Search Documents

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By D J. Brake

Most mine ventilation engineers are involved in ventilation planning and design in some capacity. Ventilation modelling software used by a competent experienced ventilation engineer is extremely useful in developing good ventilation designs by allowing assessment of a wide range of potential options. Unfortunately, ventilation modelling undertaken by persons who do not have sufficient experience or knowledge usually results in a façade that covers up a fundamentally unsatisfactory design. Ventilation models are produced for a wide variety of purposes including: fault-finding of a problem area in a mine and options analysis for resolution of such problems; a complete review or optimisation exercise of an entire mine’s ventilation system; or a much longer life-of-mine type of study. Models can be intended as the basis for studies with diverse purposes such as primary shaft or airway sizing, primary fan specification, examining re-entry times after blasting, resolving leakage or recirculation, or investigating the impact of fires or underground climate or cooling requirements. The concepts of ‘materiality’ and ‘fitness for purpose’ are essential to developing or using a ventilation model and serious mistakes have been made in wrongly using a ventilation model for purposes for which it was never intended, often because it is simply the most recent model on the mine site. Mistakes at this level often translate into faulty ventilation strategies and inefficient or ineffective use of scarce capital for ventilation projects. Validating a ventilation model is a time-consuming and expensive process and not every model must (or even should) be fully validated to meet the objectives at that time. This paper discusses the application of quality assurance in ventilation planning with particular respect to the ‘basis of design’ (BOD) as well as the standards for validating a ventilation model. It also provides a recommended way of dealing with non-conformances in measured versus modelled values of critical parameters in the model.CITATION:Brake, D J, 2015. Quality assurance standards for mine ventilation models and ventilation planning, in Proceedings The Australian Mine Ventilation Conference, pp 221–228 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Ta’ala, M Handyside

Mechanical sampling from conveyors has historically been a staple in the iron ore industry when information related to chemistry, sizing and moisture is required. In order to comply with ISO 3082:2009, samples can be taken either on a mass or time basis provided no bias is introduced by periodical variation in quality or quantity. With the introduction of mechanical sample carousels, you also have the opportunity to collect samples on a mass or time basis. In order to optimise automatic sample stations in a changing production environment, BHP Billiton Iron Ore (BHPBIO) has developed a simulation model that enables the various combinations of mass–mass, mass–time, time–time and time–mass to be investigated.The sample station model can utilise actual (variable) feed rates to achieve high resolution and enables the simulation of sample size variation. Cutter speeds and other settings can then be adjusted to better optimise the performance of the sample station with regards to optimal sample size as well as ensuring the sample station is in compliance with ISO 3082. The model can also assist process engineers in adjusting settings to better optimise the sample station and reduce unwanted events such as blockages. The model can be easily modified to conform to various sample station designs. This paper demonstrates the use of the model and the benefits that can be achieved.CITATION:Handyside, M and Ta’ala, J, 2014. Simulating time versus mass basis?sampling, in Proceedings Sampling 2014 , pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

Confirmation that acid drainage (AD) was a significant environmental issue for the Australian minerals industry came in 1992 with the first national workshop on the topic. Subsequently the extent of AD was documented in a national survey published in 1997. The recommendations arising out of that survey served as a platform for actions by government, industry and industry-support organisations such as the Australian Centre for Mining Environmental Research (ACMER) to enable more effective prevention and management of AD. This paper briefly documents the extent of AD in the industry, the government regulations and guidelines for AD management, industry initiatives, the role of ACMER and other organisations in assisting industry through research and technology transfer, and the efforts being made to deal with AD at derelict mines. Future management of AD in the industry will be assisted by the linkage of Australia (through ACMER) into the International Network for Acid Prevention (INAP) which is facilitating the interchange of knowledge on AD as well as coordinating global research on the topic.

