Search Documents

By L Soares, W T. Hennies, F Fujimura

A methodology of environmental performance evaluation in mining developments is proposed, as well as guidelines and procedures for obtaining information to improve their environmental performance. Environmental performance is the results of the mining activities and their relation to environmental issues. If this evaluation is carried out on an on-going basis, it is possible to anticipate or to identify the formation and development of an environmental impact in its early stages. Evidence or trends identified by environmental evaluation provide valuable information to prevent further damage. The proposed methodology is based on the significant environmental aspects of a selected monitored job site by environmental indicators which are then compared with previously defined environmental criteria and targets or goals. The methodology procedures also take into account the environmental accounting of the investments and expenditures.

Jan 1, 2003

By van der Walt TJ, van Deventer JSJ, Reuter MA

Owing to their complexity, many metallurgical processes are difficult to model fundamentally, and as a result more attention has been focused on the use of artificial intelligence techniques to simulate these processes. In this paper recent advances in the use of neural nets to model processes not amenable to conventional methods are discussed. These include the application of a new modelling methodology based on the use of neural nets for the dynamic simulation of metallurgical processes, the use of conventional techniques in conjunction with neural nets to simulate gravity separation circuits, as well as the detection of gross errors in variable measurements by means of a neural net representation of the relation between measurement and constraint residuals.

Jan 1, 1993

By Moffatt G

Approval to operate Longwall No. 7 at Appin Colliery in 1979 was granted pursuant not only to the usual statutory provisions, but also that an adequate means of drainage of methane gas be incorporated. A methane drainage plant was subsequently designed and constructed some two km from the pit top at the site of the Colliery main upcast and down cast shafts. Modern plants of this nature are completely automated using programmable controllers and computers to provide control and management reporting functions. Complex mechanical systems are installed to extract the gas and in handling and storage processes. Gas utilisation plants exist which can generate power from methane. These plants are further enhanced by harnessing waste heat produced in the generation process. The installation, automation control and monitoring of these plants incorporates many facets of engineering from high voltage power supply and computer technology to complex gas handling procedures used in gas compression storage.and generation of electric power.

Jan 1, 1982

By Hikosaka A, Chiba A

In a fundamental study of the physical chemistry of steelmaking slag, equilibra bet- ween hydrogen-water vapour gas mixtures and liquid slags contained in solid iron crucibles have been measured for four binary slags, FetO-CaO, FetO-Si02, FetO-TiO2 and FetO-Al203 at 14000C. From the data, the activity of iron oxide and the ratio of ferrous and ferric ions (A = Fe3+/Fe2+) were calculated for the slag composition. The best ionic model is found to be that based on regular solution of cations. The oxygen distribution between slag and metal is quantitatively expressed by this model over a wide range of slag composition.

Jan 1, 1980

By Klenowski

Rational design of layouts for longwall operations is greatly facilitated by use of an accurate and economical method for predicting stresses and displacements. The displacement discontinuity method (a form of boundary element method) is based on replacing actual excavation geometries by thin slits of the same plan area. This approach allows three-dimensional stress- analysis at a fraction of the cost of alternative methods. The analyses can be readily performed on economical microcomputers, putting the analysis capability within the reach of mine-site personnel. This paper describes investigations associated with the German Creek Central Colliery, the first longwall operation in Queensland's Bowen Basin. The material properties used in the model, in particular the rock mass and goaf properties, have been 'tuned' to fit stress measurements obtained during extraction of the first and second longwall panels at the mine. The study shows that model predictions based on suitably scaled anisotropic rock strata properties are in good agreement with the stress measurements made to date. This model predicts average chain pillar loads significantly higher than predicted by models based on United Kingdom conditions. A working chain pillar design method is proposed using average pillar loads predicted by the numerical model and ultimate strength characteristics given by Bieniawski's formula.

