Search Documents

Kinetics of bubble-particle interaction, surface hydrophobicity and interfacial phenomena in sulfide mineral flotation are discussed in this paper. Results of the measurements of a bubble and mineral induction time (IT) and detachment force (DF), vacuum of bubble evolution (VE) and mineral floatability are discussed for pyrite, galena, chalcocite and chalcopyrite. Natural wetting and wetting induced by xanthates with different lengths of alkyl chains are examined. Experiments show the existence of several maxima of hydrophobicity on dependences of pH and electrochemical potential. These maxima are attributed as the reflection of mineral surface heterogeneity due to xanthate adsorption and the presence of cationic and anionic centres with uncompensated positive and negative charges. These charges can be neutralised by both regulation pH and applied potential. The aim of this paper is to evaluate a thickness of the rupturing film and to estimate how long the bubble-mineral interactions are according to the experimental values of IT, in order to develop a procedure for comparing of the results of DF and atomic force measurements in the same dimensionality, and to compare the results of the experimental studies on the wettability of sulfides with those predicted by the models of physics of capillarity.

Jan 1, 2005

Blasting effectiveness must be gauged by total production costs. ANFO charges made up in polythene "sausages" are not as profitable as is indicated by the price of ANFO. All-slurry charges are warranted only where blastholes cannot be dewatered effectively, or where drilling costs are very high. An increase in blasthole diameter leads to coarser fragmentation. This effect is most pronounced in tough and massive or blocky strata, or in ground which consists of unfissured boulders in a softer matrix. When ANFO and some slurry-type charges of small diameter are used in plastic-acting ground, charges may fail to detonate through precompression by charges fired on an earlier delay. The optimum blasthole length is rarely less than four times the burden distance. For best results, blastholes should be inclined to the vertical and parallel to the face. Nominal burdens and spacings are often altered radically by the initiation sequence. For best fragmentation, all blastholes must have good effective faces, and should be effectively stagg- ered with an actual spacing:burden ratio in the approximate range 2.0-5.0.

Jan 1, 1975

Rock bolting provides a supplement or alternative to conventional timber and steel supports. The tensile strength of the bolts lies within a range established by manufacturing quality control. Rock bolt testing determines the ability of the rock, anchor and individual bolt as an assembly to accept load. The.test is performed to the yield strength of the bolt or anchor and deflection is observed. The anchorage index, inches deflection per 1000 lb load increment, is a measure of anchorage quality. This allows comparison with anchorages under ideal conditions. It also permits comparative assessment of roof bolt anchors in a particular environment.

Jan 1, 1971

In-stope long hole drilling (face parallel drilling) is a new technology currently being applied to shallow dipping (

Jan 1, 2003

An international raw material partnership, a $164 million 900,000 long ton per year aluxAna plant; an ideal location at Gladstone, Queensland, Australia - this is Queensland Alumina Limited, on stream in 1967 expanded 50 per cent by the end of 1968. Queensland Alumina Limited is the world¦s most modern alumina refining operation which is owned by an international consortium of four companies; Kaiser Aluminum & Chemical Corporation of the United States with 52 per cent; Alcan Aluminium of Canada with 20 per cent; Pechiney of France with 20 per cent; Conzinc Rio Tinto of Australia, 8 per cent. Q.A.L. operates as a co-operative -- the partners do not draw profits from the venture. Instead, each member of the consortium draws alumina in proportion to his share of the ownership. The method of disposal of this alumina is for the partner to decide.

Jan 1, 1969

In the mining and minerals industry, development, introduction and construction of new plant designs, to meet sustainability objectives, face a series of major hurdles. Typical are the long investment cycle times, the designer does not normally control the spending (the owner does), and the industry is inherently technologically conservative or risk adverse while accepting the often more significant geological, market and political risks.æSustainable Plant DesignÆ is an approach to plant and facility design that drives the necessary culture change and acceptance by minimising technical risk and maximising potential returns. The approach forces consideration of sustainability objectives and risks early in the project, where cost saving and efficiency improving opportunities can be maximised.In Hatch, we are using three proven tools under the ærisk managementÆ umbrella to drive sustainable development principles into our projects:Sustainable Plant Design, FutureWatchTM Reviews, and Clean Plant DesignTM . These proactive practical, not theoretical, techniques for driving change from within and reducing whole of life cycle costs will be discussed and illustrated with case studies.

