Search Documents

By Schaap W

A test on Taylor's rule of mine life using published data on open pit porphyry copper mines confirmed that mine life is, on average proportional to the fourth root of reserve tonnage. Deviations from this rule-of-thumb occur to a large extent as variations between regions that are qualitatively explained in terms of differences in grade, infrastructural needs or special taxation effects.

Jan 1, 1984

By M Uceda, E Guerra, Y Choi, J L. Shepherd

In this paper we describe the leaching characteristics of pure gold in thiosulfate solutions that contain a known chelator; meso-2,3-dimercaptosuccinic acid (DMSA). The interfacial and chemical characterisation of the system was accomplished using both electrochemical methods and inductively coupled plasma mass spectrometry (ICP-MS) analysis after pure gold samples were exposed to solutions composed of 65 mM Na2S2O3, 1 mM NaOH and a range of DMSA concentrations. In the absence of DMSA, cyclic voltammetry revealed the onset of thiosulfate mediated gold dissolution, the degree of which was reduced at more positive potentials due to the formation of oxidised thiosulfate products on the gold surface. The addition of small amounts of DMSA (<10 ¦M) to the electrolyte resulted in minor changes to the voltammograms indicating a subtle interaction of the additive with the gold surface that may improve leaching. However, at higher concentrations of DMSA (up to 100 ¦M), electrochemical evidence suggests the formation of new oxidation products in solution as well as the formation of more compact monolayers of DMSA on the surface, which contribute to partial repassivation of the surface. The influence of DMSA on thiosulfate leaching of pure gold electrodes at the open circuit potential for a period of 90 minutes was tested and the corresponding gold leaching performance evaluated with ICP-MS analysis. Our data shows that small amounts of DMSA (1 ¦M) doubled the amount of total gold in solution when compared to the same study in the absence of the additive. However, higher concentrations (5 ¦M DMSA) reduced the overall amount of dissolved gold. These results may point to a mechanism where small amounts of DMSA improve leaching by adsorbing onto the surface in a highly defective monolayer that partially blocks or disrupts the formation of passivation products caused by thiosulfate oxidation, but excess DMSA can limit the leaching process itself by forming too coherent a monolayer on the gold surface.CITATION:Uceda, M, Choi, Y, Shepherd, J L and Guerra, E, 2013. Investigating the influence of meso-2,3-dimercaptosuccinic acid on thiosulfate leaching of bulk gold electrodes, in Proceedings World Gold 2013 , pp 207-214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By P Malkin, S Thomas, P M. Stone, D Kostyuk

In open pit mining, it is common that the bottleneck to productivity and profit lies in the truck-shovel mining operation, especially as strip ratios and mining intensity have increased with resource depletion and advances in mining equipment capabilities. This paper outlines a study of truck-shovel productivity using a new proprietary discrete event simulation platform for truck-shovel operations called MineDES. The study will specifically address the issue of whether truck queuing at shovels should be considered productive or not, and how mining engineers can determine the optimal truck fleet size for specific operational configurations.The MineDES simulation platform will be described and illustrated, highlighting the features that make it an appropriate tool for conducting the experiments at the heart of this study. The study encompasses a set of experiments, consisting of a number of simple truck-shovel operational scenarios for a benchmark open pit mining operation, which are simulated using MineDES. Each experiment is designed to highlight different factors, which are most important in calculating the ideal truck fleet size and for understanding the marginal productive impact of each additional truck added to the fleet. The scenarios will principally address the issues of how different types and levels of unscheduled equipment downtime and process variation, combined with the traffic delays/congestion arising in more intense mining operations, will affect productivity. The results of the experiments are interpreted using a simple fit-for-purpose cost and revenue model in order to highlight the indicative cost of over- or under-trucked configurations.The study has found that the optimal fleet size that maximises productivity and value will, in the presence of even small process variation, lead to non-zero trucks queuing at shovels on average. As process variations and unscheduled downtime events increase in the truck-shovel system, the required fleet size to optimise productivity and value increases. MineDES provides a convenient platform for quantifying this for real operations.CITATION:Kostyuk, D, Thomas, S, Malkin, P and Stone, P M, 2014. Is truck queuing productive?, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 267–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By L B. Zhou, S Li, B L. Wang, S B. Li, Q Wang

