Search Documents

By G Billing a, D Gribble, E Hall, D Varga

The theoretical benefits of electronic detonators have been reasonably well documented. To support this, a practical comparison was made between the performance of the standard shock tube system, NONEL, and a high precision electronic system, HotShotÖ, at the Sunrise Dam Gold Mine. The expected benefits from electronic detonators to Sunrise Dam were identified prior to the trial. Based on these, a number of objectives were set to demonstrate the value of the HotShot system. These are an improvement in fragmentation leading to an increase in productivity, less oversize rehandling, increased throughput and more uniformity in muck pile movement. To maintain the integrity of the trial, the nominal timing of the shots was kept exactly the same, thereby restricting any performance improvements to the precision of the electronics. Accordingly, adjacent shots were chosen with consistent geology. Video footage was taken of the blasts and vibration monitoring was carried out by fixed geophones throughout the mine. Spot heights of the muck pile swell were taken immediately after the blast and heave profile graphs were generated for comparison. Video footage was taken for a period of three hours for both shots to analyse cycle times of the excavator and trucks. PITRAM data was also collected for analysis. As far as practicable, the ore was taken to the same finger on the run-of-mine (ROM) pad to assist in single sourcing for the crusher and to allow oversize to be separated out. From specific metrics taken during the trials, it was shown that the expected improvements due to the high precision timing of electronics were realised in all areas.

Jan 1, 2007

In November, 1967, a four strand curved mould continuous casting machine coupled with a 50 ton basic oxygen furnace began producing billets for the rod mill and new merchant mill at the Newcastle Steelworks. To date over 500,000 tons of carbon and alloy steels have been cast at the rate of 20,000 tons per month, the major part for the wire industry. Many alterations have been made to the plant to simplify the process, improve quality and increase production. Casting parameters have been developed for each different type of steel. The quality of the final product has been influenced most by casting temperature, secondary cooling and casting speed. All these factors have been controlled and good results are reproduced. More exacting requirements of liquid steel quality have brought about the use of higher lime/silica ratio slags during steelmaking to control phosphorus revers- ions and standard ladle additions of manganese suicide and ferro aluminium for more effective deoxidation.

Jan 1, 1972

By Bhattacharyya AK

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research Workers.

Jan 1, 1992

By Brouwer G, Shaw J

As South African gold mines go deeper, and improved and more uniform working condi- tions are required, ever larger amounts of refrigeration are needed. At the same time new and more suitable cooling equipment is becoming available for use with new mining layouts as well as on existing shaft systems. The advent of the large diameter rotor screw compressor has meant that there is now a machine available with great flexibility in performance and construction for efficient underground use. The first installation using this type of machine is described.

Jan 1, 1988

By Paine G. G

The Red Dome Gold/Copper Mine is located approximately 15 km west of the township of Chillagoe which itself is approximately 220 km by road west of Cairns, Far North Queensland. The deposit, with other mines in the Mungana region, was worked from about 1901 to 1927. Exploration by Amoco Minerals Australia in the 1970s and early 1980s outlined a geological resource of 15 million tonnes. A mining reserve of 9.3 million tonnes was identified and originally developed by Elders Resources Limited. The mine commenced operations in March 1986 and was the first large-scale gold project in Australia to be developed solely on the heap leach process. The mine operated successfully as a gold heap leach operation until 1989 when new grinding, flotation and carbon-in-leach plant facilities were installed to process the non heap-leachable component of the orebody including the copper rich -ore. In March 1991, Red Dome Pty Ltd became a wholly owned subsidiary of Niugini Mining Limited. After six years of successful operation and having excavated a 200 in deep pit, it became evident in 1992 that unless more open cut reserves could be identified the operation was limited to six to nine months of high grade ore and a further 15 months of low grade stockpile material. A preliminary feasibility study was carried out to assess the viability of deepening the open cut. This indicated that from a technical and financial point of view it was possible to expand and deepen the open cut. This presented the daunting challenge of developing a 300 in deep, single access, open cut between a high chert ridge, a government railway line and a National Park. The meeting of this challenge is the subject of this paper.

