Search Documents

By R. E. Cole, A. M. Gaudin

OLEIC acid, a standard flotation reagent, has generally been preferred to other fatty acids. Because oleic acid differs from saturated fatty acids by the presence of one carbon-to-carbon double bond and because the flotation operation is one in which extremely intimate exposure of the reagent to oxygen is obtained, it appeared possible that the value of oleic acid as a flotation collector was related to the oxidizability of its double bond. To test this hypothesis, the floated mineral, fluor-ite, was leached with a solvent capable of extracting the adsorbed reagent and the extract was analyzed.' Results show that oleic acid is not oxidized during flotation, although some oxidation can be obtained if the flotation operation is repeated many times and if oxygen in place of air is employed as the gas during flotation. Incidentally, it was found that lino-leic acid which has two nonconjugated double bonds is not affected appreciably more than oleic acid. Linolenic acid which has three nonconjugated double bonds is measurably altered even during one flotation step, using air. The fatty acids used, from the Hormel Foundation, were of the highest purity. The quantity of fatty acids employed in each test was sufficient to float the mineral, but less than the theoretical amount required to form a monolayer at the mineral surface. The purpose of this limitation was to eliminate droplets of oil smeared on the adsorbate-covered mineral surface. The mineral was dried in vacuum at about 60 °C. Effective leaching was obtained by use of a solution of 1 pct hydrochloric acid in absolute alcohol. The extract was separated from the solvent by distillation, with final recovery of the extract in carbon tetrachloride. The identity of the extract was tested by a combination of analytical procedures including infrared spectroscopy, saponification number, iodine number, and index of refraction. At the outset, great hopes for accurate quantification of oleic acid oxidation had been entertained in regard to the method of infra-red spectroscopy. Unfortunately, because the double bond in the oleic acid is so sym- metrically located at the center of the molecule that it provides very weak absorption bands, accurate quantitative analyses were not obtained. Nevertheless, infra-red spectrograms suggested the absence of double-bond oxidation during flotation. Iodine number, semi-micro method, provided a critical test of the extent to which fatty acids oxidized during flotation, see Table I. The index of refraction was used in a qualitative rather than quantitative fashion, and its findings corroborated those obtained by the iodine-number method. It is concluded, in the case of fluorite and C-18 fatty acids having one or two nonconjugated double bonds, that there is practically no change of the fatty acid molecule or ion during the flotation operation. It would appear, therefore, that the extraordinary utility of these reagents is related to some property of the compounds other than the oxidizability of their double bonds. Acknowledgment The research reported herewith was sponsored by the Research Division, U. S. Atomic Energy Commission, and for this help the authors express their appreciation. Reference 'R. E. Cole: "Double-Bond Reactivity of Oleic Acid During Flotation." Thesis submitted in partial fulfillment of the requirements for the degree of M.S. at the Massachusetts Institute of Technology.

Jan 1, 1954

By E. W. Filer, L. S. Darker

ONE of the primary purposes of this investigation was to determine how far blast-furnace metal and slag depart from equilibrium, particularly with respect to sulphur distribution. In studying the equilibrium between blast-furnace metal and slag, there are two approaches that can be used. One method is to use synthetic slags, as was done by Hatch and Chipman;' the other is to equilibrate the metal and slag from the blast furnace by remelting in the laboratory. In the set of experiments here reported, metal and slag tapped simultaneously from the same blast furnace were used for all the runs. The experiments were divided into two groups: 1—a time series at each of three different temperatures to determine the t.ime required for metal and slag to equilibrate in various respects under the experimental conditions of remelting, and 2—an addition series to determine the effect of additions to the slag on the equilibrium between the metal and slag. An atmosphere of carbon monoxide was used to simulate blastfurnace conditions. The furnace used for this investigation was a vertically mounted tubular Globar type with two concentric porcelain tubes inside the heating element. The control couple was located between the two porcelain tubes. The carbon monoxide atmosphere was introduced through a mercury seal at the bottom of the inner tube. On top, a glass head (with ground joint) provided access for samples and a long outlet tube prevented air from sucking back into the furnace. The charge used was iron 6 g, slag 5 g for the time series, or iron 9 g, slag 7 % g for the addition series. This slag-to-metal ratio of 0.83 approximates the average for blast-furnace practice, which commonly ranges from about 0.6 to 1.1. A crucible of AUC graphite containing the above charge was suspended by a molybdenum wire in the head and, after flush, was lowered to the center of the furnace as shown in Fig. 1. The cylindrical crucible was 2 in. long x % in. OD. The furnace was held within &3"C of the desired temperature for all the runs. The temperature was checked after the end of each run by flushing the inner tube with air and placing a platinum-platinum-10 pct rhodium thermocouple in the position previously occupied by the crucible; the temperature of the majority of the runs was much closer than the deviation specified above. The couple was checked against a standard couple which had been calibrated at the gold and palladium points, and against a Bureau of Standards couple. The carbon monoxide atmosphere was prepared by passing COz over granular graphite at about 1200°C. It was purified by bubbling through a 30 pct aqueous solution of potassium hydroxide and passing through ascarite and phosphorus pentoxide. The train and connections were all glass except for a few butt joints where rubber tubing was used for flexibility. The rate of gas flow was 25 to 40 cc per min. As atmospheric pressure prevailed in the furnace, the pressure of carbon monoxide was only slightly higher than the partial pressure thereof in the bosh and hearth zones of a blast furnace—by virtue of the elevated total pressure therein. Simultaneous samples of blast-furnace metal and slag were taken for these remelting experiments. The composition of each is given in the first line of Table I. There is considerable uncertainty as to the significant temperature in a blast furnace at which to compare experimental results. This uncertainty arises not only from lack of temperature measurements in the furnace, but also from lack of knowledge of the zone where the slag-metal reactions occur. (Do they occur principally at the slag-metal interface in the crucible, or as the metal is descending through the slag, or even higher as slag and metal are splashing over the coke?) The known temperatures are those of the metal at cast, which averages about 2600°F, and of the cast or flush slag, which is usually about 100°F hotter. To bridge this uncertainty, remelting temperatures were chosen as 1400°, 1500" (2732°F), and 1600°C. For the time series the duration of remelt was 1, 2, 4, 8, 17, or 66 hr; crucible and contents were quenched in brine. The addition series were quenched by rapidly transferring the crucible and contents from the furnace to a close-fitting copper "mold." Of incidental interest here is the fact that the slag wet the crucible

