Search Documents

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

The prevention of silicosis by metallic aluminium has been reported by Denny, Robson, and Irwin in two papers. The first was published in 1937; the second, in 1939. The results definitely established that silicosis was prevented in animals by the inhalation of small quantities of aluminium. The present communication records subsequent progress in this field of research.

Jan 1, 1944

By H Catchpole, L FontbotT, J PTrez, M Ageneau, A Bendez·

In the world-class mining district of Morococha, epithermal polymetallic replacement bodies and veins overprint porphyry mineralisation and skarns related to subvolcanic intrusions of Miocene age, thus indicating ore formation in two different environments, separated in time or forming a continuum. The district covers an area of about 70 km2 in the north-western part of the Domo de Yauli complex in theWestern Cordillera of central Peru and is part of the Miocene polymetallic belt, also hosting the deposits of Colquijirca (Bendez· et al, 2008b) and Cerro de Pasco (Baumgartner, FontbotT and Vennemann, 2008). Multiple late-Miocene porphyry stocks intruded Permian, Triassic-Jurassic and late-Cretaceous sedimentary carbonate and volcano-sedimentary formations, as well as large mid-Miocene barren intrusions. Extensive field work and detailedmapping of different styles of orebodies suggest that ore formation in the area was related to the late-Miocene magmatism. Good outcrop conditions and superimposing of different mineralisation styles make Morococha an ideal location for studying ore-forming processes in a complex porphyry-related magmatic-hydrothermal system in which porphyry-to-epithermal transition occurred. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

Leichhardt Colliery is developed for underground mining of coal seams at depths exceeding 280 m. Investigations of the area were conducted in phases, each designed to delineate seam characteristics more accurately and to indicate with increasing precision the nature of local geological features and the ranges of those coal properties susceptible to variation. The investigational campaign is described phase by phase summarizing evaluation of the area at the conclusion of each phase. Predictions of geological conditions likely to influence engineering planning are contrasted with actual conditions observed during trial mining.

Jan 1, 1974

By C Tukel

Copper sulfate is traditionally used to activate various types of sulfide minerals. The list of users includes Falconbridge Sudbury operations, where copper sulfate solution is added to the pyrrhotite/pentlandite middlings at the scavenging stage. Results from some batch tests reported in the literature suggested that copper activation is helpful for the improvement of pentlandite recovery, especially in the difficult to float fine particle range. Any improvement in pentlandite recovery is important since it is the main nickel bearing sulfide mineral. The impact of copper sulfate for this function has been investigated. Since the focus of current investigation was the flotation behaviour of minerals at the scavenger stage, rougher flotation was kept as constant as possible at two different weight recoveries, namely 13.2 per cent and 15.5 per cent that is relevant to industrial practice. Samples taken during batch testing were extracted using DETA and flotation products from selected tests were analysed to determine the recovery by size behaviour in relation to the use of copper sulfate. Results provide significant evidence that the addition of copper sulfate to these middlings does not yield greater nickel recovery, either on an overall or specific particle size basis. It is concluded that copper sulfate is wasted in the process and that self activation behaviour of the ore at a slightly reduced pH is sufficiently significant to maintain the scavenger recovery of pyrrhotite and pentlandite at desirable levels. Results obtained from limited circuit trials have shown supporting evidence for this conclusion.

Jan 1, 2005

By Bevan JE

The US Bureau of Mines is conducting research to improve the health and safety for underground coal miners, and the efficiency of the mining systems that are used. In 1986, the Bureau began a major research effort on the technology for computer-assisted mining systems for underground coal mines. The initial target was technology for continuous mining machines that would allow them to extract coal by computer-assisted operation. Technology areas being investigated include guidance systems, machine condition systems, computer systems, machine control, human-machine interfaces and planning. In each of these areas, individual system development has progressed to where underground testing of these systems will begin in 1991.In addition to coal extraction, the Bureau has also begun research for the development of technology for computer-assisted roof bolting. The Bureau is developing technology for a "smart" roof bolter that would be able to sense and analyze strata conditions to determine the requirements to provide a competent roof. The system would determine the location of the hole, drill the hole to length, and select and install the appropriate bolt.

Jan 1, 1991

Metsim is proving to be a powerful tool when designing a heap leach operation. The most useful outputs arc determining the fluctuations in pregnant solution recovery rate, make-up water rate, gold recovery rate. and pond levels. Detailed data are needed for input: a pad loading schedule, a mining rate schedule for each ore type, column leach test data for each ore type, column tests on water dynamics (ie hourly flow-out versus-in during saturation and drain-down), monthly rainfall and evaporation data, and proposed pond dimensions. These data allow 'what if' studies on application rates, leach rates, loading rates and other variables of interest. Examples will he given of modelling both a rectangular pad and a valley fill operation.