The rapid development in ChinaÆs metal mine resources has caused a series of mine environment problems such as serious ecological damage and environment pollution, and secondary geological disasters. The paper has reviewed ChinaÆs metal mine development, including current status and environmental situation, analysed existing problems in mine development and environmental management, and proposed corresponding countermeasures and suggestions.CITATION:Wang, B L, Li, S B, Li, S, Zhou, L B and Wang, Q, 2012. Current situations, problems, countermeasures and suggestions for ChinaÆs metal mine development, in Proceedings Life-of-Mine 2012 , pp 353-356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

RME has a vision for a new grinding plant operational paradigm made possible by RMEÆs fast, safe Mill Relining System. Some new liner designs can degrade SAG mill performance because of mill volume loss, ball strike (rotational speed limitations) and other issues often brought about by modifying liner design for maximum life and without a backward glance at metallurgical consequences. Freshly relined mills can initially produce as little as 80 per cent of their maximum throughput, that maximum occurring toward the end of the linersÆ wear life. RMEÆs proposition is to see new liners designed for maximum commercial performance. This may mean more frequent mill relines but with liners designed to yield optimum grinding, metallurgical and profitability performance, not maximum life. In other words, mill liner profiles and mill relining speed become key operational controls and not simply æmust doÆ maintenance functions. Taken to the extreme, liner profiles may prove capable of ætuningÆ a grinding plant for maximum profitability in any metal price environment. Following the introduction, the first section of this paper provides an update describing recent and significant developments within RMEÆs range of Mill Relining Systems, the enabling technologies which permit more frequent liner exchange without incurring additional downtime imposts. The second section outlines RMEÆs vision of a æliner profile versus profitabilityÆ commercial model, developed either intuitively or by using a combination of new measurement and modelling technologies. These new measurement and modelling tools provide the opportunity to predict the optimum commercial outcome, off-line in the virtual world, before committing to an expensive liner experiment.

Jan 1, 2007

The demands of the economy require larger manufacturing facilities using greater quantit- ies of raw materials which must be mined, handl- ed, stockpiled and recovered with efficiency and dependability. All over the world, mining com- panies, steel manufacturers, power stations and process plants are not only seeking but finding methods of increasing outputs and'reducing costs in the field of materials handling. In mining bigger continuous mining machines and shovels, larger trucks and crushers are digging and processing greater quantities of differing materials which have to be handled and shipped at rates once thought to be impossible. To implement such schemes demands the blending of a lot of diverse-equipment, mining machinery, bins, feeders, reclaimers and it is here that the belt conveyor assumes a role of ever increas- ing importance. Significant developments have taken place in the seventies with respect to conveyor belt transportation; not only in the systems but also in the components which combine to make such systems work efficiently.

Jan 1, 1976

By A T. Spathis, K E. Leslie, K R. Blay

Many open pit mining operations seek to control blasting-related movement of ore and waste to minimise loss and dilution. Tracking the movement of ore boundaries can result in the maximisation of ore recovery and minimisation of waste sent to the mill, thereby optimising the economic performance of the operation.A novel solution for tracking the ore–waste boundary location before and after a blast uses subsurface markers placed along the boundary with all measurements and scans conducted remotely from the blast block. Upon system activation, user-operated equipment on the surface determines the three-dimensional (3D) location of the subsurface markers.The patented system concept combines two electromagnetic mechanisms, magnetic positioning and radio frequency through-rock communications to enable remote battery-powered markers, buried within the rock to be accurately located in 3D space.Field trials at a quarry have demonstrated the system can comfortably handle over 100 subsurface markers with a complete scan, including set-up, taking less than an hour. Location accuracy for each marker in 3D space is better than 0.5 m at a range up to 50 m from the magnetic source, and the system has an overall operational range in excess of 75 m.CITATION:Blay, K R, Spathis, A T and Leslie, K E, 2015. A remote, rapid and accurate three-dimensional ore waste boundary tracking system, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 297–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T Goswami, G Brent