Jan 1, 1953

By Robert E. Green, Wolfgang Sachse

Simullaneous ultrasonic attenuation measurements of both quasishear waves propagating in single cryslals of aluminum indicate that, in the undeformed annealed state, the dislocation density is generally not uniform on all slip systems. Change oof attenuation measurements made during plastic defortnation of crystals , which possessed specific orientations ideal for studying the orientation dependence of dislocation damping, indicate that, for low strain levels, dislocation motion occurs on additional slip systems besides the primary one, even for crystals oriented for plastic deformation by single slip. THE sensitivity of internal friction measurements permits such measurements to be used successfully in studying the deformation characteristics of metal crystals. On the basis of experimental observations, T. A. Read1 was the first to associate internal friction losses with various dislocation mechanisms. Since that time further work2-' has been performed and a dislocation damping theory has been formulated by Granato and Lucke.6 In the amplitude independent region, this theory predicts the attenuation a to be dependent on an orientation factor O, a dislocation density A, and an average loop length L. if is a constant, independent of crystallographic orientation. For a given crystallographic orientation, changes in dislocation density and loop length give rise to the observed attenuation changes accompanying plastic deformation. The Granato-Liicke theory suggests the investigation of the orientation dependence of attenuation measurements in hopes of obtaining information to separate dislocation motion losses from other losses.7 An experimental study of the orientation dependence of attenuation in undeformed annealed single crystals should yield an insight into the uniformity of dislocation distribution throughout the entire specimen. A similar study on crystals plastically deformed in a prescribed fashion should give information about the alterations in the dislocation distribution on the slip systems activated during plastic deformation. The possible modes of elastic waves which can be propagated in aluminum,8 copper,9 zinc,10 and other hexagonal metals" have been calculated. Associated with each mode of wave propagation are dislocation damping orientation factors, which are based on the resolution of the stress field of that particular elastic wave onto the various operative slip systems in the material. These orientation factors have also been calculated as a function of crystallographic orientation in the papers cited above. Einspruch12 obtained agreement between predicted and observed attenuation values of longitudinal and shear waves in (100) and (110) directions of two undeformed aluminum crystal cubes. He ascribed the slight deviations between predicted and observed values to a nonuniform dislocation distribution, or to other loss mechanisms. In shear deformation of zinc crystals, Alers2 found that the attenuation of shear waves having their particle displacements in the slip plane was very sensitive to the deformation, while the longitudinal wave attenuation was affected only when the wave propagation direction was not normal to the slip plane. Using aluminum single crystals oriented for single slip, Hikata3 et al. found that during tensile deformation the change of attenuation of the shear wave (actually quasishear) having particle displacements nearly perpendicular to the primary slip direction exhibited the easy-glide phenomena, while longitudinal waves did not. Similar results were reported by Swanson and Green5 during compressive deformation of aluminum crystals. These results are in qualitative agreement with the calculated orientation factors for specimens of this orientation. In well-annealed, undeformed aluminum crystals, the damping is expected to be due to dislocations vibrating on all twelve slip systems. The orientation factors associated with this initial damping will be designated by O2 and O3, where a, represents the average orientation factor for the slow shear (or quasishear) wave and O3 represents the average orientation factor for the fast shear (or quasishear) wave. The calculation of these values for aluminum crystals by Hinton and Green8 shows that they vary very little as a function of crystallographic orientation—at most, by a factor of 2.47. If the dislocation density and loop length are uniform, then in the initial undeformed state, Here the subscript zero refers to the initial value of the attenuation. Also for aluminum, the calculations8 show that the orientation factors for primary slip only, associated with each shear wave, exhibit a sharp minimum for particular crystallographic orientations. A composite plot of the two shear wave orientation factors for primary slip only is shown in Fig. 1. Since these orientation factors are associated with dislocation motion occurring on the primary slip system only, the proper condition to check these factors might be attained by slightly deforming a single crystal oriented for primary slip. For dislocation motion on the primary slip system only,

Jan 1, 1969

By H. H. Wade, N. F. Schulz

The large quantities of iron-bearing materials, including taconite, semi-taconite," and other low-grade ferruginous materials occurring in Minnesota and elsewhere, constitute an important potential source of iron. Satisfactory grade and recovery of iron ore concentrate cannot ordinarily be obtained from these ferruginous materials by simple methods of beneficiation. Iron is distinctive in that the free metal and two of its oxides [magnetite (Fe,O,) and maghemite (gamma-Fe,O,) ] are strongly ferromagnetic. The successful magnetic separation of natural magnetite from taconite has already been established on a commercial scale. The iron in semi-taconite, how- ever, occurs largely as goethite (Fe,Os.H,O) and hematite (Fe90,) which do not respond to ordinary magnetic separation methods. Magnetic roasting converts these iron oxides to magnetite, which can, after liberation, be magnetically concentrated.

