breton Coal Research Laboratory to investigate the full spectrum of problems associated with undersea mining and develop specific guidelines for use by the mine operator. At present, research is centred on the detailed evaluation of existing undersea sub- sidence guidelines, the identification and development of instrumentation capable of moni- toring seafloor subsidence profiles and the effective sealing of offshore exploration boreholes. In addition, work is also planned to examine in situ strata permeability changes occurring between the mining horizon and seabed and the feasibility of using artificial islands.

Jan 1, 1986

A wide range of models are available to computer process simulators that require a large number of parameters which often are physical measurements, coefficients, calibration factors and functional forms. This makes it intuitively difficult in the majority of cases, to tune the parameters in order to simulate a circuit in agreement with experimental results. Unit calibrators operating on the principle of least squares minimisation of the difference between predicted and observed plant data, are relatively successful when the parameters are unconstrained and independent of each other. In the case of constrained parameters, a set of carefully chosen transforms is presented which map the unconstrained variables being minimised into the constrained parameters required for the model. This technique has been used successfully with the Powell minimisation algorithm and it may also be applied to other unconstrained minimisation methods. Necessary model characteristics are discussed to enable these transforms to be applied to interdependent model parameters such as points of a graph. Examples of the calibration of several unit models using these transforms are presented. KEYWORDS: Calibration, optimisation, transforms, process simulation.

Jan 1, 1993

By M Fisher, P Bradley, D Rogers

New England Antimony Mines has operated the Hillgrove Gold Plant at Hillgrove in New South Wales since 1969, producing stibnite and arsenopyrite products by selective flotation. Gold is present in the ore as fine free gold, gold associated with stibnite and gold associated with arsenopyrite, with some ten to 20 per cent of the gold reporting to the antimony stream and 35 - 50 per cent reporting to the arsenopyrite stream. Opportunity to process the arsenopyrite concentrate for onsite recovery of the gold values to improve upon the ten per cent recovery achieved by conventional cyanidation was recognised and subject to comparison with biological oxidation, roasting, nitric acid oxidation, low temperature oxidation (Activox«) and conventional pressure oxidation. Following further testwork and a feasibility study, a 7500 tonnes per annum concentrate feed pressure oxidation autoclave circuit was constructed at Hillgrove and commissioned in October 1999. The plant has operated at the close to design capacity since commissioning whilst optimising various operational and metallurgical aspects. The last three years has seen the process achieve an overall gold recovery of greater than 90 per cent for oxidised concentrates.

Jan 1, 2002

Bulk mining and handling technologies have been affected in two ways by the soaring costs of oil products in recent years. Firstly, the substition of oil by coal, oil sands and oil shale demands the development of high-capacity mining and handling equipment, and secondly the rising fuel costs favour a trend away from cost-intensive heavy truck transport. To cope with the growing volumes of material in mining and handling, larger equip- ment units have to be designed. This tendency becomes apparent from the examples of the Hambach open pit mine in Germany, and the Port Kembla handling plant in Australia. A combination of the flexibility of heavy truck transport and the cost advantages of belt conveyors is achieved by the system of semi-mobile crushing installations described in this paper.

Jan 1, 1981

By B Wiggins, M Russell

Off-gas handling systems are a critical component of modern metallurgical furnaces and typically represent as much as 50 per cent of the total installed smelter capital cost. Inadequate off-gas system performance, due to insufficient exhaust flow or excess maintenance downtime, can present a serious process bottleneck and limit smelter production rate. Therefore, it is essential that the relevant performance issues are fully understood and considered in the design of these systems, particularly when combustibles produced within the furnace must be combusted or handled in the off-gas system. This paper examines the requirements, design issues, and conceptual design process for state-of-the-art postcombustion off-gas systems. The relevant design considerations of safety, environment, energy consumption, and maintenance are presented, and the relative importance of these key issues are compared and discussed. The benefits of using computational fluid dynamic (CFD) modeling in the design process at the conceptual design stage are also demonstrated. Finally, the design basis and performance of a recent Hatch-engineered system currently in operation is evaluated.

Jan 1, 2002

By H W. Scriba

The development and improvement of computer-based process simulation packages over the past 20 years has provided process engineers with a powerful tool to use in the design of complex metallurgical plants. The use of such modelling tools has enabled the design of process plants that minimise operating and capital costs whilst optimising plant efficiency and recovery. Almost every new project developed in the current market is underpinned by a simulation of the process. In line with engineering best practice this simulation should be based on laboratory/pilot plant test work results and sound assumptions. Any errors that are not identified in the development of the process simulation may have significant effects on the final design and operation of the processing plant. Developing a simulation of the process in a comprehensive, logical and auditable manner is thus essential in ensuring the simulation accurately represents the expected process plant behaviour. A methodology that ensures these requirements are met has been developed by SNC-Lavalin Australia and is described in this paper. The methodology includes the major review stages of data collection, model planning, model building and optimisation, model review, scenario testing and options development, and model reporting. All of these stages should incorporate comprehensive client interaction and review by a suitably qualified representative. In applying these methodologies SNC-Lavalin Australia ensures that the process simulation model developed can be confidently utilised in the design of the process plant, and in the estimation of operating and capital costs, whilst ensuring that engineering best practices are met.