In response to concerns over greenhouse gas (GHG) emissions and an imposed cost in some jurisdictions, many mining houses have committed to reductions in their GHG emissions. However, mining faces particular challenges in this regard, notably from increasing strip ratios. Furthermore, mining activity around the globe is not expected to decrease in the foreseeable future as mineral demand is driven up by the aspirations of rapidly-developing nations. Novel approaches will thus be needed if any reductions in energy consumption and GHG emissions of mining are to be achieved.This paper presents some directions for the mining industry to pursue in reducing their GHG impact, focusing on the difference that blasting methods can make. Importantly, large productivity and revenue gains can also be realised from these methods.Key directions considered here include optimising resource recovery and quality through:reducing coal damage and loss from throw blastingrecovering thin coal seamsproducing cleaner coal with less dilution.Blast design can also significantly improve the productivity of surface mining by:improving muck pile shapingimproving mine equipment productivityimproving scheduling.We show how a particular blasting method can eliminate coal loss in overburden throw blasting and can lead to large increases in coalmine profitability. Thin seams that were previously wasted can also be recovered with this method. Furthermore, the method has been implemented to combine several separate drill and blast cycles into a single cycle, leading to productivity gains.An illustrative example is given to show how increased coal recovery can increase revenues and more than offset any potential GHG emissions liabilities. Overall mine energy and GHG emission intensities can thus be reduced.CITATION:Goswami, T and Brent, G, 2015. Blasting approaches to increase mine productivity and reduce greenhouse gas emissions in surface coal mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By K Williams, A Lavrinec, V Gurung, D Ilic

The moisture content of iron ore during handling can range from the dust extinction moisture at the point of arrival at the port to the transportable moisture limit at the point of loading ships for maritime transport. Moisture content and ore composition, specifically fines content, have a large influence on ore flowability. Typically, elevated moisture can result in bottlenecks, downtime and lost productivity due to build-up, conveyor carry-back and blockages, increasing maintenance costs. On the other hand, low moisture can result in increased dust emissions influencing the environmental footprint and product losses. Managing the use of water across the supply chain is therefore critical for service life of equipment, productivity, but also has environmental and social impacts, affecting the social license to operate. Previously, experiments have shown that oscillations induced in iron ore during handling and transport can result in movement of moisture through the ore. This kind of moisture migration depends on the nature of these oscillations, such as the undulation of idlers during conveying, the inherent ore properties and the initial moisture content. Moisture has been observed to move either upwards and/or towards the bottom of the burden. These effects can be exploited to remove excess water from the ore influencing handleability and operation, however, the actual mechanisms of moisture migration are currently poorly understood. The study presented herein involves the use of simulation to examine moisture and ore interactions. Simulations using discrete element method (DEM) and coupled with smoothed particle hydrodynamics (SPH) are implemented to investigate the behaviour of moisture in wet ore in the presence of oscillation. This is conducted at a fundamental level first using glass beads and water which is then compared to iron ore at high moisture content. The results of the modelling are discussed in view of experiments conducted.

Sep 18, 2023

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Aug 24, 2022

By A D. Campbell, G R. Power

The increasing availability of marker data in sublevel caving operations is changing the way draw can be managed to achieve positive recovery outcomes in these mines. This paper describes how marker data has been incorporated into flow simulations to help calibrate full mine ore recovery simulations for the forecasting and optimisation of recovery.Some flow modelling techniques do not use marker data, relying instead on the outcomes of physical and numerical experiments to guide assumptions about an idealised recovery flow shape. Other mines have access to marker trial data, but find it difficult to specifically link this marker trial information to their recovery models. This can make it difficult to create a link between the marker trial information and recovery forecasting and limits the potential value of the marker trials at the mine.In the simulations shown here, the marker rings are fully incorporated into the flow model, and can be tracked in the model. The model is compared against the real underground marker recovery information to give the user an indication of how accurately the flow settings in the model are reflecting the conditions in the experimental marker rings. An example of use of this system at an operational mine is included.CITATION:Power, G R and Campbell, A D, 2016. Modelling of real-time marker data to improve operational recovery in sublevel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By K Higuchi, K Saito, O Ishiyama

