Search Documents

By E. V. Potter, H. C. Lukens

INTRODUCTION IN general, during all electrowinning processes, large volumes of gas are liberated at the cathodes of the electrolytic cells. Most of this gas escapes from the electrolyte, but much of it may be absorbed or entrapped in the metal being plated. In many cases, this is not objectionable, but since it is liberated when the metal is heated, it is a potential source of trouble where the metal has to be heated or melted. Since this gas is principally hydrogen, in escaping from a melt it may cause minor explosions and scattering of the molten metal, while in other cases it has been reported to make the metal rise in the molds when cast. Therefore such metals would be more generally useful if all or most of the gas were removed before they were used. In an earlier investigation' the gas content of electrolytic manganese was determined and methods found for removing most of it without detrimentally affecting the properties of the metal. In this paper results of a similar investigation on electrolytic chromium are presented. APPARATUS The apparatus used in these investigations is essentially the same as that used in the manganese work' and is shown in Fig I. It consists of sample chamber A, vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The pressure in the system is measured by the mercury manometer B. Changes in ' gas volume are measured by volume gauge C which is essentially another mercury manometer in which . the volume of the mercury column is large and can be varied by raising or lowering the well H. In this apparatus the tube had a volume of 100 cc for a 61 cm length. Larger changes in gas volume can be accommodated by auxiliary containers attached to the system at F. The sample is heated by furnace G, the temperature of which is regulated within ± 5°C by an automatic controller. The only change in the apparatus was the sample container which was made smaller because of the chromium metal's containing more gas than the manganese metal and a smaller sample was used. METHOD The measurements were made as follows: The complete system when cold was evacuated and refilled with H2 until all the air was removed. It was then refilled with H2 to the desired pressure, as indicated on manometer B. The temperature was then raised to the desired value and as gas was either liberated from or absorbed by the sample, the height of well H was changed to alter the volume of the system so as to keep the pressure constant. In determining rates of liberation of gas, volume readings were taken at convenient time intervals depending on the rapidity with which the gas was liberated. In determining total volumes, the specimen was held at constant temperature and pressure until

Jan 1, 1948

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By Nicholas J. Grant, H. C. Chang

EMPHASIS on the importance of grain boundary sliding as a mode of deformation at elevated temperatures has been presented elsewhere.' The extent to which boundary sliding occurs under certain creep conditions has been determined for high purity aluminum2,3 and aluminum alloys.' In general, boundary deformation extends quite far into the adjoining grains, resulting in a rather wide band of deformation along the grain boundaries. This has led some investigators to doubt that grain boundary sliding consists of shearing along the boundary surface; it has been contended instead that boundary sliding is a result of concentrated slip in the neighborhood of the deformed grain boundaries."' The purpose of this note is to present evidence that grain boundary sliding takes place by a bulk shear process. gh purity polycrystalline aluminum, wherever and whenever there is grain boundary sliding, boundary migration and concentrated deformation along both sides of the deformed boundary are associated with it. Therefore, it has been rather difficult to obtain unambiguous evidence of boundary sliding. On the other hand, it would be expected in certain alloys of aluminum, when tested under particular conditions. that the severity of the interfering effects of boundary migration and concentrated deformation along the deformed boundary might be reduced. Current research in this laboratory' shows that a 20 pct Zn-A1 solid solution alloy fractures in an intercrystalline manner during creep at 500°F with a small total elongation of not more than about 14 pct, and that it does so with extremely limited grain boundary migration. Accordingly, this alloy was chosen for the present study. The experimental procedure was similar to that used in previous work and has been presented elsewhere.' Two parallel flat surfaces were milled from a round specimen. The gage portion of the specimen was 1 in. x .09 in. x .17 in. The specimens, which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar. The specimens were subjected to creep at 500°F at stresses of 2000 to 5000 psi. The rupture times were from 10 sec to 3 hr. Appreciable boundary sliding occurred in all the tests. A typical example of boundary sliding is shown in Fig. 1. (The tension axis is vertical in the micrographs.) Sliding has taken place along the boundary between grains A and B unaccompanied by important boundary migration. The sharpness of the offset at the triple point can be clearly seen in grain C. As a result of sliding along the boundary between grains A and B, a new boundary surface between grains A and C was created. The offset at the triple point is about 0.07 mm. This boundary sliding is accompanied by the formation of rather sharp kinking bands and, of course, slip on several slip systems in grain C. This type of deformation has been referred to as fold formation' in previous work with high purity aluminum.

Jan 1, 1957

By I. J. Gardescu

The production of petroleum in Rumania in 1932 totaled 52,560,000 bbl., an increase of 6.8 per cent over 1931. The average daily production rose from 123,000 bbl. at the beginning of the year to 173,000 bbl. at the end of the year, the production in the Gura-Ocnitzei field rising from 38,800 to 80,700 bbl. per day. This increase was due to competitive development during which time the percentage of total production of the various operating companies remained practically unchanged. Chief producers were: Concordia, 30.3 per cent; Unirea, 21.6; Romano-Americana, 13.5; Steaua Romana, 8.3. Boldesti, where production of the previous year was practically doubled, would have produced far greater quantities were it not for the fact that both Astra Romana and Romano-Americana curtailed drilling operations. Of the total daily production of 21,800 bbl. a day, the Astra Romana, Steaua Romana and Romana Americana, produced respectively 67, 25 and 8 per cent. The Moreni field showed a sudden drop in production from the preceding year, due primarily to reduced drilling activities. Its production of only 21,000 bbl. a day removes it from first position for the first time in many years. All the other fields showed a decrease in production, except Ochiuri, 3 miles west of Gura-Ocnitzei, and Ceptura, 12 miles east of Boldesti. Drilling1 During the first nine months of 1932, 116 wells were completed, 8 of which were dry holes. The Meotian (lower Pliocene) is the producing horizon in 73, the Dacian (upper Pliocene) in 31, and the Oligocene in 4 of the completed wells. Three of the Oligocene wells were drilled in the Bacau district and one at Grausor, near Campina. In addition, 47 wells were drilling on Oct. 1,1932. Of the total completions and drilling wells, 92 per cent employed rotary for a footage of 98.5 per cent of the total drilled. Power for rotary drilling was furnished to 105 wells by steam, to 38 by electricity, and to one by gasoline.