Jan 1, 2004

By Goodheart B

The Australian Mineral Sands Industry has expanded from the initial export of mixed concentrates in the 1930s, through various development stages, to its current position as a leading world producer of individual mineral products and some further processed products. Opportunities for downstream processing of the separated minerals and locating such developments in Western Australia are reviewed, along with the role of the Western Australian Government in assisting resource development projects.

Jan 1, 1986

Ventilation challenges are often encountered when an underground mine expands to new zones and it often is the case to make a thorough review of the existing system and assess immediate and future airflow needs at the desired quantity and quality. An unexpected mine plan change that calls for increased development and production from new areas can impose a strain on the existing ventilation system. Budgetary constraints can also demand creativity in design on the mine ventilation engineerÆs part. Since the addition of several mining horizons it had become obvious at the Meikle mine that something had to be done to increase airflow quantity and quality in the old main zones because most of the ventilation resources had been channelled for development in the new mining horizons. An airflow assessment of the existing system had to be performed and it was determined that the airflow quantity had to be increased by at least 30 per cent and the quality of the air had to be improved by reducing nuisance and respirable dust and at the same time reducing the airflow temperature before it was used in a few mining zones. At the conclusion of the airflow assessment it was determined that a third centrifugal fan would be installed on a new 3.05 m diameter borehole from surface to underground. By a careful study of temperature conditions over time it was determined that an evaporative cooling spray chamber would be sufficient to cool the airflow down from the high dry bulb temperatures observed down to saturation at the wet bulb temperature. At the same time excessive nuisance dust generated as a result of the airflow travelling a long way in a haulage drift will be knocked down in the spray chamber resulting in cool, clean air in the mining districts. Expansion of the existing surface ammonia refrigeration plant was out of the question for several reasons. The fact that the airflow was hot and dry meant that evaporative cooling spray chambers could achieve lower working temperatures at a very low cost compared to the expansion of the chilled water plant. The expansion of the ventilation system at Meikle mine and the use of evaporative cooling spray chambers were demonstrated to be very successful and the information presented in this paper can be of benefit to other mines experiencing the same ventilation problems as was the case at the Meikle mine.

Jan 1, 2005

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008

By Barria J, Mencho J, Gonzalez GD

An extended Kalman Filter is used to build an on-line estimator of total ore, fine ore and water hold-ups in a SAG mill. In addition, an equivalent grinding rate from coarse to fine ore, as well as the discharge rates of solids (fines) and water are also estimated as part of the adaptation procedure of the model used for the Kalman Filter. The measurements used in the Kalman Filter estimator are the total mill weight provided by load cells, and inferred discharge flows of fines and water from flow and density measurements performed downstream. The net ore and water feed to the SAG mill are used as inputs to the estimator, and also the proportion of fine ore in the feed. As an example of how to introduce robustness in the estimation in the face of sensor bias errors, an estimation of the load cell bias error is introduced in the estimator, thus providing self calibration. The estimator presented in this paper has been tested by simulation using a detailed SAG mill mechanistic dynamic model comprising 27 size fractions well fitted to a pilot mill. The maximum error in the estimation of the operational variables - total and fine ore as well as the mill contents under different operating conditions - is about ten per cent.

