Search Documents

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall's work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann's approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen's approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

Few people in the industry today are competent to comment on the O.G. system for vessel covers, but with papers as well prepared as Mr. Bradley's we will soon be well informed. I would like to direct these comments to Mr. Klaes of Ford Motor Company. Mr. Klaes' description of their steaming hood agrees with our experience at Weirton. We have been able to stay within design limits and, as a result, have had few problems with our auxiliary equipment. Our main problem, as with Ford, has been thinning of our vessel cover tubes. At Weirton, controlled circulation, high pressure boilers are in use as heat recovery units above the BOP vessels. The boilers are provided with "off cycle' oil firing equipment. A Venturi type wet gas scrubber follows the boiler to complete the vessel draft system.

Jan 1, 1972

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.' : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*'" Exotic recovery processes have been considered primarily for ' perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

By M. B. Bever, A. M. Reti, A. K. Jena

The results of this investigation show that in the system SnTe-PbTe l) the solid solutions have small exothermic heats of formation relative to the binary compounds, 2) solid-solution hardening is almost absent, 3) the tin and lead atoms are .randomly distributed on the sublattice occupied by them and do not undergo an ordering transition during a thermal treatment designed to promote such a transition, and 4) the lattice parameter changes linearly with composition. These findings suggest that the solid solutions of tin telluride and lead telluride approach ideal behavior. THE binary compounds SnTe and PbTe form a continuous series of solid solutions.' Information on several physical properties of these solid-solution alloys has been published.1"3 In the work reported here, the heats of formation, microhardness, and lattice parameters of these alloys have been measured and the possibility of an order-disorder transition has been investigated. Order-disorder transitions occur in some solid solutions of binary compounds. In the system Bi2Te3-BizSes, for example, the electropositive bismuth atoms and the electronegative tellurium and selenium atoms always occupy separate layers. In the disordered alloy Bi2Te2Se, the tellurium and selenium atoms are randomly distributed on the layers occupied by them, while in the ordered alloy they occupy distinct layers.4 The NaC1-type (Bl) structure of SnTe-PbTe alloys consists of two sublattices, one of which is occupied by the electropositive tin and lead atoms and the other by the electronegative tellurium atoms; any ordering would be expected to occur in the sublattice occupied by the tin and lead atoms. PREPARATION OF SPECIMENS Polycrystalline specimens of PbTe and Sn1-xPbxTe (x = 0.25, 0.50, and 0.75) were prepared by melting stoichiometric amounts of lead (99.999 pct), tin (99.98 pct), and tellurium (99.999 pct) in evacuated and sealed Vycor tubes. Because of the deviation of tin telluride from the stoichiometric composition5 this compound was prepared by melting 49.8 at. pct Sn and 50.2 pct Te. The tubes containing the melts were quenched into water; the solidified ingots were removed from the tubes and annealed for 2 weeks in vacuum (PbTe approximately 100°C below its melting point, the three alloys 100°C below their solidus tem-

Jan 1, 1969

By Sheldon Rideout, E. L. Kamen, B. S. Lement, Paul A. Beck, W. D. Manly

The 1200°C isothermal sections of the following ternary phase diagrams were investigated: Cr-Co-Nil Cr-Co-Fe, Cr-Co-Mot and Cr-Ni-Mo. In all these systems the u phase was found to form extended solid solutions. Two new ternary phases of unknown structure were identified. The existence range of intermediate phases of transition elements was correlated with 3d electron vacancy concentrations. THE occurrence of extensive ternary d solid solutions in the Cr-Co-Ni and in the Cr-Co-Fe systems was described in a brief note.' More recently d- solid solutions were also found in the Cr-Fe-Mo system by two independent groups of investigators.2,3 The existence of binary d phases in the V-Co and V-Ni systems, predicted in ref. 1, was experimentally discovered recently by Duwez and Baen and independently by W. B. Pearson, J. W. Christian, and W. Hume-Rothery.5 Duwez and Baen stated two general conditions for the occurrence of the d phase in alloys of the transition elements: "(1) The atomic diameters of the two metals do not differ by more than 8 per cent. (2) One of the two metals has a body-centered cubic structure while the other is face-centered cubic, at least in one of its allotropic forms." In the course of an extensive research program conducted at this Laboratory under the sponsorship of the NACA, several ternary systems, containing d solid solutions and also certain new ternary phases, were investigated. The present report describes the investigated portions of the 1200°C isothermal sections of the following ternary phase diagrams: Cr- Co-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo. It was found that the range of existence of the d phase in these four ternary systems, as well as in one of two ternary systems which were investigated by others, can be fairly consistently described in terms of electron vacancy concentrations. This supports the suggestion of Sully and Heal" that the d phase is an electron compound. Experimental Procedure The ternary alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. Lot analyses of the metals used are given in Table I. Specimens of all alloys were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting mainly of

