Search Documents

By Gooday PE, Brech GE

Ore reserve categories used by Pancontinental Mining fall into one of three fundamental groupings: Geological In Situ Reserves Mining Reserves Production Estimates The first of these describes the total reserve within stated parameters without implication as to its mineability. The second is that part of the Geological In Situ Reserve which is considered mineable under a specific mining plan. The third is the Mining Reserve adjusted with appropriate dilution and recovery factors and thus represents the best estimate of the tonnage and grade of production. This practical three category system mirrors the standard steps traditionally taken in ore reserve estimation and readily conveys the basis of the estimates. An important, but secondary classification can be added to qualify the level of confidence in these estimates using the terms: Proved (or Measured) Probable (or Indicated) Possible (or Inferred) These terms can be applied to any of the fundamental groupings, but it is generally implicit that the level of detail required to produce meaningful Mining Reserves or Production Estimates would require the basic Geological Reserve to be at a Proved or at least Probable level of confidence. The application of these classification systems by Pancontinental is illustrated by reference to the Paddington Gold Project. The methods of calculation are described including the use of geostatistics. Reconciliations of actual production with predictions from reserves are carried out monthly and annually. To date there has been an excellent correlation with Production Estimates, based on both manual and geostatistical calculations.

Jan 1, 1987

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

By King RP, Kientzler P

In recent years, ultrasonic comminution technology has been developed at the Utah Comminution Center. An ultrasonic grinding device was assembled and investigated. An ultrasonic transducer system has been significantly improved by using a special type of piezoelectric ceramic and preloading to 4.1 x le kPa to obtain maximum strength. The improved system provides constant and rapid vibratory promotion of fatigue fracture resulting in more effective breakage. The design principles for an ultrasonic mill are developed in this paper. Size reduction was successfully achieved in the ultrasonic nip-roll device for a variety of materials. Ultrasonic comminution has repeatedly demonstrated the capability of producing fine particles from a variety of materials. A comparison between ultrasonic grinding and dry ball milling of limestone showed that the ultrasonic device produced much narrower size distributions than the ball mill. This trend is especially obvious in the coarse size range where few particles remain, and in the fine size range where overgrinding is prevented. This behavior might have some interesting applications in areas other than mineral processing like powder metallurgy or material science where narrow and controlled product sizes are required for the successful elaboration of high-technology ceramics and glasses. Ultrasonic comminution has a significant advantage in the accurate control of the product size.

Jan 1, 1993

A novel fracture-plane control blasting technique with particular application in wall-control blasts in mines employing medium to large diameter boreholes is described. It consists of a string of nested holes, each nest consisting of a large diameter charge-hole flanked on either side by a small diameter satellite hole. Each nest is shown to be an analog of a pressurized hole with diametral notches along its length. This 'equivalent-notched' hole concept for generating controlled fractures along preferred directions has been successfully investigated in the laboratory and in the field. The technique has been used to generate controlled fractures on a quarry bench in highly jointed limestone. The resulting blasts with a 250 mm diameter central charge-hole and 50-75 mm satellite holes show that two nests of such holes almost 5 m apart could be joined by a single co-linear fracture. The design range of diameter ratio between charge-hole and satellite hole is 3 to 6 and spacing is 3 to 5 charge-hole radii. With careful matching of explosives and decoupling, and combination of diameter ratio and spacing, it would be possible to connect two nests of such holes more than 20 charge diameters apart by a single controlled fracture plane. The relative merits of the technique against existing wall-control blasts are discussed, and guidelines for practical fracture-plane control blast designs are discussed.

Jan 1, 1990

By Jowett A

To compare open circuit lead primary rougher results at Mount Isa Mines Ltd., eleven surveys were made over five weeks of plant operation with varying ore sources, including a specially hauled sample of 100% Black Star ore. Three of the surveys which represented extremes in performance were selected for sizing, cyclosizing and assaying for lead, zinc and iron. A comparison of the flotation kinetics has revealed the similarities (including common problems) and differences for the surveyed ores. The concepts of entrainment and collectorless flotability are used to aid interpretation of the kinetic data.

