Search Documents

Edwin H. MessiteR, New Pork City (communication to the Secretary*):—Under the heading " Flues," Mr. Edwards refers to the Bee-hive construction, a cross-section of which is shown in Fig. 4 of his paper. A flue similar to this was designed by me about six years ago,' in which the walls though much thinner than those described by Mr. Edwards gave entire satisfaction. These walls, from 2.25 in. thick throughout in the smaller flues, to 3.25 in. in the larger, were built by plastering the cement mortar on expanded-metal lath without the use of any forms, or cribs, whatever, at a cost of labor generally less then $1 per sq. yd. of wall. Of course, where plasterers cannot be obtained on reasonable terms, the cement can be molded between wooden forms, though it is difficult to see how it can be done with an interior core only as stated by Mr. Edwards. In regard to the effect of sulphur dioxide and furnace-gases on the cement, I have found that, in certain cases, this is a matter which must be given very careful attention. Where there is sufficient heat to prevent the existence of condensed moisture inside of the flue, there is apparently no action whatever on the cement, but if the concrete is wet, it is rapidly affected by these gases. At points near the furnaces there is generally sufficient heat not only to prevent internal condensation of the aqueous vapor always present in the gases, but also to evaporate water from rain or snow falling on the outside of the flue. Further along, a point is reached where rain-water will percolate through minute cracks caused by expansion and contraction, and reach the interior, even though internal condensation does not occur there in dry weather. From this point to the end of the flue the roof must be coated on the outside with asphalt paint or other impervious material. In very long flues a point may be reached where moisture will condense on the inside of the malls in cold weather. From this point to

Jan 1, 1905

By S. Grinsfelder

Although wildcatting was hampered by the general overproduction and low price of crude, several developments, worthy of note in the history of the petroleum industry in the Rocky Mountain region, were made in 1927. This district records production from six new fields, two of these having been heretofore productive of gas. Deeper pay horizons were found in two other oil fields. In order to facilitate transportation from fields, six new oil pipe lines were completed or in the course of construction at the end of the year, and one line is proposed for 1928. Four gas lines were completed, one was under construction, and one was proposed for 1928. The total production in 1927 in the Rocky Mountain district was 29,591,379 bbl.,' a decrease of 7,771,991 bbl., or 21 per cent., fro111 the previous year. This was occasioned by natural decline and the general curtailment of production and drilling. A review of the development by states follows. Colorado Production from horizons in the Morrison and Sundance at Craig and at Ilrs Dome, and the bringing in of the deepest producing well in the Rocky Mountain district on North McCalluin anticline (Waltlrn) in Jackson County are the outstanding developments for the year in Colorado. In March the Midwest Refining Co.'s Parkinson 21 SD, SW SE, Sec. 22 T p. 4 N R 92 W, Iles Domr, Moffat County Colorado, found gas in sands in the Morrison estimated at 15,000,000 cu. ft., and at 3242 ft. an oil sand was encountered in the Sundance. Initial production from this horizon was 2575 bbl. in this well. This structure previously was only productive of water in the sands of the Dakota group but has been producing shale oil from horizons in the Benton. The second well completed by the Midwest Refining Co., No. 18 SD in Sec. 23 was also productive of gas in the Morrison and made an initial of 300 bbl. from sands in the Sundance. By the end of the year three other wells wrrc nearing the completion stage but none of them indicate that they will be as big producers as the discovery. To date the productive area has

Jan 1, 1928

By Immo H. Redeker

North Carolina is the leading state in the US in lithium mineral production. Spodumene is mined in open pits and concentrated by flotation by the two companies, Lithium Corp. of America and Foote Mineral Co. North Carolina State University has a mineral research laboratoy in Asheville, N. C., with trained personnel, batch and pilot plant facilities to assist in the state's mineral development. The NCSU Minerals Research Laboratory assisted both lithium-producing companies with spodumene concentration problems and has lately worked closely with Lithium Corp. of America to develop the best flowsheet for spodumene and byproduct recovery. The concentration of North Carolina spodumene and byproducts from pegmatites is presented and illustrated with figures.