Jan 1, 2008

The theme of the conference this year is diversification. One way to diversify is through acquisition. The principle underlying the winner's curse is that in competitive bidding situations where the value of the asset bid for is uncertain the winning bid will overstate the true value of the asset. The successful bidder is blessed with the winner's curse. What this paper will explore is to what extent this is true; how acquirers can avoid being blessed with the winners curse; and show how joint venture deal structures are used within the mining industry to avoid the winners curse.

Jan 1, 1996

The basic issues of education for the mineral industry which emerge from experience and from a study of relevant literature are presented with the object of promoting. discussion. The subject is considered primarily from the university point of view and relates more to the disciplines of mining and mineral processing than to geology or perhaps metall- urgy, but the conclusions have wider implic- ations. Continuing education, being the subject of a separate paper, is only briefly discussed. The important and particularly relevant training and industry role of the technician engineer and technician are not considered.

Jan 1, 1974

An approach to underground mining of shallow dipping, thick seam coal is proposed in broad outline. The method is based upon overhand slice and fill, with hydraulically emplaced washery refuse as the filling material. Likely fill behaviour and character- istics are discussed and likely problem/investigational/ research areas defined.

Jan 1, 1976

By R Farana

The future challenges in mining instrumentation, mainly on future intelligent mines, are to continue providing instruments with the highest level of reliability at the lowest possible cost, and also to take advantage of technology existing in other industries and to adapt it to the mining context. New wireless instruments (smart sensors, smart actuators, smart controllers) would also be very useful, as well as instruments fully adapted to the monitoring of large movements that are observed, in both underground and open pit mines. Mining instrumentation is found to various degrees in most mines, both open pit and underground. Smart mining instruments present a certain number of aspects specific to the environment in which the instruments are installed. Namely, the instruments can be installed either for short-term or long-term purposes. The mining industry is always looking for useful instruments that can provide relevant information on ground behaviour adjacent to mining stopes or permanent infrastructure. The instruments must meet the various criteria, and must also evolve with the new mining technologies that are continuously being implemented. A strong collaboration between the mining industry, research organisations, and instrument manufacturers is the key to meeting these objectives. This contribution describes the current trends on smart sensors and smart instrumentation with Wireless LAN support.

Jan 1, 2003

By J Hunt

A critical aspect of geometallurgy is quantifying mineralogical and textural relationships that affect mineral processing (eg, liberation and recovery). However, to date, this has been an expensive and time consuming venture and only minimal amounts of this type of data are typically available to be included in the mine planning process. Our research is focused on developing methods that will produce the required mineralogical and textural data rapidly and inexpensively. New methods of characterising liberation potential from image analysis of coarse particulate material and direct small-scale flotation measurement are compared with measurement of liberation at final grind size (ie conventional tests on MLA). The new tests are designed to rank the liberation potential of samples in order to classify an ore deposit into domains of low, medium and high liberation potential. This parameter can then be used to adjust the cutoff used to differentiate ore from waste. Results to date show that all tests provide the same ranking for the samples. The measurement based on coarse particulate material compares favourably to the results from MLA analyses on the same samples. Further work is being carried out to determine which of the tests will be the most effective in terms of time, effort and cost

Sep 5, 2011

By Bowdler RJ, Lowson RT, Sarbutt JV

There have been few long-term studies of sulphide oxidation under controlled conditions. The object of this study was to investigate the oxidation and leaching characteristics of pyritic mine material under conditions that were commensurate with field conditions but which could be controlled and monitored on a long term basis. The test material - overburden from Woodlawn Mines Pty Ltd - was packed into a 300 cm high column and leached with water at an infiltration rate of 256 mm y-1 for 5 years. Chemical conditions within the column were continuously monitored by sensors embedded in the overburden and leachate from the base of the column was analysed weekly. The study examined the relationships between heavy metal release and gas, moisture, and chemical conditions in the column.

Jan 1, 1988

Segregation of granular material is a very common phenomenon. Realised in a forced manner it is a basis of all separation processes in mineral processing, mainly classification and beneficiation. Spontaneous segregation, occurring under dynamic conditions and making possible mutual translocations of grains, is however an undesired phenomenon as a rule. It decreases the degree of blending of the material which in many cases is an important technological feature of the material. It should be noted that the segregation can be treated as the reverse phenomenon to blending. The importance and frequency of spontaneous segregation has caused many rules and technical solutions to be developed aimed at decreasing the possibility of the spontaneous segregation. However, not enough attention has been focused on an quantitative description of the phenomenon of segregation, either to ways of quantitatively evaluating segregation effects or to explanation of the influence of conditions under which the grained material exists on the occurrence of segregation and its degree. The paper presents the following topics: 1. new numerical indicator for evaluation of the segregation degree (and blending) of material contained in an arbitrary determined region is proposed; it is determined relative to the maximum possible degree of segregation of the given material when taking into account its individual properties; values of the indicator can be calculated effectively for an arbitrary material, also for ulticomponent material. 2. there is proposed a way of evaluating the state of segregation (or blending) of material in an arbitrary part of the region mentioned above, based on investigation of the gradient of distribution of the material features; algorithms of analytical procedures and calculations are presented for typical cases met in mineral processing; 3. results of initial experimental studies, both laboratory and industrial, concerning the effect of the chosen factors occurring in transport and storage of the material on its degree of segregation are presented; and 4. conclusions referring to the fundamental and practical significance of the results are also presented.