Jan 1, 1978

This paper describes the application of a three-dimensional finite element modelling tool to help assess the stability of a highwall at a Central Queensland mine following the weakening of its base due to highwall mining. With traditional stability assessment techniques, likely failure modes are identified on the basis of previous experience and structural, sedimentological and geomechanical data and a mechanistic analysis of these individual modes is performed. The value of the full three-dimensional model over these traditional techniques is that it provides a coherent approach to assessing highwall stability without the necessity of initially deciding upon the dominant failure mechanism and gives a useful adjunct to the traditional tools. The three-dimensional model assumes the rock mass is made of elasto-plastic blocks, incorporating possible planes of weakness, separated by near horizontal joints. The model includes the relaxation of stresses due to the excavation of the highwall and incorporates estimates of blast damage near the highwall surface

Jan 1, 1995

This paper introduces a new, safer bulk emulsion loading system for underground mining operations. The features and benefits of the equipment, along with the use of Dyno Nobel Inc patented gassed emulsion technology, is summarised in the application of a stope blast with very difficult and complex ground conditions. The paper describes methods used to optimise the amount of energy required to break the ore while protecting the integrity of the surrounding backfilled pillar.

Jan 1, 2004

By Slater R

The initial planning and detail design phase leading to the development of a 7.5 m internal shaft to service the deep 3000 and 3500 copper orebodies at Mount Isa, Queensland is well advanced. The choice of internal shaft access was made over alternative methods such as a decline from existing levels and borehole hoisting. The resulting access development requirements and shaft configuration for production have been determined. Several techniques are being studied for shaft development. These include the application of blind shaft drilling and large hole reaming methods as well as conventional sinking techniques. As the 3000/3500 Orebodies extend from 1000 metres to more than 1800 metres below the surface, high stress conditions and ground temperatures ranging from 45CC to 62CC are anticipated. The effect of these on the methods being investigated to create a favourable working environment will influence the final choice. Exploration diamond drilling is in progress to confirm the geology of the orebodies so that planning for their extraction including refrigerated ventilation concepts can proceed.

Jan 1, 1982

By Bowling K. McG, Hamilton J. D G

The influence of three important para- meters which affect the induration of iron-ore pellets, viz temperature, time, and lime content, have been assessed in terms of internal pellet structure and commonly-used pellet quality criteria. The pellets studied were produced from a typical hematite ore from the Pilbara area of Western Australia, using a 25 cm dia. pot-grate test rig. Isothermal laboratory induration tests were conducted in accordance with a statistically-planned programme. The internal structures were studied by optical microscopic examination of polished sections of the test pellets. The effects of SFCA (silico- ferrite of calcium and aluminium) and slag formation, matrix consolidation and grain modi- fications were studied, and have been related to pellet properties and to the time/temperature histories produced by the firing conditions chosen. The implications of the data for commercial pellet plant operations are discussed.

Jan 1, 1974

By Xaykhamphoune, Ward B

Draglines have been used exclusively for primary overburden stripping at the German Creek Mine complex in central Queensland, where coal has been extracted from a series of ten open cut pits working seams of the German Creek Coal Measures. Due to the dip of the seams, most of the pits have now reached the limit of current economic viability and the emphasis has switched to underground extraction using longwall methods and to a new area of open cut reserves in the nearby Rangal Coal Measures at German Creek East. This area is characterised by weak Tertiary overburden, relatively steep dips and low strength intraformational shear planes at the top and bottom of the coal.The first pit, with a maximum depth to coal of 15 m at the low wall, avoided any major slope failure through use of scrapers to excavate the boxcut and dump the spoil away from the low wall. However, this method was not considered economically viable for the second pit where low wall depths reached 44 m. Following geotechnical investigations the boxcut was divided into a number of zones depending on depth of cover, dip and thickness of Tertiary clay. Slope stability was assessed for each zone using several analytical techniques to ensure that dragline mining would be acceptable. Slope design parameters incorporating various stabilisation techniques, notably an updip trench backfilled with competent spoil to form a low wall buttress prior to excavation of the boxcut panel, were successfully integrated into the mine plan after careful consideration of the complex scheduling to minimise rehandle.