Jan 1, 1933

By Gilbert Cady

EXTENSIVE Sampling of coal in Illinois during the past 10 or 12 years by the State Geological Survey, in cooperation with various organizations, such as the U. S. Bureau of Mines, the University of Illinois, and the Illinois Cooperative Mining Investigations, has made possible the delineation of two areas of low-sulfur coal in the southern part of Illinois. The sulfur content is less than 1.25 per cent., so that, if otherwise suitable, these coals can be employed for metallurgical uses and for the manufacture of water-gas and retort gas. One of these areas is small and lies in Jack-son County, near Murphysboro, the other is much larger and includes a large part of the famous Franklin County field. A small area of No. 2, or Murphysboro, coal has been worked for many years near the town of Murphysboro, Jackson County, Ill. In two mines, at least, the coal has a sulfur content of less than 1.25 per cent. It is doubtful, however, whether this field will ever be a source of large tonnage as the total area underlain by low-sulfur coal in workable thickness is probably less than 15 sq. mi. (24.14 sq. km.), and a large part of it has already been worked out. The location of the area of low-sulfur coal in the Franklin County field is shown in the accompanying map. The small area underlain by the Murphysboro low-sulfur coal is shown near the town of that name in the central part of Jackson County. The larger area lies in the west side of Franklin County, extending also about 6 mi. (9.65 km.) south into Williamson County, about 4 mi. (6.43 km.) west into northern Jackson and western Perry County, and northward an undetermined distance into Jefferson County. All but the northern limit of the area is fairly well defined by sampling in numerous mines. The inner cross-lined area is underlain by coal having less than 1 per cent. sulfur, the outer boundary surrounding the area Underlain by coal having less than 1.25 per cent, sulfur.

Jan 7, 1919

By Herbert Hoover

THE time has arrived in our national development when we must have- a definite national- program in the development of our great engineering problems. Our rail and water transport, our water supplies for irrigation, our reclamation, the provision of future' fuel resources, the development and distribution of electrical power, all 'cry out for some broad-visioned national guidance. We must create a national engineering sense of provision for the nation as a whole. If we are to develop this national sense of engineering wand its relations to our great human problems, it must receive the advocacy of such institutions as this. We, together with our sister engineering societies, represent the engineers of the United States. It is our duty as citizens to give voice to those critical matters of national policy which our daily contact with this, the fundamentally constructive profession, illuminates to us. Just as our medical associations voice the necessity of -safeguards to national health; as the bar associations of safeguards to our judiciary, so the engineers should exert themselves in our national engineering policies. We have none; but we need some, or the next generation will face a lower instead of a higher standard of living than ours.

Jan 1, 1920

By R. F. Mehl, J. T. Ransom

For many years the Metals Research Laboratory of Carnegie Institute of Technology has been concerned with the statistical nature of the engineering properties of steel from an experimental viewpoint, particularly those properties representing ductility.' In the past three years new work has been directed toward evaluating the statistical nature of the endurance properties. It has been shown that both the fracture curve and the endurance limit in fatigue are markedly statistical in nature. The S-N curve (and the endurance limit) of ferrous materials is often determined with specimens which number as few as ten. The common procedure is to test the first specimen at a stress well above the expected endurance hmit. Each succeeding specimen is then tested at a progressively lower stress, until, after five or six tests, a specimen runs ten million or so cycles without failing. Two or three more specimens are then used to find the highest stress at which failure will not occur; the limiting stress determined in this way is called the endurance limit. It has now been found, however, that the variability in the fracture curve and in the endurance limit in heat-treated alloy forging steels is so great that S-N curves must be drawn on the basis of distribution curves which can be appraised only by statistical methods. Two methods have been adopted in this study: (1) straightforward statistical studies of cycles to fracture of a number of specimens at each of a series of stress levels, and (2) a new abbreviated statistical method, known as "staircase testing."2 The latter corisists in testing a series of specimens, one by one, with the test stress for any given specimen automatically