Jan 1, 1993

This paper has been prepared to challenge the thinking of new leaders entering the mining industry in two areas. First, what is the worldÆs perception of mining and what does this mean to those entering the industry? Second, what is the future of learning in the mining industry and how can the industry attract and retain the best people?Then in closing, how can mining companies turn these challenges into opportunities and specifically how is BHP Billiton meeting these challenges.

Jan 1, 2004

The Broken Hill orebodies have 'traditionally been mined by cut and fill trethods. In the mid-1950's New Broken Hill Consolidated Limited experimented with sublevel longhole open stoping but did not pursue the method due to inefficient loading and poor fragmentation. The introduction of longhole open stoping in 1968 was a radical change and was necessary to enable the profitable extraction of lower grade orebodies and this method is now used for 55% of the production from The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines.

Jan 1, 1982

By C R. Headley, S O. Hille, N P. Jacob

The redevelopment of the Telfer Gold Mine in the Pilbara region of Western Australia was primarily based on the construction of a 17 Mtpa dual train concentrator coupled with open pit and underground mining operations. The unique copper-gold orebody at Telfer requires the application of complex flotation conditions normally reserved for base metal concentrators, where two competing minerals are managed into separate products. This paper describes the commissioning of the flotation circuit, the process modes and the master/slave relationship that flotation has with a variable orebody.

Jan 1, 2007

Since 1865 when Congress moved to create a Federal Mining Bureau, successive legislations have given rise to the current '!Federal Coal Mine Health and Safety Act, 1969. Coal beds from 22 feet to 20 feet thick are mined under covers from 50 to 2800 feet with full and partial pillar recovery equally popular and accounting for a total of 54% of the mines. Pillar recovery and roof support practices vary, and each operator must submit an overall roof control plan (within specific guidelines) for approval before undertaking any development. The guidelines relate to dimensions of openings, details of support, sequence of extraction, limits of extraction and caving details. Experienced and professional staff of M.E.S.A. provide roof control plans and make inspections and grant-approvals of principles of support and minimum support in pillar extraction, with provision for modifications with time. Guidance is given with training programmes and standards of supervision. All of these aspects are approached in the spirit of the Congress declaration that the first priority and concern must be the health and safety of the miner.

Jan 1, 1974

By A Ruotsalainen

Mining industry sees a comprehensive future in optimisation and process control. High resource utilisation is a starting platform when lower operational costs with higher rate of return are the target. Simulation is quickly penetrating the mining industry as a planning tool. A discrete event simulation helps to visualise the reality of a mine and the various mining processes, which typically include a fair degree of complexity. What-if scenarios can help to determine the impact of occurring changes to production. Understanding of critical points in the layout and resource allocation at an early stage can help to optimise the material flow. The obtained information may then be used as proposal or confirmation of the system applicability and economy. Simulation is a way to fine-tune and optimise the resources within. It helps to predict system sensitivity to various aspects. Although simulation today is used typically in a feasibility stage, there is an opportunity to continue using simulation for further process enhancement. In the future simulation will without doubt be used increasingly as a dynamic simulation and continuous improvement tool. This paper discusses the use of OptimineÖ simulation tool in resource optimisation. Some examples describe the way the tool operates and how it helps to view the technology, mine layout and operational data.

Jan 1, 2003

Over the last 15 years working in the mining, construction and extractive industries, one of the areas that has always concerned and at the same time drawn the author to it is the application of drilling and blasting in the underground development mining and civil construction tunnelling fields. In that time, the author has come across many drives and tunnels that are larger than design or badly damaged in the perimeter or both. When the question is asked as to why this is the case, the reply is generally æthatÆs the way it is and always has beenÆ. Sometimes it is blamed on bad ground, bad drilling, bad explosives, bad initiation or just plain bad. Most operators build a dilution factor into development and tunneling costs as an acceptance of overbreak and similarly pattern bolt everything to overcome excessive perimeter damage. This paper will attempt to unravel some of the mysteries behind perimeter drilling and blasting in underground drives and tunnels and discuss methods to reduce overbreak and therefore reduce costly dilution and to minimise perimeter damage which in turn will allow more cost-effective ground support. It should not be assumed that better drilling and blasting alone would automatically allow an operation to reduce ground support. The operator must still æreadÆ the ground and its characteristics in order to ensure sufficient ground support is placed to allow the operation to progress safely. This paper will not go into the intricacies of bolting, meshing, shotcreting, concreting and other ground support, but it will use indicative costs for the primary areas of drilling, explosives, excavation and labor to show the magnitude of cost-efficiencies which can be obtained through improved drilling and blasting applications. Drill and blast remains the most flexible and cost-effective method of underground excavation as long as it is applied safely and effectively.

Jan 1, 1999