Jan 1, 1992

During the last 12 years the dominant theme at Mount Isa has been production expansion. Production rate of 3,200 tons per mine day in 1953 increased to 11,000 tons per mine day in 1960, completing the first stage of the programme. The second stage is still in progress. It is planned to increase production of lead and copper ores to 19,500 tons per mine day in 1968.Current mine workings comprise an area 2 miles long and 1/2 mile wide, the deepest production level being 2,000 ft below surface. During the next 10 years it is anticipated that mining will be carried out to a depthof 3,200 ft below the surface. The rapid extension of the mine has necessitated frequent re-appraisals and modifications to the primary ventilation system, and a system with considerable in-built flexibility has gradually evolved. Since 1953, volume circulation has increased eight-fold to approximately 2,400,000 c.f.m.To suit various mine operating requirements, a combined pressure-exhaust system of ventilation was adopted.The usefulness of this system is at a maximum when the fans installed permit ready changes in the location of the boundary between adjacent spheres of fan influence.Air flow through openings to the surface can be controlled or used as required. This feature is considered necessary for a mine where underground workings are comparatively shallow and caving to the surface willoccur.A major heat problem exists due to climate conditions, high geothermic gradient (one degree Fahrenheit in 95 ft), and oxidation in leached and brecciated areas.Because of this, quantities of air far in excess of the minimum requirements for dust removal are required to ensure satisfactory environmental conditions. In assessing fan pressure, consideration was given to 1. the mine resistance, and the requirement for pressure differential capability,2. the pressure requirement for deeper mining, with due allowance for booster fan use where appropriate,and3. the desire to avoid fan operation at pressure duties above the region of peak fan efficiency.The latter feature provides a safety margin between maximum operating pressure and the stall point of the fan.

Jan 1, 1967

Longwall mining in Australia is approaching maturity. Longwall production from 'state of the art' Australian longwall mines now rivals similar US based longwall operations. Regrettably however, Australian gate road development rates in general fall short of the required development to longwall production ratios that are required to sustain annual longwall production capabilities. By contrast, most US based longwall mines achieve the required development to longwall production ratios to sustain their longwalls. This is despite many having to drive three heading longwall panel gate headings to meet regulatory requirements.

Jan 1, 1998

DURING the four years, 1922, 1923, 1924, and 1925, China produced the following quantities of non-ferrous metals and ores: Antimony Products - 67,869 (long) tons. The production for 1925 was 20,869 tons, of which 80% was regulus, 14% crude,and 6% oxide.Arsenic (White) - 4200 tons. The production for 1925 was 1200 tons, but only 90 tons were exported, some 25% of which to Hong-Kong, France, and U.S.A. each, and the rest in small lots to other countries. Domestic consumption was 1110 tons, and thelocal price for "cake" was around £47 per ton on 1925 exchange.Arsenic Ore (Realgar) - 1400 tons.Lead Ore (Galena) - 44,853 tons. The production for 1925 was 10,853 tons, of which 16%, produced in Korea, went to Japan, and 84% produced in Hunan, went to Europe.Manganese Ore (Pyrolusite) - 142,567 tons. The production for 1925 was 42,567 tons, of which 94.3% went to Japan.Tin Ingot - 33,480 tons. In 1925 the exports to Hong-Kong were 8880 tons of usual rough tin of 94% to 96%. Most of this was refined to No. I Chinese quality of 99.3% and exported to U.S.A. and Europe, owing to the good price ruling.Sulphur - 12,000 tons. Sulphur is included in this list in order to explain how its production led to the discovery of some other ores.Wolfram - 19,668 tons. The production in 1925 was 5868 tons, most of which came from the Quee Mee mountain district in South Kiangsi, from the detrital deposits. Civil disturbances prevented the usual output from Hunan border.Zinc Ore (Blende) - 134,190 tons. Exports for 1925 were 34,190 tons of low-grade ore, averaging 30% zinc, 14% lead, and 7% silver...