Jan 1, 1952

By B. D. Cullity, J. T. Norton, M. Telkes

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

By M. E. Shank, J. Wulff

At the present time, the designer of dies for metal powder pressing is handicapped by relative ignorance of stress distribution and frictional effects at the interior surface of the die. Unckell was the first to develop a method for the study of wall friction. He used three Brinell balls on which the die rested during pressing. The total frictional wall force was determined by the size of impression these balls left on a soft metal plate. Since the method does not give radial pressures, or distribution of such pressures, coefficients of friction could not be determined. Although Unckel measured density distribution, he was not able to determine radial or shear stresses. Shaler2 has proposed theoretical expressions for the stress and density distribution within cylindrical compacts during pressing, in accordance with the experimental results of Kamm, Steinberg, and Wulff.3 By application of Siebel's method,4 Kamm et a13 plotted stress trajectories for two compacts. From the stress trajectories they calculated coefficients of friction from point to point along the die wall. As pointed out by Shaler in the discussion of Ref. 3, these values are based on progressive point-to-point calculations on finite size grid squares across the compact. In the region of the die wall such calculated values may therefore have considerable cumulative error. The purpose of the present paper is to develop an experimental method by which the nonhydrostatic pressures and shears acting on the interior wall of a cylindrical die can be measured. Such measurements can then he correlated with existing data to aid in the explanation of the pressing process. The method used is based on the elastic: properties of the thick-walled tube used as the die. The principle of super-position of force systems on an elastic body is assumed to hold. Electric strain gauges were mounted in adjacent positions on the exterior die wall in order to get an exact measurement of the variation of tangential strain over the length of the die during pressing. While in this paper, measurements in terms of only tangential strains are considered, it is well to note that similar calculations may be set up for axial strains. The latter are not preferred, since they tend to be smaller than the tangential strains and therefore permit less sensitive measurements. Discussion in this work is restricted to compacts pressed from both ends, since the elastic deformation of the die is then more amenable to analysis. Before choosing the electric strain gauge method, a more direct line of attack was considered and discarded. The discarded idea was the insertion of a pressure gauge through a hole in the die wall.* The gauge would have been in the form of a small piston. If pressure were exerted against such a gauge, it would move outward along a radius of the die. One disadvantage of the scheme is its inability to measure shears along the die wall. Another more serious disadvantage is the disturbance caused by the device itself. It would serve to change the forces it was designed to measure. No matter how small the movement of the gauge, when pressure is applied a discontinuity would exist in the wall surface at that point. Due to the stress concentration caused by the hole, abnormal deflections of the die wall would occur around the gauge. During pressing, powder would be forced into the resulting depression. The depression would then become larger with increasing compacting pressure. Powder, not being a fluid, is capable of supporting shear. The ease with which it would flow into the die wall depression to further move the piston is an indication, not of the radial pressure at that point, but of the state of shear retarding the movement. Thus the "pressure" gauge is really a criterion of flowability, and of the capability of the powder to support shear. For these reasons, it was decided that the electric strain method, herein employed, was more reliable, if more indirect. The gauges and lead wires, mounted on the external die wall do not in any way affect the behavior of the metal powder or the die during pressing. Theory of the Method THE EFFECT OF RADIAL PRESSURE ON THE DIE WALL Effect of a Single Small Band of Hydrostatic Pressure Consider a die which is a thick-walled cylinder of outer radius R. and inner radius Ri. If over a small finite length L there is a normal pressure P, a tangential strain distribution at the outer wall results. This is shown schematically in Fig 1. The exact shape of the curve may he predicted by an extension of the theory of a semi-infinite beam on an elastic foundation.6 This