Iron ore in Australia is predicted to increase in its phosphorus content in the near future, which is detrimental to properties of steel product. Steelmakers are concerned by the content of phosphorus in iron ore will exceed limits for steelmaking and increase the converter slag ratio to molten steel, which will finally lead to a decline in competitiveness in high-grade steel production. In this paper, fundamental development of a dephosphorisation technique by reduction gasification is considered. Basic reduction examination was carried out using Australian and a synthetic model iron ore sample with phosphorus compound reagent, varying reaction time and composition of substances to find out suitable process condition for dephosphorisation. With successful lowering of phosphorus concentrations by gasification reduction of the iron ores, dephosphorisation was assumed and further elucidation works were carried out. More than 10 mass per cent of dephosphorisation ratio is obtained from Australian iron ore through batch-type 25 g furnace experiment using hydrogen as a part of reducible mixed gas. Lowering of phosphorus content occurred preferentially either in wustite or in another reducing zones, suggesting a relationship between reducing conditions to efficient dephosphorisation of iron ores. Another result of the fundamental experiment using a model sample with reagent is different dephosphorisation occurred with different reagents contributing to with unified reduction model for phosphorus, providing positive possibility for comparative evaluation, even if new morphologies of phosphorus in iron ore are clarified in future. According to these approaches, it is important to reduce iron ore efficiently and to avoid gasified phosphorus retaining and reattaching to adjacent iron ore particle at the same time. A kiln-type furnace is suggested to overcome previous technical issue, and additional experiments using larger rotating furnace were carried out for verification.

Sep 18, 2023

By J R. Hernandez-Aguilar, C O. Go, C Acuna

The gas dispersion properties that are the subjects of this communication include three measured parameters, gas superficial velocity (gas rate), gas holdup and bubble size, plus derived parameter, bubble surface area flux. Over the past ten years sensors to measure these parameters have been introduced and those originating from McGill University are briefly described. The sensors have seen extensive use in plant campaigns and experiences on four cell types at three sites are discussed. The impact of frother in controlling bubble size by retarding coalescence is illustrated, introducing the need to understand chemistry/machine interactions in interpreting gas dispersion results. An increase in Sauter mean bubble size (D32) with superficial gas velocity (gas rate, Jg) was found, which followed the empirical relationship where Do ~ 0.5 - 0.6 mm and C and n are fitted parameters dependent on the system (machine and chemistry). Following this trend in Db - Jg, consistent bubble surface area flux (Sb) - Jg trends are also observed. The trend in Sauter mean versus number mean (D10) is used to help interpret the nature of the distribution; as the means approach numerically, the distribution is narrowing. Analysing gas holdup versus gas rate shows both a dependence on location in the cell as well as cell position in a bank, factors which must be accounted for when comparing data from different plants and circuits. The instrumentation and methodologies being developed are presenting new opportunities for incorporating cell hydrodynamics into metallurgical diagnostics. A case study at one plant serves as illustration.

Jan 1, 2005

By Kato T, Eguchi M, Seino T, Itagaki K, Kimura T, Muto T, Shimizu T, Kobayashi T

Behaviour of minor elements in the dust collecting system connected with fluidized bed roaster for zinc concentrate was investigated by use of the bench scale experimental appara- tus. The dust collecting system was consisting of two dust chambers, hot electrostatic precip- itator, washing tower, mist electrostatic pre- cipitator, drying tower, absorption towers and potassium permanganate solution towers. Some volatile elements such as lead, cadmium and arsenic tend to concentrate in the fine calcine obtained in hot electrostatic precipitator especially in the case of the roasting with insufficient air supply. Special attention was paid to behaviour of mercury. In the roasting tests for plain zinc concentrate, it was considered that most mercury volatilizes at first as elemental vapour in the roaster, but with decrease in temperature of gas around a half of mercury forms compound, and both elemen- tal and compound forms of mercury were found in the gas stream. Elemental mercury is of course difficult to be trapped in the dust collecting system. To promote the compound formations, some additives for concentrate, such as selenium and halogens were effective, especially selenium of a few times equivalent to form HgSe repre- sented complete conversion of mercury from elemental to compound. To clarify the behaviour and removal mech- anism of mercury, various small scale laboratory tests were also carried out. It was confirmed that mercury sulfate formation is possible if temperature and flow rate are adjusted adequate- ly for gas stream consisting of 02-SO2-N2. To trap elemental mercury, various substances were tested, and excellent results were obtained with selenium. Satisfactory results were obtained with a selenium disc heated at 100 to 200¦C in a mercury containing gas stream. Also, applica- bility of scrubbing method with SeO2 solution was investigated, and the solution containing a few hundred ppm SeO2, 0.01 per cent additive and 6 per cent H2SO4 proved to be satisfactory.

