Search Documents

Around no subject of technical )uterest have prejudice and wrong-thinking in the past so wrapped a web of obscurity as that of the corrosion of metals.It is a matter which has primarily concerned the engineer, but the paucity of his training in chemistry and electrochemistry has been the stumbling block to a better understanding of its mechanism.Now that the more important conditions controlling corrosion have been scientifically.established, it can be seen that, with the exception of but a few of the minor points, the electrochemical laws enunciated by Faraday, Helmholtz; Nernst, and others, are sufficient to include all the facts of the process.The word corrosion (derived from the Latin rodere-to gnaw) is so often wrongly applied that a definition at this stage would be useful. As now understood, it means the dispersion and waste of the useful solid metal by conversion into a useless compound which mayor may not be retained on or near the metal remaining.Commonly the presence of these compounds is regarded as evidence of corrosion, but the converse is not necessarily true; the lack of visible corrosion products on a clean surface of metal is no criterion of the absence of this change. It may be difficult to prove that the erosion of such a surface has been caused by chemical and not by mechanical effects alone.

Jan 1, 1932

By Menne DM

The carbon-in-pulp (CIp)process has become well accepted and firmly established in the gold industry of South Africa and, at this stage, six large CIP plants are treating close to I million metric tons of material per month. Many small operators are also using CIP and additional large plants are either nearing completion, are on the drawing boards,. or are being considered. The programme of testwork that preceded the acceptance of the CIP process in South Africa was conducted over some eight years and has been previously described'-7. With the start-up of the President Brand CIP plant on 'calcine' in July 1980 and that of the Western Areas CIP plant on repulped filter residues in September 1980, the emphasis on the CIP process switched from pilot plants to these large plants - and has largely remained there. As it has started up, each new CIP plant benefited from the experience gained and the developments made, on earlier plants but, since so few plants have so far been established in South Africa, each new plant and each new design has revealed a further set of conditions to be met and problems to be overcome. However, in the highly collaborative atmosphere of the South African gold-mining industry, the results and observations from the operation of these first plants were shared by all mining groups. This paper will attempt to describe typical developments on, and results obtained from, these new large plants, and will incorporate significant results from the earlier laboratory and pilot-plant investigations.,

Jan 1, 1982

By Henderson J, Ward RG

Dissolved oxygen has been measured directly using a rugged, reliable, accurate electrochemical probe system developed for steelworks application by B.H.P. Central Research Laboratories. Furnace measurements show that the steel is generally supersaturated with oxygen and that oxygen contents vary considerably from heat. to heat. Ladle measurements also show considerable heat-to-heat variations. Analysis in terms of ladle deoxidation chemistry differentiates between carbon monoxide controlled and manganese silicate controlled oxygen levels. Deviations from these levels are sometimes due to aluminium present in other added ladle alloys but in some cases the plant applicability of laboratory derived equilibria is questionable.

Jan 1, 1972

By Butler RD

The Singhbhum Copper Belt is an arcuate zone of verthrusting which extends over a strike length of about 180 kilometres, located in Eastern India, 150-300 kilometres west of Calcutta. The Belt is noted for its mineralisation, and both copper and uranium are currently being mined within it.

Jan 1, 1990

The exercise of preparing this paper has been both enjoyable and thought provoking.In carrying out the research I have spoken and written to many people. Without exception they have been eager to help, all have spoken of the high regard in which they held Dr Williams, not only as a metallurgist but also as a person.Review of GK's life reveals an enormous impact on the industry in which he worked and the people with whom he associated. Consideration of this impact inevitably leads to the question "what can we learn from his life and the way he went about his work?"

Jan 1, 1985

This paper presents a summary of tools and methods used for geotechnical assessments and monitoring systems at block caving mines. A critical review of these tools is given based on the authorÆs experience in block caving operations. The reviewed tools include cavability prediction, fragmentation evaluation, geotechnical monitoring systems, numerical stress analysis and others. Some of these tools have been developed under certain circumstances in particular mines and experience shows that their applications under different geological and mining conditions have often been difficult. Examples from block cave mines are also utilised in this paper to illustrate the importance of the further development of these tools, whilst possible improvements on these tools are also suggested.

Jan 1, 2000

By J Walasiak

In the climate planning of mines and tunnelling with anticipated poor climatic conditions, and especially in case of longer working shifts, the main question is whether it can be reliably prevented that certain climatic limits laid down be exceeded. Working at high temperature and/or humidity can lead to reduced human working energy û a very important economic aspect û and to a risky lack of concentration on the part of the miners or to heat collapse and extremely dangerous heat stroke. With the Deutsche Montan Technologie GmbH (DMT) climate prediction programs, both the dry and the extremely significant humid heat transfer can be calculated. This is due to the high planning reliability involved. With the help of these climate prediction programs it is already possible to determine the anticipated climatic values for the operation phase as early as the planning stage of new ore or coal fields or of tunnel construction projects and to design the optimum air cooling system for every underground project with due regard to technical and economic aspects.