Jan 1, 1950

By J. H. Bowden

On the night of January 23d, 1889, Erich C. Schaufuss, a member of the Institute, while engaged in making the regular mine-surveys in No. 4 Slope of the Susquehanna Coal Co, at Nanticoke, Pa., was killed by an explosion of fire-damp. The catastrophe, which cost another life also, is attributed to the carelessness of the " fire-boss" leading the party, who advanced with a naked lamp into a chamber

Jan 1, 1889

South Carolina Geological Survey, University of South Carolina, Columbia, S. C. Stephen Taber, State Geologist Two bulletins have been issued by the South Carolina State Geological Survey: Bulletin 1, A preliminary report on the clays of South Carolina (1908), and 2, Catalogue of the mineral localities of South Carolina. Members of the staff of the Department of Geology of the University have published many papers which have appeared in print from various sources

Jan 1, 1933

By R. S. French, W. R. Hibbard

M. Balicki—As one who some years ago spent much time searching for an alloy with high thermoelectric power that would be suitable for heat energy-electric energy converter based on the principle of a thermoelectric pile, I would like to make a few comments touching upon that aspect of this excellent paper. The specifications which one of the authors has formulated so aptly do not appear to me as complete, and I would like to add to them the following two demands: (1) Melting point not less than 500°C and (2) elongation on 2 in. at least 5 pct. Condition 1 would insure good thermodynamic efficiency of the pile by permitting a reasonably high temperature of the hot junction and at the same time making it suitable for such application as salvage of vast amounts of energy which is lost in the form of sensible heat of waste gas leaving industrial and other furnaces. Condition 2 is also a very important one; particularly, because of the fact that all elements and alloys which exhibit attractive thermoelectric properties seem to be as a rule very brittle. The design, erection, and maintenance of a pile incorporating a brittle material in one of the most crucial parts of the converter would be a very difficult and costly affair indeed. To illustrate this point I may mention great difficulties I encountered when trying to make thermocouples of silicon. Casting of 1/4-in. rods in iron or graphite mould yielded only broken pieces which had to be welded into a bar. Such a bar had to be handled very carefully during the determinations. Raising the molten silicon by vacuum into a silica tube and solidifying it there solved the problem of stability as well as that of electrical insulation of a bar. On tests this bar (98.5 pct Si) showed dE/dT = — 275.5 microvolts per degree C vs. copper. Thermocouples made of this grade of silicon and pure nickel developed 0.39 v when temperature of the hot junction was approximately 1000°C. The possibility Dr. Gonser has mentioned of trying to impart to metals good thermoelectric properties by alloying them with silicon, has been considered. The preliminary survey which I have made was, however, disappointing. Perhaps, it will be advisable to record the results obtained (table VI), as this might save repetition of search in fields already covered.

Jan 1, 1951

President Howe: It is, of course, not easy to discuss off-hand the paper which Mr. Becker has presented with so much lucidity. I will only make one remark, which is outside of the line of his argument, and concerns merely a passing allusion in his paper. Mr. Becker speaks of the fact that glass breaks with a flat or conchoidal fracture, and that steel shows a rough or " cupped " surface of frac-

Jan 1, 1895

By R. A. Conkling

DORSET HAGER, Tulsa, Okla. Recently we have, been doing a little work along the same lines Mr. Conkling has outlined iii his paper. I am not prepared to say that Mr. Conkling is not correct but our results do not agree with his. I think it is a question of difference in correlation and interpretation of the well records. Our cross-section of the Cushing pool does not agree with that of Mr. Conkling and we find instead of the beds thickening in the syncline, there is a tendency to thicken on top of the anticline. We took the north dome of the Cushing field, and are now trying to get all the records. It will probably be another month before we have all the data complete but our results at present do o not agree with those of Mr. Conkling at all.