Jan 1, 1988

Long-range side-scan sonar and conventional geophysical data for the Peru Trench region (8`S-15¦S latitude) have been analysed. The data show that the Peru Trench is a site of sediment subduction where bending-induced normal fault-ing of the Nazca plate plays a key role. The sediments are continually removed from the trench axis region by their inclusion in normal fault-defined void spaces, such as grabens. In the process of subduction, the sediments are often offscraped, folded arid kneaded temporarily at the base of the shoreward trench slope. The subduction complex comprising such sediments is narrower than 20 km and its volume remains more or less constant due to regular removal of its contents along with the down-going plate. Addi-tionally, morphology of the subducting Nazca plate is responsible for subduction erosion of the South American plate, where the horst blocks cause tectonic erosion by abrasion and the grabens provide a mechanism for removal of the eroded material.

Jan 1, 1990

By L Basnayaka, N Subasinghe, B Albijanic

"It has been recognised that the presence of clay minerals in ores adversely affect flotation performance. In this study, changes in rheological properties of the flotation pulps under normal operating conditions were studied with additions of bentonite and kaolinite clays at various concentrations. Zeta potential measurements were also carried out to determine the changes in surface charge due to adsorption of clay particles. The results showed that bentonite clay adversely affects floatability of pyrite while kaolinite clay had a lesser influence on flotation of pyrite. The addition of Ca2+ ions to the pulp containing bentonite modified the rheological characteristics and in turn improved the pyrite flotation. It was also observed Ca2+ ions suppressed the swelling properties of bentonite and altered surface charge properties of bentonite clay particles. It has been shown that the flow index affected the ultimate recovery and it may provide a means to monitor flotation performance in routine plant operations.Citation:Basnayaka, L, Subasinghe, N and Albijanic, B, 2016. Effect of Clay Rheology on Flotation of a Refractory Gold Ore, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

The Pasminco mine at Rosebery in north western Tasmania is a medium sized underground base and precious metals mine. In April 1992 a major wedge failure of approximately 5000 t occurred in the backs of a main access drive to the 18 level H Lens orebody. This collapse prevented access to 190 000 t of ore which had been scheduled for production in July - August 1992. At the time of the collapse, the mine was in a transition period between mining small pillar remnants of several other orebodies and developing to the new deeper J Lens orebody.The development at this orebody was behind schedule and it was necessary to find a cost-effective and timely alternative to a 75 m bypass drive around the fall area.A Lysaght- Fletcher multiplate steel arch was available on-site from a deferred surface road project and it was decided to use this arch to regain access through the fall area. Due to the danger of continued minor falls, the entire 18 m long, 3.95 m high x 4.5 m wide tunnel had to be assembled in the 4.7 m wide x 5 m high accesss drive and pushed into the fall area as a single unit.

Jan 1, 1993

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Kukla G. T

A Seam deposit User oriented Mine Planning System (SUMPS) was developed by The Broken Hill Proprietary Company Limited (BHP) at its head office in Melbourne. It is one of the computer mine planning systems developed by the Corporate Data Processing (CDP) section of BHP. To date it has been employed in the feasibility study of four coal prospects for the BHP Group, including Gregory in central Queensland - Ham and Van Hoorn (1978). It was also used in detailed short term mine planning for Gregory. A recent application was in the feasibility study of Saxonvale, a multi seam coal deposit in New South Wales with seams up to 20 m thick. The other two applications of SUMPS were also on thick multi seam coal deposits. Development of programs for the underground sub-section of SUMPS is continuing. SUMPS was developed and implemented on mini computers with graphics and plotting peripherals. The company's philosophy towards computing is one of centralized development and project planning, with transfer of hardware and software to site once the mine becomes Operational.

Jan 1, 1980

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

By Morsky P, Kalapudas R, Natunen H, Virtanen M

The development of autogenous grinding modification in Outokumpu, known with the name 'Outogenius Comminution', was 'reversed'. At first the metallurgists studied and tested tens of years autogenous grinding in detail in full scale circuits at the concentrators of the company. After the final solution already had been found, also a pilot plant was built and now finally, research work is under way to develop a special laboratory method for testing the suitability of ores for 'Outogenius Comminution'.