Jan 11, 1960

By D. D. Donald

C. J. Barber (U. S. Smelting Refining & Mining Co., Salt Lake City)—In his paper Donald describes how New Jersey Zinc Co. made surveys for a connection between the Ivanhoe and Van Mater shafts at Austin-ville, Va. Except to say that the two faces had to meet "accurately" on line and grade, Donald does not indicate the required precision. Assuming that there were 24 angles in the 11/2-mile traverse and 15 in the one-mile traverse, it can be shown that if the average error in plumbing each shaft was 230" and the average error in measuring each traverse angle was 210". then the average error at the point of -connection would have been about ±1.9 ft normal to the line between the shafts. This calculation assumes that any errors in the triangulation would be negligible compared with the errors in the plumbings and traverses, and it also neglects taping errors. With no constant errors or blunders, the latter would be important only in lines normal to the line between the shafts. To make the average error at the connection less than 1.9 ft would, therefore, require either reducing the error in the plumbings to less than ±30", or that in the traverse angles to less than ±l0", or fewer stations, or a combination of these. Referring briefly to the triangulation, because of the problem of fitting a new triangulation into older surveys of the district the orientation deserved some mention, even though the connection could have been made with an assumed bearing. It would be interesting to know how many triangles were required and what the average summation error was before making any adjustments and without considering the algebraic signs. Perhaps this is referred to indirectly in the statement that the maximum angular error distributed was 2". Turning to the shaft plumbings, it would be helpful to know how many men were employed and how long each shaft was in use. Donald says that the surface positions of W-2 and W-3 were carefully surveyed from the collar position of W-1, without indicating how this was done. The length of the backsight would be particularly important. There must have been some error in setting W-1 vertically below the stations in the headframes. How immovable were the headframes, especially the Van Mater, which appears higher than the Ivanhoe and subject to more vibration because of skip hoisting? Donald does not say whether the plumbing wires had been previously restraightened to minimize spinning (otherwise they behave like weak helical springs). The use of light steel weights is most surprising because there seem to be excellent reasons for using heavier, nonmagnetic weights. Did the shafts contain no steel sets, pipes, power cables, etc., which might attract steel? The plumbing method described by Donald was designed for deep shafts in South Africa but differed from the South African practice in two important respects. As described by Browne,6 in South Africa the line between the wires was made parallel to the long axis of the shaft, whereas in the Ivanhoe shaft the lines between the wires were diagonally across the shaft. The main reason given for the South African practice is to insure that the gravitational attraction between the wires and the rock walls is the same on both wires, and therefore does not affect the bearing of the line between them. It seems probable, however, that the effect of air currents might be minimized in the South African procedure, and might be serious with the wires in the diagonal position at the Ivanhoe shaft. In the South African case cited by Donald the wires were swinging freely (although the plumb bobs were sheltered from air currents) but in the Ivanhoe case they were dampened with the plumb bobs set in water. In the discussion of Browne's paper R. St. J. Rowland said:' It has been the practice for a long time to damp the oscillations by immersing the bobs in oil or water. The time per oscillation is thus increased, thereby extending the time taken to complete the work. The longer the suspended wire the less there is to recommend the practice . . . The theoretical time for one swing of a simple pendulum 1050 ft long is approximately 36 sec, which would be increased by dampening the plumb bob in water. Hence very few complete swings would be observed in the 5 min intervals used at the Ivanhoe shaft. In the two South African cases described by Browne, the length of plumb line in one shaft was 5425 ft, the calculated period of swing was 81.6 sec, the average actual period was 76.6 sec, and 94 complete swings were observed in 2 hr. In the other case the length of plumb line was 3116 ft, the calculated period of swing was 61.8 sec, the average period was 63.5 sec, and 86 complete swings were observed in 1 hr 31 min. Browne concluded that observations of more than 30 swings are not likely to result in sufficient gain in accuracy to be justified. Returning to the Ivanhoe and Van Mater plumbings, an objection to the method used is that all four azimuths were taken from fixed points instead of swinging wires, and that each pair of observations would— barring blunders— check closely, and so perhaps give a false feeling of security. In fact, it seems that only two azimuths were obtained from one plumbing, and not four as stated by Donald. Nevertheless, the tying in of each pair of wires from both sides of the shaft has much to commend it. Donald's description leaves the impression that if each shaft was plumbed only once, the engineers were fortunate indeed if the average error in the underground orientation was as little as 30". Because the survey was done over a period of three years, it seems likely that the plumbings were repeated, perhaps more than once. The underground traverse angles were measured by conventional methods, but because the number of angles in the overlapping traverses was not given, the angular closure given by Donald does not indicate the accuracy with which this was done. Donald's description of a method of taping lines of irregular length is welcome. The literature on taping is usually confined to lines of about one tape length, generally 100 ft. Such lines are rare in metal mining because the time, trouble, and cost of setting points at 100-ft distances underground are not warranted. (Nevertheless civil engineers may go to this expense

Jan 1, 1960

By Samuel Storchheim

IT was noted that variations existed in the magnetic properties, namely, coercive force, He, and rema-nence, Br, of 18/8 stainless steel wires of the same analysis when these wires were given the same percentage of reductiori of area at different rates of reduction. In order to determine the extent of these variations, a program was initiated whereby commercial 302 and 304 stainless steels were drawn with a wide variation of speeds. Ultimate tensile strengths and specific resistances, as well as the Hc-BT measurements, were determined. If variations of considerable magnitude were found, it was thought that the knowledge accrued from the investigation could probably aid in determining the particular drawing speed required to obtain desired properties for a given specification for a particular analysis of wire. Drawing Procedure Two specimens (set I, No. 302 and No. 304), the chemical analyses of which are given in Table I, were drawn at different speeds, namely, 45 to 3900 ft per min, directly from 0.016 in. diam wire to 0.004 in. diam wire, a 93.7 pct reduction of area. To obtain this high percentage of reduction, the wire at 0.016 in. was softened by annealing at 1150°C. It was then strung in a No. 16CF variable speed Vaughn drawing unit and passed through 13 B.&S. gage dies of successively smaller diameter, as shown in the accompanying table. Following this step, several hundred feet of the wire was drawn, at a particular speed, through the dies and wound upon a spool. Once the sample of wire was drawn at the desired speed, the spool with the finished sample was removed, tagged for later identification, and an empty spool was placed in the machine. Another wire sample was drawn at a different speed, after making the necessary adjustments upon the Vaughn unit. At the greater speeds, several thousand feet of sample were drawn to insure that the wire to be used for testing would be uniform. This was done because the desired speed was not reached instantly; the wire taking a short while to attain the required drawing rate. All speed measurements were made by placing a tachometer against one of the machine's pulleys during the actual drawing of the specimens. 84.4 pct reduction of area. The 0.072 in. diameter wire was also annealed at 1150°C. The process of obtaining samples was the same as described above. The only difference between the two was that the rates involved were not as extensive, set II covering a range of 625 to 1150 ft per min. Tensile tests were carried out for the 0.004 in. diam wires on a horizontal Scott Tensile Tester, while tensile tests for the 0.028 in. diam wires were made on a vertical Scott Tensile Tester. Each value listed in the tables represented the average of five samples with a maximum deviation of approximately 3 pct among the samples. Resistance per foot of the wires was determined by use of standard bridges accurate to the nearest hundreth of an ohm for the 0.004 in. wire, and to the nearest thousandth of an ohm for the 0.028 in. wire. The resistances per foot were then converted to resistivities by use of the following equation: P = RxCM where R is the resistance per ft in ohms per ft; CM, the area in circular mils; and P, the resistivity in ohms—CM. The values listed in the tables likewise