Jan 1, 2003

By R Stead

So many ceramics look the same, but are they?In the past 20 years, there have been significant changes in the materials available, as well as changes to the supply chain, for ceramics used in wear applications in the hard rock mining industry. The biggest change in supply has been from the Chinese market, with many suppliers promoting their products as æstate of the artÆ. Some of them are state of the art, but are they all? There will be some concluding remarks in this respect.There are still some outstanding new developments coming from the more traditional suppliers and these should not be ignored. However, as an end user, how can one be sure that the product received meets the technical specifications of that material?This paper will address some of the questions on how to differentiate between different materials by giving a technical overview of the current (but not exclusive) range of popular ceramics, plus incorporating how these ceramics are used in process plant products by presenting case studies. The presentation will include technical data coupled with micrographs of various ceramics to illustrate just why they are different.It will also be shown that by careful selection of the wear material, it is possible to gain significant benefit when using superior materials in an ore processing plant. The impact of cost of the products, life, process efficiency, and reduced maintenance costs will be considered using cyclone components as an example.The properties (including the microstructures) of the various ceramics will be compared to the application in order to get some understanding of what is considered good or bad.Misra and Finnie (1982) summarised their paper, æA review of Abrasive Wear of MetalsÆ by saying:à it is difficult to give guidelines for selecting materials for abrasive wear resistance. Each application is a different one, and a design engineer has to take into account various other factors such as impact, fatigue and corrosion which are often coupled with abrasive wear. The same applies to ceramics.CITATION:Stead, R, 2013. Applications of ceramic wear materials in the gold industry, in Proceedings World Gold 2013, pp 325-330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By A Scott, I Onederra

A great deal of technical and research effort has been applied to the development of models to predict fragmentation from rock blasting. A number of quite useful empirical or engineering models are currently available to blasting engineers and consultants, while more sophisticated approaches using mechanistic and numerical descriptions of rock breakage continue to be developed and applied by researchers and explosives companies.The fragmentation resulting from any blast will be heavily dependent on the properties of the rock mass being blasted; however, most empirical models rely on ‘rock factors’ generated from simple rock mass properties to describe the influence of the rock on the blasting outcome. In contrast, mechanistic models need explicit rock mass properties that require sophisticated laboratory measurements and detailed structural data if realistic outcomes are to be generated. The fragmentation modeller is caught between excessively simple rock mass descriptions for the empirical models and excessively complex data requirements for the mechanistic models.This paper briefly reviews the basis of a range of fragmentation models and the rock mass properties on which they rely. Shortcomings in the way that the mining industry tends to characterise the blasting properties of rock are discussed and some practical approaches are described to quantify these properties in both operating and greenfield mining environments. Case studies are presented where specific additional breakage properties and modelling features have been needed to generate a useful description of the fragmentation achieved.CITATION:Scott, A and Onederra, I, 2015. Characterising rock mass properties for fragmentation modelling, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 149–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Kavanagh M. E, Henley R. W

The Meekatharra mining district lies in the northern pan of the Murchison Province of the Archaean Ynlgam block of Western Australia. Since dis- covery of the Paddy's Flat belt in the district in 1897 total gold production has been 67 tonnes and a further 33 tonnes in resources have been defined by drilling. The Paddy's Flat gold deposits occur within the Gabanintha Formation, a basal formation of the Murchison greenstone sequence containing komatiitic basalts, ultramafics and minor banded iron formations. The regional control on the distribution of deposits is an anastomosing shear belt which extends over 350 km and incorporates the Mt Magnet, Reedys and Meekatharra deposits. The following gold deposit styles may be recognized based on lithological association and alteration: Albite porphyry hosted, Carbonate-fuchsite- quartz alteration hosted deposits, Banded Iron Formation hosted sulphide replacement gold deposits and quartz vein deposits. With the exception of the banded iron formation hosted deposits, the Paddy's Flat alteration zone shows strong similarities to the alteration styles at Kerr-Addison (Ontario).

Jan 1, 1991

By F Djukic, T Fisher, G Irving

Questionnaires were sent to 12 underground metalliferous mines in Queensland to enquire how these mines control diesel emissions from mobile diesel engines used underground. Where responses or controls were absent, discussion has been provided. A significant finding concerns secondary ventilation design rates. Some mines were designing ventilation rates to meet the superseded Mines Regulation Act of 1989 which required 0.04 m3/s/kW. The current Queensland Mining and Quarrying Safety and Health Regulation (2001) is risk based. In line with other jurisdictions, including New South Wales (NSW) and most Provinces in Canada, a minimum ventilation rate of 0.06 m3/s/kW is acceptable. However, this design ventilation rate will vary in practice depending on the diesel engines and controls. Dedicated ventilation engineers and technicians should be appointed to evaluate the effectiveness of the ventilation system. Personal exposure monitoring is required to confirm that exposure standards are not being exceeded. The primary control practice should be to reduce the emission at source. This can be ensured by purchasing low emission (Tier 2, Tier 3) equipment. In addition, the use of ultra low sulfur fuel (et al, 2002). Diesel fuel with a low aromatic content such as Eromanga diesel fuel will also mean employees are exposed to lower levels of poly-cyclic aromatic hydrocarbons. These controls should be carried out in parallel with good maintenance practices. Preventative maintenance should be programmed and emissions be routinely tested, including both gaseous and particulate pollutants and compared against defined criteria. According to McGinn, 2002, there are a number of fundamental tools necessary to carry out preventative maintenance. These are outlined in maintenance guidelines and best practices for diesel engines in underground mining produced for the Diesel Emissions Evaluation Program (DEEP). An effective diesel emission management system needs to be fully integrated within the Safety and Health Management System. These requirements are further discussed in this paper.