Jan 1, 1950

By L. W. Fagg

The purpose of this paper is to present in a convenient form data and examples necessary in making dynamometer card analyses; also to outline a procedure of well weighing. Many articles and papers have been written delving into the mathematical considerations relative to the shape and characteristics of dynamometer cards. However. it is recognized that there are too many unknown factors involved in such calculations to assure a workable degree of accuracy. For this reason the accepted procedure is to take dynamometer cards on wells in question rather than try to calculate the load curve. The polished rod dynamometer is now recognized as a necessary tool for measuring loads, torque, and horsepower. It is also used to determine pump action and trouble-shoot for any seemingly abnormal pumping condition. The apparently infinite variety of a = maximum load (height x scale constant) b = minimum load. Range of load is difference between maximum and minimum load speed—taken with stop watch stroke —measured at polished rod c = beginning of down stroke in direction of arrow. (End of up stroke) d = beginning of up stroke. (End of down stroke). Polished Rod Horsepower = (Area of card) x Scale const. x Stroke x Length x spm (Length of card) 33000x 12 1.35 1.35------x5300x 24 x 12 2.53 --------------------------= 2.06 23000x12 Appraximate Peak Torque: Upstroke = (2390) (12) (1) = 28,700 in. Ib Downstroke = (1 860) (12) (.866) = 19,300 in. Ib Counterbalance should be increased to make up stroke and down stroke peak torque equal. FIG. 1 dynamometer cards that can be obtained is one reason for the general lack of usage of the dynamometer as a control instrument rather than a means for making routine measurements of leads and horsepower. When it is considered that the dynamometer card is a record of the resultant of all forces acting on the polished rod at any particular instant during the pumping stroke. the problem is then one of breaking down this resultant into its various components. As a means of a quick review we shall consider the examples shown in Figs. 1 to 9: and Tables I and II and then proceed to the interpretation of variously shaped cards caused by some abnormal operating condition. In Table 11, when we were considering the factors involved in calculating the peak polished rod load, it can be seen that the factors involved greatly oversimplify the problem. Certain assumptions are made which may or may not he even close to the actual field conditions, such as the specific gravity of the fluid generally considered as one; that the crank has constant angular velocity; that the down-hole friction is zero; and that the fluid lift is from the pump. In the following examples we shall see what a variation in fluid weight and friction can do to the general shape and magnitude of the dynamometer card. (Figs. 10 to 22.) MAKING THE WELL STUDY It is obvious that it would be impractical to consider in detail all of these factors each time a well study is made, inasmuch as each well study job could conceivably be extended into a research project rather than serve the practical requirements of finding the answer to a specific problem. For this reason it is important that some objective be established previous to the time the well study is made. Load at TU = 3070 Ib Crank angle when polished rod is at position TU = ? ? = 30° Maximum counterbalance effect at polished rod = 2760 Ib Torque at TU = (Load at TU — Max. counterbalance effect-lbs) sin 0 x Length of Stroke 2 = (3070-2760) .5 x 24 = 1860 in. 15 2 Torque at TD = (Load at TD — Max. counterbalance effect-lbs) sin ? x Length of Stroke 2 = (530 - 2760) sin 330' x 24 = 13,400 in. Ib 2 Note: sin 0 from c to d on UPSTROKE will be positive value. sin 0 from c to d on DOWNSTROKE will be negative value Torque at c and d is zero because 0 is zero. FIG. 2 —APPROXIMATE METHOD FOR CALCUlATlNG TORQUE

Jan 1, 1950

By Philip Kraft

WHEN it came time to write a biography of Philip Kraft, we got out a copy of Bartlett's "Familiar Quotations" and looked through the references to Travel, Traveled, Traveler, and Traveling, feeling sure there would be some reference to Mr. Kraft. Sure enough, we found: "Travel, in the younger sort, is a part of education; in the elder, a part of experience." Had Francis Bacon done his writing three and a half centuries later, Mr. Kraft might well have served as the inspiration for that sentence. New Yorker born, he received his B.S. and E. M. degrees from Columbia. In 1912, then 22 years old, he took off for Germany where he spent two years studying at the Royal School of Mines, Berlin, for his Doctor of Engineering degree. Contrary to the Greeley-Soule precept, Mr. Kraft, on his return from Europe, went north to South Porcupine. Ont., working as geologist and mining engineer for the Dome Mine. From South Porcupine his next stop was Washington, D. C., where, during the years the country was in the first World War, he was engaged in war work.

Jan 1, 1947

By M. J. Marcinkowski, E. N. Hopkins

An investigation has been made of the ß(fcc) — a(hexagonal) transformation which occurs in lanthanum using both electrical resistivity and transmission electron microscopy techniques. It has been shown that the ß phase can be retained below the transformation temperature by rapid quenching but that the sample immediately begins to transform to the a phase. The transformation is observed to nucleate in the vicinity of inclusions. Based on the above observations, a detailed model of the transformation has been advanced which involves the nucleation of an extrinsic stacking fault bounded by a pair of Shockley partial dislocations in the vicinity of some heterogeneity, i.e., an inclusion. The stress field of the resultant dislocation pair acts to nucleate extrinsic faults in adjacent planes and leads quite naturally to the B-a conversion with a minimum of strain energy induced in the crystal. LANTHANUM possesses an fcc structure ß) (8) upon cooling transforms to a hexagonal modification (a) in much the same way as cobalt. The one exception, however, is that the stacking sequence of the closest packed planes in a La is ABAC ABAC, and so forth,1 whereas in cobalt it is ABAB, and so forth, i.e., hep. Mainly on the basis of transmission electron microscopy techniques, there seems to be little doubt that the 0 — a transformation in cobalt involves a dislocation mechanism2 although its exact nature still remains obscure. Although the ß - a transformation in lanthanum is somewhat more complex than that occurring in cobalt, it was thought that its very uniqueness would be helpful in understanding fcc — hexagonal transformations in general. Such a general understanding of these transformations is important since they represent what are perhaps the simplest of the martensitic class of transformations. The experimental techniques used were those of electrical resistivity and transmission electron microscopy. EXPERIMENTAL PROCEDURE The lanthanum used in this investigation was prepared by the calcium reduction of lanthanum fluoride in a tantalum crucible under an argon atmosphere as described by Spedding et al. The residual calcium was removed by vacuum remelting in a tantalum container. Portions of the metal were then analyzed by emission spectroscopy as well as vacuum fusion. The amounts of the various impurities that were found are listed in Table I. A portion of the lanthanum ingot was swaged at room temperature into 0.030-in.-diam rod for the resistivity samples while the remainder was rolled into 0.010-in.-thick sheet for the transmission electron microscopy phase of this investigation. In order to eliminate the plastic deformation induced in the samples during fabrication, they were sealed in evacuated tantalum lined quartz capsules and annealed for 1 hr at 700° C. Specimen resistances were measured using the conventional "four-wire" technique described by MacDonald, 4 employing a type K-3 Universal Potentiometer and a standard 0.001-ohm resistor, both manufactured by Leeds and Northrup Co. By taking into account all of the possible errors in the apparatus, it was felt that the absolute resistivities of the approximately 0.87-in.-long specimens measured are reliable to 3 pct. Resistances from room temperature to 700°C were measured using a vacuum furnace. In order to avoid sample contamination by the thermocouple, chromel-alumel leads were spot-welded into a tantalum shield which in turn was welded to the lanthanum specimen. Resistances below room temperature were obtained by transferring the sample to a helium gas-filled quench tube and slowly dripping liquid nitrogen into a surrounding dewar flask. A steady reduction of temperature to about —190°C was completed in about 23 hr, and the resistances were measured at various temperature intervals. As will be shown shortly, rapid quenching from above about 350°C was sufficient to suppress the B -a transformation initially but subsequent annealing at lower temperatures leads to a partial ß --a conversion. To investigate this aspect of the transformation, the samples were suspended in the hot zone of a helium-filled furnace from which they could be rapidly dropped into the quench tube mentioned previously which was now