Jan 4, 1917

By W. R. Clough, M. E. Shank

IT has been noted in a study of the flow and fracture of nodular cast iron under biaxial stress conditions (complete results of which will be published later) that when this metal is subjected to stress it may undergo a striking density change. Such behavior was first determined by strain gage measurements made on tensile test specimens, and has since been substantiated by other types of measurement. The chemical analyses and mechanical properties of several nodular irons to be discussed here are given in Tables I and 11. Tensile data for iron A was obtained from a hollow cylindrical combined stress specimen of the same dimension as those used by L. F. Coffin, Jr.1 in his investigation of gray iron properties. Standard 0.505 in. solid tensile-test bars were used for irons B and C. On each specimen type, A-8 wire resistance strain gages were used—two diametrically opposing gages in the axial direction, two in the tangential or hoop direction. By subtracting elastic strains from the measured strains, the plastic strains could be calculated. By assuming that radial and tangential strains are numerically equal, a measure of permanent volume change can be obtained by summing the plastic strains. This appears to be a good assumption, since the metal either fractured, iron A, or readings were discontinued, irons B and C, long before necking took place. This calculated variation of volume increase with stress is given for irons A and B in Fig. 1. Data for iron C is almost identical with that for iron B. The volume change indicated by Fig. 1 has been substantiated by a more direct type of density measurement. A method developed by S. G. Fletcher and' Morris Cohen,' and completely described in the discussion of their article, has been used. The accuracy of specific volume measurement has been estimated as 0.00002 cu cm per gram. Essentially the method consists of weighing a sample in air and then immersed in water. Measurements were made before and after straining the material. The results shown in Table I11 were obtained by means of half-size (0.252 in. diameter, 1 in. gage length, 3/8-16 threads) tensile specimens. Initial measurements were made on the whole specimen before stressing. After stress-