Jan 1, 2007

By D Smith, A Ramdhani, J Francke

Ground penetrating radar (GPR), a well-established geophysical technique generally used for shallow civil engineering applications, has, in the last decade, found increasing acceptance as a complementary tool in mineral resource evaluations. As new sites are trialled with the method, a greater understanding is being garnered regarding the most suitable environments for long-range radar. Although successful projects have been conducted worldwide for mineral sands, iron ore and alluvial projects – tropical weathering environments have produced some of the most impressive results. Specifically, tropical nickel laterites have shown to be, with some notable exceptions, ideal GPR environments.Such high-resolution remote sensing has particular relevance to bulk commodities or those which possess significant rheological variation within geological units, and has led to some innovative downstream uses within exploration, project development and the larger mining industry. In this paper, we examine the application of long-range GPR in Indonesian nickel laterite deposits in general, to highlight some of these novel applications with particular reference to resource modelling, mine geology and operational economic implications.CITATION:Francke, J, Smith, D and Ramdhani, A, 2014. Ground penetrating radar to enhance the exploration-to-mining value chain, in Proceedings Ninth International Mining Geology Conference 2014 , pp 175–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By P M. Ashley, M T. Costelloe

The Mary Kathleen tailings storage facility (TSF) contains 7.1 Mt of uranium mill tailings. This waste repository was rehabilitated in the mid-1980s using a multibarrier dry cover. At the time of mine closure, it was predicted that acid mine drainage (AMD) generation would not eventuate and that uranium, heavy metals and radionuclides would be adsorbed within the tailings and not seep from the TSF into the environment. This study reports on the environmental status of the TSF. Gamma-ray measurements indicate an intact dry cover of the waste repository. However, seepage (~0.5 L s-1) of acid (pH 5.71), saline (0.31 per cent), high conductivity (8.8 mS cm-1), slightly oxygenated (DO 2.6 mg L-1), radioactive waters occurs from the toe of the tailings dam into the former evaporation ponds and local drainage system. Seepage waters are calcium-magnesium-sulfate rich with elevated Fe, Mn, Ni, U and Zn values. Oxygenation of tailings seepages causes the precipitation of Fe and coprecipitation and adsorption of other metals (Pb, U, Y), metalloids (As), rare earth elements (Ce, La) and radionuclides (U-235, U-238, Th-227). In contrast, Ba, Ni, Sr, Mn, P, S, Ca, Mg, Na and K as well as Ra nuclides (Ra-226 and Ra-228) remain in solution until pH neutralisation and evaporation lead to their precipitation in efflorescences and sulfate-rich evaporative sediments further downstream. Dry capping of Mary Kathleen uranium mill tailings has resulted in physical containment of the wastes. The dry cover shows no signs of erosion and radiation levels are within acceptable limits. However, the flow rate of surface seepage from the TSF occurs at a much higher rate than predicted. Also, the neutralising potential and adsorption capacity of the tailings and underlying aquifer were overestimated at the time of mine closure. AMD has developed mobilising metals, metalloids, rare earth elements, alkalis, radionuclides and sulfate from the waste repository into surface water seepages.

Jan 1, 2003

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By R Stimpson, B Johnson, B Hesse

During a period of twelve months between FY18-19, a series of trials were conducted to compare production drilling accuracy using two different methodologies, and the subsequent impact this had on stope performance (dilution and recovery). Testing was conducted at a series of underground mines in Australia. The drill rig’s existing alignment processes were compared to a new technology system, with the following observations: • The new technology was proven to limit rig alignment error, thereby reducing average blasthole deviation, resulting in an increase in the number of holes drilled within tolerance by up to 160%. • The increased accuracy reduced stope dilution significantly by reducing over-break of subgrade ore, whilst also increasing drilled meters (faster stope-cycle time), reducing the bridged tonnes ratio, and facilitating the capture of previously uneconomical stopes. A cost-benefit analysis extrapolated from each of the trials showed the extent to which the new technology, when applied to production data, reduced average dilution, increased ore recovery as well as general drill and blast productivity. In one such trial, the new technology was proven to have reduced average dilution by net 45.4%, which if applied to a full year’s production data, would result in AUD8.2M additional ore recovered, with AUD4.5M less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 to AUD106. This improvement was maintained over the following 12 months – reducing average dilution from 22% in FY17 to 12.1% in FY19.