Jan 1, 1969

By R. A. Greenkorn

This project originated in a practical problem—we needed five tracers that could be used together to locate flow paths in a pilot flood. While tracers for subsurface liquids have been used since the turn of the century,1-15 none of those reported in the literature appeared to be either consistent or quantitative enough for our purposes. Most were used in field systems without controlled experiments to determine the accuracy and precision of analysis, and many were tracers that could not be used collectively. The ideal tracer, of course, would follow the fiuid of interest exactly, traveling at the same velocity as the fluid front. But the ideal is impractical to attain because adsorption-desorption effects cause the tracer to lag behind the front; these effects, plus diffusion-dispersion effects, cause the tracer front to spread more than the fluid front. Thus, our objective was not to locate a tracer that would be ideal for all circumstances but rather, to find one that would approximately follow the fluid, or one that under controlled conditions could be corrected to calculate the movement of the fluid front. We considered tracers satisfactory—(1) if they were easy to analyze; (2) if their breakthrough-elution curves were not too different from those for the chloride ion, a tracer believed to follow the fluid front closely; and (3) if we could calculate from the curves a material balance, at 1.25-PV (pore volume) injected, within 5 per cent of that calculated from chloride curves. Of a possible 35 materials, we selected 13 tracers that could be quickly and easily identified and whose analysis was claimed to be accurate within 5 per cent. Only one of these, tritiated water, was a radioactive tracer. Radioactive tracers are easy to detect even in small quantities, but they require special handling and special equipment. Also, those that can be used together are limited because special equipment is required to separate emissions from the various tracers. Two of the original 13 tracers were eliminated in static tests to determine how accurately and precisely they could be analyzed, and to check on gross adsorption. The remaining 11 were flowed through a 9-ft linear sandstone model, and breakthrough-elution curves were obtained. Finally, three tracers were field-tested as breakthrough tracers. These tests are described in the following sections. The 13 tracers considered in these experiments were EDTA (ethylene diamine tetra acetic acid), fluo-rescein, picric acid, salicylic acid and ammonium, boron (as borate), bromide, dichromate, iodide, nitrate and thiocyanate ions, plus chloride ion and tritiated water. All but the chloride ion and tritiated water were subjected to static sand tests to eliminate the tracers that could not be analyzed quickly and accurately and to eliminate those that showed excessive adsorption. All but two of the tracers, EDTA and salicylic acid, qualified for flow tests on this basis. The procedures used in the static tests (see Appendix A for analytical details) were as follows. Each tracer (in the amount shown in Table 1) was dissolved in 1,000 ml of water. Then, 800 ml of this solution was added to 500 gm of sand, and the remaining 200 ml was reserved as a control standard. The sand-tracer mixture was agitated once a day over a 10-week period, and during this period we analyzed five duplicate samples from this mixture, along with five duplicate samples from the control solution. From the control-sample analyses, we constructed a control chart on which the sand-tracer analysis results were plotted. The control chart, and its use to determine accuracy and precision of analytical results, as well as the amount of adsorption, is described in Appendix B. The results of the static tests are summarized in Table 1, which lists the concentration c (concentration at time t) divided by c, (initial concentration). If there was no adsorption, c/c, = 1. The acceptable deviation from this value varied from tracer to tracer, depending upon the limits of analytical precision established for the different tracers. The best results were obtained with boron, bromide and dichromate, with all values falling within limits of accuracy and precision. Ammonium, iodide, nitrate and picric acid also were satisfactory, although the ammonium results were erratic. Flourescein and thiocyanate were unsatisfactory ini-