Jan 1, 1955

By C. W. Kovach, A. Moskowitz

Studies were undertaken to investigate the effects of manganese content on the machinability and other Properties of a free machining martensitic stainless steel (AISI Type 416). Machinability was found to be significantly improved in steels of high manganese content, and a direct relationship was obtained between machinability and steel Mn:S ratio. As the manganese content of the steel increases, the sulfide Phase present changes from CrS to (FeMn)Cr2S4 to (MnFeCr)S, and finally to MnS. The average sulfide inclusion hardness decreases through the same range of increasing manganese content. The mechanism for machinability improvement is discussed in terms of a soft ductile sulfide affecting deformation in the secondary shear zone. Type 416 containing relatively high manganese for improved machinability shows good general properties. The effects of increasing manganese content on mechanical properties, cold formability, and corrosion resistance are described. THE addition of sulfur is commonly used to improve the machinability of stainless steels. However, little attention has been paid in the past to the composition and characteristics of the sulfur-containing phase or phases present in these resulfurized steels. Recent information on the properties of sulfide phases, and their role in metal cutting, suggests that variations in these phases could have critical effects on machin-ability, as well as important effects on formability and other properties such as corrosion resistance. Manganese, chromium, and iron are strong sulfide forming elements present in stainless steels! of these, manganese has the greatest sulfide forming tendency and iron the least.1"1 The manganese content of resul-furized 13 pct Cr steels, often about 0.5 pct, can be insufficient or only barely sufficient to combine with the sulfur that is present; thus, the precise level of manganese can strongly influence the nature of the sulfide phase. Sulfide phases which may be present in stainless steels have been reported to include CrS, a spinel-type sulfide, chromium-rich manganese sul-fide, and manganese Sulfide.5,6 Detailed phase relationships for the Fel3Cr-Mn-S system have been reported by the present investigators,7 and a portion of this work will be referred to subsequently in this paper. Recent work by Kiessling6 and Chao et a1.8 has shown that sulfide phases can display wide variations in hardness, and may undergo considerable plastic deformation under isostatic loading.9-12 Early theories of metal cutting attributed the influence of sulfur to a lubricating effect. It is now apparent that the influence of the nonmetallic inclusions and their properties on crack initiation, deformation in the shear zones, and boundary films must also be considered in relation to the machining process. This paper presents the results of studies conducted to relate machinability to the various sulfide phases which occur in stainless steels. This work has led to the development of alloys with improved machinability, and has generated information on the effects of inclusions on metal cutting processes. Effects of sulfide inclusions and steel composition on other important metallurgical properties are also discussed. MATERIALS For drill machinability and inclusion studies, 10 lb laboratory heats were melted in an air induction furnace. These heats were made with sulfur contents be tween 0.10 and 0.50 pct and manganese contents be tween 0.05 and 3.0 pct. Residual elements were added to the heats in amounts typical for commercial steels. The typical compositional range covered by the heats is shown below: C Mn P S Si Ni Cr Mo Cu N 0.10 0.05 0.007 (M0 0.40 0.40 13.0 0.20 0.10 0.03 3.0 0750 The laboratory ingots were forged in the temperature range of 1800" to 2100°F to 3/4-in. sq bars, and all bars tempered to a hardness aim of 200 Bhn prior to testing. Because of differences in composition and tempering response, the tempered bars showed some variation in hardness (175 to 275 Bhn) as well as variations in delta ferrite content (0 to 50 pct). Composition, hardness, and delta ferrite content were considered in the analysis of the machinability data. Additional tests involving tool-life evaluation and determination of other properties were conducted on materials from commercially melted and processed 15-ton electric furnace heats. TESTS AND PROCEDURES Machinability of the laboratory heats was evaluated in a drill test. In this test, 1/4-in. diam holes, 0.4 in. deep, were drilled alternately in a test bar and in a standard bar for a total of four holes in each. This sequence was repeated three times using a freshly sharpened drill each time. The average time required to drill a hole in the test bar was compared to that for the standard bar. A drill machinability rating was assigned to the test bar relative to a rating of 100