Jan 1, 2005

By Peres EC

The flotability of monazite, zircon and rutile in the presence of sodium oleate, potassium octyl hydroxamate and a commercial hydroxamate was investigated through microflotation tests in a modified Hallimond tube. Zeta potential determinations in the absence/presence of collectors were performed in a microelectrophoretical cell. The microflotation testwork showed that, in general, the flotability characteristics of all three minerals are very similar. Commercial hydroxamate is, by far, a stronger collector than the pure potassium octyl hydroxamate. Electrokinetic studies indicated that the adsorption of collectors shifts the isoelectric point (IEP) of the minerals towards lower pH values. These collectors also are capable of changing the zeta potential values to more negative figures in the pH region above the isoelectric point. An increase of the conditioning temperature, generally, enhances the floatability of the three minerals. A depressant is required in order that selective flotation is feasible in the system monazite-zircon-ruffle. Sodium metasilicate is an efficient depressant for zircon and rutile and affects only slightly the flotability of Monazite.

Jan 1, 1993

The current boom conditions in the Gold Mining Industry, open cut low grade gold mines have become the initial cash flow source for most companies. To achieve the required cash flow the head grade needs to be maintained at the required level. The methods of grade control to achieve .the planned head grade have evolved various systems, one of which is the Ditch Witch Trencher. The application of this machine has revolutionised open cut grade control and Geology and this paper records the various methodologies developed in the Eastern Goldfields of Western Australia.

Jan 1, 1987

By Luck D

Current methods of mucking out small development tunnels are a major limitation to improved efficiency and high rates of advance. This is particularly true in the deep metalliferous mines of South Africa, where the harsh environment, remoteness of operations and the hard abrasive rock conditions mitigate against the use of the tunnel borer type of equipment. The Loader Distributor Train was designed to overcome the special problems of hard rock tunnelling. It combines advanced innovative technology with proven simple methods of operation and maintenance. The system aims at taking advantage of new, efficient and cost effective power sources in South African mines based on replacing compressed air with electro hydraulics and the new concept of hydropower. It also introduces electronics and computer technology, for both automatic control and fault finding, into the production environment. The system is designed to permit sophisticated equipment to be operated and maintained by a semi skilled labour force. Although still undergoing trials it is believed that the Loader Distributor Train will prove highly effective, and that the new concepts offer considerable potential in areas other than flat tunnels, in particular the cleaning of inclined shafts.

Jan 1, 1986

During conventional eddy current separation, a repulsive force is applied to metallic particles by placing them in a rapidly changing magnetic field generated by a spinning magnetic rotor carrying an arrangement of alternate magnetic poles. This method works effectively for larger non-ferrous metallic objects, such as aluminium cans, but as the metallic particles become smaller, the bulk repulsive force on the particles is increasingly replaced by a rotational torque. Therefore, for small metallic particles it makes sense to use particle rotation, rather than particle repulsion, to effect a separation. Eddy current separators using particle rotation are similar in construction to present separators, but are designed to produce a rotating field of essentially constant angular velocity and field strength. Practical and economic particle rotation eddy current separations are possible down to particle sizes of about 200 ¦m, but separations, at probably uneconomic rates, can be carried out on particles as small as 50 ¦m.

Jan 1, 2000

Nuclear power stations to be installed in Australia will be fuelled from Australian resources of raw materials.This will require the establishment of new manufacturing industries and the eventual expansion of established activities, especially in uranium mining and the preparation of precision metal products.This paper presents some predictions of the possible growth of nuclear power installations in Australia.These might amount to 4000 MWE by 1985 and 11,500 MWE by 1990 and towards the end of the century, about 50 per cent of new generating plant might be nuclear.Predictions are given of the demands for materials (uranium and zirconium) and fuel manufacturing services for four reactor systems which might be considered in the programme.The availability of raw materials and technical capability place Australia in a particularly good position to undertake the manufacture of nuclear fuel; in addition to satisfying the domestic demand we should actively seek export markets for these products.