By H. L. Marcus, C. D. Turk

Titanium was physically vapor-deposited by electron beam high rate evaporation. Rates of 50,000 and 85,000Å per min at deposition temperatures of 480°, 535°, and 595°C were used. Deposited thickness ranged front 0.004 to 0.010 in. The evaporated titanium had a high degree of basal Plane texture. The specimens were tested in tension at temperatures ranging from 78° to 520°K. From the data, the yield stress, thermal component of the yield stress, and work hardening characteristics were found as a function of temperature, deposition rate, and deposition temperature. It was found that Taylor's equation, best fit the work hardening data with m = 1/2. MANY investigations have been made on the tensile deformation characteristics of commercial- and high-purity titanium.1"7 The data obtained from these experiments emphasize the fact that the mechanical properties are generally related to the method of production. The correlation of mechanical properties to production history arises from the dependence of impurity concentration on the extraction and melting technique used. Additional effects are derived from crystallographic texturing which can result from fabrication history. Lee and Backofen8 and other investigators9 have shown that crystallographic texturing in titanium sheet has a significant effect on the deformation characteristics. Bunshah and Juntz10 prepared high-purity titanium by high rate physical evaporation techniques. These authors found the deposited material to have a columnar structure with grain sizes ranging from 12 to 104 µ, depending upon the substrate temperature. The room-temperature strengths of the coarse-grained distillate were similar to arc-melted, rolled. and annealed crystal bar titanium. Commercial-purity titanium was also produced experimentally in our laboratory using high rate physical vapor deposition techniques. The commercially pure material has a finer structure than the high-purity distillate,10 and is highly textured. Since the method of preparation and degree of texturing affect the mechanical properties, a research program was initiated to determine the temperature dependence of the yield stress and work hardening characteristics as a function of high rate deposition parameters. This paper relates the results of the investigation. EXPERIMENTAL A) Material Preparation. The titanium was received in the form of commercial-grade 0.096-in.-diam wire which has a composition of 0.016 pct C, 0.0037 pct N, 0.110 pct 0, 0.011 pct H, 0.05 pct Mn, 0.051 pct Fe. balance Ti. The wire was continuously fed into a vacuum evaporation unit as shown schematically in Fig. 1. The deposition chamber was evacuated, purged with argon, and reevacuated to a pressure of 10-5 Torr which was maintained during deposition. A focused electron beam was used to evaporate the titanium from a water-cooled copper crucible. The titanium vapor was condensed onto a preheated titanium substrate. The temperature of the substrate was controlled within ±5°C for the deposition temperatures of 480°, 535°, and 595°C. Control of the input power enabled the use of two deposition rates. 50,000 and 85,000Å per min. The evaporated titanium had a final analysis similar to that of the input titanium, within experimental limits. B) Testing. The evaporated titanium was physically stripped from the titanium substrate and machined into tensile specimens with 1-in. gage lengths. In addition, tensile specimens of as received annealed 35-A titanium sheet with a 20 µ grain size and 45 pct cold-rolled 35-A were also prepared. All specimens were tested in tension in an Instron at a strain rate of 3.3 x 10"4 in. per in. per sec. Proportional limit has been used as a measure of yield strength. Tests were conducted at 78°, 220°, 300°, and 520°K. Metallography, X-ray diffraction, and electron microscopy were used to correlate structure with the deposition parameters and mechanical properties. Room-temperature X-ray measurements were made to determine the phases present. Pole figures and a scans were made to determine deposition texture. Because the vapor deposition was symmetrical about the normal to the substrate, there was no preferred di-

Jan 1, 1969

By Craig S. Hartley

An approximate expression is obtained for the energy of a closed dislocation loop in equi1ibriu)n with a constant net stress. The result obtained is valid for loops in isotropic or anisotropzc materials provided that they are suJficiently large that the energy per unit length of a segment of the loop can be approximated by that of an infinite straight dislocation tangent to the loop. It is shown that this approximation leads to very close agreement with a more rigorous calculation of the elastic energy of a circular glide loop. The Gibbs-Wulff Form, GWF, of a dislocation is the closed planar loop which has the smallest elastic self-energy of all possible loops having the same Burgers vector and enclosing a fixed area, A.' The energy of such a loop is related to the net resolved shear stress* required to expand the loop and to the stress required to activate a Frank-Read source.223 In the following sectiorls the problem of determining the form of the GWF is discussed and an approximate method for calculating its elastic self-energy is presented. It is demonstrated that the approximations employed lead to no serious errors when applied to a calculation of the elastic energy of a circular glide loop. This method is then used to obtain a closed form expression for the energy of GWFs in isotropic and anisotropic materials. THEORY Burton, Frank, and cabrera4 have proved that the relationship of the equilibrium shape of a two-dimensional array of atoms under the influence of the Gibbs free energy associated with unit length of its boundary, G(O), is that the polar plot of G(0) vs 0 is proportional to the pedal of the GWF.* The angle 0 is measured "The pedal of the polar graph ofG(0) vs0 is the envelope of tangents to the eraph.relative to some crystallographic reference direction. The difficulty in applying this result to a closed dislocation loop arises from the self-interaction of the loop. For a dislocation the energy analogous to G(0) is a function of the total configurati~n.~ Consequently the relation which determines the GWF is an integro-differential equation rather than the simple differen- tial equation which results when G(8) is a function of 0 alone. Mitchell and smialek3 and Brown~ have used the self-stress concept introduced by ~rown' to calculate the shapes of dislocations in equilibrium with an applied stress. In this approach the glide force on an element of the dislocation loop due to the interaction of the element with the rest of the loop is equated to the glide force exerted by the local applied stress. The shape of the loop is then adjusted so that the two forces above are equal at all points on the loop. It is possible to calculate the energies of such loops by noting that, for equilibrium with an applied stress, the energy is equal to pijbiAj (summation convention) where bi is the Burgers vector, p.. is the local net stress tensor, and Ai is a vector directed perpendicular to the plane of thd loop with magnitude equal to the area of the loop. Also Brown' has calculated the energy of a hypothetical polygonal GWF using the above technique and anisotropic elasticity. However, his indicated solution for the energy in the general case of an arbitrary GWF is only slightly less involved than an iterative solution of the integrodifferential equation referred to earlier. In the present work the approximation employed by DeWit and Koehler' is used to calculate the energy of a closed loop in equilibrium with an applied stress. That is, the energy of a loop segment, ds, is approximated by the product of ds and the energy per unit length of an infinite, straight dislocation in a cylinder coaxial with the tangent to the loop at the angular position of the segment. This is known as the "line tension" approximation. The inner cutoff radius of the elastic solution defines the core radius, while the outer cutoff radius is determined by some characteristic dimension of the loop. Actually, both of these radii vary with the edge-screw character of the segment. The effective core radius changes because of the orientation dependence of the Peierls width of a dislocation,8 and the outer radius should be the radial distance from the circumference of the loop to the center of symmetry of the area enclosed by the loop.g However, since the energy varies logarithmically with the ratio of these radii while depending directly on the effective elastic constants, only the effect of the latter is considered. This approximation also neglects the self-interaction of the loop segments. For small loops this will doubtless be extremely important, but for large glide loops produced by plastic deformation the self-interaction is not nearly so important in determining the energy of the loop. This point is illustrated by the following calculation of the energy of a circular loop. Consider a circular loop of radius R which lies in the XI - x, plane of an infinite isotropic continuum and whose Burgers vector makes an angle $ with xs. The first-order solution for the elastic self-energy is:'