Jan 1, 1927

By R N. Humphries

The aim of this paper is to question the need to develop bespoke monitoring and assessment methodologies and criteria, thereby ‘reinventing the wheel’, when designing and assessing the success of important natural habitat and ecosystem restoration schemes at mine sites in the UK and Australia. It draws attention to the existence and applicability of the Phase I Habitat, National Vegetation Classification (NVC) and Condition Monitoring methods in the UK and similar approaches used in Australia. These are long accepted established methodologies and have published accounts for describing, assessing and managing natural vegetation communities, habitats and ecosystems. They are often used at the environmental impact stage, but seemingly rarely, if at all, in restoration design and management at mine closure. Their application to mine restoration and closure is illustrated and discussed by reference to a surface coalmine in South Wales, UK.It is concluded that the application of a combination of the Phase I Habitat, NVC and Condition Monitoring methods is highly relevant to the expectations of the Convention on Biological Diversity (CBD) and its implementation in the UK, and probably in Australia too. The methodology and criteria described could be incorporated into the guidance and specified in the mining permits so that there is clarity as to the expectations and requirements for monitoring and assessment for bond release. Their use could be of wider application where there is a requirement to assess the success of restored CBD assets and ecosystems.CITATION:Humphries, R N, 2014. Why reinvent the wheel when there are established methodologies to aid the design and assessment of restored natural ecosystems on mined land?, in Proceedings Life-of-Mine 2014 , pp 675–692 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

There are serious problems in forecast- ing accurately and achieving this goal depends on good quality information, correct assumpt- ions and sound analysis. planner. The forecaster must focus attention on a number of key areas of interest. These areas include major economic trends and changing GNP structure, consumption time series, end-use consumption patterns and substitution potential, accurately updating data bases (up to 5 years ahead), random factor estimation and examination of both long term and secondary mine potential. While metal price forecasting has suffered due to recent uncertainties, with increased importance on planning tools and cost analyses, it is still a necessary function. Forecasting is subject to the real world and the metal industry is made up of imperfect markets in a dynamic state. The real world provides the challenge to improve the accuracy of forecasting.

Jan 1, 1983

By Palmer W. T

The successful re-opening of the Cobar min- eral field was dependent upon the success- ful introduction of highly productive, low cost mining. Mechanised cut and fill stop- ing with incline access was selected for the C.S.A. mine because it permitted flexi- bility, complete primary extraction with no secondary pillar recovery, minimised dilu- tion and oxidation, a minimum of pre-pro- duction development and because diesel powered load-haul-dump (L.H.D.) units were proving reliable and highly productive in the U.S.A. Although L.H.D. vehicles are the key to the success of the mining method, four other main groups of vehicles are utilised in the mine - trucks, scaling vehicles, ser- vicing vehicles and specialist vehicles. The operating requirements at the C.S.A. mine are more stringent than those encount- ered in many other underground mining oper- ations. The first L.H.D. vehicle used at Cobar - the Transloader - had considerable difficulty in loading and discharging coarse production ore. The Wagner ST5 Scoop Tram performed this duty much better. However, the first generation Scoop Trams were not robust enough to withstand the heavy duty and many modifications were necessary before acceptable availabilities were obtained. Similar modifications were necessary for the Eimco 916 vehicle but the Eimco 915 unit came much closer to meeting the duty requirements. Eventually Cobar technical personnel design- ed a L.H.D. vehicle to meet specific C.S.A. mine conditions. These units have proven most satisfactory. Over 8 years of operation the underground vehicle fleet has become a proliferation of vehicle types. A standardisation pro- gram has been initiated based upon common prime movers being mated with "trailer" units to serve specific functions. Standardisation will reduce inventory levels and facilitate training of operating and maintenance personnel.