Jan 1, 1970

By John C. Bilello

The brittle fracture behavior of cold-worked sintered tungsten was studied over the temperature range 4.2° to 298°K using a high-sensitivity strain measuring system and electronfractography. Similar observations were made on a swaged electron beam zone-refined monocrystal. In sintered tungsten irreversible plastic deformation was observed during cyclic load-unload tests at stress levels well below the fracture stress for all temperatures, but general microyielding could be detected only down to 202°K. For the zone-refined samples macroyielding occurred at all test temperatures with evidence for twinning below -202°K. The fracture stress of the sintered tmgsten was virtually independent of temperature, while the zone-refined crystal showed a 2.3 times increase over the same temperature range. Electronfractography confirmed the presence of numerous rod-shaped and spherical submicroscopic voids which ranged in diameter from 1400 to 4300A in the sintered tungsten; no voids could be found in the zone-refined tungsten. Contrast effects observed on the replicas in the vicinity of certain voids indicated that plastic deformation could be induced by the local stress concentration. It has been suggested that the presence of these voids may be responsible for the low-temperature brittle failure of sintered tungsten. Based m this suggestim und on the evidence obtained here, a dislocatim model is presented to account for the brittle behavior of sintered tungsten. In this model slip, which is induced by the local high stress concentration in the region at the edge of a favorably oriented void, could cause the void to grow to a microcrack of critical size. STUDIES of brittle fracture in bcc metals have led to the well-known experimental relationships between grain size, yield stress, fracture stress, and temperature which have formed the basis for the various dislocation pile-up1-3 or interaction4'= models for slip-induced microcrack nucleation. While microcracks can be nucleated by deformation twins,6,7 there has been no direct evidence furnished by transmission electron microscopy to support conclusively either the Zener pile-up or Cottrell dislocation reaction models for producing micro-cracks in all "brittle" materials. In addition to the "inverse" grain size relationship for yield and fracture stresses the cottrel14 theory predicts that the fracture stress below the transition temperature should behave in a fashion similar to that of the yield stress above this temperature. Such behavior has been verified for several bcc metals.8-10 With reference to both grain size effects and the tem- perature dependence of the fracture stress below the transition temperature, the behavior of sintered tungsten appears anomalous. Early work by Bechtold and Shewrnon 11 showed no apparent temperature dependence of the fracture stress below the ductile-brittle transition temperature (DBTT). They attributed this result to the intergranular nature of the fractures observed. More recent work by Wronski and Four-deux12'13 on considerably purer material did not show any systematic relationship between the fracture stress and temperature below DBTT. The dependence of flow and fracture stresses on grain size is also not clearly established for sintered tungsten. Koo, for example, has shown that the DBTT for sintered tungsten depended chiefly on the annealing temperature and was relatively insensitive to the actual grain size achieved. Using electrofractography and transmission electron microscopy, Wronski and Fourdeuxl3 showed that numerous spherical and rod-shaped submicroscopic voids could be found in sintered tungsten but not in melted tungsten of nominally the same purity. They suggested that these voids could be responsible for the temperature insensitivity of the fracture stress below the DBTT. In the present work the temperature dependence of the fracture stress for high-purity commercially sintered tungsten has been determined. The presence of submicroscopic voids in sintered materials was confirmed, and these were studied in detail to examine the role they could play in nucleating brittle fracture. A dislocation model is suggested which could cause an inherent spherical void to lengthen into a Griffith crack of critical size. EXPERIMENTAL PROCEDURE Commercially sintered tungsten rod was obtained in the as-swaged condition from Sylvania. A zone-refined crystal was obtained from the same source. This crystal was grown by giving three zone passes (at 25.4 cm per hr) to a sintered rod of high-purity tungsten. The rod axis prior to cold working was -15 deg from the [110] direction. Originally the zone-refined rod was -6 mm in diam; it was reduced to -3 mm by eight swaging passes, at high temperatures, with each step having about the same reduction of area. The final swaging step gave a 7.5 pct reduction of area at 1050°C. All swaging operations were performed in a hydrogen atmosphere. For the sintered rod a similar working schedule was employed. Metal-lographic examination of the sintered material revealed that the cold-worked structure had an apparent grain diameter of -25 u transverse to the swaging direction (obtained by the intercept method). In the longitudinal direction cold-worked grains were approximately 1.5 to 2 times their diameter. No distinct fiber structure could be observed optically for the zone-refined rod. The cold-worked structure in the

Jan 1, 1969

By MALCOLM FRASER

I was delighted to be invited to be patron of this Joint Conference, but the challenging task you have set yourselves, and your speakers' depth of expertise, deny anyone, even the patron, the opportunity to be patronizing. Australia's history has been inextricably linked with the fortunes of our great mining industry. That link will remain. Just as the gold rushes of the last century, and the discoveries at Kalgoorlie and Broken Hill changed the lives of generations, so the more recent development activity in iron ore, bauxite, nickel, coal, and uranium are having a significant impact on the lives of Australians today. The minerals industry has contributed to Australia's jobs and prosperity. Mining is not free of problems, but so long as safeguards are strong and appropriate the net benefits the mining industry brings Australia will continue to be enormous. We rely on our mining industry to find, prove, develop and sell our minerals profitably, and my Government is committed to maintaining a healthy mining industry. In the past year there have been positive signs of a resurgence in exploration and development. The North-West Shelf ventures are spending $50 million on a feasibility study to work out the extent of future investment in that project; exploration expenditure for minerals other than petroleum increased by 34 per cent in 1976-77 to $134 million; petroleum exploration increased dramatically last year almost doubling to $94 million-this year it is projected to reach $125 million.