Mar 15, 2021

By P A. Tilyard

There have been enormous changes in mineral processing in the past four decades. For example grinding mill power has increased by an order of magnitude, regrinding is done to -10 microns and flotation machines are 100 times bigger. Operating staff have unprecedented opportunities for online monitoring and performance control of mineral processing plants. Sophisticated instruments can provide a plethora of data characterising the mineralogy and surfaces of particles. Digital computers allow complex calculations on huge amounts of data including modelling and simulation of machine and plant performance. However, all these changes have not necessarily lead to better metallurgical results. An analogy can be drawn with the thoroughbred racing industry in Australia. Significant advances in scientific knowledge in animal genetics, physiology, biomechanics and nutrition applied to the business have resulted in only a two per cent reduction in winning times for the Melbourne Cup and Caulfield Cup since the 1920s. A critical look at some mineral processing metrics suggests similar failures to improve performance despite putting in more resources. In fact certain parameters such as operating times and plant start-up performance are considered to have remained static or even deteriorated. There has been an emphasis on 'process' at the expense of 'outcomes'. The industry's strength has been in finding technical (or 'hardware') solutions while its weakness has been at the people end of the business in maximising and consolidating the gains from the technologies. Some trends in plant design over these years have exacerbated the apparent deskilling of operating and technical staff. Despite unparalleled options for communications, some staff are embarrassingly uninformed about technical developments in their fields. The 'boom and bust' cycles of the industry, together with trends in tertiary education and the effects of fly-in, fly-out (FIFO) operations, raise serious questions about the sustainability of human capital in the mineral processing sector. This paper by two experienced mineral processing engineers, with contributions from other senior practitioners, reviews these trends. While there may be an element of 'the older we are, the better we were', it is an attempt to identify the issues and propose solutions.

Jan 1, 2009

By M Astorga, J Jackson, J Gaunt

The Ban Houayxai mine (BHX) is a relatively low-grade, low-cost, open pit gold-silver deposit in Laos operated by Phu Bia Mining, a subsidiary of PanAust. The ore production rate at BHX is 4.5 Mt/a, with direct tipping to a semi-autogenous grinding/ball mill circuit with a carbon-in-leach process plant. Approximately 100 000 oz of gold is produced per annum.The operation is located in mountainous terrain with minimal run-of-mine stockpiling. This results in limited capacity for blending from stockpile, with the mill instead reliant upon direct feed ex-pit. Since commissioning in 2012, the plant has seen significant variation in milling rates due to variability in the feed properties of the oxide, transition and primary ores. As part of an ongoing continuous improvement program, an integrated approach was initiated, focusing on maintaining and enhancing production in the future as the proportion of harder primary ore increases. This will specifically focus on direct blending from the loading face using the ore properties and blast fragmentation to maintain mill throughput.This approach was based on the concept of physical assets management, commencing with improving information and knowledge of the condition of the orebody through modelling the characteristics, variability and performance of the feed for processes relevant to throughput. These models are used to support both mine and process plant production planning.The key ore feed characteristics and parameters modelled for the life-of-mine are blastability index, powder factor, crushability or impact resistance and grindability. These predictive spatial models were based on the data from diamond drill holes used in resource definition and geotechnical drilling programs by integrating geotechnical, geological, geochemical and metallurgical data.At the early stages of implementation, the models are being utilised for ore blending decisions to provide guidance and support for budgeting, long-term mine planning, blast design for mill feed and providing the mill with an expectation of performance.CITATION:Jackson, J, Gaunt, J and Astorga, M, 2014. Predicting mill ore feed variability using integrated geotechnical/geometallurgical models, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 165–176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By G A. Blengini, S V. èolar