Jan 1, 1952

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE use of galvanic cells for the determination of oxygen activities has spread rapidly since the suitability of calcia-stabilized zirconia as a solid electrolyte material was first demonstrated by Kiukkola and Wagner.' In many of these investigations:-7 including several at ARL, the free-energy changes for various oxidation-reduction reactions involving the oxides FexO, NiO, and Cu2O have been measured as a means of assuring that a cell apparatus is functioning properly. As a result, a large quantity of data pertinent to the calculation of the high-temperature standard free energy of formation (?GO) of these oxides has been accumulated. AGFexo has been carefully measured in many independent investigations, using a variety of techniques, and consequently is accurately known. chipmans has used this informa-

Jan 1, 1968

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By R. L. Moment

The anisotropic elastic behavior of rolled beryllium sheet has been measured, using a pulse echo technique, and compared with X-ray diffraction data. Calculated elastic stiffness constants compared favorably with published values for beryllium single crystals which were attributed to the strong (0002) rolling plane texture. Variations of Young's modulus in the yolling plane could be associated with the velative distribution of (0002) planes out of their ideal position in the rollitzg pkule. WHEN a metal is subjected to cold working such as drawing, forming, or rolling, a crystallographic texture develops which can significantly alter its physical properties. One method for detecting this texture is X-ray diffraction, but Alers and Liu' have recently pointed out how the prediction of anisotropic physical properties from pole figures alone is not always accurate due to differences in interpretation. Variations in Young's modulus with orientation or, more completely, the values of the effective elastic constants of the worked metal, also serve to indicate the presence of a texture. In fact, as Alers and Liu' pointed out, calculated variations in Young's modulus for assumed orientations, when compared with experimental data, can be used to eliminate some of the uncertainty in interpretation of X-ray pole figures. Thus, elasticity measurements can serve not only to clarify any unusual elastic behavior of worked metal, but also to detect and in part determine the nature of its texture. X-ray determination of the texture of rolled beryllium has been reported by Smigelskas and Barrett,2 who found a strong texture of (0002) in the rolling plane with (1070) planes normal to the rolling direction. In the case of metal rolled at room temperature, they reported that [1010] directions also appeared at positions 60 and 120 deg from the rolling direction in the rolling plane, while in more recent work Keeler3 found these directions were also tilted towards the rolling plane. The texture for beryllium rolled at 80O0C, however, only showed (1010) planes normal to the rolling direction and the spread of (0002) planes out of the rolling plane was less. In looking for elastic anisotropy one might consider unidirectional rolling of a metal as introducing an or-thorhombic symmetry through reorientation of the grains, since the three deformations, compression, extension in the rolling direction, and extension in the cross direction, are orthogonal to each other and unequal in magnitude. Thus the rolled sheet could be treated like an orthorhombic single crystal and the nine stiffness constants of the elasticity tensor used to calculate the anisotropy of Young's modulus, the shear modulus and Poisson's ratio. In this case we could write: which is symmetric about its diagonal. Borik and Alers4 have recently used this approach on rolled die steel with very good results. They found, however, that instead of displaying orthorhombic elastic symmetry their specimens could be considered tetragonal in which case Cr1 = c22, c13 = Ca, and c44 =cjj. This conclusion was made solely on the basis of the measured tensor elements, and serves to point out the advantage of this method for studying the anisotropy of rolled metals. Their calculated values for Young's modulus as a function of angle in the rolling plane also checked very well with direct measurements made on different specimens using the resonance technique. In the present study, cross-rolled beryllium was used which had been unidirectionally rolled about 11 pct for the final reduction. This imparted a slight anisotropy in the rolling plane which was detected both by X-ray techniques and elasticity measurements. For purposes of discussion in this paper, the rolling direction is that direction in which the most reduction passes were made and cross direction is the normal to the rolling direction in the rolling plane. It was also decided to consider the rolled sheet as displaying orthorhombic symmetry for the purpose of obtaining elasticity samples with the direction defined as in Table I. Any change in the final symmetry attributed to the sheet would then be made on the basis of the measured elastic stiffnesses. The final data would then be compared with that expected from the X-ray study and that reported for beryllium single crystals. EXPERIMENTAL PROCEDURE Rolling Schedule. The samples used in this study were taken from a large sheet which, because of its size, had to be unidirectionally rolled for the final reduction. The resulting texture was that of cross-rolled metal with a slight unidirectional texture superimposed. A cast beryllium ingot, 9.500 in. sq by 3.325 in. thick, was cross-rolled to 81 pct reduction followed by unidirectional rolling for an additional 11 pct to give a total reduction of 92 pct. The thickness of the final sheet ranged from 0.265 to 0.280 in. Reduction up to 67 pct was done at 980°C and the final 25 pct at 870°C. Analysis for metallic impurities showed aluminum 0.06 pct, iron 0.19 pct, and silicon 0.11 pct, giving a beryllium purity of 99.64 pct.