Jan 1, 1993

Companies involved in the mining industry are exposed to risks, referred to as corporate risks, as part of the business process. Directors and management should be aware of these risks and make appropriate business decisions to address each risk. If business risks are not addressed on a timely basis the consequences are likely to be serious and will adversely impact the ultimate success of the business.The key corporate risks are:Poor cash flow and treasury management. ò Incompetent or unmotivated staff.ò Poor product quality.ò Accounting systems that do not provide meaningful and timely information.ò Computer system deficiencies. ò Ineffective credit screening.ò Assets not adequately protected.ò New ventures undertaken that are either inappropriate or not adequately researched.Exposures to corporate risk should be dealt with by Directors and management by systematically identifying major risk areas and implementing appropriate internal and management controls to deal with such risk areas. Proper management controls and procedures include the setting of overall corporate objectives and policy, monitoring adherence to such policy, establishing early warning systems to highlight problem areas and maintaining security over assets.

Jan 1, 1990

By Lee M. F, Guilfoyle K

A large hard rock rib pillar was recently preconditioned at Mt Charlotte mine using a novel blasting technique. The motivation for trialling this procedure was a history of past pillar failures, with associated seismicity. Design studies had shown that a new proposed pillar would be at risk of violent failure, and preconditioning was used in an attempt to reduce this risk. Preconditioning by blasting involves physically modifying a selected zone of ground in advance of mining, then forming the pillar so that it incorporates that zone of ground. The modified rock in the zone is intended to allow extra closure (yield) of the pillar in response to mining-induced stress changes. The ground modification was done by tight firing a blasthole array to fracture the rock. The blast design comprised pairs of pre-split blastholes to create a series of short cracks across the target zone, followed by main blastholes to fracture the rockmass between each pair of cracks. A monitoring program was used to establish whether or not the preconditioning was effective. It included conventional extensometers, stress change cells and closure stations, plus a seismic monitoring system. To-date, stoping is complete on one side of the pillar and has just commenced on the other. Results show significant movements within the preconditioned zone and on geological structures in the pillar, as well as lower stress in the pillar compared to an adjacent non-preconditioned site. The preconditioning technique can be applied elsewhere, provided its purpose, mechanism and side effects are understood. Benefits are likely to include more assured production, and successful pillar recovery even in high stress situations.

Jan 1, 1995

By J Rutter, M NoppT

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. Ridgeway is an underground sublevel cave (SLC) operation mining approximately 5.6 Mt of gold-copper ore per annum. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Drawpoint recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Grade control at Ridgeway has been based upon sampling the ore from SLC drawpoint bunds using 15 kg grab samples combined to form 30 kg samples prior to assay. This large sample size was selected in an attempt to representatively sample the coarsely-sized broken ore, the samples collected having a nominal diameter of about 130 mm. The assay results for gold and copper from these samples are extremely variable and the usefulness of the results has been questioned by the mine, particularly given the onerous and OH&S hazardous activity of handling large sample masses. Granulometry testwork at Ridgeway confirmed the extent of the relationship of decreasing sample grade variability with particle size. Based on this relationship, drawpoint sampling tests were carried out using 9 kg samples sieved to -45 mm at the drawpoint site. The gold and copper results from the finer 9 kg samples were significantly less variable than those from the normal, coarser 30 kg samples. The variance reduction was similar to that predicted from broken ore sample theory for the selected sample mass and nominal particle size. This relationship therefore allowed Ridgeway to assess the sample mass and particle size required to achieve a particular precision. In addition to improving the precision, the reliability of assay results from smaller samples from the fine particle fraction for drawpoint control depends on the accuracy of the results. The assumption is that the grade of the finer ore is similar to that expected from the lot, or that if a bias exists, then the extent of this bias is acceptable and consistent enough to be accounted for in the grade control system. The distribution of grade with particle size and the reconciliation of drawpoint sample and mine results is currently under investigation.