Jan 1, 1978

By George M. Enos, Robert J. Anderson

This paper gives a summary of tests made on the accelerated electrolytic corrosion of the tin brass, 70:29:1 copper-zinc-tin (admiralty metal), of different grain sixes in various electrolytes. There has been great difference of opinion as to the effect of grain size on the corrosion rate of brass, particularly in condenser-tube practice, but so far as is known no information has been published on the subject. It has been assumed, on the basis of the amorphous-cement theory, that fine-grained brass would corrode more rapidly than coarse-grained because the amorphous phase is more soluble than the crystalline and there is more cement per unit area exposed in the fine-grained material. In previous work on the corrosion of metals and alloys in acid mine waters from coal mines,1,2 it was found that the grain size, within a restricted range, had practically no effect on the corrosion of the brass 70:29:1 copper-zinc-tin: In the tests made, samples of three grain sizes were included; viz., 0.025, 0.035, and 0.075 mm. diameter (1600, 817, and 177 gr. per sq. mm., respectively), and the average losses on exposure to the most acid of three waters were 7.07, 6.80, and 6.72 mg. per sq. cm. per day (24 hr.), respectively. No distinguishing features were observed on microscopic examination of the corroded samples. In two other mine waters, the corrosion losses were substantially the same for the respective samples. These tests were -incidental to other tests and were not sufficiently comprehensive to warrant drawing definite conclusions. In further work with the accelerated electrolytic corrosion test, as developed recently in the Bureau of Mines, tests were made

Jan 1, 1924

By C. R. Forbes, J. C. Barton

Many different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. Description" of Bits Tested 'I'he 4-point bits were the usual shaped bits commonly made on the Leyner sharpener, with 14' taper on the wings and a 90" angle between cutting edges. Some tests were run at 85 Ib. pressure with a 4-point bit made with a 50 taper on the wings; this bit was formed with the Carr bit dies. The 6-point bits were the usual shaped bits made on the Leyner sharpener. The Carr bits were made with a 5º taper and an angle of 100" between cutting edges.

Jan 1, 1918

By Richard F. Miller

Recent studies of creep have made it apparent that plastic deformation may occur in metals under stresses less than the elastic limit as determined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapselll said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was determined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instruments by A. W. Hanson4 on zinc and by Podaschewsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc. AppaRatus The creep-testing apparatus developed for this work is shown in Figs. 1 and 2. The extensometer A is sensitive enough to detect changes in length of 3.3 X 10~6 in. per in., and yet can be used into the plastic range without injury to the apparatus. The specimen,

Jan 1, 1936

By F. N. Lathe

In 1882, The Arizona Copper Co., Ltd., acquired producing copper mines at Metcalf and Morenci (locally called Longfellow). Metcalf is situated a distance of 7 miles, and Morenci a distance of 6 miles from the general office of the company at Clifton, Ariz. A reduction works with five blast furnaces was built in the center of the town of Clifton in 1884 and operated until January, 1914. Concentration of oxidized ores was begun in 1890-1891, in a mill built adjoining the smelter, and id October, 1893, a leaching process was started for treating tailings from the oxide mill. A sulphide concentrator with 300 tons capacity was built at Clifton and started treating chalcocite ores in July, 1896. This was the first mill to treat low-grade copper-siilphide ores successfully. Another concentration mill for sulphide ores was erected at Morenci in 1900. The sulphide mills are now being remodeled to treat ores by concentration and flotation, with a capacity of 4,000 tons at Morenci and 500 tons at Clifton. The leaching plant has not been running since September, 1914. The average yearly production from this company's mines and reduction works from 1885 to date has been: Pounds 10 years ended 1894................................... 6,864,902 10 years ended 1904................................... 20,439,614 10 years ended 1914................................... 32,665,905 Part of year 1915, to Sept. 12........................... 30,206,106 4 months of 1916, to June.............................. 15,964,840 June, 1916........................................... 4,900,000 Construction on a new smelting plant was started in February, 1912, and finished in February, 1914. In the Transactions, vol. 49, E. Horton Jones published "Unit Construction Costs from the New Smelter of the Arizona Copper Co., Ltd.," which fully describes the construction of this plant, with details of costs.

Jan 1, 1917