Jan 1, 1968

By A. E. Jenkins, L. A. Baker, N. A. Warner

Rates oj decarburization of levilated Fe-C droplets conlaining 5.5 to 0 pct C have been measured at 1660°C. Gas mixtures of 1, 10, and 100 pct 0, with helium diluenl were used at velocities of 12.5 and 62.5 cm per sec. Rates were independent of carbon concentration in the mell and in good agreement with the calculated rule of oxygen diffusion through the gas boundary layer. The effects of flow rale and total pressure are as predicled and the rates are approxitnalely 2.5 times those with CO2 as oxidant. The mass-transfer correlation used incorporaled the efject of natural convection as well as forced conrection. Graphile spheres are shown to oxidize at the same rate as Fe-C droplets under the same experimental codlions. It is concluded that, for high carbon concentrations in the melt, the rate of- decarburizalion is controlled wholly by the rate of gaseous diffusion. Rate measurements with pure CO, are reported for low carbon concentrations where CO bubbles nucleate within the droplet. Under these circumstances the decarburi-zation decreased with carbon concentration and it is proposed that carbon diffusion is significant in conlrolling the decnvburization rate. In an earlier paper1 decarburization rate measurements were reported for levitated Fe-C alloys at 1660°C but with CO2 as the oxidant. The decarburization rate was found to be independent of carbon concentration in the melt but slightly affected by total pressure. The authors were unable to explain the slight pressure effect but in all other respects the results were consistent with control by diffusion in the gas boundary layer. Subsequent work has been directed at finding the reason for the slight pressure effect and whether the kinetics with oxygen as oxidant parallel those with CO2. Recently Ito and Sano2 have shown that with water vapor-argon atmospheres the decarburization rate is gaseous diffusion controlled until an oxide film appears on the surface. In this work the melts were contained in crucibles. MASS TRANSFER IN THE GAS PHASE In the earlier analysis1 only forced-convection mass transfer was considered. Subsequent recognition of the existence of some free-convection mass transfer explained the observed small effect of total pressure on the decarburization rate. Steinberger and Treybal3 and Kinard, Manning, and Manning4 have developed correlations involving the linear addition of the contribution of radial diffusion, free and forced convection. Steinberger and Treybal&apos;s correlation was chosen as the most applicable to the present work since it correlated most of the data available in the literature and handled the low Reynolds number region exceptionally well. The correlation for (Gr&apos;Sc) < 108 is where Nu&apos; is the Nusselt number for mass transfer based upon the total surface of a sphere in an infinite medium, G&apos; is the mean Grashof number for mass transfer defined by Eq. [2], Sc is the Schmidt number (µ/pDAB)f, Re is the sphere Reynolds number (dpu,pf/µf), p is the viscosity of the gas (poise), p is the density of the gas (g cm-3), Dab is the binary diffusivity for the system A-B (sq cm sec-&apos;), dp is the sphere diameter (cm), u is the approach velocity of the gas (cm sec-I), and subscript f denotes the property value is computed at the film temperature Tf defined by Tf = +1/2(To + Tr) where To is the specimen temperature and T, is the approach gas temperature (oK). Natural convection occurs when inhomogeneities exist in gas density. These may be caused by concentration gradients, temperature gradients, or both. In the present work the temperature gradient between the sphere and the bulk gas was very large and in some cases, for example the runs with pure oxygen, the concentration gradient was also appreciable. The Grashof number defined by Mathers, Madden, and piret5 was used since it took account of both temperature and concentration gradients: where Gr&apos; is the Grashof number for mass transfer (p2fgd3|-yA-yA|/µ2f), Gr is the Grashof number for heat transfer (p2f gd3p|To - T,]/µ2fTf), Pr is the Prandtl number (cpµ/k)f, g is the acceleration due to gravity (cm sec-&apos;f, a is the concentration densification coefficient (1/p)(ap/ayA)T, yA is the mole fraction of component A at the gas-metal interface, yA is the mole fraction of component A in the bulk gas stream, cp is the heat capacity of the gas per unit mass at constant pressure (cal g-I OK-&apos;), and k is the thermal conductivity of the gas (cal cm-&apos; sec-1 OK-1). Mathers et al. tested this combined Grashof number

Jan 1, 1968

By R. D. Vaughn

The limiting cases of non- Newtonian fluids flowing inside a concentric annular duct are developed without using a model of the fluid behavior. The solutions provide limits with which to test the various models of fluid behavior such as the power law and Bingham plastic models. The results of previous theoretical work are discussed in terms of limiting cases. This limiting case study also shows that experimental work on flow of non-Newtonian fluids in annular ducts should be confined to ducts for which the ratio of the radius of the inner wall to that of the outer wall is less than 0.3 and preferably less than 0.2. INTRODUCTION During the last 10 years the problem of laminar flow of non-Newtonian fluids in concentric annuli has received much attention large1y because of its application to the hydrodynamics of the wellbore. Recently solutions utilizing the power law1,2 and Bingham plasticl,3,4 models have been published. In this paper the method of limiting cases, which has been successfully applied to laminar-flow heat transfer516 will be applied to the problem of flow of non-time dependent, non-Newtonian fluids through annuli. This method permits solutions for the limiting cases to be made without using a model of unknown validity. The solutions, therefore, provide limits with which to test the various models which have been or will be proposed. A pertinent conclusion concerning the region of experimental work is also provided. DEVELOPMENT OF LIMITING CASES The limiting cases for the axial flow of fluids in concentric annuli may be defined with reference to Fig. 1. It is possible to define two limiting cases which pertain to the physical dimensions of the annulus. First, the annulus must degenerate to a circular pipe as the radius of the inner wall decreases or, as k = (k R/R) ? 0. Second, the annulus must approach the limit of parallel plates of infinite extent as the spacing between the inner and outer tubes becomes small in comparison with the radius R of the annulus, or as k?1. It is also possible to ascertain three limiting cases which pertain to fluid behavior. With reference to Fig. 2, as a fluid becomes progressively more pseudoplastic, the shear stress-shear rate relationship progressively approaches the indicated horizontal line more closely. At this limit the shear stress becomes independent of the shear rate. At the other extreme of increasingly dilatant behavior, the vertical asymptote is approached. Intermediate between these two limiting cases lies the case of the Newtonian fluid. Fluids which exhibit a yield shear stress also approach the limiting case of "infinite" pseudoplastic behavior. The remainder of the theoretical development is concerned with the description of and the solutions

By C.H. Lorig, M.C. Udy

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By M. C. Udy, C. H. Lorig

Through the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the genera1 effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. Literature Two general factors should be considered in a study of reduction of iron oxide: (I) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe304-FeO-H2-H2O, Fe3O4-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnasl published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at One temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1943

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should he considered in a study of reduction of iron oxide: (1) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe3O4-FeO-H2-H2O, Fe304-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By William J. McCaughey, Richard L. Barrett