Jan 1, 1973

By S Robson, T G. Blenkinsop, S C. Dominy

Golden Pig mine is in the central part of the Southern Cross greenstone belt within the Archaean Yilgarn craton. The mine has produced approximately 2.5 Mt of ore at 5.7 g/t Au to yield approximately 450 000 oz. The majority of gold mineralisation is hosted within extensively deformed and quartz-veined BIFÆs. In addition to the BIF-hosted mineralisation, an increasingly important part of the resource lies in the Taurus Lode, which is a N-NNW-trending amphibolite facies shear zone. The Taurus Lode lies within a continuous shear-zone that has a moderate to steeply WSW dipping foliation, and a mineral lineation of biotite, amphibole and pyrrhotite plunging consistently 10¦ S. Drive faces, subperpendicular to the foliation and lineation, consistently show evidence for syn-mineralisation reverse shear. Exposures parallel to the mineral lineation and perpendicular to the foliation reveal both sinistral and dextral asymmetries. These characteristics suggest that the vorticity axis of the Taurus Shear Zone is parallel to the mineral lineation, and that the simple shear sense is reverse. This geometry can arise when there is a major component of flattening across the shear zone, which may be due to interference between two adjacent granite domes. The BIF-hosted lodes plunge consistently 15¦ NNW coincident with the intersection of the axial planar cleavage of the regional folds and the Taurus Shear Zone. However, where the penetrative shear characteristics control the orientation and geometry of the mineralisation, oreshoots plunge SSW, parallel to the stretching and mineral lineations within the shear. The SSW plunge of strike extensive and laterally confined high-grade, economic ore shoots within the Taurus shear is fundamental to defining the economic mineralisation within this lode. Identifying the zones of maximum continuity and establishing the optimal position for future development will maximise ore extraction.

Jan 1, 2003

By P Cherepanskiy, G Elphick, R Hus, C Perring

When an iron orebody nears its end of life, the extracted material can become increasingly problematic to handle. Higher moisture content occurs as larger portions of originally-below-water-table material is mined, which in some deposits is accompanied by further changes in physical and/or chemical properties present along the edges of the orebody. Plant delays related to problematic material have affected all of BHP’s mining hubs to various degrees. Following the recent successful work in Yandi, where the development of an index to quantify the handleability of channel iron ore deposits resulted in an increase in extracted volumes and an extension to the expected life-of-mine, the value of implementing similar indices for bedrock iron ore deposits has been recognised. A materials handling index has been developed by combining observed empirical relationships between material properties and processing plant performance. Indices for each deposit were further refined and optimised by implementing a back-testing strategy which facilitated an understanding of what weighting or scaling each of the contributing components should carry to yield the highest success rate of predicting actual delays at a given plant. Currently materials handling indices are deployed to all mine sites and are made available in block models as well as calculated for individual blasthole and production samples. Values in block models are obtained by predicting the required properties using machine learning models, whereas hyperspectral data is used to ‘measure’ some of those properties on a sample level. This paper discusses the work that has been undertaken to obtain materials handling indices, the testing that has been done to optimise them, and what processes have been developed to ensure the best metrics are being used in the different planning and scheduling horizons to optimise extraction.

Jun 22, 2022

The investigations described in this paper aim at the development of a new impact mill. The objective is to produce particle size distributions below 10 .tm without using an air classifier. Circumferential rotor speeds of up to 200 m/s are strived for.

Jan 1, 1993

By Campbell Brown G A

IN 1904-5 diamond drilling operations in the Mount Morgan mine proved the presence of some millions of tons of rich copper-gold ore, averaging about 45%to 50%silica and 22%Fe as sulphide. To smelt this ore in blast furnaces, without previous concentration, large quantities of basic flux were required. Unlimited quantities of cheap limestone were available at Marmor, on the GladstoneRockhampton railway, 50 miles from Mount Morgan, but the supply of iron flux was a more difficult problem. Smelting Operations started with one furnace in January, 1906, using as flux low-grade sulphide ore from the mine, containing very little silica. When the second furnace was blown in this was supplemented by ironstone from small deposits in the immediate district. It was recognized that these sources of supply would be insufficient to keep the full plant going after the third furnace had been blown in. Accordingly, the deposits at Kabra and Mount Etna were opened, neither of which proved capable of supplying the quantity required-viz., 1000 tons per week. Negotiations were meanwhile being conducted with the Marble Island Iron and Limestone Co. to obtain the right to mine at Iron Island, where a sufficiently large deposit was known to exist. Shipments from this source commenced in January, 1907, and ceased at the end of July of this year, when the metallic flux from...

Jan 1, 1911