Jan 1, 1994

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

By Rogis J

The basic parameters causing outbursts are rock pressure, gas characteristics and the physico-mechanical properties of the coal. The three sets of factors are to some degree interdependent. At Collinsville, the gas characteristics coupled with the physico-mechanical properties of the coal appear to be the major factors contributing to outbursts. The relative importance of rock pressure is uncertain. The following geological parameters appear to be necessary before outbursts can occur. 1. A coal rank greater than 1.2% vitrinite reflectance. 2. Thrust faults with throws greater than 3.Om or strike- slip faults with coal gouge wider than 0.3m. 3. Seam gas emission values greater than 1.1 cm3 /g. Igneous intrusions are the likely source of the carbon dioxide seam gas. Outbursts have occurred at depths ranging from 215m to 265m. They occur at these relatively shallow depths due to: 1. the high rank of coal at the present topographic surface and the high coalification gradient; 2. the relatively high degree of tectonic deformation of the strata; 3. the seam gas characteristics; and 4. the extent of igneous intrusions.

Jan 1, 1980

Models of the genesis of existing ore oodles and targetting of exploration for new mines are greatly enhanced by an-understanding of the plate tectonic environment existing at the time of mineral emplacement. In areas of recent or active tectonism, a study of the present-day crustal and upper mantle structure is an obvious starting point in unravelling the evolution of the accessible upper crust. Bougainville is the northern-most island in the Solomon Islands arc. A 7km deep trench almost 100km off its western coast marks the commencement of subduction of the Solomon Sea plate beneath the Pacific plate. As outlined by the seismicity, the subducted crustal slab under the southern half of Bougainville reaches the axis of the island at about 100km depth, from which point it dips near vertically another 300km into the upper mantle. Large surface blasts at the Bougainville Copper Mine at Panguna, Bougainville, Papua New Guinea were used to derive an unreversed upper crustal profile of the island. The crust appears to be relatively simple, being comprised of a 5km deep layer with a P-wave velocity of 4.5km/sec, overlying a l0km thick layer with a P-wave velocity of 7.2km/sec. Constraints on the 15km mantle depth were provided by the identification of both P to and S to P phase conversions of seismic waves from local shallow earthquakes at the Moho boundary. An upper mantle velocity of 7.95(¦ 0.15) km/sec was measured from travel times of selected shallow earthquakes along the strike of the island arc.

Jan 1, 1987

By Nguyen V. V

The development of structural defects in the overburden material immediately behind a production blast was studied using surface and subsurface techniques. A significant increase in vertical and horizontal fracture intensity was recorded. The extent of fracturing into the highwall appeared to be dependent on the structural and petrologic characteristics of the various lithological units and the relative position of the explosive charges. A shallow zone of disruption to a depth of 10 m and extending to around 30 m from the newly formed highwall crest was recorded. Horizontal fractures in lower units of the overburden sequence were recorded at distances up to 50 m from the new highwall Face.

Jan 1, 1981

By E P. Donohue

Changes to water industry practice are required as a consequence of the Council of Australian Governments water reform agenda which binds all states and territories to a range of measures intended to drive new efficiency, sustainability, higher value use and proper provision for environmental needs. Queensland is implementing its reforms program through its water resource planning process, a legislatively underpinned program that provides for a new level of social, economic and environmental security. A water resource plan for the Fitzroy Basin has been finalised and its implementation plan, which details infrastructure operational arrangements for the basin, is due to be released later this year. The mining industry is a major contributor to the economy of the Basin, and although a comparatively minor water consumer, is now aligning its water use practices with the stateÆs maturing integrated resource management paradigm. This new culture presents both challenges and opportunities. Water reform in the Fitzroy basin is well advanced. The processes and institutional arrangements that have been developed are of significant importance to the aspirations of current and future minerals development. This paper outlines the current status of those reforms and the likely institutional framework for the near future. The paper also discusses how the reforms impact on the availability, access and security of water available to mining interests.