Jan 1, 1993

By Sandenbergh RF

The debate on the mechanism of adsorption of gold and silver di-cyanide onto activated carbon could be divided into two schools of thought. On the one hand, it has been proposed that the combined effects of electrostatic and chemical interaction between the activated carbon surface and adsorbing gold di-cyanide anion results in the adsorption of the latter. On the other hand the `ion-pair' adsorption reaction mechanism has been vigorously advocated as the dominant mechanism responsible for the adsorption of gold di-cyanide onto activated carbon. It is maintained that gold is adsorbed onto the carbon surface as the neutral ion-pair [M"+][Au(CN)z ]". Adsorption is viewed as the result of mainly the chemical interaction while electrostatic interactions are neglected. The validity of the `ion-pair' adsorption mechanism may be challenged on a number of counts. However, the alternative mechanism (based on aqueous surface chemistry principles) has not gained general acceptance yet, because it has not been applied widely enough to explain the different adsorption phenomena associated with gold di-cyanide on activated carbon. In the present study the case in favour of an adsorption mechanism based on general aqueous surface chemistry principles is presented. A model framework is developed for the adsorption reaction mechanism of gold di-cyanide onto activated carbon which incorporates the effects of chemical and electrostatic interactions between the dissolved species, the aqueous solution and the carbon surface. This model is then employed to explain a wide variety of reported adsorption phenomena for gold di-cyanide on activated carbon, such as the effects of pH, the adsorption of different metal cyano complexes, ionic strength, and type and concentration of cations in solution. In addition the effects of cyanide and dissolved oxygen concentration were investigated. No ready explanation, in terms of aqueous surface chemistry principles, is yet available for the switch in adsorption behaviour that agrees with ion exchange to ion-pair adsorption with increasing ionic strength.

Jan 1, 1997

The subject of octanes and knock in petrol engines is of general interest, not only to the engineers and chemists in the petroleum and automotive industries, but also to the motorist who wishes to see some light through the haze of propaganda regarding "super" petrols. A mixture of petrol vapour and air will explode when a spark is passed through it if it contains more than one and a half per cent. or less than six per cent. of petrol vapour by volume. In a petrol engine the mixture has to be within the explosive range before it will operate. When the spark is passed it 'ignites the petrol vapour-air mixture which burns with rapid but finite progress of the flame front 'through the unburnt gases in much the same manner that a charge of dynamite is consumed. The turbulence of the gases in the cylinder under normal operating conditions more than doubles the velocity of the flame front and enables the combustion to be completed by the end of the working (expansion) stroke:KNOCKIf the cylinder head 'is poorly designed or is covered with a deposit of carbon, it is possible for "hot spots" to develop, and these can ignite the mixture before the spark is passed. This pre-ignition gives rise to an engine knock but is accompanied by a dull thud rather than the ringing knock associated with the true "knocking" found in a petrol engine and attributed to the detonation of the mixture. Until a few years ago it was thought that this detonation was due to a shock wave produced by the rapid combustion of the mixture, and sufficiently intense to cause ignition of...

Jan 1, 1951

By K H. Esbensen

The Theory of Sampling (TOS) has contributed significantly to chemometrics by allowing data analysts to become more aware of total measurement uncertainty as total sampling error + total analytical error. This has allowed a new view on, for example, validation of multivariate data models and their performance. This keynote focuses mostly on the reverse perspective: how can chemometric multivariate data modelling be of help in an augmented sampling context? The basic principles of multivariate data analysis are presented and application examples are outlined from several areas in the geosciences to facilitate answers to the question posed, including a geochemical multivariate anomaly concept defined by a multivariate background model. Applications from geochemical prospecting, geochemical mapping, environmental chemistry and anthropogenic outlier recognition are outlined, as are the interdependent relationships between geostatistical modelling (variographics) of singular variables versus linear combinations of a multitude of variables, in chemometrics called scores. The potential synergy between chemometrics and TOS is far from exhausted at this time; much work remains.CITATION:Esbensen, K H, 2014. Theory of sampling in a multivariate perspective – what can chemometrics contribute?, in Proceedings Sampling 2014 , pp 7–10 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Rintoul AH

Studies of many types and purposes are being carried out constantly by mining, minerals processing and other operating companies. Frequently, the staff requirements and special skills lie outside the resources of the operating companies, and needs arise for external consult- ing services. We examine the natures of a range of studies, the factors that influence whether they be carried out in-house or externally and then discuss the manner of execution. Aspects of both good and bad practice are highlighted in order to arrive at the basic principles that give the most benefit from study work. While the bulk of the discussion relates specifically to the execution of external studies of process plant projects, many of the observations can be applied equally to the execution of studies by one department of a large organisation for another, and also to studies of capital projects other than those involving process plant facilities.

Jan 1, 1975

By B Godel, E R. Ramanaidou, M Verrall

Fortescue Metals Group Ltd Iron Bridge (IB) operation is a magnetite deposit located in the Pilbara region of Western Australia situated around 145 km south of Port Hedland. This Mesoarchean deposit belongs to the 3230 Ma Pincunah banded-iron formations (BIF), a member of the Kangaroo Caves Formation, Sulfur Springs Group (van Kranendonk, 2000).