Jan 1, 1980

By R. Maddi, I. R. Kramer

C. S. Roberts (Dow Chemical Co., Midland, Mich.)— In this study we have seen another example of how modern electronic instrumentation can be of great value to metallurgical research. The authors have shown much ingenuity in their experimental work. However, I wish to point out that anelasticity theory tells us that we must be cautious when we use pulse methods for measurements which are to be correlated with knowledge of static stress-strain behavior. The basic stress calibrations used by the authors depend on the use of static moduli combined with the pulsed strains. No recognition of a possible modulus defect has been indicated. The general agreement of critical resolved shear stresses may indicate that a

Jan 1, 1953

By H. L. Sauder, J. L. Newman, C. Waddell

An instrument capable of measuring subsurface flow rates is described. The instrument is self-contained and may be run on piano wire line. It detects flow by means of an impeller suspended between two torsion wires. The force of the well fluid striking the impeller causes the impeller to rotate, exerting a torsional force to the wires. This force is determined by recording the angle of rotation of the impeller on film using a battery-driven, clock-controlled camera. The impeller is sensitive to flow in either direction and the same instrument can be used to measure injection as well as production rates. Changes in direction of flow, such as might be caused by thief zones, are measurable and are indicated by a reversal of the direction of rotation of the impeller. Adjustment of the sensitivity of the instrument to measure a wide range of flow rates is accomplished by the use of different size torsion wires. An umbrella-type fluid trap, which contacts the casing or wellbore, diverts the flow through the flow tube. The fluid trap remains closed while rurrning in the hole and can be opened at any point in the well. The instrument with the trap closed is 1 3/4 in. OD and may be run through 2 in. tubing. Successful flow profiles have been made on wells with flow rates ranging from 60 BID to 4,000 B/D at surface pressure up to 4,500 psi. The instrument is designed for high-pressure and high-temperature operations. INTRODUCTION The need for an instrument that will measure flow rates in a wellbore is as old as reservoir engineering itself. A number of such devices have been designed within the past few years. Some of these have been described in the literature1,2,3,4,5,6 One of these devices1. a hot-wire anemometer type, made many successful jobs in dry gas producing areas. Difficulty was encountered when this flowmeter was used in wells producing liquids and development work was initiated to overcome this difficulty. The present flowmeter is the result of this work and provides an instrument with a wider range of application in the industry. Consider- able development work has been done on the tool involving many changes in the mechanics of recording the flow readings, however, the basic principle of flow detection has remained the same since its inception. PRINCIPLE OF OPERATION The basic principle of operation of the flowmeter is the utilization of a portion of the kinetic energy of flowing well fluid to impart a rotational force to an impeller suspended between two torsion wires. This impeller, Fig. 1, is a screw-type propeller with the blades having a pitch angle of 40. As the well fluid passes through the instrument it strikes the impeller. The resulting force rotates the impeller and twist\ the torsion wires to a balance point at which the torque imparted to the wires balances the force required for the impeller to deflect the well fluid. The impeller is symmetrical and a change in direction of the flow results in a reversal of the direction in which the impeller is deflected. Thus the direction of the flow as well as its velocity is indicated. A dial is attached to the impeller by means of a hollow tube through which the upper torsion wire extends. The angular position of the impeller is recorded by photographing the dial at frequent intervals. In any given set of torsion wires the modulus of shear and polar moment of inertia remain constant and the deflection varies directly with the applied torque. The deflection imparted to the torsion wires also varies as the square of the fluid velocity. Further, the velocities represented by any two given deflections hear the following relationships: and Where V = velocity of flow stream and O ;= deflection. This is the basic relationship which is used to calculate the relative velocities represented by a given set of deflections where the velocity represented by any one of the deflection readings is a known quantity. For a given torque, the deflection of the torsion wire varies inversely as the fourth power of the wire diameter. Wire sizes ranging from ,005 in. in diameter to .022 in. in diameter can be used. The range of