Jan 1, 1971

Various aspects of the history of mining at The Zinc Corporation, Limited (ZC) and New Broken Hill Consolidated Limited (NHHC) are examined. There are some discussions about the various methods used to mine the pillars left after the primary mining operations, with an enphasis being placed on the more modern pillar mining methods. Some new pillar mining proposals are presented. INTRODUCTION In the past, pillar reserves at ZC/NBHC have been scheduled for mining by labour intensive and high unit cost mining methods. These methods include both undercut and fill and overhand square set timber stoping. Recent technological advances in large diameter longhole drilling and high charge density explosives have culminated in the mechanised Vertical Crater Retreat (VCR) mining method and this method has been successfully used for the extraction of two pillars at NBHC and more stopes are planned. However the use of VCR methods for mining pillars at ZC/NBHC is restricted to approximately 50 per cent of the total pillar reserves and it appears that high cost methods will be needed to mine the remaining Pillars.

Jan 1, 1983

The Tailings Leach Plant at Chingola employs a Leach/Solvent Extraction/Electro- winning process and contains the largest solvent extraction plant in the world, with design liquor flow rates of 55 m3/min. A pilot plant constructed to provide design data also indi- cated areas of uncertain operating and control performance and led to a decision to model the whole circuit to determine the overall dynamic behaviour and basic operating characteristics. Details of the plant flowsheet are given and the basic physical and chemical' equations required for the simulation defined. Each unit operation is considered separately and details of the mathematical models used for their simulation presented.

Jan 1, 1977

Every step on the path from the mine to the smelter invites a comparison between material inputs on one side and outputs plus accumulation on the other. Or put simply, between what you think you have produced with what you find you have at hand. The discrepancy between these sets of comparisons is the error. Following that error in a systematic and objective manner is a way to improve the mineÆs measurement systems, that in turn leads to more accurate accounting for ores, metals and concentrates. Because the control of production is so tightly coupled with the accounting of materials, any lasting improvements in materials accounting will benefit the predictions of materials movements and quality. This translates to more reliable planning and scheduling in stockpile management, logistics, shipping and marketing. The statistical tools described are direct adaptations from the long-standing methods used to maintain the quality of manufactured product in the discrete parts industries. Their use in the process industries, of which mining is one, requires some care owing to the continuous nature of ore extraction and its variable properties. The tools can be used for problem diagnostics and as early warning systems. In common practice many professional staff, in attempting to get a perfect reconciliation between expected and observed results, try to explain away the error or bury it completely. The methodology advocated here requires a different mindset because the error must be given pre-eminence for lasting improvement to be realised.

Jan 1, 2002

By J Garritsen, P F. Wells, M Xu

IncoÆs Clarabelle mill currently processes ores from eight mines in the Sudbury basin area in Ontario, Canada. The ore from the Garson mine contains a much higher concentration of arsenic than the other ores. Adding this ore into the feed to the mill has resulted in an increase in arsenic content of the Cu-Ni bulk concentrate to a level that significantly affects the smelter operation, and more importantly the efficiency of Cu-Ni separation in the Matte separation plant. The arsenic occurs mainly as gersdorffite (NiAsS), with a small amount being in the form of cobaltite (CoAsS). Extensive laboratory tests on depressing arsenic in Garson ore flotation have been conducted and two reagent suites have been identified as effective arsenic depressants. One is the so called MAA depressant which is a mixture of magnesium chloride, ammonium chloride, and ammonium hydroxide. This reagent combination was reported to depress other arsenide minerals such as arsenopyrite (FeAsS) and enargite (Cu3AsS4). However, in this study for the first time it has been shown to have a depressing effect on gersdorffite. The other reagent suite, a mixture of triethylenetetramine (TETA) and sodium sulfite, that has been reported as an effective pyrrhotite (Fe1-xS) depressant in pentlandite ((NiFe)9S8) flotation, has not been reported as gersdorffite depressant before. The effectiveness of both reagent suites is more pronounced when the arsenic minerals are oxidised through pulp aeration or the addition of hydrogen peroxide. With a flow sheet consisting of a magnetic separation, rougher- scavenger flotation, followed by regrinding and cleaning of combined magnetic and scavenger concentrate, the arsenic recovery to the final Cu-Ni bulk concentrate was reduced from 73 per cent in baseline test to less than 30 per cent with either reagent suite at no decrease in nickel recovery. The TETA/sulfite reagent combination has the advantage over the MAA suite in that pyrrhotite is also depressed, rather than being activated, and the copper and nickel concentrate grades are therefore increased.