Jan 1, 1994

Nickel WestÆs Kalgoorlie Nickel Smelter operates three Peirce-Smith converters, each processing 110 tonnes of matte per charge. The vessels are lined with chrome-magnesia refractory with a mouth traditionally constructed from steel liner plates, protected with cast refractory. Mouth refractory is damaged by molten material and the action of cleaning solid buildup off the mouth. Once damage has accumulated, the mouth must be frequently maintained with hot refractory gunning or a mouth leak may occur. Such a leak requires a 32 hour repair period. A converter mouth redesign program was undertaken with the aim of reducing the rate of mouth damage during operation, eliminating mouth leaks and shortening mouth replacement times during vessel rebuild periods. An overview of the redesign process and operational performance is contained herein.

Jan 1, 2005

By Bingwen Z, Fengyi K

The hydraulic-stowing mining method is most effective for mining thick coal seams. It is superior to the sliced cover- caving and artificial mining method and the fully mechanized sublevel-caving mining method for the following reasons - a much higher recovery rate is achieved, there is much less surface subsidence and roof pressure, there is no hidden danger of gob fire, and much less methane emission and coal dust problems, etc.. However, its superiority is overshadowed by its backward stowing technique which makes mechanisation of mining and stowing difficult, causes bleed water interference to production and to the environment and is uneconomic because of the high cost of stowing material. These disadvantages limited its application to coal seams that are difficult and not suitable to be mined by other mining methods. The remedy is in reforming it thoroughly to permit mining of otherwise unminable seams and this paper presents the reformation.

Jan 1, 1992

By Muir D. M

Highly saline process water has a number of implications for the CIP process during the leaching, adsorption and recovery of gold. The reduced oxygen solubility in saline water can seriously reduce the rate of gold leaching, while dissolved oxygen meters do not necessarily reveal actual oxygen concentrations in saline water. High levels of magnesium in the ground water necessitate operation at lower pH (-9), with the potential for greater cyanide loss via HCN stripping. In addition increasing salinity renders viscosity modifiers largely ineffective.The adsorption capacity of aurocyanide onto activated carbon is improved with increasing salinity, but misleading results can be obtained in assessment of gold loading kinetics of plant carbon samples already loaded, or partially loaded, in saline water if subsequently tested in fresh water. Elevated chloride levels in the Zadra elution process can cause severe anode corrosion in the elecuowinning cell. The Anglo elution process is tolerant to only slight increases in water salinity, but elution times can be reduced by ethanol addition. Care is required in carbon regeneration, as salts can catalyse carbon decomposition as well as increase kiln corrosion.

Jan 1, 1994

By Quemard D, Troncoso J

The Gordonstone Project with a capital cost in excess of $500 million will become the largest underground coal mine in Australia. The project development decision was taken on 31 July, 1990 and at 31 May, 1991 construction was approximately 35 per cent complete. The first train of processed product coal will be railed to Gladstone during December 1992. The general theme of this paper therefore will address the planning and development processes at Gordonstone particularly the interrelatedness of technical, production, construction and environmental disciplines to ensure success during operations.

Jan 1, 1991

CONTENTSSummaryIntroductionGeographical and Geological Outline of the RegionGrowth of the Mining IndustryTable 1: Production StatisticsGeneral GeologyRecent Alluvium and River GravelsSambeto SeriesMudstone and Basalt ContactVatukoula SeriesIntrusivesStructureGeologic HistoryLodesTable 2: Principal Lodes and Their OrebodiesMineral Assemblage and ParagenesisOre Shoots and Their ControlEmperor MineLoloma MineDolphin MineExplorationConclusionAcknowledgmentReferencesSUMMARYThe Tavua Goldfield was found in 1932 within a basin, both topographical and structural, near the sea on the north side of Viti Levu, Fiji, and has produced over £13,000,000 (Fijian) worth of gold and silver from the three mines...

Jan 1, 1953

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

By K S. E, S C. Parker, T K. Kundu

Understanding the fundamental principles governing the reactions at surfaces has always been the goal of theoretical surface science. The atomistic simulation techniques have been used to calculate the surface structures and the stability of quartz and wollastonite, and their adsorption behaviour in the presence of molecular and dissociative water, and the two widely used collector head group molecules of methanoic acid and methylamine. The dissolution behaviour of wollastonite has also been modelled. The calculated surface energy, hydration energy and reaction energy values have been examined and discussed in the light of flotation literature. These studies have given an insight into the interactions at atomic level, which indicate that modelling techniques should be capable of predicting the adsorption behaviour and to design the selective collector molecules, which is of central importance to the mineral processing technique of flotation.

Jan 1, 2005

Stability on surface mining projects is primarily controlled by five factors. These include structural geology, the most important of the factors, the existence of weak layers, primarily clayey gouge or clay infill, groundwater, blasting and weathering. Case examples of stability on many surface mines including some coal mines are presented. The experience and lessons learned are applicable in some way to stability of surface coal Mines.

Jan 1, 1986

By Bayly MG, Harris JA

The current operational practice at the Territory Enterprises Pty, Limited uranium oxide plant,, and some aspects of researc$ and development work at Rum Jungle are outlined with pertinent comments on some overseas practices.