Jan 1, 1957

By C. J. Delisio

The basic concept of tunnel boring has not changed since the late 1800's. R. Stanley of Great Britain obtained a Canadian patent as early as December 1891. Mr. Stanley's machine was a device that consisted of a rotating wheel equipped with drag-type teeth; it had a means of thrusting the cutterhead against the face or heading; it had a means of clamping or gripping the machine in its bore; it had a means of collecting and depositing the cuttings into a screw-type conveyor located near the invert of the tunnel. It even had a means of varying the speed of the forward motion of the machine to suit different hardnesses of rock encountered. This description essentially fits the latest tunnel-boring machines being built today. In short, there has been no significant advance in the basic concept in 70 to 80 years. It may well be that no significant change can be expected for some time into the future. Today's machines, while still basic in concept, offer many advances aimed at faster tunneling. Among these are 1 ) improved cutters, 2) guidance and steering devices, 3) dust-control devices, and 4) mechanisms to aid in installing tunnel supports. CUTTERS The most important part of a hard-rock tunnel borer is the cutter. If the cutter can cut the rock, it is a boring machine. If the cutter cannot cut the rock, no other part of the machine can. When Jarva, Inc. decided to build a machine, the first problem was to find a good cutter. In our search, we looked at most of the cutters on the market. We selected Reed Drilling Tools' cutter because the design of their cutter was aimed at hard-rock tunneling. We feel that they build the best cutter available and provide the best possible service to their customers. As tunnel-boring machine design advanced, the transition from drag bits to roller bits was natural because harder formations required a roller bit, and it is the goal of all mole users to bore harder formations. Roller bits

Jan 1, 1970

By W. E. Newell

The basic principles and assumptions involved in D. L. White's solution5 for ultrasonic wave amplification in piezoelectric semiconductors are summarized. If the gain per unit length is maximized at each frequency without regard to the drift-field power density, the gain increases linearly with frequency. Therefore it would seem that very high gain is possible for frequencies in the hundreds of megacycles. However, with present materials the resulting drift-field power density is so large that cooling would be a major problem. For this reason it is more realistic to judge the capabilities of an ultrasonic amplifier in terms of the gain that is possible with a specified power density. In this case the gain at high frequencies does not increase but decreases more rapidly than l/f. The calculation of the gain us frequency at a fixed power level involves the repeated solution of a cubic equation and is therefore tedious. For the purpose of comparing different materials, sufficient accuracy can be obtained from an approximate solution which may easily be plotted as three straight lines on logarithmic graph paper. This method is used to compare the Performances of CdS, CdSe, ZnO, and GaAs. At a power density of 10 watts per cu cm, the first three give maximum gains of 60 to 80 db per cm in the vicinity of 60 megacycles. At the same power density, GaAs has a maximum gain of about 7 db per cm near 150 megacycles. Although an increase in mobility usually increases the gain for a specified power density, it is shown that there is an optimum mobility above which the gain decreases. An approximate expression for the optimum mobility is established. It is well-known that the interaction between charged particles and an electromagnetic wave can be used to amplify the electromagnetic wave. In the conventional traveling-wave tube, electrons in a vacuum are caused to move at a velocity slightly greater than the wave velocity, thereby coupling energy into the wave.' In principle, the same effect would be evident in a solid except that repeated collisions prevent the electrons from attaining a velocity greater than that of an electromagnetic wave. However, the drift velocity of electrons can be made to exceed the velocity of an acoustic wave in a solid. In 1956, weinreich2 noted that the deformation potential provided one means of coupling energy from drifting electrons into an acoustic wave, but the effect was too small to be of any practical importance. It was not until 1961 that White and Hutson demonstrated that the piezoelectric effect provided a strong enough coupling to give appreciable amplification of an ultrasonic wave and awakened wide interest in electron-phonon interactions. Qualitatively the effect may be described as follows. An acoustic wave propagating through a piezoelectric material is accompanied by an electric-field wave. If the vibrations are properly oriented with respect to the crystal axes of a piezoelectric semiconductor, the local electric fields are axially directed and cause bunching of the charged carriers. If the drift velocity of these carriers is less than the velocity of sound, they tend to be dragged along by the acoustic wave. This electroacoustic effect results in a net potential appearing across the material and in attenuation of the acoustic wave. On the other hand, if the drift velocity exceeds the velocity of sound, energy is coupled from the carriers to the acoustic wave and amplification results. Related effects which are being investigated include ultrasonic amplification in semimetals6-' and semi-conductor, and current saturation in piezoelectric semiconductors.'4-17 There are various problems which hinder the immediate application of ultrasonic amplification in a practical device. First, there are the traditional problems encountered in the design of acoustic delay lines: attenuation in the electromechanical transducers, reflected waves (which can lead to self-oscillation in an amplifying device), mechanical tolerances necessary to maintain phase coherence, and so forth. Second, there is the problem of selecting the best material from among the various piezoelectric semiconductors as they become available in single-crystal form with a wide choice of characteristics. This paper deals with the second problem and shows that the most realistic way of comparing materials is in terms of the gain which can be obtained without exceeding a