Sep 18, 2023

With the introduction of the Health and Safety in Employment (HSE) Act 1992 and the subsequent repeal of regulations pertaining to mining, there has been an upheaval of the management of health and safety in mines.  More than ever, employers know that they must ensure that their workers are competent to carry out their assigned tasks.

Jan 1, 1997

By Hamilton TM

The Holocene Minninup shoreline is a coastal barrier system stretching from Bunbury to Busselton, in southwestern Australia. It has developed in a microtidal swell wave environment, under the influence of the post- glacial marine transgression and Holocene sea level variation. Barrier sediments thin rapidly across a shallow shelf, and consist of quartzo-felds- pathic sands with a minor skeletal carbonate component. Holocene shelf deposits are laterally extensive sheets overlying Pleisto- cene limestone. Modern carbonate production is small. Development of the Minninup barrier system has been controlled largely by low rates of sediment input from terrigenous and carbonate sources, late Holocene sea level fluctuati,.,s, and pre-existent coastal landforms composed of Pleistocene limestone. Modern controls on sedimentation are the refracted, shoaling swell wave regime, and onshore winds, which combine to promote nett northward longshore drift. Holocene barrier systems of the southern Swan Coastal Plain are of several different types. These include prograded sequences of beach ridges overlying shoreface sediments, such as is found at Rockingham and parts of Geographe Bay, and complex polygenetic systems typified by the Leschenault Peninsula. Pre- liminary investigations of the barrier stratigraphy of the Minninup shoreline indicate that both progradational and polygenetic sequences are present. The processes involved in shoreline development and heavy mineral accumulation are being studied using aerial photograph inter- pretation, beach profile monitoring, sampling, and granulometric analysis. This will lead to an enhanced understanding of the mechanisms of heavy mineral accumulation, and assist in the development of genetic models as aids for Exploration.

Jan 1, 1986

By L Reynolds

The portable infrared mineral analyser (PIMA) was trialled to determine the extent and intensity of any hydrothermal alteration halo associated with gold mineralisation in the Hyde-Macraes Shear Zone (HMSZ) of the Otago Schist.   Twelve diamond drillholes through the HMSZ were analysed with the PIMA at a sample spacing of 1 m. The drillholes were selected on two traverses along the line of strike and down-dip of the mineralisation in and around Panel 2 of the Frasers underground development.   The study showed that the Hangingwall shear of the HMSZ has a more distinctive infrared signature in intersections with high grades. The Hangingwall shear in these drill holes is defined by a shift in the wavelength of the Al-OH absorption feature from ~2220 nm to <2210 nm. This shift is attributed to a change in the mineralogy from phengite to muscovite. Overprinting this trend in some of the drillholes is the presence of the 2210 nm Al-OH absorption feature, ascribed to kaolinite. Kaolinite also tends to be present in numerous other regions of the schist above the Hangingwall shear associated with steeply dipping faults and foliation parallel joints. In drill holes with low grades the Hangingwall shear does not exhibit any obvious infrared signature.   At the scale of study, the PIMA does not provide evidence for an alteration halo associated with hydrothermal mineralisation above the Hangingwall shear. Possible tectonic movement may have displaced any alteration halo that once existed, away from the zone of mineralisation. For this reason, PIMA apparently cannot be used for predicting the location of the Hangingwall shear during exploration drilling. However, the study did show that the PIMA could define the Hangingwall shear when the rocks were sufficiently altered and mineralised.

Jan 1, 2007

Since the initial discovery of phosphate rock resources in North West Queensland in 1966, significant changes in ownership and development direction have occurred. Initially development of the resource involved beneficiation to produce a more saleable grade of phosphate rock. However more recently development has focused on the production of a high analysis fertilizer product on the minesite. These changes have been influenced by economics, industry/government cooperation and a changing phosphate industry.

Jan 1, 1998

By T QUINLAN

A resource estimate uses data obtained by sampling an orebody. An example is described in which a random drilling pattern did not provide a representative set of assays, and the estimated resource was significantly less than the mine production. It is believed that a better estimate would have been made if the exploration holes had been drilled on a regular grid.

Jan 1, 1992