FOR sixty years-in fact, ever since the inception of the basic steelmaking process -basic slags have been the subject of study by chemists, metallurgists and petrographers, with the purpose of providing a better understanding of the reactions between the slag and the metal during the refining process. The result of this work and of the researches of mineralogists and physical chemists into the chemistry of oxide systems is a considerable body of literature dealing not only with slags themselves but with equilibrium relationships in systems synthesized from pure components. Since any actual slag is a multicomponent system more complex than any yet worked out in the laboratory, a complete solution to the problem is still far away. The writers have recently published a paper1 which they believe sheds light on the role of the slag in the elimination of phosphorus and it is the purpose of the present paper to discuss the metallurgical applications of that work. Since the pioneer investigations on the constitution of basic slags carried on by Stead and Risdale, Carnot and Richards, Hilgenstock and others in the 1880&apos;s, a considerable body of literature on this subject has appeared. Many of the more important of these papers were summarized in the previous paper,&apos; therefore they will not be reviewed here. PETROGRAPHIC STUDY The present writers have had occasion, over a period of years, to examine petrographically a great number of basic steel- making slags having a very wide range of chemical compositions and made under various conditions of operating practice. Although certain of these slags exhibit some unusual features, it is a remarkable fact that the great majority of mature slags show certain typical characteristics, which persist throughout the wide range of chemical compositions. The typical mature slag usually appears under the microscope to consist of two phases. The phase of primary crystallization is light colored and doubly refracting. If separated mechanically and subjected to chemical analysis, it is found to consist essentially of SiO2, CaO, and P2O5. Sometimes, although not usually, two such silicate-phosphate phases are found. The other conspicuous phase is dark in color and optically isotropic, and occurs as the interstitial material between the grains of the light colored phase. This dark colored interstitial phase when analyzed is found to consist essentially of FeO,Fe2O3, MnO, and MgO. In some slags high in iron oxide, particularly those from low-carbon heats, dicalcium ferrite is found. This phase is dark reddish brown in color and anisotropic.

Jan 1, 1944

By Pradeep K. Rohatgi, David N. French, Surendar M. Jain, Clyde M. Adams

The effect of solute concentration and diffussivity on dendritic solidification of dilute binary aqueous solutions has been investigated; chlorides of sodium, potassium, lithiurn, and hydrogen were used as solutes. Dendrite spacings were measured in spherical droplets and in unidirectionally solidified specimens. In the droplets, the freezing rate is uniform over the entire specimen and remains constant from the beginning to the end of solidification. In the unidirec-tionally frozen specimens the freezing rate varies within a given volume of liquid during the solidification cycle; in addition, it varies with location uithin the specimen. Mass transport analysis has been used to calculate the supersaturation, AC, supercooling, AT, and transcerse growth velocity, V , of ice dendrites during solidijication from the dendrite spacings measured in the droplels. The ice dendrite spacing in a given solute increases lineary with the solule concentralion at a fixed freezing rate. The ualues of AC, AT, and V increase with an increase in solule concentration. The value of AT in the aqueous solution is of the same order of magnitude as in Al-Cu alloys of the same concentration; the dendrite spacings in Al-Cu alloys also increase with an increase in solute concentralion. For the jamily of aqueozrs solulions incestigaled, the dendrite spacing increases linearly with solute diffusivity at fixed values of concertralion and freezing ,rate. The values of ?C and ?T decrease, whereas the value of V increases with an increase in solule diffusicity. The measured dendrite spacings , L, can be expressed by the relatiun: L = K;(dfa/db) 4 K2C +K3D - K4 where dfs/d? is-change in fraction solid with time (freezing rate), C is solute concentration, D is solute diffusivit K1 = (14 * 4)pmin1&apos;2, K2 = (70 ± 10) pl (moles)- K3 = (24 r 3) . l05 psec (cm)-~. K. = -132 ± 10) 1. FREEZING of solutions is almost always an ehunmix-ing" process because the composition of crystallizing solid generally differs from that of the parent liquid. " Solute concentration and transport are therefore in]portant considerations in solidification of solutions. The influence of these factors on the dendritic solutions produced from metallic solutions is of practical significance since the properties of the solid aggre-gate are often strongly influenced by dendrite spacing.&apos;&apos;&apos; Alexander and Fthines3 found that dendrite spac- ings generally increase with solute concentration in several metallic systems. Michael and Bever1 have observed an increase in a aluminum dendrite spacings in dilute A1-Cu alloys. Rohatgi and AdamsJ have reported a linear increase in a aluminum dendrite spacings with increasing copper contents up to 28 pct in A1-Cu alloys. Bolling and Tiller"&apos; have theoretically examined the effects of solute concentration and diffusivity on the growth of cells and dendrites. Their analysis of dendritic growth assumes a steady-state growth and the maximum possible velocity for dendrite propagation. In addition, the quantitative analysis is restricted to dendrites of rotational symmetry and is therefore not directly applicable to the plate-shaped dendrites of ice obtained in the present study. There are practically no experimental observations of the effect of solute diffusivity on dendrite spacings in metallic systems. The reason appears to be the lack of experimental data on solute diffusion coefficients in liquid metallic solutions. The present work is concerned with the effect of solute concentration and diffusivity on dendritic solidification of dilute aqueous solutions: the solutes examined are potassium chloride. sodium chloride, lithium chloride. and hydrogen chloride. There were several reasons for selecting these solutes. The variation of dendrite spacing with freezing rate in these solutiolls is similar to that observed in A1-Cu alloys.8 These aqueous solutions have almost identical phase diagrams at dilute concentrations. Fig. 1. and the diffusion coefficients show very little variation with solute Concentration.9,10 Dendrite spacings were measured as a function of freezing rate. solute concentration. and solute diffusivity. Dendrite spacings were measured in two different types of freezing systems. droplet and unidirectional, respectively. In the droplet freezing system