Jan 1, 2005

Five Hypotheses are given for factors influencing long-run metals price forecasts. 1 . Geologists succeed when given the money. 2. Better understanding of a metals market depresses its price. 3 . Statistical techniques get forecasts wrong. 4. Long-run metals prices are related to crustal abundance. 5 . Economic cycles affect metals prices more than is realised. These are then framed within the transition between eras as influenced by apparent long waves in economic activity. Innovation surges during the transition between eras. The transition to the 5th Wave since the Indus- trial Revolution 200 years ago is now underway. Finally, price projec- tions are given both for the 5th Wave and 200 years from now on the assumption that a similar monetary measure to today will be then extant.

Jan 1, 1988

By McCarthy P. L

With production at Olympic Dam scheduled to commence in June 1988, it has been necessary to install a complete underground ore handling system capable of removing two million tonnes of material annually from the mine. The system comprises mucking from stope drawpoints, truck haulage to underground storage, primary crushing, conveying and hoisting. On the surface, material is conveyed to stockpiles at the Metallurgical Plant. Mining of the numerous special excavations within the system was incorporated into the mine's ongoing development program prior to the underground construction phase. Utilisation of a decline from the surface enabled versatile construction equipment to operate at the underground sites as well as simplifying the transportation and delivery of construction Materials.

Jan 1, 1988

The Warraua and Mount Poole Inliers form part of a discontinuous series of basement complexes in the northwestern corner of New South Wales. The Inliers comprise mainly clastic sediments of low metamorphic grade (Wonominta Beds) and minor sills, dykes and intrusives, particularly within the Mount Poole lnJier. The Warratta rnlier has received attention due to the occurrence of auriferous quartz-veins where reef mining activities havetaken place.The deformational history of the Warratta and Mount Poole Inljers is characterised by a continuous subhorizontally WSW-ENE directed compression. Deformation was associated with the development of NNW-trending and steeply west-dipping major faults, which bound or biscct the inliers. Chevron folds and a penetrative axial planar cleavage characterise the deformational architecture and document crustal shorterung of at least 40 per cent. In zones adjacent to the major faults and within pelitic and semi-pelitic uruts, a multiple deformational evolution becomes apparent, comprising two events (D1 and D2). Deformational structures considered significant in this study were the result of D1. Tight, northeast-vergent fold patterns FI' and associated axjal plane cleavage SI' and reverse dip-slip movements at major faults indicate early northeast-directed thrusting during D1. This was followed by dextral strike-slip deformation displayed by tight, recumbent folds, en-echelon fold patterns (F2'), a northeast trending crenulation cleavage (52'), and two sets of second order faults, the latter showing high angular relationship to the major faults. A final stage of the deformational history (D2) is represented by WSW-ENE trending kink folds (F2).Auriferous quartz veins, predominantly occurring within pelitic and semi-pelitic units, were generated syntectorucally during the early deformational event (D1) in the course of commencing development of cleavage (S2'). Vein textures point towards vein formation by repeated hydrauJjc fracturing and fracture healing (crack-seal process), and by simple accretionary vein growth. Folded pelite-dominated horizons, considered as low permeability units, are suggested preferential sites where migrating metamorphic Ouids pooled and were trapped, causing high fluid pressure.Hydraulic fracturing and vein precipitation was controlled by lithology and structural constraints such as cleavage.K-Ar dates of approximately 440 Ma (Benambran Orogeny) marking the peak of metamorphism, and coinciding with the development of cleavage S1', also indicate the time of auriferous quartz-vein formation. A period of deformation of at least 30 Ma is proposed for the development of cleavage S1', as constrained by K-Ar dating and the intrusion of a syntectonic granitoid, the Tibooburra Granodiorite.