Jan 1, 1964

In answer to inquiries from members, Mr. Sheafer said that the culm-banks of which his paper gave the shipments were of about the average quality of the banks in the Mahanoy region of the Schuylkill field,.made prior to 1881 or 1882, when the practice of preparing buckwheat coal was introduced; but that in a very old hank, made about 1849, no coal above pea-size had been found. Apparently it was then the practice to ship everything. In reply to an inquiry concerning the utilization of the fine coaldust, Mr. Sheafer said that it was not utilized in connection with the washing described in his paper, but was carried away in the water as waste; that during Mr. Corbin's presidency the Reading Company built at Mahanoy City an extensive plant for making artificial fuel, but difficulty was encountered, due to the circumstance that the small coal from different collieries varied in its combustible quality and also in the amount of pitch required to be mixed with it, and he believed they concluded that from some varieties of the coal-dust a very good fuel could be made, but at a cost entirely too great for successful competition with cheap coal. Of course, the anthracite dust was not so well suited to this manufacture as bituminous slack. R. W. Raymond, New York City : I believe that was the practical outcome of the enterprise of a member of the Institute, Mr. E. F. Loiseau, now deceased. It was found, I think, as an additional drawback, that the manufacture of artificial compressed fuel from anthracite dust could not be successfully practiced with material so impure as that of the culm-banks. Consequently, the manufacture could be based on that source of supply only when accompanied with a preparatory washing. The most favorable location for it would be at large yards where the waste from the handling of coal, which is comparatively pure material, could be thus treated. I believe the manufacture of compressed fuel from bituminous coal was at one time a profitable business in Nova Scotia, but was destroyed by the indirect effect of the general introduction of watergas for illuminating purposes. The result of that change on the

Jan 1, 1895

Papers in Classes A-Metal Mining, B-Milling and Concentration, H-Indus¬trial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every other month. Papers in Classes C-Iron and Steel Division, D¬-Nonferrous Metallurgy and E-Institute of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. Papers in Class G-Pe¬troleum Division are distributed in PE¬TROLEUM TECHNOLOGY, which is issued every other month. TECHNICAL PUBLICA¬TIONS in Classes F-Coal Division, J¬-Mineral Industry Education Division, K¬-Mining Administration, and 1-Geophysics, are issued as separate pamphlets. Contributions are papers that when printed or mimeographed are available but only on request.

Jan 1, 1943

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By R. E. Crater

Brown, Gaudin, and Loeb in their study of intergranular comminution by heating attempt to find one explanation for all types of rock in terms of the properties of the phases present. The only necessary condition for intergranular cracking by heating is the setting up of high stresses at the grain boundaries. Such stresses may be set up in multiphase isotropic mixtures if the thermal expansions of the phases are different, in non-cubic single phases because of the anisotropy of thermal expansion in the various crystallographic directions, and in materials containing quartz because of the a-ß transformation at 575°C. In addition, for intergranular comminution by heating, the cooling and not the heating is most important.

Jan 3, 1959

By P. Somasundaran Discussion by Knut L. Sandvik

Knut L. Sandvik (Mining Engineer, Mineral Dressing Laboratory, Technical University of Norway, Trond-heim, Norway) — The discovery that adsorption at solid-liquid interfaces is influenced by adsorption at other interfaces may prove very fruitful in the further development of flotation theory. Having reached the same conclusions as P. Somasundaran in some experiments with amine hydrochlorides, I would like to offer more direct evidence of the interfacial adsorption mechanism based on surface tension measurements and adsorption studies.' This evidence was derived from flotation tests carried out in a Hallimond tube at neutral pH and 60°C. The amount of amine solution and quartz surface were chosen to insure measurable concentration changes during flotation due to adsorption. Adsorption data for