Jan 1, 2003

The explosion of a charge in a drillhole sets the surrounding rock mass into vibrating stress wave motion. Except in the immediate vicinity of the drillhole, the dynamic stresses associated with this motion do damage only to pre-existing joints, cracks, or other weak planes, not to the rock material in between these. The joints are weak in tension, therefore the damage occurs as a result of tensile stresses. The initial damage process in the rock mass that ultimately breaks loose in front of the hole is similar to that in the remaining rock behind the drillhole. Recorded or calculated values of the vibration velocity and frequency contain a wealth of information about the combination of stress and strain that causes the damage. This paper outlines a new technique by which the peak strain energy derived from measured or calculated vibration velocity records is used to determine the local fragment size distribution. It combines two previously known and well tested techniques, namely the Holmberg-Persson calculation of the peak vibration velocity generated by an extended charge and King's calculations of the fragment size distribution as a function of the strain energy in rock crushing. Both of these calculations are based on experimental data and have been tested and found to agree well with actual conditions in their respective fields. Holmberg-Persson's calculated peak vibration velocities have been used successfully to predict and control damage to the remaining rock in cautious blasting, while King's calculation successfully describes the comminution of rock in mechanical crushing. Preliminary predictions of fragmentation in two types of rock blasting, a large hole open pit mining blast and a tunnel round, indicate that the new technique for fragmentation prediction has the potential for predicting fragment size distributions within the rock removed by the Blast.

Jan 1, 1995

By Reifenstein A

ACIRL's petrographers apply microscopic techniques to coal exploration, production, preparation and processing problems and research investigations as well as provide a commercial service for quality control of export coal shipments. This paper describes a number of case studies of applications of petrography to coal industry problems and coal research, including

Jan 1, 1989

By J Czerwinski, M Kasper, M Wyser, N Heeb

The VERT project 1993 - 1998 laid the technical foundation for curtailing the emission of fine particles from diesel engines at Swiss underground workplaces. The targeted maximum was 100 ¦g/m3 EC. Extensive laboratory and field investigations demonstrated that this specification is only attainable with modern diesel particulate filter (DPF) systems that almost eliminate particles in the entire lung penetrating size range from 20 nm to 2.5 ¦m. In January 2000, Switzerland mandated compulsory particle filters in underground workplaces, particularly in tunnelling, irrespective of engine age, size and type. After the implementation, the particle concentration in the respiratory air was below 40 ¦g/m3 EC, compared to earlier values of up to 750 ¦g/m3 EC. Deployed DPFs have proven filtration rates of 99 per cent in the entire size range of alveoli intruding particles. The DPFs are as durable as the engine, suffer no ageing and require minimal maintenance. The failure rate is below three per cent annually. Of the 6000 retrofitted construction machines in Switzerland, about 400 are deployed underground. Prerequisites for this quality are a sophisticated certification procedure, electronic monitoring of DPF operation and meticulous periodic exhaust gas inspection of the engines.

Jan 1, 2005

By Viney K. G, Molinia A. B

The Hellyer Pb-Zn-Ag orebody in western Tasmania was discovered in 1983, and mine production at a rate of 250 000 tonnes/yr commenced in 1987. Expansion to 1 million/yr will be completed by early 1989. Exploratory development to gain access to the orebody, to provide a 20 000 tonne bulk sample for pilot plant work and to confirm mining conditions and orebody continuity was undertaken using conventional drill and blast techniques and large diesel trackless equipment. A ventilation shaft was raisebored. Development in this phase totalled 2 815 m and provided a sound basis for rapid expansion of the mine.

Jan 1, 1988

Through the stress synthesis of many examples of macrostructure in the middle of China, it can be concluded that in the middle of Chinesetectonics there are two compression-torsion-forces, one of which ( from NW to SE ) came from the northwest side of Aerjinshan abyssal and giant fault("F1A", see Fig.7,8,9 ); the other (from S to N ) came from the south side of the north piedmontal fault of Kunlunshan-the south piedmontal fault of Qinlingshan ("F2K-F2Q", see Fig-7,829 ).Owing to the two compression torsion forces a new special type of structure named rotation-apart structure occurred from Chaidamu basin to Hebai, Henan, Anhui plain,from Caledonian movement, Hercynian movement,Yenshan movement to Himalayan movement, step by step In the north of Qilianshan during the late Caledonian movement: during the Hercynian movement it extended into a vast area including the Chaidamu basin and Eerduosi basin; during the Yenshan movement it spread over the whole area of Helanshan,Eerduosi basin and Hebai , Henan, Anhui plain. In the period of Himalayan movement all these structures revived .The rotation-apart structure controlled the distribution of all mineral deposits and also were the mineralizing structures.The relation between these rotation-apart structure and earthquakes is very close.