Jan 1, 1992

By A Scrase, J Brereton

The Latrobe Valley is located approximately 150 kms east of Melbourne. Within a very small area there are 3 large brown coalmines and associated power stations, 3 large towns, and numerous smaller towns in the vicinity. The mines have been generating power for Melbourne and surrounds for the last 100 years, with two of the mines being owned and operated by the Victorian Government (State Electricity Commission of Victoria) prior to privatisation in the 1990s. All three mines were privatised with the expectation that the mine voids would be filled with water to become pit lakes, as the final landform/rehabilitation solution (Hazelwood Mine Fire Inquiry, Teague and Catford, 2016). It could be argued that until relatively recently, this was largely expected, by government and industry, to be the rehabilitation solution for managing the two key risks associated with the sites:  The geotechnical stability of the mine pits.  The prevention of fire – through covering coal batters with water. Transitioning away from mining economies requires collaborative, regional, innovative thinking with a multitude of stakeholders, from a wide range of government departments, industry, First Nations people and broader community. Closure planning and rehabilitation activities require a range of skills and experience, such as, closure planning, various scientific and engineering disciplines (pit water quality modelling, geochemical modelling, cover design, landform design, contaminated site etc), civil engineering, demolition etc. Some of these skills are similar, such as financial modelling, stakeholder engagement, contract and project management. But the majority are different to those required during the operational phase of a mine. These closure skills can also be lacking within government, with Departments more familiar with monitoring and compliance activities associated with operational facilities. Some key aspects that appear to be critical to planned successful closure are:  Collaborative regional and localised planning, with industry, government, community, First Nations and other industry, business leaders and entrepreneurs all involved in providing a smooth transition away from mining.  Well-defined and known regulatory pathways to achieve mine licence relinquishment assists in encouraging investment.  Appropriately skilled and experienced government and industry personnel.  Mining companies, who are committed to closure planning and provisioning from the earliest point in project planning.  Mine employees who are appropriately skilled and experienced in mine closure planning and implementation with access to all the relevant technical expertise required for the project. Areas like the Ruhr Valley in Germany provide good some examples of smooth processes that facilitate mine economies transition into new economies (World Resources Institute (WRI), 2021).

Aug 2, 2023

Determining the environmental consequences of green field projects is becoming an increasingly important component of new projects. Feasibility studies are regarded by potential investors as incomplete if a comprehensive Environmental Impact Assessment (EIA) has not been completed. These EIAÆs need to meet various local and international requirements in order to achieve bankability. Heavy mineral mining projects are often located in ecological sensitive coastal zones, and bring with them a suite of social impacts in the mainly developing countries within which they are usually located. This paper draws on experience gained in undertaking EIAÆs for heavy mineral mining projects in Kenya, Mozambique and South Africa, and uses these case studies to identify potential pitfalls. Important lessons include the need to initiate the EIA process as early as possible in the project, in order to develop management systems to mitigate the environmental impacts of exploration. Close and on-going consultation with affected communities is also seen to be critical to the success of the EIA. Proactive participation on the part of the environmental consultants with the project team and all interested and affected parties (IAPs) is important. An EIA commissioned later in project planning makes it difficult for the EIA to contribute in a positive manner to the project. Early engagement with environmental consultants allows the environmental assessment to develop from a report to an actual process, and to become fully integrated with project planning. The proviso is that an initial æfatal flawÆ assessment is required to identify any potential æshow stoppersÆ, in order to meet one of the important objectives of EIA, namely an assessment of whether or not the proposed project is the preferred development intervention in the study area. For more controversial proposals this may require the commissioning of a Strategic Environmental Assessment (SEA), which circumvents some of the limitations of the project level EIA. Whilst confidentiality is a constraint to full disclosure, an open participatory approach to public consultation is essential to add credibility to the EIA process and to gain, at least, the acceptance of the process from the majority of IAPs. Full disclosure is encouraged by organisations such as the International Finance Corporation, who acknowledge that good public consultation costs a lot of money, but bad public consultation costs a lot more! An open approach to disclosure presents understandable difficulties for proponents, as they are required to give up some of their control over the project, and to trust the social scientists engaged in the process. However, independence in the EIA process is critical to its success. This paper will highlight these and other issues by drawing on five case studies to identify lessons learnt, and explore the above themes in more detail.

Jan 1, 2001