Jan 1, 1980

By S Rogers, D Stead, E Eberhardt

The last decade has seen a major increase in use of the discrete fracture network (DFN) approach applied to cave mining problems, often integrated within more complex geomechanical simulations. Because the value of the DFN model directly depends on the quality and quantity of available field data, there is the need to apply dedicated mapping procedures to collect sufficient structural data at the required engineering scale. This paper attempts to address several key questions about DFN modelling; for example: are current methods for fracture mapping suitable for DFN modelling? What are the critical parameters that we need to measure and what do we need to change in the current practice? Particularly at the earlier stages of a cave project, engineers may have to account for the lack of appropriate data, which manifests itself in the form of increased uncertainty and the difficulty to characterise variability in an objective manner using a limited set of data. DFN models could in principle be generated using limited data by assuming statistical distributions for the sampled parameters; however, engineers would need to be aware of the implications that such limited knowledge (and increased uncertainty) would have on stability analysis, fragmentation analysis and mine design. When used correctly, a DFN approach offers practitioners the opportunity to:maximise the use of fracture data collected from mapping of rock exposuresgenerate more realistic synthetic rock mass modelsprovide estimates of natural fragmentation that also account for rock mass variability.CITATION:Elmo, D, Eberhardt, E, Stead, D and Rogers, S, 2016. Discrete fracture network modelling – importance of accounting for data uncertainty and variability, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 845–852 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G Lane

This paper discusses the factors that contribute to the cost effective design of a concentrator. Concentrator design and layout outcomes are functions of the team (engineer’s and owner’s) participating in each particular project. The benchmark for relatively modest projects was set in the 1980s and 1990s during the ‘gold boom’ when numerous cost effective plants were designed and constructed on a lump sum basis in a very competitive market. A number of factors contribute to lack of transference of the lessons learnt in gold plant design to concentrator design including established paradigms in the design and layout of concentrators, lack of experience in cost effective design, operator’s preferences for flowsheet and layout and simple lack of appreciation of the impact of plant footprint on materials quantities and resultant capital costs.Experiences with recent copper concentrator projects (both small and large) are used as case studies.

Aug 8, 2011

The role and policies of the Aboriginal Sacred Sites Protection Authority are described in conjunction with the provisions of the N.T Aboriginal Sacred Sites Act 1978. Comment is made on the application of the legislation and these policies to development proposals in the Northern Territory. A brief review of criticisms by both developers and Land Councils is provided together with responses to these Criticisms.

Jan 1, 1984

By Y K. Ji, B J. Chung

In recent years, the utilisation of ultra-fine ore in ironmaking has gradually increased due to the depletion of high-quality iron ore. The use of ultra-fine ore in the ironmaking process is typically energy intensive and leads to high CO2 emissions. The improvement of sinter reducibility is one of the methods used to reduce the environmental impact of using fine ore.In this study, a high-strength and high-reducibility sinter manufacturing process was investigated by controlling the sintering reaction. The key technology used in this method is the manufacture of mini-pellets by selective granulation equipment. The mini-pellets consist of iron ore, limestone and burnt lime and are designed to melt at temperatures below 1200°C. The molar ratio of CaO to Fe2O3 of the mini-pellets is 0.25~0.75. The 2~5 mm diameter mini-pellets are manufactured with burnt lime as the binding material.During the sintering of mini-pellets, goethite, which has relatively high reducibility, should be retained as residual ore in the sinter cake. The strength of the sinter cake was kept by the bonding reaction of the mini-pellets, which have a low melting temperature. This is the main principle of the reaction-controlled sintering method.The reaction-controlled sintering method manufactures a high-strength and high-reducibility sinter cake and increases sinter productivity by around 15 per cent using ultra-fine iron ore.CITATION:Chung, B J and Ji, Y K, 2015. Production of high-quality sinter by controlling the sintering reaction, in Proceedings Iron Ore 2015, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Roberts T, Firth B. A

A series of flotation experiments was carried out to study the interaction between the parameters of pulp density (mass per cent of solids in feed slurry) and frother addition (on the basis of solid mass feed rate). It was found that certain combinations of pulp density and frother additions caused large losses in yield. The interactive effect of these parameters can be primarily attributed to the total amount of frother added per unit of water. Consequently it is suggested that frother additions be made on the basis of water flow rate. As frother addition increased, in terms of the amount of frother per unit of water, yield increased rapidly but above an addition rate of about 10 g/tone it reached a plateau. Such results correlated well with qualitative visual observations of changes in bubble size and dispersion, with increasing levels of frother addition.

Jan 1, 1984