Jan 1, 1970

By M. C. Flemings, R. Mehrabian, G. E. Nereo

Analytic expressions were developed and applied in two preuious papers to predict effects of solidification variables on macrosegvegation. In this paper, experiments are reported to test the analyses quantitatively and qualitatively. Good quantitative agreement is obtained between predicted and measured compositions for the following types of segregation (all experiments were on laboratory-size ingots of Al-4.5 pct Cu alloy): (a) inuerse segregation, (b) composition distribution in ingots solidified with unidirectional heat and fluid flow, (c) simulated centerline segregation, and (d) segregation resulting fro, change in solidification cross section. In addition, qualitative agreement of prediction of theory with experiment is obtained for (a) segregation resulting from sudden change in heat extraction during solidification, (b) centerline segregation in a bidirectionally solidified ingot, and (c) under-riser positive segregation. IN two previous papers,''2 it was shown that a variety of apparently different types of macrosegregation result from the same basic mechanism. This mechanism is the flow of solute -rich liquid to feed solidification and thermal contractions. Analytic expressions were derived and examples given of their application to predict macrosegregation. Calculations were for Al-4.5 pct Cu alloy. In this paper, we describe a series of experiments designed to test results of the foregoing calculations. All experiments were on laboratory-size ingots (weighing 10 lb or less), of A1-4.5 pct Cu alloy, nominal composition. APPARATUS AND PROCEDURE A typical mold and chilling arrangement used for unidirectional solidification is shown in Fig. 1. Before casting, this assembly was placed in an electrically heated air furnace, and heated to 680" to 700°C. When the plaster reached the desired temperature (usually 1 to 2 hr after the furnace temperature), the mold was filled through a funnel extending from the outside of the furnace into the cavity. The assembly, with liquid, was held for several minutes to allow convection to subside. The coolant, either air or water (depending on the desired solidification rate), was turned on and the ingot solidified. With the four sides and top insulated, heat removal for solidification was through the bottom surface, resulting in a fully columnar structure. Design of the casting cavity was varied, as discussed below, to produce desired macrosegregation effects. However, for castings solidified with unidirectional heat flow, the top was always open to the furnace atmosphere and temperature. The bottom sur- face rested on a chill through which the heat was extracted, and all other surfaces were insulated with plaster. In one case to be discussed, the mold design was changed to obtain bidirectional solidification. In this case, two vertical chills were used (on two faces of the mold) and the bottom was insulated. In a last case discussed, that dealing with under-riser segregation, experiments were conducted in bottom-chilled sand molds at ambient temperature. Except for this one case, all experiments were conducted in the electrically heated air furnace as described above. In many ingots, thermocouples were used to obtain continuous records of solidification. In all cases, these were chromel-alumel couples with output continuously monitored on a twelve-channel recorder. Where thermocouples were employed, these were embedded in the refractory mold walls during mold-making so their heads extended to the vertical centerline. Six to nine couples were employed, placed at intervals from the chill. METAL-MEL TING PROCEDURE Aim analysis was A1-4.5 pct Cu; alloy was prepared from high-purity aluminum (99.9 pct Al) and A1-Cu master alloy (50 pctOFHC Copper, 50 pct high-purity Al). The A1-4.5 pct Cu alloy was cast in 5- to 7-lb ingots for subsequent remelting for the macrosegregation experiments. Melting for ingot casting was as follows. After preheating the melting crucible for an hour or more, the charge was melted and superheated to a temperature of 690" to 720°C. After stirring, the melt was degassed with chlorine for 10 min. After stirring again for 1 min, a gas sample, under reduced pressure, was taken. When the sample was gas-free, the crucible