Jan 1, 1970

By F. Weinberg, E. H. McLaren

Dilute binary alloys have been solidified under controlled thermal conditions, and solute distributions, temperatures during freezing and melting, and the position and morphology of the solid-liquid interfaces have been examined. Binary Zn, Sn, and Pb based alloys were investigated with solute additions of AgU°, AU°, Sb&apos;24, TlZo4, snH3, and Zns5. Approximately 150 cc of metal was used in each ingot. Appreciable solute segregation occurred in most of the ingots, depending on the solute concentrations, distribution coefficients. and freezing conditions of the alloys. Measurements were made of the general solute distribution by sectioning layers of material from the ingot circumference and counting the activity of each layer. Local segregation was detected by autoradiographic techniques. Freezing and melting curves for the same alloys were obtained by precision resistance thermometry. These curves are related to the corresponding measured solute distribution curves and those calculated from theoretical expressions. The position and morphology of solid-liquid interfaces during freezing were determined by both decanting and quenching techniques. The results indicate the manner in which freezing and remelting occurred under the conditions investigated. If an isomorphous dilute binary alloy is solidified or melted under equilibrium conditions, the concentration of solute in both solid and liquid would be uniform at all stages in the freezing process. The solute concentrations during freezing could be determined from the phase diagram of the alloy, and the freezing curves would have an alloy slope defined by the solidus and liquidus points. In practice, however, solidification under equilibrium conditions rarely, if ever, occurs, primarily because of low rates of diffusion in the solid and incomplete mixing in the liquid. As a result, the solute distribution and the shape of the freezing and melting curves obtained in a given system depends on a number of factors. These include, in addition to the extent of diffusion and mixing, the initial solute distribution and concentration, the distribution coefficient, the rate of freezing or melting, supercooling of the liquid, the morphology of the solid-liquid interface, and the effect of annealing. The purpose of the present investigation was to determine, experimentally, actual solute distributions and thermal curves for a series of dilute binary alloys, using tracer techniques to determine the solute distributions and precision resistance thermometry for the temperature measurements. In addition, observations were made of the positions and morphologies of the solid-liquid interfaces during freezing and remelting. The distribution of solute in a dilute alloy, assuming complete mixing in the liquid, and negligible diffusion in the solid, is given by1 where Co is the mean solute concentration of the alloy, C, is the solute concentration in the solidg is the fraction of the ingot solidified, and ko is the equilibrium solute distribution coefficient (assumed to be independent of concentration for dilute alloys). For the case of partial mixing, ko can be replaced by an effective distribution coefficient k. If solute transport in the liquid is assumed to be entirely due to diffusion, with negligible diffusion in the solid, then the solute distribution in the solid is given by Tiller et a1.&apos; as where R is the rate of advance of the solid-liquid interface, D is the solute diffusion coefficient in the liquid, and x is the position of the interface from the start of freezing. The temperature at the interface TI is related to the solute concentration of the solid at the interface C, by the expression where Tm is the freezing temperature of the pure solvent and ml is the slope of the liquidus for the binary alloy being considered. Accordingly, by relating TL to the actual temperatures measured in the present experiments, solute distributions can be deduced from the temperature measurements. Using the above expressions, the measured solute distribution of a given alloy may be compared to the theoretical distributions, as well as to the distribution calculated from the observed freezing curve. EXPERIMENTAL The solvent materials used in making up the binary alloys were C. P. New Jersey zinc (99.999 pct), Vulcan Extra Pure Tin (99.999 pet), and Tadanac lead (99.998 pct). The solute elements were of 99.99 pct purity or better, and were activated in the

Jan 1, 1963

By Merlon C. Flemings, Theodoulos Z. Kattamis

Examination was made of the distribution of tnanganese and nickel in colutrrnar dendrites of a cast low-alloy steel; more limited work was corzducted on chromium. Corresponding "segregrction ratios" were calculnted and shown to be relntivelv insensitive to cooling rate (&apos;&apos;segregation ratio" is defined (Is the ratio of maximum to minimum concentrations within a volume whose dimensions are the order of the dendrite-arm spacing). Isoconcentratiorl curves were determined by the electron micropvobe and by rt7etallografihic studies on specimens subjected to isothermal-transformation treatments. From construction of isoconcentration curves, morphology of columnar dendrites is descvibed as intermediate between Perfect rodlike and sheetlike morphologies. The study is extended to equiaxed dendrites and it is shown that the strcture of these dendrites is sittlilar in many respects to that of columnar dendrites. On the basis of tlze sheetlike morphology of dendrites, a simple model is pvoposed for calculation of honzogenization kinetics. Results of trzatllevlatical analysis brcsed on this utzodel are given. This analysis relates residual segregation to time at homogenization temperature; it is in agreement with experiment. Calculations are given which show that even for relatively rapidly cooled material (of 1-ine dendrite-artn spacing) treatmets at 1200°C or above are necessary to achieve slgxificant Izomogenization of elenlents other than carbon itz reasonable time (e.g., rnangclnese, nickel). Conlplete homogenization of carbon is obtnined at much lowev tenlperatures (below 870°C). IN dendritic solidification of castings and ingots, solute redistribution during freezing results in mi-crosegregation of most alloy elements. The micro-segregation is such that minimum solute concentrations occur at the center of dendrite arms and maximum concentrations occur between dendrite arms. Residual segregation after subsequent therma1 processing (homogenization) depends on maximum and minimum initial concentration, on the detailed geometry of the isoconcentration surfaces within interdendritic regions, on the diffusion coefficient of the solute, and on time of thermal processing. The objective of this work was to determine, for a low-alloy steel, maximum and minimum concentrations, and the geometry of isoconcentration surfaces, primarily in order to permit calculation of homogenization kinetics. Most of the work reported was conducted on Samples from a unidirectionally solidified, fully columnar ingot. This type of ingot is made by extracting heat during solidification from one face; techniques for accomplishing this have been discussed.&apos; Samples were taken at several locations, up to 5.75 in. from the mold chill face; the bulk of the work was performed on samples at 5.75 in. Alloy cast was, nominally, 0.4 pct C, 1.8 pct Ni, 0.8 pct Cr, 0.7 pct Mn, 0.25 pct Mo, 0.3 pct Si, and the balance iron. Brief study was also made on samples from an ingot which solidified with equiaxed grain structure. SAMPLE PREPARATION AND ANALYSIS Samples for electron-microprobe analysis were incorporated in mounts that included pieces of electrolytic nickel, chromium, and manganese, in order to normalize the intensities of these solutes in the specimens; also, a piece of electrolytic iron was included to measure the background. All specimens were polished in the usual metallographic manner. After the microprobe traces were made, the path was revealed by etching the specimens with picral. All microprobe analyses were made by point counting, integrating for 30 sec. The distance between points was fixed from 2 to 10 p, according to the precision desired in each case, the fineness of the structure, and the concentration gradient existing in a given area. (The distance was chosen 2 to 5 p near the maximum-concentration regions and 5 to 10 p near the minimum concentration.) The "take-off" angle for the A.R.L.-Model No. 21000 microprobe employed was 52.5 deg. Samples for metallographic analysis of isoconcentration curves were prepared by austenitizing at 1540°F for 20 min, quenching to the nose of the TTT curves (1200°F), heat treating isothermally at this temperature for a given time 0, and then quenching to room temperature. Due to concentration gradients existing in a dendritic structure, no transformation will take place for a given time 0 of isothermal heat treatment in the regions where the a.lloy concentration is higher than a given limit. Thus, the dendrite appears limited by an isoconcentration curve and can be made to appear to grow by varying the time of isothermal heat treatment.