Jan 1, 1990

Upper Cretaceous and Eocene coal measures of the Ohai Coalfield are stratigraphically complex, and coal seam geometry and quality are influenced by washouts and partings resulting from accumulation in a fluvially active environment. Mining efficiency is influenced by these seam discontinuities, which are difficult to predict in the absence of refined paleoenvironmental models of peat accumulation. Petrographic variations between the Upper Cretaceous and Eocene coals indicate differences in the environments of peat accumulation. Seams in the Upper Cretaceous Morley Coal Measures accumulated autochthonously (in situ) in predominantly forest swamps with a high water table. These swamps were occasionally subject to brief floods. No significant changes in swamp vegetation, as indicated by petrography, have been detected between seams. In contrast, the greater content of mineral matter and maceral detritus within the Eocene Beaumont Coal Measure seams indicates hypautochthonous (locally transported) peat accumulation under more frequently flooded conditions. A precursor forest-moor is again indicated but the greater resin content of these coals compared with the Upper Cretaceous examples may suggest a greater contribution from conifers. Integration of coal petrography with investigation of other seam characteristics and coal measure sedimentology is expected to result in a detailed understanding of original depositional controls on peat accumulation. Paleoenvironmental models derived in this way should facilitate prediction of seam geometry, roof and floor conditions, and variations in coal quality, with obvious benefits to exploration and mine development.

Jan 1, 1983

FaulIing west of the Mount Isa mine is described and is shown to be related to three groups of folds that have been recognized in the area. The first period of faulting postdates the first generation folding; these faulIs are regional faults (tectonic discontinuities) which are folded by second generation folds. The faulting accompanying the second generation folding divides the area west of the Mount Isa mine into four structurally and metamorphically identifiable blocks. The most prominent of these second generation faults is the Mount Isa Fault, which is characterized by a number of distinct zones of intense second generation folding and the presence of localized layers of mylonite. Only limited evidence for brittle deformation has been observed and the major movement appears to be associated with the plastic deformation of the rocks. Confined to the areas of second generation folding in the Mount Isa Fault are numerous third generation kink folds. A detailed description of the Mount Isa and other faulIs is presented together with evidence for their existence. The displacement accompanying this faulting cannot be established because of the complexity of the structure.Postdating these faults and all the folding of the area are minor cross faults.

Jan 1, 1973

Syferfontein Colliery, part of the Sasol group of companies which specialises in the field of petro-chemical production, was established in 1990. The mine is situated about 150 km east of Johannesburg, South Africa. Two coal seams are mined, utilising two 75 m3 draglines, shovels and a fleet of 177 ton rear dump trucks. The mine will reach its full production capacity of seven million tonnes per annum in 1992. During the planning period, prior to the establishment of the mine, management were confronted with the unstable socio-political environment in South Africa which could jeopardise the eventual success of the mine. They consequently conducted a strategic planning exercise to determine guidelines for mine planning to improve the chances of success in this unstable third world environment.The strategic guidelines formed the basis for specific actions taken during the planning and commissioning of the mine. Specific actions were taken in the field of operating cost, labour relations, working environment, logistics and the general environment. First results indicate that these actions have played a major role in the success of the mine to-date. This process can be utilised by others facing similar or even totally different uncertainties.

Jan 1, 1992

The Australian Mineral Industries Research Association, set up by the mineral industry in 1959, acts as a research and development broker and manager for the industry. In 1984/85 it contracted out just over $3 million of projects. Its structure and method of operation is described and highlights of some of the successful projects are given. The complex process of developing new proposals is described. This involves the establishment of effective communication networks within the industry and between the industry and research personnel working outside it. The advantages of the industry tackling some of its problems on a jointly sponsored basis are listed. Possible avenues for future development by the Association are given.

Jan 1, 1986

By G J. Corbett

Magmatic-related low sulfidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.   Low sulphidation systems in the south-west Pacific region exhibit a vertical zonation in deposit types: from porphyry copper-gold at deep levels, quartz-sulfide-gold at mesothermal to deep epithermal levels, carbonate-base metal gold at mainly epithermal levels, and epithermal quartz silver-gold at shallow levels. It is interpreted that the characteristics of each of these styles of deposits is produced by mixing with circulating waters of different physio-chemical compositions.

Jan 1, 1995