Jan 1, 1969

By John J. McKetta. Jr., Louis B. Lesem, George H. Fancher

The proration of oil produced in the field frequently is based partially or entirely upon the gas-oil ratio of wells. The measurement of the gas-oil ratio is one of the more important field tests in regulatory and pro-ration work, and the test always should be conducted according to standardized methods and procedure. Obviously, the gas-oil ratio and the volume of gas produced by a well depend upon many factors but should be independent of the method of measurement and of the devices used to measure gas and oil. Consequently, the volume of gas accompanying a barrel of oil produced by a well may be measured by any reliable and accurate device or instrument. Frequently either a critical flow prover or an orifice well tester is used for this purpose, and for a particular well the same rate of flow of gas should be obtained regardless of whether a critical flow prover or an orifice well tester is employed in the test. In Texas, when using either instrument, either Capacity Table 1 or 5' is employed in making the necessary computations. If the tables are used, a discrepancy always is found whenever the two instruments are compared by extrapolation to the same conditions of flow. Clearly, Tables 1 and 5 must be at fault in some respects. The orifice well tester and the Bureau of Mines type of critical flow prover are essentially the same instrument; both devices utilize a square-edged orifice 1/8 in. in di-ameter as the primary element, and both freely discharge gas to the atmosphere. Tables for the orifice well tester' have been published in the ranges of 0 to 15 in, of water and 0 to 40 in. of mercury (Hg) differential in pressure. Coefficients for the critical flow prover have been published for differentials in pressure greater than 75 psia. An extrapolation of either differs from the other set of data as much as 18 per cent at some points. No immediately obvious reasons for the discrepancy was found, and data available from the literature were insufficient to effect reconciliation. Consequently, a series of experiments was performed to check the available data and to determine discharge coefficients for the two devices in an overlapping range of differential pressure. The correlating equation used in preparation of tables such as Tables 1 and 5' is the so-called hydraulic equation, Q = C1 vh .....(1) The tables cover orifice sizes from 1/8 through 1 1/4 in. A second set of tables, for use with greater differentials in pressure, apply only to the 3/4, 1, and 1 1/4-in. orifice plates over a pressure range of 0 to 40 in. of Hg. The correlating equation used in preparation of the tables is Q = C2 vH(29.32 + 0.3H)/G . (2) Each of these equations is valid only for the range to which it has been applied, and neither equation is valid for extrapolation. Theoretical equations for flow through an orifice are based upon assumptions of fractionless flow and an emergent jet the size of the orifice. A multiplier, C,, called the discharge coefficient, is inserted into the theoretical expression to compensate for both frictional losses and the contraction of the jet experienced in the plane of the orifice. Buckingham3 shows that C, should vary with the ratio of upstream to downstream pressure for flow of a compressible fluid at any average linear velocity through the orifice less than the velocity of sound. Work published by the National Advisory Committee for Aeronautics4 indicates that the variation continues into the so-called critical flow region until the vena contracta coincides with the plane of the orifice. The NACA work, however, does not indicate a leveling off of the coefficient. The work of the Bureau of Mines5 for the critical flow prover was based on differential pressures greater than 75 psi and indicates that the discharge coefficient, Cd, is constant in this region at a value of about 0.86.

Jan 1, 1958

By A. Phillips, D. H. Killpatrick, V. Kerlins

The tensile failure of two dispersion-strengthened Ni-20 Cr alloys was studied and compared to the fracture of a similar alloy with no dispersoid. The fracture characteristics were studied using electron fruc-tography and transmission electron microscopy. In all three cases, the mode of failure was found to be microvoid coalescence. The failure in the dispersion-strengthened alloys was found to have initiated at the particles. The size of the dimples in the fracto-graphs was found to be related to the spacing of the particles, but not to the total elongation before failure. The elongation before failure was found to be related only to the amount of dispersed phase. These results are compared to those predicted by a theoretical model of ductile failure. THE continually increasing strength requirements for creep-resistant materials capable of long life at service temperatures above 1600"F (875"C) have developed considerable interest in dispersion-strengthened nickel-base alloys. The high yield strength of these alloys results from the presence of a dispersion of fine particles of thoria which act to impede the normal motion of dislocations. Many theories have been presented to explain the role of the dispersion in the strengthening of these alloys. A good review of these theories is presented by Ansell.' The ultimate strength of such alloys is not only related to mechanisms raising the yield strength, but also to the amount of work-hardening which occurs. This work-hardening is determined by the work-hardening rate and the amount of plastic strain before failure. Since fracture limits the amount of plastic strain, a study was undertaken to gain a better understanding of the fracture mechanisms in these alloys. Electron fractography and transmission electron microscopy were used to study the fracture characteristics in two dispersion-strengthened alloys and one similar alloy containing no dispersoid. These results are related to the tensile properties of the dispersion-strengthened alloys at room temperature and at 2000°F (1095°C). The results are also related to a theory for ductile fracture. 1) PROCEDURE Standard tensile specimens were made from 0.020-in. (0.051-cm) sheets of three different Ni-Cr alloys. The alloys had nominal compositions of Ni-20Cr, Ni-20Cr-2Th0,, and Ni-2OCr-4Th0,. All alloys were supplied in an annealed condition. The specimens were fractured in tension at room temperature to determine the effect of the dispersed thoria on the fracture appearance. The tensile properties were determined from the average of a minimum of three ten- sile specimens for each condition tested. The fracture surface of all of the alloys was examined by electron microscopy using standard two-stage plastic-carbon replica techniques. Thin foils of the dispersion-strengthened alloys were used to investigate the size and spacings of the dispersion particles, and to investigate sections of the 2 pct thoria alloy taken from areas of the specimen adjacent to the fracture surface. The thin foils were mechanically ground to 0.010 in. (0.025 cm) and then chemically polished to approximately 0.001 in. (0.003 cm) in a solution of 29 g of ferric chloride and 10 ml hydrochloric acid in a liter of water. The polishing solution was maintained at 150"F (65°C) during the thinning operation. The final thinning of the foil was done electrolytically using a solution of 700 ml ethanol, 100 ml 2-butoxy eth-anol, 120 ml distilled water, and 78 ml perchloric acid (70 pct). The potential was maintained at 15 v and the bath temperature at -20°~ (-29°C) during the thinning operation. The final thickness of the foil was approximately l000A as determined from the width of twins boundaries observed in many of the foils. 2) RESULTS AND DISCUSSION The electron fractographs of the fracture surfaces of the alloys are shown in Figs. 1, 2, and 3. The normal interpretation of this type of fractographz is that, as a result of the difference between elastic and plastic properties of the matrix and the particles or other inhomogeneities in the alloy, microvoids are formed

Jan 1, 1969

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

AGGLOMERATION U.S. 4,067,727 - In the sintering of a charge of iron oxide ore, a fuel and a flux on a travelling grate machine, the dust problem is minimized by providing a plurality of cooling zones and by directing heated dust-laden air from a first cooling zone to the sintering zone wherein the dust is filtered from the air by the material being sintered. Air from a further cooling zone can be exhausted directly to the atmosphere. Dust removal in the cooling zone is improved by using a purging zone in which higher pressure air agitates the dust in the sintered material. This patent is a division of U.S. Patent No. 3,973,762, dated Aug. 10, 1976. F. Cappel, assigned to Dravo Corp. Jan. 10, 1978. 6 pp. (75-5). Filed: 4-1-76 (672,748).