Jan 1, 1969

By AIME AIME

ONE unique distinction can be claimed by the new Chairman of the Coal Division, C. E. Lawall: he is the only A.I.M.E. member also a university president, though several engineering colleges are headed by Institute members. Only last year he was promoted from director of the school of mines to president of West Virginia University, following a term as acting head of that institution of over 3000 students. He was born in Catasauqua, in eastern Pennsylvania, on Nov. 21, 1891, and went to Lehigh, receiving an E.M. in 1914, and an M.S. seven years later. His engineering career began in the Pittsburgh Testing Laboratories. After three years there he came to Palmerton for

Jan 1, 1940

By D. R. Mitchell

FOR the second consecutive year, attendance at the Coal Division sessions far exceeded exoectations. Those in charge were continually faced with problems of finding seats and space for attending members. 115 seats were set - II~ for the annual luncheon meeting of the Division and approximately 175 members showed un. Since the hotel management would not serve more than the 115 it meant that 60 members were forced to eat elsewhere. This created hard feelings with some members. How- ever, officials of the Division were not able to obtain in advance any indication of this overflow crowd, but are suggesting to the New York Office that some means other than ticket sales be adopted to obtain an estimate of Division luncheon and dinner attendance. Members could be circularized prior to he meeting or they could be checked when registering as to the events they expect to attend. Under the inspiring leadership of Cadwallader Evans, Jr., Chairman, the Coal Division had a phenomenal growth during the year. Reporting at the luncheon meeting, Newel1 Alford stated that approximately 190 new members had been obtained. A few more years of continuing increase at this rate will make the Coal Division one of the largest Divisions in the Institute.

Jan 1, 1944

By AIME AIME

IN times of stress nations pick strong men to lead them. Similarly the Coal Division selected forceful Larry A. Shipman, fuel engineer for the Southern Coal and Coke Co., Knoxville, Tenn.. to lead it through the year 1945. He was born in Indianapolis May 13, 1891. Following graduation from a technical high school in that city Larry began his fuel career approximately 35 years ago attached to one end of a scoop shovel, firing locomotives for the Pennsylvania Railroad. At the end of two years he transferred to the New York Central Lines and held these jobs successively: locomotive fireman, engineer, fireman instructor, supervisor of instructors, and fuel engineer.

Jan 1, 1945

W. M. CORSE, Mansfield, .Ohio.-We have sometimes seen in indi-vidual tests ultimate tensile strengths ass high as 55,000 lb. per. sq. in. being attained under electric furnace practice. These results, of course, average much lower than that, but with better methods of melting, can we hope to get the strength up to somewhere near the figure attained by these individual tests? C. P. KARR.--Yes, because with the electric furnace you can lessen the oxidation by means of the impurities always found in the melting. But one of the most important things in making 88-10-2 bronze of this class is to use a core-sand mold with a very open grain, so that the

Jan 12, 1919

By Frank Julian

After the solution of an iron ore, or metallic iron, in an acid, for the determination of phosphorus, it is necessary to evaporate the solution to dryness and to heat the residue to effect the complete separation of silica. Authorities differ as to the temperature required, some recormmentling not over 100' C., others as high as dull redness. For the purpose of securing some indications as to the degree of heat which may be safely or advantageously employed, I selected a gray pig-iron, a piece of Bessemer steel rail, and a sample of Ludington ore having the following composition; the phosphorus in the pig and steel being determined by Giutl's ferric chloride method:

Jan 1, 1884

George Edward WebbeR, a member of the Institute since 1906, died in San Francisco, May 29,1922. Born in Dixmont, Me., in 1852, he went to California in 1857 where he lived until 1883 and received a thorough training in precious metal mining in the employ of his father and J. B. Haggin. In 1883, he went to the Black Hills, South Dakota, as superintendent of the Father DeSmit mine; later the Deadwood Terra also came under his management. These mines are now part of the Homestake Mining Co. In 1889, the Rothchilds asked Hamilton Smith to recommend an engineer to take the place of the late Henning Jennings, who had resigned from the El Calloo Mining Co., of El Calloo, Venezuela, in order that he might proceed to South Africa. Mr. Webber accepted the position, remaining there until 1893 when he returned to the United States on his way to Johannesburg, South Africa, where he had been appointed manager of the Crown Reef Mining Co., Ltd. Early in 1896, he became general manager of the Rand Mines, Ltd., and served in this capacity until 1911. During the latter part of this period, Mr. Webber was active in the greater amalgamations of H. Eckstein & Co., and it was largely on his advice that H. Eckstein & Co. carried out the negotiations preceding the formation of the Crown Mines, Ltd. On his retirement from South Africa, he returned to live in Ross Valley, near San Francisco, Cal. The Rand Mines, Ltd., of which Mr. Webber was general manager, was the largest company controlled by Wernher Beit, the leading London house interested in South Africa mining, whose local agents in Johannesburg were H. Eckstein & Co. This firm is now known as the Central Mining & Investment Corpn., and after the departure of Henning Jennings, Mr. Webber was the firm's most valued and confidential advisor and was very highly thought of in mining circles in South Africa. He was a ma of most upright and straightforward high character, plain spoken and sincere; and his recognized high character was one more qualification which aided his great success.