Jan 1, 1965

By J. G. Patchett, R. W. Rausch

Fresh waters and the presence of clay in many Rocky Mountain and West Coast sands require special methods of log analysis. Archie&apos;s saturation equation requires addition of a shale correction term, and the SP equation must also be modified to account for clays. Suitable equations were developed several years ago, but have not been widely used due to the algebraic complexity. A computer-oriented method has now been developed to overcome this problem. The basic shaly sand equations are rearranged in four different ways to permit solution for various sets of available input data. Essential to application of the method is the correction of observed SP values to those that would be observed if the resistivity of the formation waters were exactly interchangeable with the activity. A graphic method for doing this is given. Where conditions require consideration of the effect of clay in the sands, the method presented has been found to improve the accuracy of water-saturation determinations. INTRODUCTION Log interpretation in many Rocky Mountain and West Coast basins is complicated by rapid vertical and lateral changes in water resistivity. Calculation of formation water resistivity from the SP curve becomes difficult in zones that contain clay, since changes in SP deflection may be due to changes in either clay content or water salinity. In hydrocarbon-producing reservoirs, the problem is further complicated because hydrocarbon saturation also reduces the SP.1 A log interpretation system using computers has been developed to provide a solution to this problem, based on equations proposed by de Witte.2 Four different simultaneous solutions of de Witte&apos;s equations have been made. Each solution method uses a different set of input data as independent variables. Thus, a choice of solution method is possible, depending upon the logs run and the availability of other data. Two of the solutions do not require a knowledge of water resistivity. This system is intended to be used primarily in multiple sandstone-shale sequences of low and moderate resistivities where the principal contaminant in the sandstones is clay. However, where sufficient regional data are available, interpretation in single-zone sandstone reservoirs can also be improved by using the method. THEORY AND HISTORY OF SHALY SAND ANALYSIS The log interpretation formula originally proposed by Archie3 in 1941 is applicable only to rock-fluid systems wherein the rock has negligible electrical conductivity. In 1949, Patnode and Wyllie4 showed that if the rock itself can be considered conductive due to the presence of clay, a different calculation approach is necessary. During the following years, this problem was investigated at great length, as was the related problem of the effect of rock conductivity on the SP.5-11 These investigations established functional relationships between SP, resistivity, water saturation and water resistivity for such a formation. Refs. 2 and 12 provide summaries of these studies. Unfortunately, practical use of these relationships required that water resistivity be known independently from the SP. Although log interpretation methods for rock systems containing clay were proposed at that time,&apos; they were not generally accepted for routine use. There are three principal reasons for this. First, in many field situations involving high-salinity water, rock conductivity may be neglected (even if present) without introducing appreciable error. This may be seen by considering the following expression for waier-saturated rock.&apos; 1/R2=1/R1+1/FRn....(1) where 1/R, is conductivity due to clay. As Rw becomes small, I/FRw becomes much greater than 1/R, which may be neglected. Where 1/R, may be neglected, the sandstone is called clean. If the term may not be neglected, the sandstone is termed dirty or shaly. For resistivity purposes, the classification between clean and shaly sands then depends not only upon the conductivity due to shale in the sand, but also upon the resistivity of the associated water (shale is used here to mean surface condition due to disseminated clay). A sand of given conductivity might safely be treated as clean in association with high-salinity water, but would require shaly sand methods if associated with fresher waters. Shaly sand methods are not required in many areas having saline waters; but in Rocky Mountain and West Coast sands having relatively fresh waters (often more than 0.3 ohm-m resistivity at formation conditions), the shaly sand methods are needed. Errors Rw calculations from the SP due to the presence of shale are likewise related to water salinity. In saline water formations drilled with fresh mud, the ratio of mud filtrate resistivity to water resistivity is high, the SP is large and the presence of shale can introduce large errors in water resistivity calculated by the conventional method. When the resistivity ratio is low, the errors are smaller. At zero SP, no error would result from shale. Thus, from the SP viewpoint, a given rock could be shaly if associated with a saline water, and clean in association with a fresh water, which is the opposite of the resistivity-oriented definition above.

By Edmund S. Davenport

The production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium. Materials and Methods The thorium employed in this investigation was made from pure thorium oxide (ThO2) by the Ca-CaCl2 reduction. The washed and dried metal powder was pressed into bars approximately 0.160 in. dia. and 10 in. long, at a pressure of 75,000 Ib. per sq. in. The bars were heat-treated in vacuum at 1175&apos; C. for 1 hr. This treatment yielded ingots sufficiently dense and coherent for mechanical working. Thorium has been successfully worked without a protective metallic covering, but for the purposes of this investigation it was more convenient to inclose the ingots in soft iron tubes and swage or roll cold to the desired sizes. The iron sheath was dissolved with nitric acid, leaving the cold-worked thorium exposed. Chemical Analyses Analyses of typical samples of the material used in this work arc given in Table 1. Thorium powder oxidizes in moist air, even at room temperature; no unusual precautions were taken to prevent such oxidation of the material used in this investigation. A certain amount of oxidation probably takes place during pressing; certainly during heat-treating unless a very slow heating schedule is employed. These factors account

Jan 1, 1930