Jan 1, 1968

The evolution of the Oaky Creek mining complex provides a good example of the mining cycle in practice. Oaky Creek has been innovative in its choice of mining methods, with virtually the full range of coal mining methods having been used as workings have progressed down dip. The history of the mine is traced through its development (and ownership changes), progressive selection of mining methods as depths of cover to seams being mined have increased, and rehabilitation. This allows the different mining methods to be described and illustrates the concept of æwall-to-wall miningÆ.

Jan 1, 1998

By J D. Bryant

The Ernest Henry Copper-Gold mine, the third largest copper deposit in Australia, is located 35 km NE of Cloncurry in the Mt Isa-Cloncurry mineral district of NW Queensland. Ernest Henry Mining Pty Ltd (EHM), a wholly owned subsidiary of Xstrata Copper Australia, operates the mine. Approximately 10.2 Mt of ore grading 1.12 per cent Cu and 0.56 g/t Au were processed during the 2001 - 2002 financial year. The Ernest Henry plant produces copper-gold concentrate, which is trucked to Mt Isa for smelting. The Ernest Henry deposit is a member of the diverse Fe-oxide-(Cu-Au) class of deposits. The orebody is hosted within a sequence of moderately SSE-dipping, intensely altered Paleoproterozoic intermediate metavolcanic and metasedimentary rocks. Copper (chalcopyrite)-gold mineralisation occurs mainly within the magnetite-biotite-calcite ¦ pyrite matrix of a 250 m + 300 m pipe-like breccia body. The breccia pipe comprises two anastomosing lenses separated by a lower grade, clast-supported breccia zone. Several anastomosing brittle faults affect the macro-geometry of the orebody. Copper grade is proportional to the degree of matrix support in the breccia. The July 2002 Ore Reserve was 88.7 Mt @ 1.0 per cent Cu and 0.5 g/t Au. Resource estimation at Ernest Henry is based on a large database of predominantly diamond drill hole information. Drill spacing is typically 50 m + 50 m. Ordinary kriging is used to estimate Cu, Au, SG and IST (oxidation indicator) into model parent cells of dimension 20 m E + 20 m N + 16 m RL. The block model is comprised of five geological-geochemical domains represented by 3D wireframe surfaces. Zonal control, where samples and blocks are assigned the same domain number, is used to control grade estimation. The geometry of the domains defines hard grade boundaries across strike and soft boundaries along strike A Deep Drilling Project was initiated in August 2002 with the initial aim of testing the down-plunge extension of the orebody to a vertical depth of over 1 km. The encouraging intersections to date have resulted in a significant increase in the mineÆs open pit Mineral Resource together with the identification of an underground Mineral Resource. Added benefits of the project included an expanded and updated geological legend and an improved understanding of the host geological sequence.

Jan 1, 2003

BHP Steel International's Newcastle blast. furnaces have operated since their caimissioning on cake based on local low rank coals. In the early 1960's Newcastle coke was believed to be the weakest in the world. Newcastle coke now supports a blast furnace operation with a productivity of 2.1 t/d.rn IV, a fuel rate of 490 kg/t and a coke rate of 415 kg/t. This coke is nuudv from blonds of lcxni and southern Sydney basin coals with blend Ro nex in the range 0.94 - 1.01. Blast furnace performance in periods of differing coal blends is conjured. The relationship between coal aril coke quality indices and blast. fin-mice perforrnarcc.e is discussed as well as the relevance of conventional coke tests. New BHP coke tests are referred to.

Jan 1, 1987

By S K. Michelic, M Schickbichler, A Kharicha, E Karimi-Sibaki

The requirements for the controllability of metallurgical processes are increasingly becoming the focus of both industry and research. Advances in this field of research not only impact the stability of processes but often also influence the quality of the final product. One important way to examine processes in-depth, and thus show potential for improvement, is to describe them using physicsdriven models. In metallurgy, thermodynamic and kinetic descriptions of interactions between individual components of a system are often used to describe and analyse important metallurgical phenomena across the entire process. However, for the creation of physics-based models, boundary conditions and process variables must be implemented to enable a description that is as realistic as possible. The collection and generalisation of boundary conditions and process variables is, therefore, an important step towards functional models. The focus of this study is the determination of mass transfer coefficients between all components in a steel/slag/refractory system. For this purpose, experimental and theoretical methods are applied. Laboratory scale experiments are carried out in an induction furnace, and the mass transfer coefficients of the defined steel/slag/refractory system are calculated from changes in the chemical composition of the various components. Additionally, a calculation of the mass transfer coefficients based on dimensionless quantities is carried out. By comparing the values of the mass transfer coefficients determined theoretically and those determined experimentally in the trials, the suitability of the calculation is examined. The collection of mass transfer coefficients provides essential findings for future kinetic descriptions of inclusion modification based on the effective equilibrium reaction zone (EERZ) approach.

Aug 21, 2024