Jan 1, 1979

By Hsun Hu, B. B. Ruth

The rates of migration of high-angle boundaries in zone-refined aluminum crystals rolled 20 to 70 pct in the (110)[i12/ orientation were studied. Following a recovery anneal at an appropriate temperature to stabilize the polygonized structure, boundary migration rates of artificially nucleated grains were measwed isothermally at several temperatures. Results indicate that the rate of boundary migration depends strongly on the amount of deformation and on the cell size of the polygonized matrix, and is related to the driving free energy by a power function. The degree of anisotropy in growth 0.f the re crystallized grains nn&apos;th preferred mientation is independent of deformation; the migration rates of the fast-moving and the slow-moping boundary segments of a gowing grain differ by as much as one order of magnitude. The actir\ation energy fm a grain boundary migration, although nearly the same for both the fast-moving and the slow-moving boundaries for a given deformalion, decreases from 45 to 30 kcal per mole with an increase in deformation from 20 to 70 pct reduction. Re crstallization by the growth of the artificially nucleated grains results in preferred orientation. The Percentuge of&apos; grains favorably oriented for growth increases with increasing deformation. None of these grains corresponds to the ideal Kronberg-Wilson orientation relationship. The observed growth aniso-tropy is discussed in terms of boundary structure. The boundary velocity as a function of the cell inter -facial area, or the driving free energy, is discussed in the light of current theories of boundary migration. It is well established that recrystallization with re-orientation occurs by the migration of high-angle boundaries of strain-free grains. The driving force for this process is provided by the free energy stored in the metal during deformation. A quantitative study of the effect of varying driving force on grain boundary migration in deformed metals has not been possible heretofore, primarily because of: 1) concurrent recovery steadily decreasing the available driving free energy for boundary migration, &apos;-3 and 2) in-homogeneity of strain in the deformed metal.4 Aust and Rutter3 studied grain boundary migration in striated single crystals of zone-refined lead. Although the driving free energy in such crystals remains unaltered during annealing, this method does not provide a range of driving free energies over which measurements of grain boundary migration can be made. In the present investigation, the rates of migration of high-angle boundaries in deformed aluminum zone- refined single crystals were studied at various temperatures, after deformation ranging from 20 to 70 pct reduction by rolling at -78°C in the (ll0)[i12] orientation. The boundary migration rates along different crystallographic directions were determined under steady-state conditions, i.e., in the absence of competing recovery processes or impingement of recrystallized grains growing into the deformed single crystal matrix. Simultaneous recovery was eliminated by suitable anneals prior to the boundary migration measurements. The recrystallized grains, which grew a ni so tropically into the homogeneously polygonized matrix, developed flat boundary segments during early stages of growth. These boundary segments subsequently migrated along a direction approximately normal to the boundary plane into the matrix rystal. Increasing deformation over the range employed was estimated to increase the driving free energy for boundary migration by about five times. The kinetics of the boundary migration process, examined under these conditions, indicate that the boundary velocity is greatly affected by a small change of the driving free energy in the matrix crystals. These results were examined in the light of the current theories of grain boundary migration. EXPERIMENTAL PROCEDURES Single crystal strips (9 by 1 by 0.125 in.) of zone-refined aluminum, were seed-grown by the Bridgman method in a high-purity graphite mold (<lo ppm ash) at 1 in. per hr. Precautions were taken to minimize contamination of the metal during crystal preparation and subsequent handling. Spectrographic analysis of the metallic impurities in the grown crystals is Qven in Table I. The crystals were rolled in the (110)[112] orientation at -78°C to various reductions in thickness, ranging from 20 to 70 pct, in 10 pct increments. The desired reduction was achieved by many rolling passes, each being no more than 0.002 in. To minimize surface friction, the crystal was rolled between two thin layers of teflon. For those crystals rolled more than 40 pct, it was necessary to remove the disturbed surface layers by electropolishing at -5" to -10°C at an intermediate stage of rolling. The edges of deformed crystals were removed by a jeweler&apos;s saw while submerged in alcohol at -78° C to obtain samples of about ? by i in. The distorted metal at the cut edges and the surface layers were then removed by electropolishing, with removal of a minimum of 0.004 in. from each surface. The thickness of the crystals prior to rolling was chosen so that the final thickness was 0.025 in. for all samples. These deformed single crystals were each prean-nealed for 1 hr at an appropriate temperature in the range of 130" to 280°C, depending upon the amount of deformation. The purpose of this preannealing was to

Jan 1, 1970

By C. A. O’Connell

Surface exploration drilling at Mufulira started in 1928, with drillhole No. 1 intersecting ore near the eastern fringe of the deposit. Subsequent drilling along strike intersected ore until the western fringe was fixed some 7500 ft west of drillhole No. 1. Further intensive drilling down dip disclosed a large triangle of ore with its apex 3350 ft deep. It contained approximately 11 6 million tons of ore at 4.41% total copper in three superimposed orebodies. The east and west limits of the orebodies were presumed to have a pronounced rake to the north with a strike length of 8000 ft. Subsequent exploration underground seemed to bear out this presumption to the 1150 ft level. In 1947, attention was directed to the area west of the known orebodies in conjunction with plans for increased production and increased depth of the mine workings.

Jan 12, 1962