Jan 1, 2005

Anyone who has driven backwards using only their rear view mirrors knows how difficult it is to avoid spinning the steering wheel the wrong way. So why run your mine that way? Traditionally Reconciliation has focused on the past performance of the mine. In this paper we make a case for Prognostication û the act of forecasting or predicting something in the future from present indications or signs. Reconciliation is a common activity carried out at most mines around the world. Countless geologists and engineers spend hours poised in front of spreadsheets diligently comparing how their resource/reserve model, grade control, and survey pick ups compare to what was actually produced. The result is usually a group of factors, which are applied to future estimates in an attempt to better predict how the operation may perform. Unfortunately, if the road ahead isnÆt the same as what you have just been down, youÆll be æoff-roadingÆ in no time! An alternative is to constantly collect and analyse key measurements that are used to calibrate critical estimates in an iterative process. When variations occur, they are analysed and corrective action is taken to ensure the estimates and measurements realign. In this way the estimates become forecasts and can then form the basis for decision making to ensure that what does happen in the future will match the plan or schedule. By automating this process, some mines have been able to be proactive on a daily basis in order to improve the overall performance of the operation. This paper outlines the key estimates and measurements used for reconciliation, details the characteristics of an automated web based information management system to facilitate the process and provides some insights about how mining operations might move beyond reconciliation.

Jan 1, 2003

The five main ways in which coal is used are1. for electricity generation,2. as a lump fuel for domestic and industrial purposes,3. for gas making,4. for making carbon for chemical and metallurgicalindustry, and5. as a source of coal tar and coal-tar chemicals.In the past about 80 per cent of Victoria's brown coal has been used for power generation and the rest for making a lump fuel, in the form of briquettes. Some of these briquettes have been used for gas making, and a carbon industry based on them has recently been commenced, and could expand rapidly. However the enormous increases expected in power requirements, approximately a doubling every 10 years, will ensure that even if the manufacture of carbon increases dramatically and a large amount of coal is used for other purposes, the brown coal industry will always be dominated by power generation. As new fuels such as natural gas, oil, and nuclear fuel become available at competitive prices these will take their share of the power generation load.Natural gas or oil, or possibly pumped storage hydro, will almost certainly be used for all future peak-load stations, comprising around 40 per cent of the total installed generating capacity, but new base load stations will continue to be designed for brown coal operation until about the mid-1980s, by which time nuclear power stations will become competitive. By this time Victoria will have installed about 6000 MW capacity of brown coal stations, burning around 50 million tons/year of coal, compared with 18 million tons/year at present, with perhaps 15 million tons/year being used for other purposes.This consumption of 65 million tons/year should then remain fairly stable over the life of the power stations installed, well into the 21st century. Brown coal therefore appears to have an assured place in providinga major part of Victoria's fuel requirements, despite the diversification in fuel usage pattern which appears certain to occur with the recent developments in new fuel resources.

Jan 1, 1971

By K Li, C Zhang, i, J Oh, S Saydam, H L. Ram

Rock surface roughness plays an important role in excavation engineering projects and applications related to surface support structures, such as shotcrete and thin-sprayed liner (TSL). The morphology of the substrate affects the mechanical behaviour at the interface significantly. Therefore, it is necessary to quantify the roughness to investigate the relationship between roughness and mechanical properties. The joint roughness coefficient (JRC) proposed by Barton and Choubey (1977) is widely used in practice. It initially estimated the roughness by comparing it to 10 standard profiles visually. However, this method has lots of limitations, it is not only subjective but also a two-dimensional parameter with a small lab scale (Beer, 2002). The subsequent research on JRC, from visual comparison with Barton’s standard profiles to measuring the roughness with a profilometer (Weissbach, 1978; Alameda-Hernández et al, 2014). Then, 2D profiles or 3D surfaces by different technologies with higher resolution and accuracy, such as 3D laser or optical scanners (Fardin, 2004; Jiang, 2020, 2021). These 3D scanners are expensive and only suitable for laboratory scales. LiDAR scanners (Lato, 2009; Aubertin, 2022) have been applied in industrial size, but it is difficult to achieve a millimetre-level accuracy, which is mostly used to detect the thickness of shotcrete in practice. Thus, finding a cost-effective surface roughness measurement method with high accuracy is necessary. Photogrammetry is another method to digitalise the roughness of the surface. Similar to 3D scanners, photogrammetry also generates the point cloud of the objective surface and then reconstructs the 3D model of the objects. 3D reconstruction technology is a trendy technology in recent years. The structure from motion (SfM) algorithm (Westoby, 2012) to rebuild the 3D model with a flexible workflow, aligning photos, building dense point cloud, mesh and texture, which has been proved that can rebuild an accurate model in variable fields.

Nov 29, 2022

By Braes J. R, Neale J. R

The New Broken Hill Consolidated Limited (NBHC) mine currently produces 1.42 million tonnes of silver, lead and zinc ore annually. All of this ore is treated by the NBHC milling ccx[plex. This paper describes the crushing, grinding, flotation and filtration circuits used in the treatment of this ore and lists the major items of equignent used in these circuits. Metallurgical results, manning levels and consumption rates of reagents and grinding media are shown.

Jan 1, 1983