Jan 1, 1923

George Edward WebbeR, a member of the Institute since 1906, died in San Francisco, May 29,1922. Born in Dixmont, Me., in 1852, he went to California in 1857 where he lived until 1883 and received a thorough training in precious metal mining in the employ of his father and J. B. Haggin. In 1883, he went to the Black Hills, South Dakota, as superintendent of the Father DeSmit mine; later the Deadwood Terra also came under his management. These mines are now part of the Homestake Mining Co. In 1889, the Rothchilds asked Hamilton Smith to recommend an engineer to take the place of the late Henning Jennings, who had resigned from the El Calloo Mining Co., of El Calloo, Venezuela, in order that he might proceed to South Africa. Mr. Webber accepted the position, remaining there until 1893 when he returned to the United States on his way to Johannesburg, South Africa, where he had been appointed manager of the Crown Reef Mining Co., Ltd. Early in 1896, he became general manager of the Rand Mines, Ltd., and served in this capacity until 1911. During the latter part of this period, Mr. Webber was active in the greater amalgamations of H. Eckstein & Co., and it was largely on his advice that H. Eckstein & Co. carried out the negotiations preceding the formation of the Crown Mines, Ltd. On his retirement from South Africa, he returned to live in Ross Valley, near San Francisco, Cal. The Rand Mines, Ltd., of which Mr. Webber was general manager, was the largest company controlled by Wernher Beit, the leading London house interested in South Africa mining, whose local agents in Johannesburg were H. Eckstein & Co. This firm is now known as the Central Mining & Investment Corpn., and after the departure of Henning Jennings, Mr. Webber was the firm's most valued and confidential advisor and was very highly thought of in mining circles in South Africa. He was a ma of most upright and straightforward high character, plain spoken and sincere; and his recognized high character was one more qualification which aided his great success.

Jan 1, 1923

By A. C. Fieldner

In November, 1926, the American Engineering Standards Committee (now the American Standards Association) called a meeting of representatives of various professional societies and industrial, educational and governmental organizations to consider what action, if any, should be taken on the classification of North American coals. This meeting was called because a system for the use classification of coal, proposed by George H. Ashley, had been referred to the committee by the Coal Mining Institute of America. This meeting, at Pittsburgh, was well attended and was definitely in favor of taking up the whole question of scientific and use classification of coals, including all the various ranks from lignite to anthracite. The American Society for Testing Materials was recommended as the sponsor organization to take charge of the work and organize the sectional committee according to the rules of the American Standards Association. The American Society for Testing Materials proceeded with the organization of the sectional committee, holding a meeting in Philadelphia, June 10, 1927. Officers were elected, regulations adopted, and general plans for carrying out the work were outlined. The total membership of 28 comprising the sectional committee consists of 8 producers, 2 distributors, 9 consumers and 9 members representing general and scientific interest. From this committee three technical committees of 10 to 12 members each were organized: Scientific Classification, H. J. Rose, chairman; Use Classification, W. H. Fulweiler, chairman; Marketing Practice, F. R. Wadleigh, chairman. The Technical Committee on Scientific Classification was requested to formulate a system of coal classification based on chemical and physical properties of coal and with reference to origin and constitution. The Technical Committee on Use Classification was charged with developing a system of classification, if possible, based primarily on the uses of coal and commercial practice; this system to be correlated with the scientific system as far as possible and desirable. The Technical Commitlee on Marketing Practice was formed to collect and collate information on commercial practice for the benefit of the other two committees. The first meetings of the technical committees were held on Nov. 17, 1927, and the first informal progress reports were submitted to the

Jan 1, 1930