The minerals industry is faced with choices beginning in the exploration phase and extending over the life cycle of the mine. Firms examine the technical feasibility of alternative actions and typically rank them based on economic performance. Increasingly firms also consider alternativesÆ contribution to sustainable development. There are many visions of what a sustainable future should look like and much debate about what should be sustained. Sustainability is a process, a series of incremental actions, and each alternative course of action has the potential to further progress toward one or more sustainability goal. However, because it is not possible to sustain everything everywhere simultaneously, trade-offs and choices inevitably have to be made.Sustainable decision making before investment (ex ante decisions) should incorporate a broad suite of quantitative and qualitative information. One approach is to utilise an integrated sustainability assessment (ISA) framework that supplements traditional technical and financial tools with other tools such as objectives hierarchies (OH) and life cycle assessments (LCA). OH is a problem framing method that captures stakeholder and decision maker interests, objectives and values. LCA addresses material and energy flows, and environmental impacts. The outputs of these tools can be combined with additional qualitative measures and analysed using multi-criteria decision analysis (MCDA). MCDA models facilitate comparison of different alternatives on the basis of a set of criteria and indicators. Some can incorporate information on risk attitudes and preferences ( multi-attitribute value theory models) and others uncertainty about outcomes (multi-attribute utility models). Studies have been published describing and comparing tools for minerals sector decision analysis. Our paper extends this literature, discussing how a combined OH-LCA-MCDA can support ex ante sustainability assessment by incorporating preferences, risk attitudes, and monetised or non-monetised social and economic variables, in a manner that captures their inherent complexity. We also discuss how such a combined model would support trade-off analysis.

Jan 1, 2009

By S Bhandari

This paper is a step in the direction of developing a computer model of the near source dispersal of suspended particulate matter (SPM) in planetary boundary layer (PBL). Since Surface Mine blasting is done during daytime, study of daytime dispersion in convective boundary layer (CBL) is relevant to the mining engineers. The scope of this paper covers dispersal after the blast in any type of PBL ie stable, convective and neutral but only under weak wind condition. Mathematical analysis of the dispersion of vertical dust column has been carried out during weak wind conditions in a tropical meteorological environment. It is noted that dust concentration reaches its maximum value some distance away from the point of blast, immediately after the blast (t*=1) and thereafter rapidly decreases. After a short interval from the time of blast at t*=11 the dust concentration shows linear decrease in concentration with distance. Dust concentration also rapidly drops during the interval t*=1 to t*=11, thereafter, rate of drop is nearly the same at any distance from the point of blast.

Jan 1, 2001

By J L. Kerr, J Beyer-Robson, S Vink

Driven by an increasing need for water conservation, coal mine operators in the upper Isaac River catchment have placed significant emphasis upon the reuse of water. This initiative led to an overall increase in the salinity of mine waters. The ionic composition of this water differs from local stream water in that concentrations of sulfate are higher than average stream concentrations by ten per cent, while concentrations of bicarbonate and calcium are lower. When this water is discharged into ephemeral streams in semi-arid environments there is potential for this increased salinity and altered ionic composition to impact upon the ecosystem processes mediated by micro-organisms in river sediments.We have measured nitrification, denitrification and methanogenesis rates in a series of lab experiments using sediments from Isaac River catchment streams and found that salinity affects these processes in different ways and to different degrees. Process rates were shown to differ seasonally between samples taken from the same location and habitat type and also between different habitat types at the same time and location. Both aerobic and anaerobic process rates were higher in surface sediments and it is likely that this activity is associated with surface biofilms. Furthermore, we have shown that the ecosystem processes we have measured are limited by the availability of carbon in the sediments.The management implications of these findings for mine releases into ephemeral streams will be discussed.CITATION:Kerr, J L, Vink, S and Beyer-Robson, J, 2013. The effects of increased salinity on microbially mediated ecosystem processes in ephemeral streams, in Proceedings Water in Mining 2013 , pp 121-134 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By G Tsatouhas, R Newell, K Y. Wong

A sulfide ion selective electrode was used to control sulfidiser addition in the flotation testing of a synthetic and a naturally occurring ore containing malachite in order to compare the behaviour of sodium sulfide and calcium polysulfide. Both slug and controlled potential sulfidisation methods of addition were used. Under defined optimum CPS conditions, calcium polysulfide was a more effective sulfidising agent than sodium sulfide on the basis of both capital and operating costs. Surface and solution studies were used to compare the mechanism of each sulfidiser. For calcium polysulfide, XPS showed that polysulfide ions are adsorbed, whereas for sodium sulfide it is the hydrosulfide ions that are adsorbed on the mineral surface. For calcium polysulfide, the CuSx layer was believed to form on the malachite surface, which promoted the flotation of the malachite, by xanthate. Studies of surface morphology of the sulfidised malachite showed that a fairly uniform sulfidised layer is formed with both reagents. The use of sodium sulfide resulted in a thinner initial sulfidised layer compared to polysulfide at equivalent initial sulfur concentration.

Jan 1, 2005